Extron electronic SW2 User's Manual
Contents
1. buttons or by using the contact closure controller e If the switcher is in autoswitching mode rear panel Contact Auto sw pins are jumpered together the switcher automatically selects the highest numbered input with an active sync signal e The image should now appear on screen and sound from the audio source should be audible If image or audio problems occur see Troubleshooting in the SW2 VGA DA2 AF R User s Manual for further details Extron USA West Extron USA East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Headquarters q 800 633 9876 800 3987 6673 800 7339 8766 81 3 3511 7655 400 883 1568 971 4 2991800 800 633 9876 Inside USA Canada Only Inside Europe Only Inside Asia Only 81 3 3511 7656 FAX Inside China Only 971 4 2991880 FAX 68 460 52 Inside USA Canada Only 1 919 863 1794 31 33 453 4040 65 6383 4400 86 21 3760 1568 Rev A 1 714 491 1500 1 919 863 1797 FAX 31 33 453 4050 FAX 65 6383 4664 FAX 86 21 3760 1566 FAX 07 09 1 714 491 1517 FAX 2009 Extron Electronics All rights reserved2. pin HD connector output A is also provided for a local monitor Step 5 Audio output Connect an audio device to the 3 5 mm 5 pole captive screw connector for balanced or unbalanced audio output For correct wiring follow the diagram below Tip Tip Ring g NO Ground Here Sleeve s Sleeve s Tip Tip Ring 7 NO Ground Here i Balanced Audio Output a Unbalanced Audio Output CAUTION i an 2 5 mm MAX For unbalanced audio connect the sleeve s to the ground contact Do not tin the wires DO NOT connect the sleeve s to the negative contacts Step 6 Autoswitching contact closure Connect a contact closure control device to the left three pins of the 3 5 mm 5 pole captive screw connector e Pin 1 selects input 1 when connected to ground pin 3 e Pin 2 selects input 2 when connected to ground pin 3 e Pin 3 connects to the ground wire equipment ground e Pins 4 and 5 if jumpered or shorted together will turn the autoswitching mode on When the autoswitching mode is on the switcher automatically switches to the highest numbered input that has an active sync signal CONTACT AUTO Sw Jumper pins 4 amp 5 for autoswitching Contact Closure Control See Rear Panel Features in the SW2 VGA DA2 AF R User s Manual for details Step 7 Operation Power up all input and output devices and the switcher e If the switcher is in manual switching mode select an input from the front panel
3. Setup Guide SW2 VGA DA2 AF R This guide provides basic instructions for an experienced installer to set up and operate the Extron SW2 VGA DA2 AF R switcher LBC w Audio Cable Extron SW2 VGA DA2 AF R ria Switcher onnection Network Connection Laptop or VGA Computer LCD Projector Installation Step 1 Mount the unit Turn off all equipment or disconnect it from power sources and mount the switcher as desired See Installing Adapter Plates and Mounting the SW2 VGA DA2 AF R in the SW2 VGA DA2 AF R User s Manual for details e On desk Place 4 rubber feet provided onto the four corners of the switcher e Rack Use the optional 1U Rack Shelf part 70 485 01 e Under desk Use the optional Under Desk Mount Kit part 70 212 01 Step 2 Video inputs Connect an RGBHV RGBS RGsB or RsGsBs video input to each 15 pin HD input connector as desired One connector is on the front panel and a second connector is on the rear panel Step 3 Audio inputs Connect an unbalanced stereo input to each 3 5 mm stereo mini jack as desired One jack is on the front panel and a second jack is on the rear panel Wire the audio plug as shown below Tip L ee3r _ _ _ Sleeve Continued on reverse side Setup Guide SW2 VGA DA2 AF R Step 4 Video outputs Connect an RGBHV RGBS RGsB or RsGsBs video display to the 15 pin HD connector output B A 15
Download Pdf Manuals
Related Search