Extron electronic Extron Electronics Switch DVC 501 SD User's Manual
Contents
1. User Guide for a complete list of available SIS commands ASCII command Response Host to Converter Converter to Host Mute video 1B Vmt1 lt e4 Mute the video output Unmute video B Vmt 4 Display the video output Mute audio 1Z Amt1 lt Mute the audio output Unmute audio OZ Amt lt Unmute the audio output Command Additional Description Enable lock executive mode 1X Exeie Lock all front panel functions Disable lock mode OX Exe 4 Enable all front panel functions 2 2011 Extron Electronics All rights reserved www extron com 68 1518 50 Rev C 09 112. B Y analog RGB RGBHV RGBS and RGsB or YUV component video connector 6 Connect a control device Connect a host device such as a computer or touchpanel control system to one or both of the following DVC ports to configure and control the DVC via Simple Instruction Set SIS commands e RS 232 port rear panel Connect a host device to the Tx Rx and ground pins of this 5 pole captive screw connector The first and second pins of this connector are not used The default protocol for this port is 9600 baud 1 stop bit no parity 8 data bits and no flow control e Config port front panel Connect a USB cable USB A to USB mini B between a USB port on your computer and this port Q on the front panel illustration on the next page 7 Connect the audio output Connect an amplifier or other audio output device to the 5 pole captive screw audio connector on the rear panel illustration as shown below 3 5 mm MAX j 86mm Do not tin the wires Balanced Audio Output Unbalanced Audio Output CAUTION For unbalanced audio connect the sleeves to the ground contact DO NOT connect them to negative contacts 8 Connect power to the DVC 501 SD by plugging a standard IEC power cord provided from a 100 to 240 VAC 50 60 Hz power source into the power receptacle Front Panel Features MENU ADJUS l o gt a vy CONFIG Extron DVC 501 SD DIGITAL VIDEO CONVERTER USB Co
3. nfig port LCD screen Menu button Next button Adjust knobs Configuring the DVC 501 SD Using the Front Panel Menu selections are displayed on the LCD screen To use any menu press the Menu button repeatedly until the desired menu is displayed see the menu flow diagram below Press the Next button repeatedly until the desired submenu appears Rotate an Adjust knob to select an item from a submenu To return to the main menu at any time press the Menu button After 30 seconds of inactivity the screen displays the default cycle 1 From the Output Config submenus use the Adjust knobs to select the output signal ies type and the sync polarity to match the requirements of the display device Cycle V 2 From the Advanced Config menu Test Pattern submenu select the Crop Crosshatch Colorbars and Grayscale test patterns to confirm that the settings of the display device vic are correct NOTE Test pattern timings are based on the incoming SDI signals and are not OUTPUT CONFIG displayed if an active signal is not present 3 Use the Audio Config submenus to configure the audio as desired Supported Input Resolutions EXIT MENU PRESS NEXT NOTE The output resolution always matches the input resolution Simple Instruction Set SIS Commands When setting up the DVC 501 SD you can issue SIS commands from your computer via RS 232 or USB as an alternative to the front panel controls See the DVC 507 SD Series
4. of Ase RY 3 w3 Extron Electronics To o INTERFACING SWITCHING AND CONTROL UTI DVC 501 SD Setup Guide The Extron DVC 501 SD receives SD SDI HD SDI and 3G SDI serial digital video signals and converts them to DVI D and analog RGB or component video It is compliant with SMPTE 259M 292M 424M and ITU digital video standards The RGB output can be set for RGBHV RGBS and RGsB Bi level or tri level sync can be selected when the unit is set for component video output The DVC 501 SD features extraction of embedded AES3 audio RS 232 and USB serial control and a buffered loop through that delivers reshaped and restored multi rate SDI signals 100 240Vy 0 3A MAX U HROUGH AC power connector DVI D output connector Audio output connector 3G HD SD SDI input connector RGB YUV output connector RS 232 connector Buffered Loop through connector Installation Steps 1 Disconnect power from all equipment 2 Optional Mount the unit to a rack or furniture 3 Connect the video input Connect an SD SDI HD SDI or 3G SDI source to the 3G HD SD SDI port of the BNC input connector in the rear panel illustration above 4 Optional Connect a monitor or recording device Attach a monitor or video recording device to the Buffered Loop through BNC connector 5 Connect the video output Connect a display or other output device to the DVD D digital video connector or to the RGB R Y Y
Download Pdf Manuals
Related Search