Faber Diamante User's Manual
Contents
1. Make sure there is proper clearance within the wall or floor for exhaust duct before making cutouts Do not cut a joist or stud unless absolutely necessary If a joist or stud must be cut then a supporting frame must be constructed FOR MORE SPECIFIC DUCTWORK INFORMATION GO TO PAGE 4 WARNING To Reduce The Risk Of Fire Use Only Metal Ductwork A WARNING Venting system MUST terminate outside the home e DO NOT terminate the ductwork in an attic or other enclosed space e DO NOT use 4 laundry type wall caps Flexible type ductwork is not recommended DO NOT obstruct the flow of combustion and ventilation air Failure to follow venting requirements may result in a fire ELECTRICAL REQUIREMENTS A 120 volt 60 Hz AC only electrical supply is required on a separate 15 amp fused circuit A time delay fuse or circuit breaker is recommended The fuse must be sized per local codes in accordance with the electrical rating of this unit as specified on the serial rating plate located inside the unit near the field wiring compartment THIS UNIT MUST BE CONNECTED WITH COPPER WIRE ONLY Wire sizes must conform to the requirements of the National Electrical Code ANSI NFPA 70 latest edition and all local codes and ordinances Wire size and connections must conform with the rating of the appliance Copies of the standard listed above may be obtained from National Fire Protection Association Batterymarch Park Quincy2. Massachusetts 02269 For residential use only This appliance should be connected directly to the fused disconnect or circuit breaker through flexible armored or nonmetallic sheathed copper cable Allow some slack in the cable so the appliance can be moved if servicing is ever nec essary UL Listed 1 2 conduit connector must be provided at each end of the power supply cable at the appliance and at the junction box When making the electrical connection cut a 1 1 4 hole in the wall A hole cut through wood must be sanded until smooth A hole through metal must have a grommet WARNING TO REDUCE THE RISK OF FIRE ORELECTRIC SHOCK do not use this fan with any solid state speed control device WARNING TO REDUCE THE RISK OF FIRE ELECTRI CAL SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING Use this unit only in the manner intended by the manufacturer If you have any questions contact the manufacturer Before servicing or cleaning unit switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel CAUTION For General Ventilating Use Only Do Not Use To Exhaust Hazardous or Explosive Materials and Vapors WARNING TO REDUCE THE RISK OF FIRE ELECTRI CAL SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING Installa
3. provoquer une inflammation et le g n ration de fum e Utiliser toujours une puissance de chauffage moyenne ou basse pour le chauffage d huile b Veiller a toujours faire fonctionner le ventilateur de la hotte lors d une cuisson avec une puissance de chauffage lev e ou lors de la cuisson d un mets a flamber i e Crepes Suzette Cherries Jubilee Peppercorn Beef Flamb c Nettoyer fr quemment les ventilateurs d extraction Veiller ne pas laisser de la graisse s accumuler sur les surfaces du ventilateur ou des filtres d Utiliser toujours un ustensile de taille appropri e Utiliser toujours un ustensile de taille adapt la taille de l l ment chauffant AVERTISSEMENT POUR PREVENIR LES BLESSURES EN CAS DE FEU SUIVRE LES RECOMMANDATIONS SUIVANTES ETOUFFEZ LE FEU avec un couvercle m tallique et fermez le br leur Si le feu ne s teint pas tout de suite QUITTEZ LES LIEUX ET APPELEZ LES POMPIERS NE TOUCHEZ JAMAIS UNE CASSEROLE EN FLAMMES N UTILISEZ JAMAIS DE L EAU ou un torchon mouill pour teindre le feu ce qui pourrait causer une explosion de vapeur N utilisez un extincteur que si 1 Vous avez un mod le ABC et vous connaissez bien son mode d emploi 2 Le feu est petit et peu r pandu 3 Les pompiers sont d j pr venus 4 Vous avez une sortie derri re vous TOUTE OUVERTURE DANS LE MUR OU LE PLANCHER PROXIMIT DE LA HOTTE DOIT TRE SCELLE Gardez 24 po de hauteur entre le bas de la hotte et la surfac
4. range from cabinet open ing to provide easier access to rear wall Put a thick protective covering over cooktop set in range or countertop to protect from damage or dirt 2 Determine and clearly mark with a pencil the center line on the wall where the rangehood will be installed 3 Based on your ceiling height and or personal preference deter mine the distance you would like between the bottom of the hood and the cooktop distance X in FIGURE 4A OR 4B Drawa horizontal line the height of distance X plus 13 3 4 as indicated in FIGURE 5A INSTALLATIONS WITH NO BACKSPLASH distance X plus 13 3 4 FIGURE 5A INSTALLATIONS WITH NO BACKSPLASH For installations using the 24 or 30 High Backsplash draw a horizontalline as indicated in FIGURE 5B INSTALLATIONS WITH BACKSPLASH 13 3 4 above the top of the Backsplash m ep z as O x ep N ap FIGURE 5B INSTALLATIONS W 24 OR 30 HIGH BACKSPLASH 4 Place the UPPER CHIMNEY MOUNTING BRACKET E on the wall as shown 1 16 from the ceiling aligning the center notch with the vertical center line Mark the wall at the centers of the holes in the bracket 5 Place the LOWER CHIMNEY MOUNTING BRACKET E on the wall as shown at 16 1 8 below the upper bracket aligning the center notch with the vertical center line Mark the wall at the centers of the holes in the bracket 6 Install the CHIMNEY MOUNTING BRACKETS E on the wall using the MOUNTING SCREWS D pro
5. than one is used Do not install two elbows together If you must elbow right away do it as far away from the hood s exhaust opening as possible Version 12 04 Page 4 vented to the outside The Diamante chimneys are adjustable and designed to meet varying ceiling heights as indicated in FIGURE 4A The chimneys can be adjusted for ceilings between 7 5 3 4 and 8 10 3 4 depending on the distance between the bottom of the hood and the cooktop distance x For shorter ceilings have the chimney cover s cut at a sheet metal shop For higher ceiling installations the High Ceiling Chimney Kit includes anew 40 upper chimney which would replace the 16 1 8 upper chimney that came with the hood Note If 24 or 30 High Backsplash is being installed the distance between the bottom of the hood and the cooktop DISTANCE X IN FIGURE 4A is equal to the height of the Backsplash 5 1 8 min 16 1 8 max 21 1 4 3 3 8 36 x distance from hood to cooktop varies depending on installation min 24 suggested max 30 manufacturer s recommendation 21 1 4 upper chimney cover lower chimney cover canopy 201 also consult cooktop 26 3 8 MAX 37 3 8 MIN DUCTED INSTALLATION DIMENSIONS min amp max ceiling height examples x 24 x 26 x 28 x 30 min min min min 7 53 4 7 73 4 7 9 3 4 7 11 3 4 max max max max
6. tre du fil devra aussi se conformer aux r glements du code national lectrique ANSI NFPA 70 ainsi qu aux r glements locaux et les sp cifications de cet appareil On peut obtenir ces informations chez l Association Nationale de la Pr vention du Feu Batterymarch Park Quincy Massachusetts 02269 Raccordez cet appareil directement au coupe circuit avec un fil flexiblle couvert en cuivre en laissant un peu de lachement dans le fil pour permettre le d placement de l appareil Veillez ace qu un contact d un demi pouce 1 2 po soit install chaque bout de fil soit l appareil ainsi qu la boite fusible Faites un trou de 1 1 4 po dans le mur S il s agit d un trou en bois sablez le bien tandis qu un trou passant par le m tal demande un bouche trou AVERTISSEMENT POUR R DUIRE LE RISQUE D INCENDIE OU DE CHOC ELECTRIQUE ne pas utiliser ce ventilateur en conjonction avec un dispositif de r glage de vitesse semi conducteurs AVERTISSEMENT POUR MINIMISER LES RISQUES D INCENDIE CHOC ELECTRIQUE OU DOMMAGES CORPORELS OBSERVER LES PRESCRIPTIONS SUIVANTES Suivez les recommandations du fabricant et entre en communication avec lui pour toute information Fermez le courant avant tout entretien et veillez ace qu il reste ferm Si on ne peut pas verrouiller le panneaux du service lectrique affichez un avis de danger sur la porte AVIS Pour L vacuation G n rale Veillez Ne Pas Evacuer Des Mat ria
7. 8 4 3 4 8 6 3 4 8 8 3 4 8 10 3 4 cabinet base FIGURE 4A DUCTED INSTALLATIONS Version 12 04 Page 5 DUCTLESS INSTALLATION DIMENSIONS not vented to the outside PE upper i ji chimney 16 1 8 max cover The Diamante chimneys are adjustable and ductless designed to meet varying ceiling heights ee lower as indicated in FIGURE 4B For ductless chimney installations the chimneys can be adjusted CONG for ceilings between 7 11 3 8 and 8 11 1 2 dependingonthedistancebetweenthebottom Le of the hood and the cooktop distance x 22 For shorter ceilings have the chimney cover s min amp max ceiling height examples cut at a sheet metal shop For higher ceiling x distance from hoodto cooktop _ an oan _ ggu _ ann installations the High Ceiling Chimney Kit ates depending on instalation ma lt a paris Neue ade trie ppercomney wmon would also consult cooktop 7 113 8 8 13 8 8 33 8 8 538 replace the 16 1 8 upper chimney that came manufacturer s recommendation max max max mia with the hood 8 542 87 1 2 8 91 B 1112 Note If 24 or 30 High Backsplash is being installed the distance between the bottom of the hood and the cooktop DISTANCE X IN FIGURE 4B is equal to the height of the Backsplash 36 cabinet base FIGURE 4B DUCTLESS INSTALLATIONS MAX 38 1 8 MIN 32 _3 3 8 Version 12 04 Page 6 PREPARE THE WALL 1 Disconnect and move freestanding
8. FAFABER DIAMANTE Wall Mount Canopy Rangehood Installation Instructions e Use and Care Information READ AND SAVE THESE INSTRUCTIONS The Installer must leave these instructions with the homeowner The homeowner must keep these instructions for future reference and for local electrical inspectors use READ THESE INSTRUCTIONS BEFORE YOU START INSTALLING THIS RANGEHOOD WARNING TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE a Never leave surface units unattended at high settings Boilovers cause smoking and greasy spillovers that may ignite Heat oils slowly on low or medium setting b Always turn hood ON when cooking at high heat or when flambeing food i e Crepes Suzette Cherries Jubilee Pepper corn Beef Flamb c Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filter d Use proper pan size Always use cookware appropriate for the size of the surface element WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE OBSERVE THE FOLLOWING SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray then turn off the burner BE CAREFUL TO PREVENT BURNS If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT NEVER PICK UP A FLAMING PAN You may be burned DO NOT USE WATER including wet dishcloths or towels a violent steam explosion will result Use an extinguisher ONLY if 1 You know you have a Class ABC extinguisher and y
9. TIE SSR RASS N FIGURE 12 2 Turn the power supply on Turn on blower and lights If the rangehood does not operate check that the circuit breaker is not tripped or the house fuse blown If the unit still does not operate disconnect the power supply and check that the wiring connec tions have been made properly WIRING DIAGRAM Q DIRECTIONAL LAMP Il x mr o x CAPACITOR VOLTAGE 120V 60 Hz 100V 50 60 Hz 25 u F 240 V This rangehood uses 20 watt halogen lamps USE AND CARE INFORMATION This rangehood system is designed to remove smoke cooking vapors and odors from the cooktop area For Best Results Startthe rangehood several minutes before cooking to develop proper airflow Allow the unit to operate for several minutes after cooking is complete to clear all smoke and odors from the kitchen Rangehood Control Panel The control panel is located on the front edge of the rangehood canopy The position and function of each control button are indicated in FIGURE 13 Light On Off Button L On Off switch for the halogen lights Push the button in to turn the light ON push again to turn the light OFF FIGURE 13 T Blower Indicator IN Light 1 9 a Lights up to indicate or y blower is ON a Blower On Off and Speed Buttons 1 2 3 Push button 1 to turn ON and OFF the blower This button must be pushed in for the blower to operate regardless of speed
10. Y DUCTLESS 2 LEFT VENT GRID 3 RIGHT VENT GRID 4 DIVERTER EXTENSION HORIZONTAL 2 PIECES 5 DUCTLESS DIVERTER 6 CHARCOAL FILTER FIGURE 8 FOR DUCTLESS INSTALLATIONS Ductless installations require a Ductless Conversion Kit whose components are pictured in FIGURE 8 Do not use the DAMPER H in FIGURE 1 for ductless installations The LOWER CHIMNEY COVER B in FIGURE 1 should be discarded and replaced by a new one with holes 1 in FIGURE 8 1 As indicated in FIGURE 8 fit the DUCTLESS DIVERTER 5 over the duct outlet Fit the 2 DIVERTER EXTENSION HORIZONTAL pieces 4 on either side of the DUCTLESS FIGURE 10 DIVERTER 2 Install the CHARCOAL FILTER 6 behind the center grease filter opening by inserting and locking into place as indicated FOR DUCTLESS in FIGURE 9 INSTALLATIONS Fit the LEFT AND RIGHT VENT GRIDS 2 and 3 into the LOWER CHIMNEY DUCTLESS holes making sure that the directional symbols are towards the top and front of the hood and that they connect snugly to the DIVERTER EXTENSION FIGURE 11 HORIZONTAL pieces FIGURE 9 Version 12 04 Page 8 FOR ALL INSTALLATIONS 1 Install the grease filters using two hands by first pulling and turning the knob to the left so that the locking lever does not protrude from the filter as in FIGURE 12 Insert the opposite end of the filter into the retaining channel Insert the knob end next then turn knob to the right to lock the filter into place
11. aler from whom you purchased the rangehood or the local Faber distributor If you cannot identify a local Faber distributor contact us at 508 358 5353 for the name of a distributor in your area Version 12 04 Page 9
12. chosen Button 1 operates the blower on LOW speed Push button 2 for MEDIUM speed Push button 3 for HIGH speed Cleaning The stainless steel grease filters should be cleaned frequently in hot detergent solution or washed in the dishwasher Stainless steel cleaner should be used on stainless rangehoods Abrasives and scouring agents can scratch stainless steel finishes and should not be used to clean finished surfaces Replacing the Lamps Before attempting to replace the lamps make sure that the light switch is turned off Remove the 2 screws as indicated in FIGURE 14 that hold the light support and gently pull the support down from the hood Remove the lamp from the light support and replace with new lamp Replace the light support and fix it into place with the 2 screws FIGURE 14 WARRANTY amp SERVICE All Faber products are warranteed against any defect in ma terials or workmanship for the original purchaser for a period of 1 year from the date of original purchase This warranty covers labor and replacement parts The warranty does not cover consumable parts such as filters and light bulbs This warranty does not apply if this product has been subjected to faulty installation misuse or neglect This warranty excludes any consequential expense or damage resulting from any use or malfunction of the product All implied warranties are limited to the duration of this warranty To obtain warranty service contact the de
13. coudes pour la plus grande efficacit Le diam tre de tuyauterie doit tre uniforme N installez jamais 2 coudes ensemble Scellez bien tous les joints avec un ruban adh sif m tallique l int rieur et scellez bien le clapet ext rieur avec du calfeutrage Utilisez un tuyau d vacuation rigide lorsque possible Un tuyau flexible gale deux fois plus qu un tuyau rigide ce qui r duit la puissance d vacuation Veillez ce que l espace pour le tuyau soit ample ainsi on n aurait pas besoin de d couper les supports de mur int rieur Si ce d coupage est n cessaire veillez bien ce qu un renforcement soit mis en place R GLEMENTS D EVACUATION ADDITIONELL PAGE 10 AVERTISSEMENT Pour Ne Pas Risquer Un Feu Utilisez Seulement Les Mat riaux Metalliques AVERTISSEMENT e Le syst me d vacuation DOIT sortir l ext rieur e NEVACUEZ PAS le conduit soit dans une mansarde soit dans un espace enferm e N UTILISEZ PAS un clapet de s choir 4 pouces e N utilisez pas un conduit flexible e N ENCOMBREZ PAS la circulation d air e Faute de suivre cet avertissement pourrait occasionner un feu FICHE TECHNIQUE LECTRIQUE Le raccordement lectrique doit se faire avec un circuit s par de 15 amperes fusible 120V 60 Hz courant alternant On recommande un coupe circuit La taille du fusible doit se conformer aux codes municipaux suivant la sp cification lectrique sur la plaque int rieure Le diam
14. e de cuisson Cette hauteur minimum peut tre plus haute suivant le code municipal Par exemple les cuisini res gaz peuvent requ rir 30 po de hauteur Les armoires au dessus ne d passeront pas 13 po de profondeur Les armoires au dessus de chaque c t devront tre au moins 18 po au dessus de la surface de cuisson Consultez la fiche technique avant de d couper les armoires L installation de cette hotte doit tre conforme aux Reglements de Manufactured Home Construction and Safety Standards titre 24 CFR Section 3280 anciennement Federal Standard for Mobile Home Construction and Safety Standards titre 24 CFR Section 3280 anciennement Federal Standard for Mobile Home Construction and Safety titre 24 HUD Section 280 Le branchement lectrique se fait avec une raccordement a 4 fils Consultez la fiche technique lectrique Version 12 04 Page 1 VENTING REQUIREMENTS Determine which venting method is best for your application Ductwork can extend either through the wall or the roof The length of the ductwork and the number of elbows should be kept to a minimum to provide efficient performance The size of the ductwork should be uniform Do not install two elbows together Use duct tape to seal all joints in the ductwork system Use caulking to seal exterior wall or floor opening around the cap Flexible ductwork is notrecommended Flexible ductwork creates back pressure and air turbulence that greatly reduces performance
15. hood canopy Failure to properly lift rangehood could result in damage to the product or personal injury PLAN THE INSTALLATION This rangehood can be installed as either ducted or ductless The blower can be vented through the wall or ceiling To vent through a wall a 90 elbow is used When installed ductless the rangehood vents out of grates on the sides of the chimney Ductless installations require a Ductless Conversion Kit available from your dealer WARNING BEFORE MAKING ANY CUTS OR HOLES FOR INSTALLATION DETERMINE WHICH VENTING METHOD WILLBE USEDAND CAREFULLY CALCULATE ALL MEASUREMENTS RANGEHOOD COMPONENTS A CANOPY SECTION B LOWER CHIMNEY COVER C UPPER CHIMNEY COVER D MOUNTING SCREWS E CHIMNEY MOUNTING BRACKETS F MOUNTING PLUGS G CHIMNEY SCREWS H DAMPER FIGURE 1 CALCULATE THE DUCTRUN LENGTH The ductrun should not exceed 35 equivalent feet if ducted with the required minimum of 6 round duct Calculate the length of the ductwork by adding the equivalent feet in FIGURE 2 for each piece of duct in the system An example is given in FIGURE 3 3 0 feet 5 0 feet 12 0 feet 0 0 feet 45 Elbow 90 Elbow 9 Feet Straight Duct 9 0 feet 2 90 Elbows 10 0 feet Wall Cap 0 0 feet Total System 19 0 feet FIGURE 3 90 Flat Elbow Wall Cap FIGURE 2 For best results use no more than three 90 elbows Make sure that there is a minimum of 24 of straight duct between elbows if more
16. ou already know how to operate it 2 The fire is small and contained in the area where it started 3 The fire department is being called 4 You can fight the fire with your back to an exit ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST BE SEALED This rangehood requires at least 24 of clearance between the bottom of the rangehood and the cooking surface or countertop This minimum clearance may be higher depending on local building code For example for gas ranges a minimum of 30 may be required The maximum depth of overhead cabinets is 13 Overhead cabinets on both sides of this unit must be a minimum of 18 above the cooking surface or countertop Consult the cooktop or range installation instructions given by the manufacturer before making any cutouts MOBILE HOME INSTALLATION The installation of this rangehood must conform to the Manufactured Home Construction and Safety Standards Title 24 CFR Part 3280 formerly Federal Standard for Mobile Home Construction and Safety Title 24 HUD Part 280 Four wire power supply must be used and the appliance wiring must be revised See Electrical Requirements LISEZ BIEN CETTE FICHE AVANT D INSTALLER LA HOTTE AVERTISSEMENT POUR MINIMISER LE RISQUE D UN FEU DE GRAISSE SUR LA TABLE DE CUISSON a Ne jamais laisser un l ment de la table de cuisson fonctionner sans surveillance la puissance de chauffage maximale un renversement d bordement de mati re graisseuse pourrait
17. stallations the DAMPER H in FIGURE 1 must be attached to the exhaust opening on the top of the CANOPY SECTION Connect the ductwork and seal all connections with duct tape PROCEED TO FOR ALL INSTALLATIONS ON NEXT PAGE Version 12 04 Page 7 FOR ALL INSTALLATIONS 1 Remove the cover from the Field Wiring Compartment with a phil lips screwdriver Feed the Power Supply Cable through the electrical knockout Connect the Power Supply Cable to the rangehood cable Attach the White lead of the power supply to the White lead of the rangehood with a twist on type wire connector Attach the Black lead of the power supply to the Black lead of the rangehood with a twist on type wire connector Attach the Power Supply Cable grounding lead to the green screw provided Using the 4 holes provided screw the Field Wiring Compartment to the wall as dictated by your Power Supply Cable location screws not provided Replace the cover 2 Install the UPPER CHIMNEY COVER C in FIGURE 10 by slightly widening the two sides and hooking them behind the CHIMNEY MOUNTING BRACKETS E Secure the sides to the CHIMNEY MOUNTING BRACKETS with the 4 CHIMNEY SCREWS G 3 Install the LOWER CHIMNEY COVER B by slightly widening the two sides of the LOWER CHIMNEY COVER and hooking them between the UPPER CHIMNEY COVER and the wall making sure that it fits snugly Secure the LOWER CHIMNEY COVER to the CANOPY SECTION A with 2 CHIMNEY SCREWS G 1 LOWER CHIMNE
18. tion WorkAnd Electrical Wiring Must Be Done By Qualified Person s In Accordance With All Applicable Codes And Standards Including Fire Rated Construction Sufficient air is needed for proper combustion and exhausting of gases through the flue chimney of fuel burning equipment to prevent backdrafting Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA andthe American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and the local code authorities When cutting or drilling into wall or ceiling do not dam age electrical wiring and other hidden utilities Ducted fans must always be vented to the outdoors A WARNING Electrical ground is required on this rangehood If cold water pipe is interrupted by plastic nonmetallic gaskets or other materials DO NOT use for grounding e DO NOT ground to a gas pipe DO NOT have a fuse in the neutral or grounding circuit A fuse in the neutral or grounding circuit could result in electrical shock e Check with a qualified electrician if you are in doubt as to whether the rangehood is properly grounded Failure to follow electrical requirements may result in a fire Version 12 04 Page 2 REGLEMENTS D EVACUATION Confirmer la sortie d vacuation soit par le mur soit par le toit Utilisez une longueur de tuyauterie minimale avec les moindres de
19. ur usage menager Version 12 04 Page 3 TOOLS NEEDED FOR INSTALLATION e Saber Saw or Jig Saw e Drill 1 1 4 Wood Drill Bit e Scissors e Pliers e Phillips Screwdriver Flat Blade Screwdriver e Wire Stripper or Utility Knife e Metal Snips e Measuring Tape or Ruler e Level e Pencil e Caulking Gun e Duct Tape PARTS SUPPLIED FOR INSTALLATION 1 Hardware Package e 1 Literature Package PARTS NEEDED FOR INSTALLATION e 2 Conduit Connectors e Power Supply Cable 1 Wall or Roof Cap e All Metal Ductwork OPTIONAL ACCESSORIES AVAILABLE e Backsplash Choose either 24 or 30 high mounts to the wall beneath the rangehood for a coordinated look 30 X 24 high part 6098835 Stainless 36 X 24 high part 6098815 Stainless 30 X 30 high part 620000095 Stainless 36 X 30 high part 620000096 Stainless High Ceiling Chimney Kit One 40 upper chimney to replace 16 1 8 upper chimney that came with hood part 620000071 Stainless Ductless Conversion Kit For non vented installations only it is highly recommended that professional style cooking always be vented to the outside part 620000072 Stainless Replacement Charcoal Filter For non vented installations only replace charcoal filter as needed part 620000041 A WARNING PERSONAL INJURY HAZARD Because of the weight and size of the rangehood canopy two or more people are needed to move and safely install the range
20. ux Ou Vapeurs Explosif AVERTISSEMENT POUR MINIMISER LES RISQUES D INCENDIE CHOC ELECTRIQUE OU DOMMAGES CORPORELS OBSERVER LES PRESCRIPTIONS SUIVANTES L installation Et Le Raccordement Electrique Doivent Se Faire Par Un Technicien Qualifi Selon Tous Les Codes Municipaux Afin d obtenir un rendement maximal en ce qui a trait la combustion ainsi qu l vacuation des gaz par la conduite de chemin e une bonne a ration est n cessaire pour tous les appareils combustion Suivez les conseils et mesures de s curit du fournisseur tels que ceux publi s par l Association Nationale de la Sauvegarde contre l incendie et l Association Am ricaine d Ing nieurs de Chauffage Frigorifaction et Air Climatis ainsi que les codes municipaux En per ant un mur veillez ne pas perforer un autre fil lectrique Une ventilateur vacuation ext rieure doit tre raccord e l ext rieur A AVERTISSEMENT Une prise a terre est n cessaire pout cette hotte e N utilisez pas un tuyau l eau froide pour la mise terre s il est branch un joint plastique non m tallique ou autre e NE JOIGNEZ PAS la mise a terre a conduit de gaz e N INSTALLEZ PAS un fusible dans le circuit de mise terre ce qui peut causer une secousse lectrique e V rifiez avec un lectricien certifi ce que la hotte soit bien mise terre e Faute de suivre ces recommandations pourrait occasionner un feu Uniquement po
21. vided 7 Forthe most secure installation the MOUNTING SCREWS D which mount the CANOPY SECTION A in FIGURE 1 should be installed into wood Mark the wall along the horizontal line 4 9 16 in from the center line on either side as indicated in FIGURE 5A or 5B and install the MOUNTING SCREWS into the wall leaving about 1 4 gap between the wall and the head of the screw 8 For ducted installations determine and make all necessary cuts in the wall for the ductwork Install the ductwork before the rangehood 9 Determine the proper location for the Power Supply Cable by making sure it 1 Allows the LOWER CHIMNEY COVER to hide the Field Wiring Compartment 2 Does not have ductwork blocking your access to the Field Wiring Compartment Use a1 1 4 Drill Bit to make this hole Run the Power Supply Cable Use caulking to seal around the hole DO NOT turn on the power until installation is complete INSTALL THE RANGEHOOD 1 Remove the grease filters from the unit by pulling the knob forward while turning it to the left releasing the lock ing lever FIGURE 6 2 Before mounting the CANOPY SECTION tighten the two leveling screws located near the CANOPY SECTION mounting points as indicated in FIGURE 7 leveling screws FIGURE 7 3 Hook the body on to the MOUNTING SCREWS D in FIG URE 7 and fully tighten the MOUNTING SCREWS 4 Adjust the leveling screws to level the CANOPY SEC TION 5 For ducted in
Download Pdf Manuals
Related Search