Home

Finlux 32F8072-T User's Manual

Contents

1. E NOTE When connecting a device via the Side AV input you must use the supplied connection cables to enable connection See the illustrations above YPbPr can be used only when you connect a device that has a YPbPr output through the PC input with YPbPr to PC cable YPbPr to PC cable is not supplied When the connection is made switch to YPbPr source To enable PC audio you will need to use PC YPBPR AUDIO CONNECTION WHITE amp RED inputs If an external device is connected via the SCART socket the TV will automatically switch to AV mode When receiving DTV channels Mpeg4 H 264 or while in Media Browser mode output will not be available via the scart socket When using the wall mounting kit optional we recommend that you plug all your cables into the back of the TV before mounting on the wall Insert or remove the CI module only when the TV is SWITCHED OFF You should refer to the module instruction manual for details of the settings Obtain the Conditional Access Module CAM and the viewing card by subscribing to Digiturk or D Smart Insert the CAM and then the viewing card to the slot that is located in the terminal cover at the rear side of the TV The module should be correctly inserted it is impossible to insert fully if reversed The CAM or the TV terminal may be damaged if the CAM is forcefully inserted English 7 Using a Conditional Access Module IMPORTANT Insert or remove the CI module only when the TV is SWITCH
2. There was no operation performed for a long time Shut down If the TV has been left on and not been operated for 4 hours the TV will go into standby When you next switch on the following message will be displayed Standby Cause No Operation Press OK to continue 8 Inserting the Batteries to the Remote 1 Lift the cover on the back of the remote upward gently 2 Install two AAA batteries Make sure to match the and ends of the batteries in the battery compartment observe the correct polarity 3 Replace the cover Connect Power amp Antenna IMPORTANT The TV set is designed to operate on 220 240V AC 50 Hz socket After unpacking allow the TV set to reach the ambient room temperature before you connect the set to the mains Plug the aerial cable into the ANT socket on your TV Switching On Off To Switch the TV On Connect the power cord to the 220 240V AC 50 Hz To switch on the TV from standby mode either Press the acy button P P or a numeric button on the remote control Press the side function switch until the TV comes on from standby To Switch the TV Off Press the iy button on the remote control or press the side function switch until the TV switches to the standby mode To power down the TV completely unplug the power cord from the mains socket Note When the TV is switched to standby mode standby LED can blink to indicate that features such as Standby Search Over Air D
3. P A or Y to navigate between the items on Portal screen Press the OK button to confirm your selection Press the BACK button to go to the previous screen Press the EXIT button to quit the Internet portal mode Digital Teletext Press the button The digital teletext information appears Operate it with the coloured buttons cursor buttons and the OK button The operation method may differ depending on the contents of the digital teletext Follow the instructions displayed on digital teletext screen When the button is pressed again the TV returns to television broadcast English 20 Software Upgrade Your TV is capable of finding and updating automatically via the Aerial signal or over the Internet Background search and upgrade mode While the TV is connected to the Internet if new software is found it downloads the upgrades automatically when the TV next powers on from standby 3 00am search and upgrade mode While the TV is connected to an aerial signal If Automatic scanning in the Upgrade Options menu is enabled the TV wakes up at 03 00 and searches broadcast channels for new software upgrades If new software is found and downloaded successfully the next time the TV powers up it will have the new software version Note If the TV fails to come on after the upgrade unplug the TV for 2 minutes and plug in again Troubleshooting amp Tips No power If your TV has no po
4. If the domain is invalid this might cause problems while browsing files in DLNA mode English 21 Information for Users on Disposal of Old Equipment and Batteries European Union only These symbols indicate that equipment with these symbols should not be disposed of as general household waste If you want to dispose of the product or battery please consider the collection systems or facilities for appropriate recycling Notice The sign Pb below the symbol for batteries indicates that this battery contains lead K X EEE Battery Products Specifications TV BROADCASTING PAL SECAM B G D K K I F L L DIGITAL RECEPTION DVB T MPEG2 DVB T MPEG4 HD DVB T MHEG 5 Engine for UK only DVB C MPEG2 DVB C MPEG4 HD DVBT 2 MPEG2 DVBT 2 MPEG4 HD RECEIVING CHANNELS VHF BAND NIII UHF BAND U HYPERBAND NUMBER OF PRESET CHANNELS 1000 CHANNEL INDICATOR On Screen Display RF AERIAL INPUT 75 Ohm unbalanced OPERATING VOLTAGE 220 240V AC 50 HZ AUDIO German Nicam Stereo AUDIO OUTPUT POWER W 10 THD 2 x 6 POWER CONSUMPTION W 65 W max PANEL 16 9 Licence Notifications TRADEMARK ACKNOWLEDGMENT Manufactured under license from Dolby Laboratories and the double D symbol are trademarks of Dolby Laboratories Q DOLBY DIGITAL PLUS DLNA the DLNA Logo and DLNA CERTIFIED are trademarks service marks or certification marks of the Digital Living Network Alliance Salina HDMI the HDMI
5. USB Is too Slow If a USB is too slow message is displayed on the screen while starting a recording try restarting the recording If you still get the same error it is possible that your USB disk does not meet the speed requirements Try connecting another USB disk Internet Connection Not Available DLNA Mode Not Operating If the MAC address a unique identifier number of your PC or modem has been permanently registered it is possible that your TV might not connect to the internet In such a case the MAC address is authenticated each time when you connect to the internet This is a precaution against unauthorized access Since your TV has its own MAC address your internet service provider cannot validate the MAC address of your TV For this reason your TV cannot connect to the internet Contact your internet service provider and request information on how to connect a different device such as your TV to the internet It is also possible that the connection may not be available due to a firewall problem If you think this causes your problem contact your internet service provider A firewall might be the reason of a connectivity and discovery problem while using the TV in DLNA mode or while browsing via DLNA Invalid Domain Ensure that you have already logged on to your PC with an authorized username password and also ensure that your domain is active prior to sharing any files in your DLNA server program on your PC
6. Page Address Bar Add History Bookmarks Zoom e ig 4 d if WIKIPED Las emctelogs EDLA a libry Remote control shortcuts Quick Access Zoom in out Back Home e To navigate the web browser use the arrow buttons pages and these will take you to the appropriate on the remote control Press OK to continue pages e After First time installation predefined web sites and When you scroll the pointer down to the middle of the logos will be displayed on the browser s access page screen the remote control s shortcuts will be shown see image above To add a desired web page to Use the zoom shortcut buttons or the zoom menu the quick access page whilst on the website you to zoom in or zoom out wish to add select the Add menu and select Quick H i r clear all browser data from Aocese pitta You can clear cookies or clear all browser data fro Po the settings menu e If you want to add bookmarks select this item while the desired web page is on the screen e Your TV is compatible with USB mice Plug your mouse or wireless mouse adaptor to the USB Add input of your TV e To view your browsing history click the history button You can also clear your browsing history Bookmarks Quick from here Access History Clear History e You can navigate the web browser in three ways Access Date item First enter any URL in the address bar spp rte 2 09 08 2012 Wikipedia 3 09 08 2012 http
7. a store you can activate this mode Whilst Store Mode is enabled some items in the TV menu may not be available DLNA DLNA feature allows you to share files stored on your smartphone If you have a DLNA compatible smartphone and the appropriate software is installed you can play photos on your TV See instructions of your sharing software for more information Power Up Mode Standby The TV powers up into Standby mode when the TV is plugged into the mains Last State The TV powers up into On mode when the TV is plugged into the mains and the last channel source is selected Virtual Remote Optional Enable or disable the virtual remote feature Netflix You can view your ESN number and deactivate Netflix ESN number is an unique ID number for Netflix created especially to identify your TV English 14 Electronic Programme Guide EPG Some but not all channels send information about the current and next programmes Press the Ca button to view the EPG menu Tue 08 05 14 29 T E oa Fieri erty els Programme Guide 6 ITV2 EH Planet s Funni Britain s Got Talent 7 BBC THREE 9 BBC FOUR 10 ITV3 11 Pick TV inte On the Buses On the Bu Lael Nothing To Declare Nothing To Declare Up Down Left Right Navigate EPG OK Displays programme options Displays in detail information on the programme selected GREEN Switches to List Schedule EPG YELLOW Switches to T
8. case OSD will display the programmed events for recording Press Il STOP button to cancel instant recording Note You can not switch broadcasts or view the Media Browser during the recording mode Watching Recorded Programmes In the main menu use lt or buttons to select Media Browser Highlight the Recordings Library using lt or button and press the OK button to enter the Recordings Library Select a recorded item from the list if previously recorded by using button Press the OK button to view the Play Options Select an option by using or OK buttons Play Options Resume Play from offset Available playback options e Play from start Plays the recording from the beginning e Resume Resumes Playback from the point at which you stopped playback previously e Play from offset Specifies a playing point Note Viewing main menu and menu items will not be available during the playback Press the I STOP button to stop a playback and return to the Recordings Library Slow Forward If you press Ill PAUSE button while watching recorded programmes the slow forward feature will be available You can use PP button to slow forward Pressing PP button consecutively will change slow forwarding speed Recordings Library To view the list of recordings select Recordings Library and press the OK button The Recordings Library will then be d
9. displayed on the screen If you are satisfied with the order of channels press the OK button to quit the channel list and watch TV Channel list Satellite Analoque 1 BBC ONE 2 BBC TWO 3 ITV1 4 Channel 4 5 Channel 5 6 ITV2 7 BBC THREE 9 BBC FOUR 10 ITV3 11 Pick TV WB Digital AeriaVAnalogue Digital Cable Analogue Satellite Analogue keme Seer rere Media Playback via USB Input You can connect a USB hard disk drive or USB memory stick to your TV by using the USB inputs of the TV This feature allows you to play files stored in a USB drive 2 5 and 3 5 inch hdd with external power supply external hard disk drives are supported IMPORTANT You should back up your files before making any connections to the TV set in order to avoid any possible data loss The Manufacturer will not be responsible for any file damage or data loss It is possible that certain types of USB devices e g MP3 Players or USB hard disk drives memory sticks may not be compatible with this TV The TV supports FAT32 and NTFS disk formatting but recording will not be available with NTFS formatted disks Note While formatting a USB hard disk that has 1TB Tera Byte or more file capacity you can experience problems with the formatting process Quickly plugging and unplugging USB devices is a very hazardous operation This may cause physical damage to the USB player and the USB device itself Do not pull out the USB module
10. secssscnorisiesiniena sasan 21 OPECINCANONS twsctosiessexeecacescchatsnaneassedstussedootescctacnaccaaies 22 Licence Notifications cccccccccceeseeseeeeeeeeeees 22 Appendix Nero MediaHome Installation 23 Getting Started with Skype cccccccsssseseeeeees 27 Sign In amp Sign Up NOW se ccciccsntisesscccaciiwntsmnstionweds 28 Adding a COMMLACE sstantdans cusronaiteinniidabunianiipsaGtantesiadsdete 29 Recent TI StONY calniamianiaciionentanavianinminetsimtentamenenia 29 PRG NOMS cacas nonunion ea anais 30 dose mineke M E 31 Dialing PNOMSS irediumituicadte ror tanaiventamidednaneniadedienia 31 SS E E See neti hata E 31 Appendix B PC Input Typical Display Modes 32 Appendix C Supported File Formats for USB Media OWED cao eercstaseadia lore pacdsoncadeet aatoienubehorneneataceons 39 Appendix D Supported DVI Resolutions 34 Appendix E SKY Remote Control Code 34 Appendix F AV and HDMI Signal Compatibility Input Signal TYOES ssijsccssccsccdeenacescectiestascadecteesteceues 35 important IS WUC HO Mo ts sensi cescisicsalercennecontenvanetene 36 English 1 Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL AA The lightning flash with arrowhead symbol within an equilateral t
11. while playing a file Media Browser Menu You can play photo music and movie files stored on a USB disk by connecting it to your TV Connect a USB disk to one of the USB inputs located on the side of the TV Media Browser Recordings Library The USB selection OSD will be displayed on the screen Press the MENU button and select the Media Browser tab by using the Left Right and OK buttons The Main media browser screen will be displayed You can display the approprite content by selecting the Video Music or Picture tab Follow the button indications under each on screen menu for media playback features Pressing the MENU button while in the Media Browser mode will access the Picture Sound and Settings menu options Pressing the MENU button again will exit from this screen You can set your Media Browser preferences by using the Settings menu English 10 KE cei HB ipie Bec Ei Note If two USB devices are connected to the TV at the same time the first USB device connected to the TV will be named USB drive 1 Select the drive by using or Nw buttons and press OK Changing Image Size Picture Formats Programmes can be watched in different picture formats depending on the transmission received You can change the aspect ratio image size of the TV for viewing the picture in different zoom modes Press the ta button repeatedly to change the image size You can shift the screen up or down by
12. you are watching your TV or operating the Skype application e A Skype camera can be sold separately is required to get the full benefit of Skype s features If you do not already have one you will need to purchase a camera compatible with Vesca100 to get the full benefits of Skype Note When you turn on the TV and no users have been set up for Skype the image shown to the side will appear Skype started pl int on screen ugged into No default user Skype Licence Notification Skype is a trade mark of Skype or its related companies This product application has not been approved or endorsed by Skype Skype Communications S a r or any of their related companies No emergency calls with Skype Skype is not a replacement for your ordinary telephone and can t be gt used for emergency calling Select the Skype app from the portal section to start a conversation English 27 Sign In amp Sign Up Now plugged into Skype You can create a Skype account using this app in the Sign In amp Sign Up Now menu if you don t already have one If you already have a Skype account enter your name and password correctly Select Sign In and press OK To use the Skype application you need a Skype account If you have a Skype account and you forgot your password press the Red button to view the reset password screen After successfully logging in to your account the contact list will be di
13. 080P 50fps Other 1080P 30fps 50Mbit sec l 20Mbit sec AC3 EAC3 LPCM WMA sec jp ipe MAX WxH 14592x12288 Up to 8 MegaByte Appendix D Supported DVI Resolutions When connecting devices to your TV s connectors by using DVI converter cables not supplied you can refer to the following resolution information 640x400 T M M 640x480 51010 e100 K 832x624 1024x768 K 1152x864 K 1152x870 1280x768 1360x768 1280x960 1280x1024 1400x1050 1440x900 1600x1200 1680x1050 1920x1080 NINIJNIJNININININIANIN 1920x1200 Appendix E SKY Remote Control Code The Sky Code is 065 1 Turn your TV on 2 Press TV on your Sky remote control handset 3 Hold down SELECT and the RED button together for about two seconds until the red light on the Sky remote control blinks twice 4 Key in 065 The light on the Sky remote control should blink twice 5 Press the STANDBY button on your Sky remote control If your TV switches off press SELECT The light on the Sky remote control blinks twice Now try the other functions English 34 Appendix F AV and HDMI Signal Compatibility Input Signal Types Source Spa Signals ANEEL G PAL NTSC 60 RGB 50 60 EXT 1 SCARTI SECAM PAL EXT 1 NTSC 60 SCART2 SECAM PAL 50 60 Side AV NTSC 60 SECAM YPbPr gt 480P 5761 50Hz 576P 720P 720P 10801 10801 4801 480P 5761 50Hz 576P 720P 7
14. 20P 10801 10801 1080P X Not Available O Available In some cases a Signal on the LED TV may not be displayed properly The problem may be an inconsistency with standards from the source equipment DVD Set top box etc If you do experience such a problem please contact your dealer and also the manufacturer of the source equipment English 35 Important Instruction For your own safety read following instruction carefully before attempting to connect this unit to the mains supply MAINS AC OPERATION The wires in the mains lead are coloured in accordance with the following code GREEN amp YELLOW Earth if there is earth cable BLUE Neutral IMPORTANT As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug proceed as follows The wire which is coloured green and yellow must be connected to the terminal which is marked with the letter E or by the earth symbol or coloured green or green and yellow The wire which is coloured blue or black must be connected to the terminal which is marked with the letter N or coloured Black The wire which is coloured brown or red must be connected to the terminal which is marked with the letter L or coloured Red For continued protection against risk of fire replace only with same type and rating of fuse ASTA approved 5A 250VAC fuse CAUTION TO PREVENT ELECTRIC
15. 3 To configure your wireless settings please refer to Network settings section in this manual English 17 Broadband ISP Connection USB Inputs Side of the TV iA n j Adaptor e A Wireless N router IEEE 802 11a b g n with simultaneous 2 4 and 5 GHz bands is designed to increase bandwidth These are optimized for smoother and faster HD video streaming file transfers and wireless gaming Use a LAN connection for quicker file sharing between other devices like computers The frequency and channel differ depending on the area The transmission speed differs depending on the distance and number of obstructions between the transmission products the configuration of these products the radio wave conditions the line traffic and the products that you use The transmission may also be cut off or may get disconnected depending on the radio wave conditions DECT phones or any other WiFi 11b appliances The standard values of the transmission speed are the theoretical maximum values for the wireless standards They are not the actual speeds of data transmission The location where the transmission is most effective differs depending on the usage environment The Wireless LAN adaptor should be connected directly to the TV s USB port USB hubs are not supported To configure wireless settings please refer to the WiFi section in the Settings menu You can plug your wifi dongle into the supplied US
16. Afterwards engage your cell phone with the router and then activate the sharing software on your cell phone Then select files that you would like to share with your TV e If the connection is established correctly you should now be able to access the shared files from your cell phone via the Media Browser of your TV e Enter the Media Browser menu and the playback device selection OSD will be displayed Select your mobile phone and press the OK button to continue Note This feature may not be supported on all mobile phones Connectivity Troubleshooting Wireless Network Not Available Ensure that any firewalls of your network allow the TV wireless connection e Ensure the USB WiFi dongle Supplied is plugged in fully If the wireless network does not function properly try using the wired network in your home Refer to the Wired Connection section for more information on the process If the TV does not function using the wired connection check the modem router If the router does not have a problem check the internet connection of your modem Try searching for wireless networks again using the Network Settings menu screen Connection is slow See the instruction book of your wireless modem to get information on the internal service area connection speed signal quality and other settings You need to have a high speed connection for your modem Distruption during playback or slow reactions You co
17. B extension cable In cases where network quality is poor and the wifi dongle needs to be placed to a location with better signal quality Wireless LAN adaptor supports 802 11 a b g amp n type modems It is highly recommended that you should use the IEEE 802 11n communication protocol in order to avoid any possible problems while watching videos e Use the other USB input if you experience problems with audio video performance e You must change your modem s SSID when there are any other modems around with the same SSID You can encounter connection problems otherwise Use a wired connection if you experience problems with a wireless connection Network Settings Network Type Canfiguration Status Not Connected IP Address Network Name To enable Wi Fi features plug in the Wi Fi dongle to one of the USB ports Press the YELLOW button to scan the wireless networks from the network settings menu A list of available networks will be displayed Please select your desired network from the list If the selected network is protected with a password please enter the correct key by using the virtual keyboard You can use this keyboard via the navigation buttons or Da AN or NZ and the OK button on the remote control Enter Password b l V 1 4 Delete AB ab Space Wait until the IP address is shown on the screen Press the GREEN button to switch to advanced mode and then press the OK butto
18. D Players PVR video games etc e Teletext e Headphone connection Manual tuning e Automatic power down after up to six hours e Sleep timer e Child lock e Automatic sound mute when no transmission e NTSC playback e AVL Automatic Volume Limiting e PC input e Plug amp Play for Windows 98 ME 2000 XP Vista Windows 7 e Game Mode optional e Ethernet LAN for Internet connectivity e 802 11n WiFi Support via USB dongle e DLNA English Viewing the TV a Menu Access Press the MENU button on your remote control to display the main menu screen Use the or 2 buttons to select a menu tab and press the OK button to select option Use the Or or AN or Ne buttons to select or set an item Press BACK or EXIT or MENU button to quit a menu screen Input Selection Once you have connected external systems to your TV you can switch to different input sources Press ac the f source button on your remote control consecutively to select the different inputs oe TV Control button amp Operation The Control button allows you to control the Volume Programme Source and Standby On functions of the TV To change volume Increase the volume by pushing the button up Decrease the volume by pushing the button down T
19. ED OFF In order to watch certain digital channels a conditional access module CAM can be necessary This module must be inserted in the Cl slot of your TV 1 Obtain the Conditional Access Module CAM and the viewing card by subscribing to a pay channel company then insert those to the TV using the following procedure 2 Insert the CAM and then the viewing card to the slot that is located in the terminal cover at the rear side of the TV 3 The CAM should be correctly inserted it is impossible to insert fully if reversed The CAM or the TV terminal may be damaged if the CAM is forcefully inserted 4 Connect the TV to the mains supply switch on and then wait for few moments until the card is activated 5 When no module is inserted No Common Interface module detected message appears on the screen You can refer to the module instruction manual for details of the settings re z 5 English Standby Notifications If the TV does not receive any input signal e g from an aerial or HDMI source for 5 minutes the TV will go into standby When you next switch on the following message will be displayed Standby Cause No Signal Press OK to continue When the Auto Tv Off timeout is reached the following message will be displayed on the screen Select YES to shut down the TV Select NO to cancel The TV will switch off as well if you do not make a selection on this screen
20. FINLUX 32 inch LED TV 32F8072 T Owner s manual HIGH DEFINITION MULTIMEDIA INTERFACE GZ8ZSC0S Contents Safety Precautions o cccieccscssasssucnsssnandsacenessenssancnonnnas 2 PRG DAO ceettenepenesteueceacurecesetceserueeteapstuseteeseceaes 2 intended SC isccccsensesincnneesdnnsentestecantagerecnceetnadoreas 2 OWE SOUNCE ssnsd ein nna E 2 Positioning the TV cs ceraativicsdersduunmpacuiaietcdtaseovens 2 Power cord and DUG iscnaassccinssersurneasscuiaiaouainanerens 2 Moisture and Water cccccscccsseeeceeeeseeseeseeees 3 VOMA seansini 3 Heat sources and Flames ccccccceeseeeeeeeeees 3 Headphone Volume cccccccccseseeceeeeceeseesseaes 3 Wall Mounting optional sicicinssneententseeddnanwaneddecess 3 Uh st cade ose eect cued snes TA A TTE 3 i rna 3 Environmental Information c cccccceeeeeeeeeeees 3 Accessories INCIUGG cccccccsssseeeceeeeseesseseeeees 3 TY CANES cenana Aa 4 Viewing the TV weccitincrcsbitsudiedareinaiinntiidwcietwxanthininwsbits 4 TV Control button amp Operation cccccecceseeeeees 5 Remote Control ses gerccereccneaieertnectnctecerenatenseeniereceictis 6 Using a Conditional Access Module 00 8 Standby NOM CAVONS i lt 0ccciccascvancsainnsseesaccaaesaeceanedencis 8 Inserting the Batteries to the Remote 9 Connect Power amp Antenna c cceccceseeeeeeeeeeeees 9 SL Co all gis 9 Ren
21. K button Then select Delete Timer option The timer will be cancelled Note It is not possible to record two channels at the same time Recording a Programme IMPORTANT When using a new USB hard disk drive it is recommended that you first format the disk using your TV s Format Disk option To record a programme you should first connect a USB disk to your TV while the TV is switched off You should then switch on the TV to enable the recording feature To use the recording function you need to connect a USB disk or an external hard disk drive to the TV and the connected USB disk should have at least 1 GB capacity and should have 2 0 speed compatibility If the connected USB device does not support 2 0 speed an error message will be displayed Note Recorded programmes are saved into the connected USB disk If desired you can store copy recordings onto a computer however these files will not be available to be played on a computer You can play the recordings only via your TV Note Lip Sync delay may occur during the timeshifting Radio record is not supported The TV can record programmes up to ten hours Recorded programmes are split into 4GB partitions If the writing speed of the connected USB disk is not sufficient the recording may fail and the timeshifting feaute may not be available Recordings of HD programmes can occupy more space on the USB disk compared to SD programmes For this reason it i
22. Next button Nero MediaHome 4 E ials Installation Prerequisites In order for the selected applications to function properly the following third party software must be installed first Click the Install button to start the installation Nero Ask Toolbar ante aS a Product Patcher W 9 Click the Next button e The Ready to Start Installation Process screen is displayed installation begins and finishes automatically A progress bar informs you of the progress of the installation process 26 Nero MediaHome 4 Essentials Inst Nero MediaHome 4 Essentials is Being Installed Die meistverkaufte Multimediasuite ist jetzt dank herausragender HD Funktionen noch leistungsf higer Nero Multimedia Suite 10 Platinum HD gibt kreativen Enthusiasten in einer umfassenden Suite alles an die Hand was sie zum professionellen Bearbeiten von HD Videos Brennen Sichern Wiedergeben von Blu ray Discs und vielem mehr ben tigen Die Suite umfasst alle Funktionen der Nero Multimedia Suite 10 und dar ber hinaus Platinum Funktionen wie die Wi abe von Blu ray Discs Transfers zwischen tragbaren Ger ten das Nero Creative CollectionPack und Nero Online Backup 1 Jahr lang kostenlos Weitere Informationen finden ie auf www nero com 10 Installation finishes The Help us to Enhance Nero Software screen is displayed In order to offer a better service Nero is collecting anonymous data to determine which features are used a
23. OK Media Browser English 19 If sharing configurations are set properly the following OSD message will be displayed after selecting the desired media type Select OK to display the selected network or USB memory content If you want to refresh the device list press the GREEN button You can press MENU to exit Device Selection iptvsrvO2 TVersity Media Serve Nero MediaHome 4 IPTVSRV IPTVSRV TVersity Media Server mw Refresh OK Select MENU ESN f available networks are found they will be listed on this screen Select media server or network that you want to connect to using the AX or Nr buttons and press OK If you select the media type as Video and choose a device from the selection menu a new menu screen will appear on the screen as below Media Browser Buz_Devri_3 2009 TURKCE Videos File Name ra Ey T B sort By Name 1 1 lt usb1 Root List ag Change Media 0 9 DM OK Play This gt Te fz Toggle View Style LANG eon I J Loop Shuffle Select Videos from this screen to list all the available video files from the selected network To play other media types from this screen you must go back to main Media Browser screen and select the media type as desired and then perform the network selection again Refer to the Media Browser USB Playback section for further information on file playback Subtitle files do not work if you watch videos from your netwo
24. SHOCK DISCONNECT FROM THE MAINS BEFORE REMOVING COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL SAFETY PRECAUTION THIS EQUIPMENT MUST BE DISCONNECTED FROM THE MAINS WHEN NOT IN USE DO NOT ALLOW THIS UNIT TO BE EXPOSED TO RAIN OR MOISTURE English 36 Al Product Fiche E Comercial Brand FINLUX Product No 10086706 Model No 32F8072 T Energy efficiency class A Visible screen size diagonal approx inch cm On mode average power consumption Watt Annual energy consumption kWh annum Standby power consumption Watt Off mode power consumption Watt 32 inches 41 59 0 5 0 Display resolution px 1920 x 1080 English 3 7 Thank you for your purchase We are sure you will enj for many years The product warranty is for a period of twelve 12 months from the date of original purchase Any defect caused by faulty materials or workmanship will be repaired free of charge where possible during this period by Finlux If a repair is not possible the product will be replaced free of charge or a refund will be given This guarantee is subject to the following provisions The guarantee does not cover accidental damage misuse cabinet parts knobs or consumable items e The product must be correctly installed and operated in accordance with the instructions in the manual provided e The product must be us
25. The Quick Settings menu allows you to access some options quickly This menu includes Power Save Mode Picture Mode Equalizer Settings Favourites and Sleep Timer FollowMe TV and Information booklet options Press Q MENU button on the remote control to view quick menu See the following chapters for the details of the listed features Settings Power Save Mode Picture Mode Dynamic Equalizer Settings User Favourites off Sleep Timer Off FollowMe TV Ok Information booklet Ok met Navigate ange awe GZ Exit J E pitis FollowMe TV optional With your tablet you can stream the current broadcast from your smart TV using the FollowMe TV feature Install the appropriate application to your tablet PC Start the application For further information on using this feature refer to the instructions of the application you use E Manual optional You can find instructions for your TV s features in the E Manual To use E Manual press to the Info button while main menu is displayed on the screen By using the navigation buttons select a desired category Every category includes a different topics Select a topic and press OK to read instructions To close the E Manual screen press the Exit button Note The contents of the E Manual may vary according to model English 11 Menu Features and Functions Picture Menu Contents You can change the picture mode to suit your preference or requirements The P
26. a HDMI source this feature will be visible in the Picture Settings Black menu You can use this feature to enhance the blackness in the picture Film Mode Films are recorded at a different number of frames per second to normal television programmes Tum this feature on when you are watching films to see the fast motion scenes clearly Skin Tone Adjust the desired skin tone Colour Shift Adjust the desired colour tone RGB Gain Press OK button to edit RGB gain You can configure the colour temperature values using the RGB Gain feature Auto Position Automatically optimizes the display Press OK to optimize in PC mode ki roSitnonn This item shifts the image horizontally to the right hand side or left hand side of the screen PC mode V Position in This item shifts the image vertically towards the top or bottom of the screen PC mode Dot Clock in Dot Clock adjustments correct the interference that appear as vertical banding in dot intensive PC mode presentations like spreadsheets or paragraphs or text in smaller fonts Depending on the resolution and scan frequency that you input to the TV set you may Phase in PC l l o mode see a hazy or noisy picture on the screen In such a case you can use this item to get a clear picture by using trial and error Reset Resets the picture settings to factory default While in VGA PC mode some items in Picture menu will be unavailable Instead VGA mode settings w
27. and click START SERVER Nero MediaHome 4 Essentials Shares Media Library Local Folders Online Services Apple R iTunes Select Folders to be shared Options Share Status C Documents and Settings aylinac Belgelerim Resimler Network Devices Transcoding RemoteUI Y By sharing your files over the network you enable everybody throughout the LAN local area network to browse and download your shared media files Please take care not to share any private or confidential files CO 2 Fe g Q Start Server 15 You can display all media types from the library Click Refresh icon to refresh Click STOP SERVER icon to stop server Nero MediaHome 4 Essentials iB Shares Media Library Local Folders Online Services Apple R iTunes Browse media which is already indexed gs Options a Network L Devices P a Transcoding q RemoteUI w TY g Status Nero MediaHome H O All Media H G Music E O Photos H O Videos Collections By sharing your files over the network you enable everybody throughout the LAN local area network to browse and download your shared media files Please take care not to share any private or confidential files m Stop Server English 25 Internet Browser To use the internet browser please select the internet browser logo from the portal section Refresh Home
28. ations have been made To operate your TV in extreme ambient conditions may cause damage of the device English A WARNING Never let people including children with reduced physical sensory or mental abilities or lack of experience and or knowledge use electrical devices unsupervised Children may not recognize dangers of incorrect use The swallowing of batteries can be fatal Keep batteries always out of reach of small children If a battery is swallowed immediately seek medical attention Keep the packaging films out of reach of children to prevent the risk of suffocation Power source e The TV should be operated only from a 220 240 V AC 50 Hz outlet A Warning Do not leave your TV in standby or operating mode when you leave your house Positioning the TV e For ventilation please leave a clear space of at least 10cm all around the TV e Do not block the ventilation openings e Do not place the TV on sloping or unstable surfaces the TV may tip over e To prevent damage to the TV do not place any objects on top of the TV e Only use the TV in moderate climates Power cord and plug e The power cord plug should be easily accessible If there is lightning or storms or if the TV is not going to be used for a while e g if going away on holiday disconnect the TV set from the mains e The mains plug is used to disconnect TV set from the mains and therefore it must remain readily operable e Do no
29. ays has the most up to date firmware Please ensure that the TV is set to standby mode with an aerial connected to pick up the over air download Application Version Displays application version Hard of Hearing Enables any special feature sent from the broadcaster Audio Description Audio description refers to an additional narration track for blind and visually impaired viewers of visual media including television and movies You can use this feature only if the broadcaster supports the additional narration track Auto TV Off You can set the timeout value of the auto off feature After the timeout value is reached and the TV has not been operated for a selected time the TV will go into standby mode Standby Search optional If you change Standby Search to Off this function will be unavailable To use Standby search please make sure that you select Standby Search as On If the Standby Search is set to On when the TV is in standby mode available broadcasts will be searched If the TV locates any new or missing broadcasts a menu screen will be displayed asking you whether or not to execute these changes The Channel list will be updated and changed after this process Please activate the Standby Search setting in order to enable your TV to automatically update the broadcast frequency of the broadcaster broadcast definition and other similar changes Store Mode Optional If you are displaying the TV in
30. ear on the screen Index Resolution Frequency 1400x1050 75Hz 1 640x400 1400x1050 85Hz 640x350 1440x900 640x400 1440x800 640x480 1600x1200 40x4 sabe sonz 1680x1050 60Hz 640x480 1920x1080 60Hz 1920x1200 1152x864 60Hz English 32 Appendix C Supported File Formats for USB Media Browser Movie dat mpg mpeg dat mpg mpeg mp4 mov flv 3gp 3g2 asf wmv mp3 wav WMA ASF m4a aac png bmp png sub srt Mpeg1 2 MPEG1 2 Layer 1 2 3 AAC HEAAC AC3 EAC3 LPCM ADPCM MPEG1 2 Layer 1 2 3 AAC HEAAC AC3 EAC3 LPCM ADPCM MPEG2 H 264 VC1 AVS MVC MPEG2 MPEG1 2 Layer 1 2 3 AC3 LPCM MPEG1 2 4 XviD H 264 VC1 WMV3 Motion JPEG MPEG1 2 Layer 1 2 3 AAC HEAAC AC3 EAC3 LPCM MPEG1 2 Layer 3 AAC HEAAC AC3 EAC3 LPCM ADPCM MPEG1 2 4 Xvid H 264 VC1 WMV3 Sorenson H 263 Motion JPEG H 264 Sorenson H 263 MPEG1 2 Layer 1 2 3 AAC HEAAC AC3 EAC3 LPCM ADPCM WMA MPEG1 2 Layer 3 AAC HEAAC LPCM ADPCM MPEG4 H 264 MPEG2 4 XviD H 264 VC1 WMV3 English 33 Ee ee 1080P 30fps 50Mbit sec H 264 1080Px2 25fps 1080P 50fps MVC 1080P 24 fps Other 1080P 30fps 50Mbit 1080P 30fps 50Mbit sec H 264 1080Px2 25fps 1080P 50fps Other 1080P 30fps 5OMbit sec H 264 1080Px2 25fps 1080P 50fps Other 1080P 30fps 50Mbit sec H 264 1080Px2 25fps 1080P 50fps Other 1080P 30fps 50Mbit sec H 264 1080Px2 25fps 1
31. ected function Note that if you perform first time installation MY BUTTON 1 will return to its default function Using My Button 2 Press MY BUTTON 2 for five seconds when on a desired source channel or link until the MY BUTTON IS SET message is displayed on the screen This confirms that the selected MY BUTTON is now associated with the selected function 262 Viewing the Connections Scart Se nea Connection back VGA Q Connection back SIDE AV W A j SIl PC YPbPr i i Audio Connection i Side Audio Video side Connection Cable PC Audio Cable Supplied Not supplied HDMI Connection ie i back SPDIF Connection back SPDIF SIDE A D Le Side AV 7 i a Connection mS side AV Connection Cable supplied HEADPHONE Headphone Connection O side HEADPHONE YPbPr Video Connection side YPbPr Connection Cable Not supplied USB Connection EE side CI Connection K K 4 side COMMON INTERFACE
32. ed solely for domestic purposes e The guarantee will be invalid if the product is re sold or has been damaged by inexpert repair Specifications are subject to change without notice On site service is limited to Vestel 46 Televisions and above Repairs Our authorised service partners will always try to complete any repairs at your home However there may be times when the product has to be taken away for further testing If this happens you will not be charged for collection or return of the product within the terms of this guarantee Disclaimer The manufacturer disclaims any liability for incidental or consequential damages This guarantee is in addition to and does not diminish your statutory or legal rights Customer helpline In the event of a problem with the product within the guarantee period please call this number Customer Helpline 0845 459 52 82 Warranty Exclusions A This Warranty does not extend to loss caused by normal wear and tear fire water liquid ingression theft vermin or insect infestation B This warranty does not cover damage caused by e Misuse or abusive use of any Finlux consumer product e Incorrect operation or not following the operating instructions as stated in the Product Instruction Manual e Improper installation e Failure to clean or improper cleaning of the product e Incorrect voltage or non authorised electrical connections e Use of non aut
33. emneenretnen tt here onenee rere tenner foment 9 T Switch the TY ON iescjeicc A ereartersseecacy a seousceetes 9 Wo Switch the TY Off escarnirs 9 First Time INS tAllAV ON geucedsceccdiem ceesarsesinaddactsstenoseiens 9 Media Playback via USB Input ccceeeeeeees 10 Media Browser Menu cccssseessseeeeeeeesees 10 Changing Image Size Picture Formats 11 Using the Channel List vs cicnscccsassanescetcsanatacdepeasaderes 11 ITS IVS ALY sso icores wa uctastncatinc yatestloa iasausaatestoraasanlniia niente 11 Menu Features and Functions ccccceeeeeens 12 Menu Features and Functions ccccsseeeeees 13 Menu Features and Functions ccccceeeeens 14 Electronic Programme Guide EPG 06 15 Programme ODUON Ss sciacicincssd wnteracdsnimencdneesnceents 15 Recording a Programme ccssccccssseeeesseeeeeees 15 Timeshift Recording accaccccccssncssiecawacneccaccasescentannees 16 FISTS Recording soirs 16 Watching Recorded Programmes 00008 16 Recordings LIDIAlY sincicicciaccnvutieriuoacticcassvinulnanaaten 16 Recording Configuration cccccssssseeeessssseeeees 16 Wired COnNMECUVILY i sivceisnssssotenscnsaadmennatecedgasanenccees 16 To Connect to a Wired Network 00008 16 Configuring Wired Device Settings 17 Configuration Status ccccccceeeeesseeeeeeeeeeaes 17 IP AdArESS f
34. er Save Mode Power Save Mode If Picture Off is selected Screen will be off in 15 seconds message will be displayed on the screen Select PROCEED and press OK to continue The screen will be off in 15 seconds If you disable Power Save Mode Picture mode will be automatically set to Dynamic When the TV is not in use please switch off or disconnect the TV from the mains plug This will also reduce energy consumption Disconnect power when going away for longer time It is highly recommended that you activate the Power Save Mode setting to reduce your annual power consumption And also it is recommended to disconnect the TV from the mains plug to save energy more when you do not use Please helps us to save environment by following these steps Repair Information Please refer all servicing to qualified personnel Only qualified personnel must repair the TV Please contact your local dealer where you have purchased this TV for further information Accessories included Remote Control Batteries 2 x AAA Instruction Book Side AV Connection Cable Nero Media Home CD Wi fi USB dongle USB Cable English 3 TV Features Remote controlled colour LED TV e Fully integrated digital tuner e HDMI Inputs are for connecting a device that has a HDMI socket e USB input e Programme recording e Programme timeshifting e 1000 programmes e OSD menu system e Scart socket for external devices such as DV
35. eric buttons Channel List TV source Menu Volume up down Back button Favourite channel list Image size My button 1 My button 2 Teletext Electronic programme guide Mute Info Exit return Ok confirm Programme up down Navigational buttons Q menu Channel swap Blue button Yellow button Subtitle on off Rapid advance Stop Pause in media browser mode Timeshift recording Multimedia browser Picture mode selection Standby button Function LED English SOURCE 6 LANG lt lt a b gt B T i 8 9 1 JI 2 xs Dui D AIR Tears 1Sa Dooz A 24 15 CBACK BEID 23 oW 16 fart Po lt 4 a a7 x6 R E 20 18 49 Using My button 1 This button s main function is to run Youtube link However if you want to change this function you can press MY BUTTON 1 for five seconds when on a desired source channel or link until the MY BUTTON IS SET message is displayed on the screen This confirms that the selected MY BUTTON is now associated with the sel
36. ers tosent cacecnesascnasennen Arsadensnenasseoensance 17 Configuring Wired Network Settings in Advanced POS ETETE A E T T T 17 Wireless Connectivity c cccsscccessessseeeeeeseneees 17 Connecting to a Wireless Network 17 Other Information c ccccccceseeceeeeseeeeseeeeeeeeaees 19 Delete Saved WiFi Profiles cccccccceeee 19 Connecting to your mobile Phone via WIiFi 19 Connectivity Troubleshooting ccccsseeeeeeeeees 19 Connection iS SIOW ccccceccceceeeeeeseeeeeeeeeeeees 19 Distruption during playback or slow reactions 19 Using DLNA Network Service 0 0000 19 1 Nero Media Home Installation 19 2 Connect to a Wired or Wireless Network 19 3 Play Shared Files via Media Browser 19 LIN EEEE T T T 19 Internet Portal aannaannnennnnannaennnenennneeonnnnenrnenene 20 Digital Teletext ess satedesidenaisneincdidiconisataversadinedstrean 20 Software UD OPACE cscs scsacssccassacvesstcsideaedectesvanseteats 21 Troubleshooting amp TipS ccccccccessessseeeeeeeeneees 21 NO DOWOD o apresen iia ea Er i a 21 NO DICU essa a Rn er enon eee 21 KO SOU a E E 21 Remote control does not operate 21 Recording Unavailable cccccceseeseeeeeees 21 USB IS 100 SIOW saena e 21 Internet Connection Not Available DLNA Mode Not Opera eeano asa E eee 21 invalid DOMAN
37. h the active connection to the TV set Select this as Wired if you are connecting via an ethernet Network Settings Network Type Not Connected Configuration Status IP Address Configuration Status This section displays the status of the connection Select Connected if you want to activate a connection Select as Not Connected to end an active connection IP Address If an active connection is available the IP address will be displayed on this section If you want to configure an IP address preference press the GREEN button and switch to the advanced mode Configuring Wired Network Settings in Advanced Mode After pressing the GREEN button the Advanced mode will be available While in Advanced Mode press the RED button to edit settings When finished press OK to save Press RETURN BACK to cancel Wireless Connectivity Connecting to a Wireless Network IMPORTANT USB dongle Supplied is required to use wireless network features e To use your TV with your wireless network you need a Wireless USB dongle To make your modem s SSID visible you should change your SSID settings via the modem s software The TV cannot connect to the networks with a hidden SSID To Connect to a wireless LAN you should perform the following steps 1 Ensure that Nero Media Home software is installed to your PC for DLNA function 2 Then connect the wireless adaptor to one of the USB inputs of the TV
38. horised non standard parts e Password setting resetting and virus infection e Repair or other work carried out on the Finlux consumer product other than by authorised Finlux service personnel C This Warranty does not cover service costs for the replacement and maintenance of consumable parts which have stopped working through normal wear and tear This includes but is not limited to parts classifiable as a consumable part Guarantor Vestel UK Ltd 16 Hanover Square London W1S 1HT Tel 0845 459 52 82 D This Warranty does not cover any Finlux branded consumer product installed in a moveable dwelling Note that the performance of the product may be affected if it is installed in a caravan or other such moveable dwelling E This Warranty does not cover Finlux consumer products which do not bear the original manufacturer s factory applied serial number in its original form for instance where it or the sticker bearing it has been removed wiped out rubbed off or altered This applies even if you make a claim while the product is still under Warranty F This Warranty does not cover the loss of any data no matter how the loss is caused You are responsible for backing up and protecting data against loss damage or destruction The guarantee is only valid when accompanied by proof of purchase If the serial number is defaced missing or illegible the warranty is null and void FINLUX
39. ic heater e Ensure that no open flame sources such as lit candles are placed on top of the TV Headphone Volume e Excessive sound pressure from earphones and headphones can cause hearing loss please take care Wall Mounting optional e To prevent injury this TV must be securely attached to the wall in accordance with the installation instructions if the option is available Screen e Occasionally a few non active pixels may appear on the screen as a fixed blue green or red point Please note that this does not affect the performance of your product e Take care not to scratch the screen with fingernails or other hard objects Cleaning e Before cleaning unplug the TV from the wall socket e Do not use liquid or aerosol cleaners Only use a soft dry cloth Environmental Information This television is designed to consume less energy to help save environment You can not only help to save the environment but you can also save money by reducing your electricity bills thanks to the energy efficiency feauture of this TV To reduce energy consumption you should take the following steps You can use the Power Save Mode setting located in the Picture Settings menu If you set the Power Save Mode as Eco the TV will switch to energy saving mode and the luminance level of TV set will be decreased to the optimum level Note that some picture settings will be unavailable to be changed when the TV is in Pow
40. icture Mode mode can be set to one of these options Cinema Game Sports Dynamic and Natural Contrast Sets the lightness and darkness values of the screen Brightness Sets the brightness value for the screen Sharpness Sets the sharpness value for the objects displayed on the screen Colour Sets the colour value adjusting the colors Power Save Mode To set the Power Save Mode as Eco Picture Off or Disabled See the section Environmental Information in this manual for further information on the Power Save Mode This setting controls the backlight level and it can be set to Auto Low Medium Backlight High The Backlight function will be inactive if the Power Save Mode is set to On The optional Backlight cannot be activated in VGA Media Browser mode or while the picture mode is set to Game Noise If the broadcast signal is weak and the picture is noisy use the Noise Reduction setting to reduce the Reduction amount of noise Noise Reduction can be set to one of these options Low Medium High or Off Advanced Settings Dynamic You can change the contrast rate by using the dynamic contrast function Dynamic contrast Contrast can be set to one of these options Low Medium High or Off Colour Temp Sets the desired colour tone Normal Warm or Cool Picture Zoom Sets the picture size to Auto 16 9 Subtitle 14 9 14 9 Zoom 4 3 or Cinema HDMI True While watching from
41. ill be added to the Picture Settings while in PC mode English 12 Menu Features and Functions Sound Menu Contents Volume Adjusts the volume level In the equalizer menu the preset can be changed to Music Movie Speech Flat Equalizer Classic and User Press the MENU button to return to the previous menu Equalizer menu settings can be changed manually only when the Equalizer Mode is in User Balance This setting is used for emphasizing left or right speaker balance Headphone Lineout When you connect an external amplifier to your TV using the headphone jack you can select this option as Lineout If you have connected headphones to the TV set this option as Headphone You can select Mono Stereo Dual or Dual Il mode only if the selected channel DUNE SUE supports that mode Automatic Volume Limiting AVL function sets the sound to obtain a fixed output AVL level between programmes For instance volume level of advertisements tend to be louder than programmes Dynamic Bass Enables or disables the Dynamic Bass Surround Sound Optional Surround sound mode can be changed as On or Off Digital Out Sets digital audio output type Install and Retune Menu Contents Automatic Channel Scan Retune Digital Aerial Searches and stores aerial DVB stations eal A git apa This feature can be used for direct broadcast entry Deletes all stored cha
42. imeline Schedule EPG BLUE Displays filtering options RECORD The TV will start to record the selected progamme You can press again to stop the recording IMPORTANT To record a programme you should first connect a USB disk to your TV while the TV is switched off You should then switch on the TV to enable the recording feature Otherwise the recording feature will not be available Note Switching to a different broadcast or source is not available during a recording Programme Options In the EPG menu press the OK button to enter the Event Options menu Select Channel In the EPG menu using this option you can switch to the selected channel Record Delete Record Timer After you have selected a programme in the EPG menu press the OK button and and the Options screen will be displayed Select the Record option and press the OK button After this operation a recording will be scheduled for the selected programme To cancel an already set recording highlight that programme and press the OK button and select the option Delete Rec Timer The recording will be cancelled Set Timer Delete Timer After you have selected a programme in the EPG menu press the OK button and and the Options screen will be displayed Select the Set Timer on Event option and press the OK button You can set a timer for future programmes To cancel an already set timer highlight that programme and press the O
43. isplayed with available recordings All the recordings are kept in a list in the recordings library RED button Delete Erases the selected recording GREEN button Edit Makes changes on the selected recording BLUE button Sort Changes the order of the recordings You can select from a wide range of sorting options OK button Resume Resume playback INFO Details Displays the programme information details Recording Configuration Select the Recording Configuration item in the Settings menu to configure the recording settings Format Disk You can use the Format Disk feature for formatting the connected USB disk IMPORTANT Note that ALL the data stored on the USB disk will be lost and the disk format will be converted to FAT32 if you activate this feature If your USB disk malfunctions you can try formatting the USB disk In most cases formatting the USB disk will restore normal operation however ALL the data stored on the USB disk will be lost in such a case Note f USB is too slow message is displayed on the screen while starting a recording try restarting the recording If you still get the same error it is possible that your USB disk does not meet the speed requirements Try connecting another USB disk Wired Connectivity To Connect to a Wired Network For connecting to a wired LAN you should perform the following steps e You must have a modem router connected to an active broadband con
44. license agreement carefully and select the appropriate check box if you agree to the terms of the agreement Installation is not possible without this agreement English 23 6 Click the Next button e The Select Installation Type screen is displayed It is possible to choose between Typical meaning standard installation or Custom installation User defined installation allows you to determine languages to be installed and to choose the installation path Nero MediaHome 4 Essentials Installation Select Installation Type Please select an installation type Typical pris The standard installation will be executed z 4 Custom old Select the Nero applications to be installed their location and the Jr languages Only recommended for experienced users ETEB m B 7 Use Typical installation and click the Next button e The Prerequisites screen is displayed The Nero MediaHome installation wizard checks the availability of required third party software on your PC If applications are missing they are listed and must be installed before continuing installation Nero MediaHome 4 Essentials Installation Prerequisites In order for the selected applications to function properly the folowing third party software must be installed first Click the Install button to start the installation ra 8 Click the Install button e As soon as all prerequisites are installed the Install button will change to a
45. logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC HIGH DEFINITION MULTIMEDIA INTERFACE English 22 Appendix Nero MediaHome Installation This software is compatible with Windows XP and Windows 7 To install Nero MediaHome please proceed as follows Note To use DLNA function this software should be installed to your PC 1 Insert the Nero MediaHome installation disc in your optical disc drive e The Nero Multilnstaller screen with a button to start the installation process will open automatically e If below window is not displayed automatically double click on the file SetupX located on the Nero MediaHome installation disc P i Nero Multilnstaller MediaHome 4 Essentials Nero MediaHome 4 Essentials 2 Click on the button labeled Nero MediaHome Essentials to start the installation process e The Nero MediaHome installation wizard is displayed e Ifnecessary change installation language from the language selection menu before continuing Nero MediaHome 4 Essentials Installation DHR Welcome to the Installation of Nero MediaHome 4 Essentials nero MediaHome 4 This wizard will guide you through the installation process for Nero MediaHome 4 Essentials Just click Next to go through the installation steps Warning This software is protected by international copyright laws Engish Use this language for
46. n to edit settings This means that the connection is now established To disconnect from a wireless network you should highlight Configuration Status and press OK Network Settings Network Type Configuration Status Connected IP Address 192 168 1 100 Network Name emre E Back By Advanced A Enable Disable E Delete Saved Wifi Profile BF Internet Speed Test E Scan Wireless Networks English 18 You can navigate between menu tabs by pressing left right buttons The help bar on the bottom of the dialog shows features that you may use Press the BLUE button to check your internet connection speed You can check the signal strength by using the network settings menu for the wireless device mode Other Information Configuration Status Displays Wi Fi status as connected or not connected IP Address Displays the current IP address Network Name Connected networks name will be displayed Delete Saved WiFi Profiles Saved profiles will be deleted if you press the Red button while the wireless device selection OSD is on the screen Connecting to your mobile Phone via WiFi If your mobile phone has WiFi feature you can connect your mobile phone to your TV by using a WiFi connection via a router in order to play content from your phone For this your cell phone must have appropriate sharing software e Connect to your router following the steps stated above in the Wireless Connection section e
47. nd what problems if any occur Nero MediaHome 4 Essentials Installation In order to offer better service Nero is collecting anonymous data to determine which features are used and what problems if any may occur If you would like to participate in this anonymous data collection now simply click on the fol E Yes I want to help by sending anonymous application data to Nero You can also join at a later time by opening the Nero ControlCenter and clicking on Product Settings Privacy Statement Nero does not collect any personal info guards your privacy please read our pri tion that can be used to contact the individual user For more details about how Nero statement English 24 11 If you would like to help by participating in the anonymous collection of usage data select the check box and click the Next button e The final screen of the installation wizard is displayed 12 Click the Exit button Nero MediaHome 4 Essentials Installation Installation Successful nero MediaHome 4 The installation wizard has successfully installed ial Nero MediaHome 4 Essentials 13 Ashortcut called Nero MediaHome 4 is now placed on your desktop Congratulations You successfully installed Nero MediaHome 4 on your PC 14 Run Nero MediaHome by pressing shortcut icon e Click ADD icon from LOCAL FOLDERS to add the folder you want to share with the network Select the folder that you want to share
48. nection e Ensure that Nero Media Home software is installed to your PC for DLNA function See Appendix G for more information on the installation process e Connect your PC to your modem router This can be a wired or wireless connection e Connect your TV to your modem router via an ethernet cable There is a LAN port at the rear back of your TV English 16 Broadband ISP Connection _ ewe DL LLL us w F Lan Ethernet cable ips ae TV e To access and play shared files you must select the Media Browser Press the Menu button and select Media Browser by using the KK or Y buttons and press OK to continue Select the desired file type and press OK You must always use the Media Browser screen to access and play shared network files e PC HDD Media Player or any other devices that are DLNA 1 5 compatible should be used with a wired connection for higher playback quality To configure wired settings please refer to the Network Settings section in the Settings menu e You might be able to connect your TV to your LAN depending on your network s configuration In such a case use an ethernet cable to connect your TV directly to the network wall outlet The modem port on the wall 1 G a sae Rear of TV Configuring Wired Device Settings The Network type can be selected as Wired or Wireless in accordance wit
49. nnels and settings resets TV to factory settings and starts First Time Sees amp i mecilation first time installation You can follow the instructions in the First Time Installations section for more information on this process English 13 Menu Features and Functions Settings Menu Contents Conditional Access Controls conditional access modules when available Language Configures language settings Enter correct password to change parental settings You can easily adjust child lock and Parental set new pin number in this menu Once the child lock is activated open browser app on the portal will be disabled it can be enabled again by deactivating the child lock Timers Sets timers for selected programmes USB Record Aeolian Displays the recording configuration menu USB Record Date Time Sets date and time Sources Enables or disables selected source options Network Settings Displays network settings Other Settings Displays other setting options of the TV set Menu Timeout Scan Encrypted Changes timeout duration for menu screens When this setting is on the search process will locate encrypted channels as well If itis setas Off encrypted channels will not be located in automatic or manual searches Blue Background Activates or deactivates the blue background system when the signal is weak or absent Software Upgrade To ensure that your TV alw
50. nt to scan coded stations First time installation Welcome Country Norway Search Type Digital only Teletext Language Turk Gre Scan Encrypted Channels Yes MEM Select Setting KEJ Choose your country Ok Start search Press OK button on the remote control to continue and the following message will be displayed on the screen If the TV is to be used in a store please select the Store Mode For domestic use Home Mode is recommended Store Mode You can activate Store mode option by using lt or j button If Store Mode is selected Store mode option will be available in other settings menu and your TV s features will be illustrated on the top of the screen A confirmation English 9 screen will be displayed after selecting the Store Mode Select YES to proceed Store Mode Selected Are You Sure If Home Mode is selected Store mode will not be available after the First Time Installation Press OK button on the remote control to continue and the following message will be displayed on the screen Do you want to start an automatic channel scan i Select Yes and the television will search for digital terrestrial TV broadcasts d Automatic channel scan Retune Please wait This will take a few minutes Scanning digital channels UHF 50 n_a WENJ Cancel scan E NOTE You can press MENU button to cancel After all the available stations are stored the Channel List will be
51. o change channel Press the middle of the button the channel information banner will appear on screen Scroll through the stored channels by pushing the button up or down To change source Press the middle of the button twice the source list will appear on screen Scroll through the available sources by pushing the button up or down To turn the TV off Press the middle of the button and hold it down for a few seconds the TV will turn off into standby mode E NOTE You can move the switch upward or downward to change the volume If you want to change the channel press the middle of the switch once Position 3 and then move upward or downward If you press the middle of the switch once more the source OSD will be displayed To select desired source move the switch upward or downward and release If you press the middle of the switch and hold for a few seconds the TV will switch to standby mode The Main menu OSD cannot be displayed via the control buttons on the TV English 5 Remote Control Se eS eS 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 EC NOTE The Remote Control range is approximately 7m 23ft Source Sleep Timer Internet Portal Play Programme recording Rapid reverse in media browser mode Mono Stereo Dual I Il Current language in DVB channels Green button Red button Num
52. ownload or Timer is active The LED can also blink when you switch on the TV from standby mode First Time Installation When turned on for the first time the language selection menu appears The message Welcome please select your language is displayed and all language options are listed alphabetically Bienvenue Veuillez choisir une langue Fran ais Willkommen Wahlen Sie bitte Ihre Sprache aus Deutsch Benvenuti Selezionate la vostra lingua Italiano Bienvenido seleccione un idioma Espa ol Hos geldiniz l tfen dil se imini yap n z T rk e Dobrodo li izberite vas jezik Slovenski V lkommen v lj ditt spr k Svenska dv z lj k k rj k v lassza ki a nyelvet Magyar Bem vindo favor selecionar seu idioma Portugu s Tervetuloa valitse kielesi Suomi V ROCHE TEN A Set language Press the AN or Nr button to highlight the required language press OK button to select First Time Installation appears Use lt or button to set the required country and press Nf button to select Search Type Use lt or 2 to set the desired search type Available search types are Digital and analog digital only and analog only When set press N to select Teletext Language Use or 7 button to set the Teletext Language and select Scan Encrypted using AN or Nr button You can set Scan Encrypted as Yes if you wa
53. riangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock of persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance Please read these instructions fully before installing or operating Preparation Place the device on a solid even surface For ventilation purposes leave a free space of at least 10 cm all around the set To prevent any fault and unsafe situations do not place any objects on top of the set Use this device in moderate climates Operation temperature and operation humidity 5 C up to 45 C 85 rel humidity max Note Don t block ventilation holes intended Use This device is used to receive and display TV programmmes as well as to play CDs and DVDs see This device compatible disc types The different connection options make an additional expansion of the reception and display sources possible various external devices This device is only suitable for the operation in dry interiors This appliance is intended solely for private domestic use and may not be used for industrial and commercial purposes We exclude liability in principle if the device is not used as intended or unauthorized modific
54. rk through DLNA You can connect only one television with DLNA to the same network If a problem occurs with the DLNA network please switch your television off at the wall socket and back on again Trick mode and jump are not supported with the DLNA function Note There may be some PC s which may not be able to utilize the DLNA function due to administrator and security settings such as business PC s For best home network streaming with this TV the supplied Nero software should be installed Internet Portal Ensure the TV is connected to a Wired Wireless Internet connection After the connection is established you can select or view portal options Note A Broadband Internet connection is required for high quality viewing Ensure that the internet connection is made properly You must set the Country and Language data correctly in the First Time Installation for the proper operation of the internet portal Press button on your remote control and the portal application options will be displayed The application options will be displayed in a manner similar to the template below joomeo E Note on PIP Window If you switch to portal mode while watching TV channels current programme will be displayed on the PIP window You can change channels using P P buttons Current HDMI content will be displayed on the PIP window if you switch to portal mode while watching HDMI source Use the lt or
55. s recommended to use USB hard disk drive to record HD programmes Do not plug out the USB HDD during a recording This may harm the connected USB HDD Multipartiton support is available A maximum of two different partitions are supported If the disk has more than two partitions a crash may occur The first partition of the USB disk is used for PVR ready features It also must be formatted as the primary partition to be used for PVR ready features Some stream packets may not be recorded because of signal problems so sometimes the video may freeze during playback English 15 Record Play Pause Display for PlayListDialog keys can not be used when teletext is ON If a recording starts from timer when teletext is ON teletext is automatically turned off Also teletext usage is disabled when there is an ongoing recording or playback Timeshift Recording Press Il PAUSE button while watching a broadcast to activate timeshifting mode In timeshifting mode the programme is paused and simultaneously recorded to the connected USB disk Press gt PLAY button again to resume the paused programme from where you stopped You will see the timeshift gap between the real and the timeshifted programme in the info bar Instant Recording Press RECORD button to start recording an event instantly while watching a programme You can press RECORD button on the remote control again to record the next event on the EPG In this
56. splayed on screen You can review your contact list on the right side of the screen Your Skype name mood message and your camera preview if connected will be displayed on the left hand side of screen English 28 Adding a contact plugged into Skype Enter skype password By pressing the button select the Search Contacts option Enter the full name skype name or email address of the contact you want to find and add Use the remote control or virtual keyboard to enter a keyword Recent history Incoming call Icon meaning Your Skype history can be seen in this section To view recent history options use the p and p buttons To delete a conversation press the Red button When you press the OK button the contact review will be displayed Also Profile information can be displayed in this section English 29 Actions plugged into Skype Account Name Online Select a Menu by pressing the button mood messageand status profile picture Your contact list erdem19776 Ca e Press Ok to use Leo a video amp voice call Help bar Select a person from the contact list screen and press OK Choose an action from the list and then press OK to start the selected process Voice and video call is ready for your use If available you will see the thumbnail view of yours and the other person s camera feed When a conversation is active you can mute the microphone or p
57. t place the TV furniture etc on the power cord or pinch the cord e Handle the power cord by the plug do not unplug the TV by pulling the power cord e Never touch the power cord plug with wet hands as this could cause a short circuit or electric shock e Never make a knot in the power cord or tie it with other cords e Power cords should be placed in such a way that they are not likely to be stepped on or provide a trip hazard e A damaged power cord plug can cause fire or give you an electric shock When damaged it must be replaced this should only be done by qualified personnel oe Moisture and Water e Do not use this TV in a humid or damp place avoid using in the bathroom or near the kitchen sink e Do not expose this TV to rain or water as this may be dangerous e Do not place objects filled with liquids such as flower vases on top of the TV Avoid from dripping or splashing e If any solid object or liquid falls into the cabinet unplug the TV and have it checked by qualified personnel before operating it any further Ventilation e The slots and openings on the TV set are intended for ventilation and to ensure reliable operation e To prevent overheating these openings must not be blocked or covered in anyway Heat sources and Flames e Do not expose the TV to direct sunlight or other heat sources e The TV should not be placed near to open flames or sources of intense heat such as an electr
58. the installation wizard 7 3 Click the Next button e The integrated serial is displayed e Please do not change displayed serial Nero MediaHome 4 Essentials Installation E S Personalize Your Nero MediaHome 4 Essentials nero Please enter your serial number for Nero MediaHome 4 Essentials SE E 2M05 K0A6 M74C A2PK 1U7K A8UP 3939 A7XT CKU4 6647 9 4 Click the Next button e The License Conditions EULA screen is displayed Nero MediaHome 4 Essentials Installation Please read the License Conditions carefully End User License Agreement Software Products Object of this agreement is the Nero software suite comprising a selection of components that varies with different suite types as well as standalone applications and programs from the Following list Nero Burnin Nero Express InCD InCD Reader Nero StartSmart Nero Toolkit Nero CoverDesigner Nero WaveEditor Nero SoundTrax Nero BackItUp Nero Live Nero Live Gadget Nero Vision Nero Recode Nero ShowTime Nero PhotoSnap Nero PhotoSnap Viewer Nero MediaHome SecurDisc Viewer iscCopy Gadget Nero BackItUp amp Burn DTS Plug in Blu ray Video Plug in Gracenote Plug in Software Licensor Nero AG Nero THIS IS A LEGAL AGREEMENT BETWEEN YOU THE END USER AND NERO AG IM STOECKMAEDLE 13 15 76307 KARLSBAD GERMANY CONCLUSION OF THE CONTRACT THIS AGREEMENT IS EFFECTIVE E 1 accept the License Conditions 5 Please read the
59. uld try the following in such a case Keep at least three meters distance from microwave ovens mobile telephones bluetooth devices or any other Wi Fi compatible devices Try changing the active channel on the WLAN router Using DLNA Network Service DLNA Digital Living Network Alliance is a standard that eases the viewing process of digital electronics and makes them more convenient to use on a home network For further information visit www dlIna org The DLNA standard allows you to view and play photos music and videos stored in the DLNA media server connected to your home network 1 Nero Media Home Installation The DLNA function cannot be used if the server program is not installed on to your PC Please prepare your PC with the provided Nero Media Home programme For more information about the installation please refer to appendix H 2 Connect to a Wired or Wireless Network See the chapter Network Settings for detailed configuration information 3 Play Shared Files via Media Browser Select Media Browser by using the 4 or 7 buttons from the main menu and press OK The Media browser will then be displayed DLNA DLNA support is only available in the Media Browser folder mode To enable folder mode go to the Settings tab in the main media browser screen and press OK In the settings options highlight View Style and change to Folder using the LS or X buttons Select the desired media type and press
60. using N or NW buttons while in 14 9 Zoom Cinema or Subtitle Using the Channel List he Channel list Digital AeiaVandogue 1 BBC ONE ut i 2 BBC TWO ov O 3 ITV1 DTV 4 Channel 4 DTV 5 Channel 5 6 ITV2 7 BBC THREE 9 BBC FOUR 10 ITV3 11 Pick TV Sseaeaoaqcag cg 09 Walch filter ED bit Digital Cable Analoque The TV sorts all stored stations in the Channel List You can edit this channel list set favourites or set active stations to be listed by using the Channel List options Press MENU button to view main menu Select Channel List item by using Left or Right button Press OK to view menu contents Select Edit Channel List to manage all stored channels Use Up or Down and OK buttons to select Edit Channel List Press the Up or Down button to select the channel that will be processed Press the Left or Right button to select a function on the Channel List menu Use P P buttons to move page up or down Press MENU button to exit WB Digital AerialAnalogue e Sorting Channel List You can select which broadcasts will be listed in the channel list To display specific types of broadcast you should use the Active channel list setting Select the Active channel list from the Channel list menu by using M or Nw button Press the OK button to continue You can select a network type option from the list by using or and OK buttons Quick Menu
61. ut the other person on the line on hold Press the Red button to end a call English 30 Incoming call plugged into Skype Active events The incoming call dialog is shown when you are logged into Skype hiiia and when other users initiate a Skype call Fa A small dialog box will appear in the lower right corner of the TV screen whether the user watches TV or is browsing through Skype Use the remote control button and choose your action Dialing Phones The option to call phones is available if you have Skype Credit Please buy credit first Afterwards select a country then enter a phone number which you want to call Press the Yellow button to save an entered telephone number Press the Green button to start a conversation Settings All your Skype settings can be changed by using the Settings menu Please use P and P buttons on the remote control to move up or down Select an option then change the selected option by using the navigation buttons In the about section please find the Skype terms and conditions Please read this notice carefully English 31 Appendix B PC Input Typical Display Modes The display has a maximum resolution of 1920 x 1080 The following table is an illustration of some of the typical video display modes Your TV may not support different resolutions Supported resolution modes are listed below If you switch your PC to an unsupported mode a warning OSD will app
62. wer please check the power cord plug is connected to the mains power socket No picture 1 No Picture means that your TV is not receiving a transmission Have you selected the correct button on the remote control Try once more Also make sure the correct input source has been selected 2 Is the aerial connected properly 3 Are the plugs connected to the aerial socket 4 Is the aerial cable damaged 5 Are suitable plugs used to connect the aerial 6 If you are in doubt consult your dealer No sound 1 Has the TV been set to mute To cancel mute press the a button or increase the volume level 2 Sound is coming from only one speaker Is the balance set to one extreme See Sound Menu section Remote control does not operate Your TV no longer responds to the remote control The batteries may be exhausted if so you may need to replace the old battieries Input sources can not be selected 1 If you cannot select an input source it is possible that no device is connected 2 Check the AV cables and connections if you have tried to connect a device Recording Unavailable To record a programme you should first connect a USB disk to your TV while the TV is switched off You should then switch on the TV to enable recording feature Otherwise the recording feature will not be available If you cannot record try switching off the TV and then re inserting the USB device while the TV is switched off
63. wikipedia com www f flickr com facebooklecom ieee 5 09 08 2012 http google com 6 09 08 2012 http www facebook com 7 09 08 2012 http facebook com 8 09 08 2012 Yahoo 9 09 08 2012 http yahoo com e The browser does not support multiple tabs e Some internet pages include flash content These e You can search keywords by clicking the search are not supported by the browser button in the address dialog box or another way Your TV does not support any download processes to navigate to pages is by clicking on links on web from the web browser English 26 Getting Started with Skype Make voice calls and video calls with Skype on your TV Select the Skype app from the portal section to start a conversation plugged into Follow the on screen instructions to see how to operate related features NOTE Skype e Connect your supported webcam directly to the USB port on your TV e If the camera is not working properly switch off and unplug the TV Connect your camera again and turn the TV on e As soon as the TV is turned off Skype disconnects e Voice level and sound quality are affected by environmental noise e Call quality can change with accordance to your internet connection e Please visit www skype com to learn more information and to see the Terms of Use about Skype e The TV must be connected to a network for Skype connection e The Skype app will alert you when someone calls whilst

Download Pdf Manuals

Related Search

Related Contents

les Quais Bertrand inc.  User's Manual DP8340II SERIES [Parallel]  Rode BOOMPOLE  manual - Cembre  BAZZ P00139BG Installation Guide  Samsung WF7520N1B Инструкция по использованию    Mode d`emploi Konftel 55W  Samsung SGH-G600 Benutzerhandbuch  

Copyright © All rights reserved. Failed to retrieve file