Firstech, LLC. SHF 2W-AS User's Manual
Contents
1. Page 7 Limited Lifetime Warranty Page 8 Registration Card Page 9 Page 2 of 9 The only two way vehicle security and remote starter system that tells you what s happening in your vehicle The only two way communication system between you and your vehicle with a complete information center built right in your LCD remote control 24 Hours Reservation On Off Antenna Silent Mode On Off Impact Report SHF 2W AS oe 1 W AS 2nd Car On Off e Pager On Off Transmission Indicator Lock Unlock Valet Mode On Off Alarm Function Silent Mode Remote Control Dual Shock Sensor Status LED s Active Passive Arming Remote Control Valet Remote Control Builtin Starter Kill Door Trigger Panic Mode Trunk Output Anti Code Grabbing Door Lock Unlock Fiirstece Key Ring Confirmation for Engine Start Blinking for Door Open Starter Function Superheterodyne Crystal Receiver Double Conversion Digital Processing sly Safety Shutdown Selective Runtime Programmable for Either Automatic or Standard Transmission Diesel Glow plug Sensing Factory Arm Disarm Parking Light Confirmation One Remote Two Car Op2. Page 6 of 9 4 NEUTRRAL SAFETY SWITCH Your vehicle should starts only in Parked or in Neutral position with the key If the vehicle starts in any other position the Manual Transmission Mode has to be activated Consult your dealer 5 ALARM TRIGGER Your alarm will be triggered in the following ways A Light Impacts will trigger the 1 stage of the Shock Sensor the siren will chirp 4 times and the parking lights will flash for a few seconds The LCD will not show anything for 1 stage of the Shock Sensor B Heavy impacts will trigger the system with 30 Sec of constant siren and flashing of the parking lights The Hammer in the LCD will show up and flash 6 times if it is in the Paging Mode C If a Door is opened the siren will go off and the parking lights will flash for 30 Sec The door in the LCD will flash 30 times if it is in the Paging Mode D Optional starter kill prevents the vehicle s starter from cranking 6 TRANSMITTER LEARNING PROCEDURE Steps 1 Put the system in Valet mode with key Ignition On and Off Three times with key within 3 Sec The parking light will flash once when it enters the Valet Mode Step 2 Once in the Valet Mode within 6 Sec choose one of the Lock options by pressing Button I for 1 2 Sec for normal locks Button Il for 2 Sec for double pulse unlock Button Ill for 2 Sec for lock pulse after Ignition turns Off for those vehicles that has factory Ignition control Door Loc
3. is automatically void if its date code or serial number is defaced missing or altered This warranty will not be valid unless you have completed the warranty card and mailed it to Firstech Inc within 10 days after purchase to the address listed on the card Page 8 of 9 Registration Card Name Address City State Zip Phone Number Home Office Place of Purchase Date of Purchase Purchase Model Purchase Price Vehicle Make Model How did you hear about this product Firstech Inc 230 E Potter Suite 8 Anchorage AK 99518 Page 9 of 9
4. sec Remote Start Stop Running time 15 or 25 minutes 24 45 for diesel Factory setting is 25minutes 45 for diesel If there is no response you are out of range If the door in the LCD flashes check to see if a Door is open the Hood is open the by pass switch is On or the Brake pedal is being pressed The vehicle will remain running for until Programmed time elapsed Button Il pressed for 2 seconds Break Pedal pressed Hood opened or By Pass Switch turned On Button Ill Press 2 Sec Trunk Release optional see dealer When the Button Ill is pressed for 2 Sec the trunk will open and the system will also Disarm Unlock the doors as well Button IV Press Sec Query The LCD will show the status of your vehicle Note Nothing will happen if the Button IV is pressed more than 1 2 Sec The LCD in the remote displays 5 different Modes Button I ll Press sec Mute Mode On Off When the Mute Mode is Off when SPK is indicated in the LCD Button I lll Press Sec Valet Mode On Off Valet Mode will shut down the alarm and the remote starter system Only the Lock Unlock will work in valet mode The Valet Mode can also be entered with the KEY Turning KEY to ON from ACC three times within 3 seconds Note The LCD will not display the Zz when the KEY is used to enter the Valet Mode Press Button I lll to exit Valet Mode Button Il lll_ Press 1 2 Sec Car Call Paging mode On Off Your remote will be
5. seconds Note The LCD will not display the Zz when the KEY is used to enter the Valet Mode Press Button I lll to exit Valet Mode Button Il lll_ Press 1 2 Sec Car Call Paging mode On Off Your remote will be paged when your vehicle is being tampered with The LCD will tell you whether it was tampered by Impact Sensor hammer flashing or Door being opened door flashing You will save the battery by turning off the Paging Mode CAR CALL will indicate in the LCD when this Mode is On Note The Pager will not respond to the first stage of the Shock Sensor Button Il IV_ Press 1 2 Sec 24hr Timer Mode On Off Your car will automatically start every One Two or Three Hours Factory Setting 3 Hrs If you want to change the Factory Settings see programming section Button Ill IV Press Sec Turbo Mode 2 car On Off Control Two vehicles with One Remote Why is it called Turbo This mode is used in different ways in other countries Factory Setting The remote control has been programmed to work either Turbo On Off indicated in the LCD Warning If you want to program more than One remote to a vehicle each time when you program a remote you must program the 2nd and 3 remote at the some time Up to three remotes to a vehicle 3 BY PASS SWITCH To shut Off the Remote Starter System by putting the by pass switch to On position By Pass switch on the Off position activates remote starting function
6. CompuStar SHF 2W AS USER S GUIDE Firstech Inc 230 E Potter St Suite 8 Anchorage AK 99518 1 907 563 8648 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device Page 1 of 9 1 INTRODUCTION Thank you for choosing COMPUSTAR a state of the art TWO WAY alarm remote start systems for your vehicle We at FIRSTECH INC are constantly researching and developing to make you and your vehicle safe and more comfortable SECURITY amp COMFORT that s what FIRSTECH INC is all about TABLE OF CONTENTS Operation Remote Functions For Automatic Transmission Page 4 Operation Remote Functions For Manual Transmission Page 5 By Pass Switch Page 6 Neutral Safety Switch Page 7 Alarm Trigger Page 7 Transmitter Learning Procedure Page 7 Programming Options With Remote
7. ctory setting No ignition lock Automatic Arming Lock upon completion of reservation and Active Arming The status LED will begin to flash after 3 seconds upon locking the doors The Starter Kill Optional feature see your dealer will take into effect The shock sensor will be in Impact Watch Mode for 30 seconds upon Arming Upon Disarming if siren chirps more than Two times the system has been triggered while armed 3 chirping by Shock sensor 4 chirping by Door sensor If the vehicle has a dome light delay circuit and you have to wait until the dome lights go off before you Arm Lock the car consult your authorized dealer Note Passive Arming The system also can be programmed for Passive Arming The system will check the doors If the doors are all closed the system will arm itself in 30 seconds Warning Do not press Button for more than 1 2 Sec See next Button Press 2 Sec Panic To turn off Panic press Button for Y second Panic is also a Car Finder Button Il Press 2 sec Remote Start Stop Running time 15 or 25 minutes 24 45 for diesel Factory setting is 25minutes 45 for diesel Also the factory setting is automatic Arming Lock upon completion of reservation If there is no response you are out of range If the door in the LCD flashes without starting the vehicle when the Reservation Mode has not been set Also check to see if a Door or the Hood is open the by pass switch On or the Parkin
8. eration Ignition Controlled Door Locks lt FCC ID N99 SYSTEM N99 REMOTE F 1 OPERATION REMOTE FUNCTIONS FOR AUTOMATIC TRANMISSON Please take time to read the owners manual If you have any question please contact your authorized dealer Also refer to the FUNCTION printed on the back of your remote Button I Press Sec Arm Lock Disarm Unlock If there is no response you are out of range All doors have to be closed if not the door in the LCD will flash Factory setting No ignition locks Active Arming The status LED will begin to flash after 3 seconds upon locking the doors The Starter Kill Optional feature see your dealer will take into effect The shock sensor will be in Impact Watch Mode for 30 seconds upon arming Upon disarming if siren chirps more than two times the system has been triggered while armed 3 chirping by Shock sensor 4 chirping by Door sensor Note The system also can be programmed for Passive Arming The system will check the doors and if the doors are all closed the system will arm itself in 30 seconds If the vehicle has a dome light delay circuit and you have to wait until the dome lights go off before you Arm Lock the car consult your authorized dealer about Passive Arming Warning Do not press Button for more than 1 2 Sec See next Button I Press 2 Sec Panic To turn off Panic press Button for 2 second Panic is also a Car Finder Button Il Press 2
9. g Break released The vehicle will remain running for until Programmed time has elapsed Button Il pressed for 2 seconds Parking Brake released Hood opened or by pass Switch turned On IMPORTANT 1 The vehicle must be in the NEUTRAL position 2 The vehicle windows must be rolled up 3 Do not set the reservation mode with any people in the vehicle 4 Do not remote start with any people in the vehicle Note The system is not recommended for vehicle with removable tops Reservation Mode must be set for Manual Transmission vehicles to Remotely Start Steps1 After arriving at the destination and before turning the engine OFF shift the transmission to the Neutral position Step 2 Activate your parking brake Step 3 Remove the key from the ignition The engine will remain running Step 4 Exit the vehicle and close the door within Two minutes from step 3 Then the engine will shut Off and Reservation Mode is now complete Your vehicle is now ready for remote starting However the reservation mode will be cancelled if Door has been opened or CompuStar has been put in Valet mode after Step 4 in which cases you have to start the vehicle with the key and repeat the above 4 steps if you want to restore the Reservation Mode Page 5 of 9 Note If you try to remote start the vehicle when the Reservation Mode has not been set or cancelled the system will not start The parking light will flash Three times and the Doo
10. hirps confirming Step 3 Step 5 Option 3 A Passive Arming After the last door is closed the system will chirp every 10 seconds and Arm itself after 3 warning chrips Press Button for Sec Option 3 B Semi passive arming The system will Arm itself after disarm like Option 3 A except if a door has been opened after disarm the system will not Passively arm Press Button ll for 2 Sec Option 3 C Active arming System wills arm disarm only by the remote Press Button IV for Sec Four chirps confirming step 5 Step 6 Option 4 A If you enter 24Hr mode the system will start the vehicle every hour Press Button for Sec Option 4 B In 24Hr mode every 2 hour Press button II for 2 Sec Option 4 C In 24Hr mode every 3 hour Press Button Ill for 2 Sec Option 4 D Not to program 24Hr Mode Press button IV for 1 2 sec Five chirps confirming step 6 NOTE Go through the procedures Step by Step If the system dose not give the confirmation chirps go through the Programming Option again Page 7 of 9 LIMIED LIFETIME WARRANTY Firstech Inc Warrants to the original purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances for the period of time that the original owner of this product owns the vehicle in which it is installed except that the remote controller unit for the period of one year from the date of installation to the original owner of this p
11. k and Unlocks the Door when the Ignition is turned Off Button IV for 1 2 Sec for 4 second door lock pulse The parking light will flash twice to confirm step 2 Step 3 Program 2 remote or 3 remote by pressing any button The system will program up to 3 remotes The parking light will flash once to confirm step 3 Note Step 3 will remove any of the previous programming of the remotes Each time when you program a remote you have to program the 2 or 3rd remote also even if it was programmed previously 7 PROGRAMMING OPTIONS WITH REMOTE Step 1 Place the key in the Ignition and turn to the ON potion vehicle not running This means that there should be 12v at IG1 and nothing at the Tach sensing wire or Alternator sensing wire Step 2 Press the buttons and IV for 1 2 Sec The siren will chirp once now you are in the Programming Mode Step 3 Option 1 Ignition Lock locks all doors after starting Press button for 1 2 Sec to select Option 1 Press button IV for 2 Sec to not select Option 1 Two chirps confirming step 3 Step 4 Option 2 locks all doors after reservation Manual Transmission only Please go over the procedure for Reservation Mode for the Manual transmission If you choose Option 2 the doors will lock when you exit the vehicle and close the door Option 2 is recommended Press button for Sec to select Option 2 Press button IV for 2 Sec to not select Option2 Three c
12. paged when your vehicle is being tampered with The LCD will tell you whether it was tampered by Impact Sensor hammer flashing or Door being opened door flashing You will save the battery by turning Off the Paging mode CAR CALL will indicate in the LCD when this mode is on Note The Pager will not respond to the first stage of the Shock Sensor Button Il IV Press 1 2 Sec 24Hr Timer Mode On Off Your car will automatically start every One Two or Three Hours Factory Setting 3 hrs If you want to change the Factory Settings see programming section Page 4 of 9 Button Ill IV Press Sec Turbo Mode 2 car on off Control Two vehicles with One Remote Why is it called Turbo This mode is used in different ways in other countries Factory Setting The remote control has been programmed to work either Turbo On Off indicated in the LCD Note If you want to program more than one remote to a vehicle every time you program a remote you must program the 2 and 3 remote at the same time Up to three remotes to a vehicle 2 OPERATION REMOTE FUNCTIONS FOR MANUAL TRANSMISSION Please take time to read the owners manual If you have any question please contact your authorized dealer Also refer the FUNCTION printed on the back Button I Press Sec Arm Lock Disarm Unlock If there is no response you are out of range All doors have to be closed If not the door in the LCD will flash Fa
13. r in the LCD will start flashing to inform you that the Reservation Mode has been cancelled or not been set Canceling Reservation Mode If you do not want to set the reservation mode shut off the engine before you exit the vehicle The engine will shut off if a you do not activate your Parking brake when you turn your key to Off position b release your Parking brake while engine is running or if c you press Button Il between step 3 and 4 Note The Reservation Mode will cancel if the Door opens or CompuStar has been put in Valet mode after Step 4 in which cases you have to start the vehicle with the key and repeat the above 4 steps if you want to restore the Reservation Mode Button Ill Press 2 Sec Trunk Release optional see dealer When the Button Ill is pressed for 2 Sec The trunk will open and the system will also Disarm Unlock the doors as well Button IV Press Sec Query The LCD will show the status of your vehicle Note Nothing will happen if the Button IV is pressed for more than 1 2 Sec long The LCD in the remote shows 5 different Modes Button I ll Press Sec Mute Mode On Off When the mode is Off when SPK is indicated in the LCD Button I lIll Press Sec Valet Mode On Off Valet Mode will shut down the alarm and the remote starter system Only the Lock Unlock will work in Valet Mode The Valet Mode can also be entered with the KEY Turing KEY to ON from ACC three times within 3
14. roduct When the original purchaser returns the product to the retail store where it was purchased or pre paid postal to Firstech Inc 230 E Potter Suite 8 Anchorage Alaska 99518 USA within the warranty period and if the product is defective Firstech Inc will at its option repair or replace such TO THE MAXIMUM EXTENT ALLOWED BY LAW ANY AND ALL WARRANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND OR ANY AND ALL WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OR AHY AND ALL WARRANTY OF NON INFRINGEMENT OF PATENTS IN THE UNITED STATES OF ANERICA AND OF ABROAD NEITHER THE MANUFACTURER OR ANY ENTITIES CONNECTED THEREWITH SHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO ANY CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES DAMAGES FOR LOSS OF TIME LOSS OF EARNINGS COMMERCIAL LOSS LOSS OF ECOMONIC OPPORTUNITY AND THE LIKE NOTHWITHSTANDING THE ABOVE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary State to State IMPORTANT NOTE A product s warranty
Download Pdf Manuals
Related Search