Fisher & Paykel 88795 User's Manual
Contents
1. You must read the details concerning the method and frequency of cleaning There is a fire risk if cleaning is not carried out in accordance with the instructions Do not flamb under the rangehood Exhaust air must not be discharged into an existing flue used for exhausting fumes from appliances burning gas or other fuels The recomended minimum distance between the hob surface and the lowest part of the rangehood is 610mm 24 This should be increased to at least 660mm 26 preferably 685mm 27 if installed over a gas hob Attention should be given to ensure that any applicable regulations concerning the discharge of exhaust air is fulfilled If the supply cord of this equipment is damaged it must only be replaced by the manufacturer or it s service agent or a similarly qualified person in order to avoid a hazard Care should be taken when servicing the light panel due to a short switch wire max 895mm 35 1 4 gt 465mm 18 5 16 min 615mm 24 3 16 Fisher amp Paykel 914mm 36 565mm 22 1 4 ee ROBINHOOD LIMITED Electrical Rating 6 ZELANIAN DRIVE EAST TAMAKI 104735 issue E MANUFACTURED FOR 346W 1 44A Max at 230 240V 50Hz eo Gua ECN 04 101 PRE INSTALLATION Thank you for purchasing a quality stainless or iridium canopy rangehood We have a h2. CONTROL PANEL Fisher amp S Paykel D l iH O Q7 INSTALLATION INSTRUCTI OR Fan On Off Mid Speed High Speed Delay Switch Light On Off Titan Canopy Delay switch Fan will remain on at low mid or high speed for 5 mins before 88795 UK RH361 switching off automatically 88796 UK RH361M LIGHT REPLACEMENT 87978 NZ AUS RH361 a Switch off the power to rangehood 87979 NZ AUS RH361M b Use a small bladed screwdriver to prise off the light cover c Use a cloth to remove the bulb Do not touch the bulb with fingers d Replace with a new bulb using a cloth Do not touch the bulb with fingers Snap the cover back in place 2 e Halogen bulb 12Volt 20Watt required SB For other accessories parts or service please contact your local supplier Refer to the Warranty Certificate WARNINGS Care should be taken when removing filters in order to prevent the filter PLEASE READ THE ENTIRE INSTRUCTIONS BEFORE INSTALLING THE CANOPY falling and causing damage to the hob top Remove transport tape from the lights and filters before use nee is not intended for use by young children or infirm persons without PRODUCT DIMENSIONS Young children should be supervised to ensure that they do not play with the appliance 7 aa the appliance must be positioned so that the plug is 364mm 320mm There should be adequate ventilation of the room when the rangehood is used at Poa PN the same time as appliances burning gas or other fuels
3. d at least every two months Remove the grease filters and wash them ducting which requires 160mm 6 5 16 diameter hole either by hand or in the dishwasher using mild detergent in the ceiling Use lukewarm water and mild detergent to clean ans Sat Thi liancem ition hat the electrical components In high humidity and coastal environments cleaning shou e pigisaccac ible Bet Ea seit o out frequently CAUTION Never use abrasive or oil based liquid cleaners DUCTING Ducting accessories are not supplied The air outlet from the motor requires 150mm 6 round
4. igh standard of quality control and each rangehood is tested and approved before it leaves the factory IMPORTANT Please read prior to installation and operation Always switch the power off prior to installing servicing or cleaning the appliance Remove transport tape from the lights and filters before use Never use the appliance without the filters Please read the notes on general cleaning especially the filters Exhaust air must not be discharged into a heating flue or wall cavity unless the cavity is designed for that purpose Areas where the rangehood is installed that also have gas oil or coal fired heaters cooking surface ap 215mm INSTALLING MOUNTING BRACKET Align the centre of the installation bracket with the centre of the cooking surface recommend to use plumb bob Place the flat horizontal surface of the mounting bracket 215mm 8 1 2 above the installation height dia 1 Ensuring the mounting bracket is level mark and drill the holes in the wall Use the screws and plugs provided to attach bracket INSTALLING CHIMNEY BRACKETS Cut cornice to suit the chimney cover Align the centre of the chimney bracket with the centre of the cooking surface Mark and drill the holes in the wall and ceiling Use appropriate mounting screws or anchors installation height lt must be well ventilated to prevent a partial vacuum in the room This includes dia 1 gas hobs A partial vacuum in the ro
5. om could result in too high a concentration i of gas in the air INSTALLING THE CHIMNEY A rubber extrusion has been provided to hide any irregularities between WARNING the chimney and the canopy ceiling it is fitted by simply pushing it over the top and bottom visible edges of the chimney This steel edge may be All electrical work must be done in accordance with local and or national electrical codes as sharp so care must be taken to avoid damage to fingers If desired this applicable For safety this product must be earthed If you are unfamiliar with methods of extrusion may be omitted from the assembly l l installing electrical wiring employ the services of a qualified electrican Remove the protective plastic film from the chimney Prior to mounting the chimney determine the height required on the chimney The height Turn off power at service entrance before installing wiring or servicing this product can be adjusted by changing the screw on the back lip dia 2 Do not tighten the screws because the chimney needs to slide up when installing the canopy to prevent personal injury The canopy must be installed onto a solid wall or solid studs installing the canopy Mount the chimney to the ceiling bracket usin The canopy is heavy overall weight 65 Ibs 29kg Please ensure adequate care when e kA provi da y g g INSTALLING THE CANOPY Ensure the filters are removed from
6. the canopy Hang the canopy onto the installation bracket INSTALLATION OF UNIT Align the canopy so it is central to the cooking surface and lines up with the chimney cover NOTE Stainless steel and iridium is very easily Mark out the position of the two safety screw holes located on damaged during installation if abraided or knocked by tools the back panel Remove canopy drill the safety screw holes and fit wall plugs Read the instructions before starting the assembly Refit the canopy to the wall and secure using the appropriate Remove the filters to allow access to wall mounting holes mounting screws dia 3 Remove protective plastic film from the canopy and filters Ceiling height Installation height The unit is designed for 2290 to 2690mm 7 6 to 8 10 Refit the filters to the canopy 2290 to 2690mm PO high ceilings The chimney is telescopic and is designed for 7 6 to 8 10 615 to 895mm 24 3 16 to 35 1 4 adjustment CANOPY OPERATION Ascertain the desired installation height of the canopy NOTE Installation height ranges from 610 to 760mm Cooking surface 24 to 30 914mm 36 Care and attention should always be taken when cooking with oils alcohol etc which give off flammable vapours Pre used oil is especially dangerous in this respect Do not use an uncovered electrical grill Particular care must be taken with grease filters which must be periodically l i cee cleane
Download Pdf Manuals
Related Search