Extron electronic Extron Electronics Switch 600 User's Manual
Contents
1. Connect the System Controller to the Switcher Connect the COM port of the system controller to the RS 232 port on the switcher with the provided control cable System Controller Switcher IPL T PC1 SW4 HDMI COM RS 232 AUTO Tx Rx Y 4 pole connector 5 pole connector to system controller to switcher Switcher Control Cable ATTENTION The two ends of the RS 232 control cable are different One has a 4 pole connector the other has a 5 pole connector Connect Power The system controller uses an internal power supply Connect the power cord to a wall outlet The TeamWork 600 systems use a 6 input switcher with an internal power supply Connect the power cord to a wall outlet The TeamWork 400 systems use a 4 input switcher with a 12 VDC 1 A power supply which is provided with the switcher ATTENTION Do not connect the power supply to the SW4 HDMI switcher until you have read the Attention notifications in the Wiring the Power Supply section of the SW HDMI Series User Guide The optional TeamWork VGA kit also includes a 12 VDC 1 A power supply for the analog to digital converter Converter SIS Commands The following features have been pre configured on the RGB HDMI 300 A The values should be re entered if they have been erased by a factory reset See the RGB DVI 300 and RGB HDMI 300 A User Guide at www extron com for a complete explanation of SIS commands Esc Escape key2. Sherf Brackets OUTPUT N to switcher Bottom of Cable Cubby Power Module AAP Shelf Assembly with Cable Pass through Blank AAP Show Me Cables must be inserted into shelf assemblies as itis being constructed TeamWork Kits Installation Guide Continued Mounting and Placement of System Components Decide where you will install your TeamWork system and where the individual components will be placed The Cable Cubby should provide easy access for as many users as possible Ensure that there is ample space for cables under the table Ensure that the edge on which the lid opens is correctly oriented The system controller should be placed close to the display The SW4 HDMI or SW6 HDMI switcher should be placed close to the Cable Cubby The analog to digital converter with the optional TeamWork VGA kit should be placed next to the switcher Ensure that the VGA connector can connect to the converter and the three conductor pigtail can connect to the switcher d ei Show Me VGA Show Me Cable 7 fete HDMI Video to Display ain in p en SaR VGA Kit optional FT oo Uu AC Power To Display Power Supplies 2 System Controller Extron Cable Cubby Cable Access Enclosure Shown mounted with optional Extron UTS 100 UTS 150 Under Table Shelf System Secure Show Me Cable to Cable Cubby and create a loop Installing the Cable
3. lt Carriage return no line feed Enable power save mode Esc 1 PSAV lt Enable Auto lmage 1 1A Disable auto memories Esc AMEM lt Enable front panel security lockout 1X 10 Testing the System The TeamWork system has been pre configured so that once all the connections have been made and the devices are all powered on there should be no need of further configuration for the system to work To ensure that the system has been set up correctly follow these steps 1 Power on the equipment e Source devices e Switcher e System controller IPL T PC1 2 Press the power button O on the front panel of the system controller The LED 2 lights green when power is being supplied to the attached output device Turn on the display and confirm that the display is receiving power Extron Ci LINK IPLT PC1 Go to the menu for the display and disable the Sleep Mode feature If necessary see the display user guide xt 100 O R O INPUT LINK 5 Press the power button on the power controller The LED should go out RO OIR ACT and the display should be turned off 6 Connect one of the Show Me cables to a video source such as a laptop 7 Press the Show Me button on that cable If the source device is providing a video signal the LED on the Show Me cable lights blue and the display automatically turns on 8 Connect a second Show Me cable to a second video source Repeat
4. Cubby in the Table Before cutting the table and installing the Cable Cubby see the Cable Cubby Setup Guide see www extron com ATTENTION e Ensure that the orientation of the cable cubby and the hole dimensions are correct before cutting the table e After installation secure the cables to avoid them becoming tangled see the figure above Cabling Contact Closure Extron IPL T PC1 amp Tally Flat Panel System Controller AC Cord RS 232 Control Cable Extron HDMI Pro Cable HDMI Video Extron SW4 HDMI Switcher Flat Panel Display w Integrated Speakers Extron Cable Cubby 800 Cable Access Enclosure wa Extron Show Me Cables Connect the Show Me cables to the source devices Connect the Show Me cables to the switcher Connect the switcher to the display Connect the display to the system controller Connect the system controller to the switcher Connect power to the switcher and system controller This diagram shows the TeamWork 400 system To add a TeamWork VGA kit to the TeamWork system see VGA Show Me Cables on page 9 O TeamWork Kits Installation Guide Continued Show Me Cables The Extron Show Me cables are for use with Extron TeamWork systems They feature a Share button for remote input source selection and a control pigtail which may be wired directly into Extron swi
5. FAX 81 3 3511 7656 FAX 86 21 3760 1566 FAX 971 4 299 1880 FAX 82 2 3444 1575 FAX Inside India Only 1 714 491 1500 1 919 850 1000 31 33 453 4040 91 80 3055 3777 1 714 491 1517 FAX 1 919 850 1001 FAX 31 33 453 4050 FAX 91 80 3055 3737 FAX 2013 Extron Electronics All rights reserved www extron com 68 2400 50 Rev C 12 08 13
6. step 7 to verify that the second source device is providing a video signal and it is the output signal from the switcher When the button on the second Show Me cable is pressed the LED lights blue and the LED on the first cable is switched off 10 Disconnect all the Show Me cables from the source devices After about 30 seconds without an input signal the display should turn off 11 Connect a Show Me cable to a source device and press the Show Me button on that cable As soon as an active video signal is detected the display should automatically turn on Troubleshooting No Image on the Display Cause 1 There is a problem with the source device Solution Verify the source device is powered on and outputs an active signal Cause 2 Cable connections are incorrect Solution Verify the HDMI output cable from the switcher is connected to the current HDMI input of the display Cause 3 Display is off Solution 1 Verify the display is in the on state Solution 2 The TeamWork system turns the display on and off by controlling the AC power If the display has a Sleep Mode feature this feature must be disabled to prevent the display from accidentally powering off Cause 4 The display has a problem Solution Verify that the display functions correctly Cause 5 The display cannot show video at the incoming resolution Solution The EDID settings on the switcher may need to be chang
7. the Cable Cubby Detailed instructions are in the Cable Cubby Setup Guide Extron recommends the layout shown to the right with AAP shelf assemblies on either side of the power modules NOTE Depending on your country a power module may occupy two or three AAP spaces so your final configuration may look slightly different Secure the power modules in position with the provided 4 40 Phillips head screws and star washers WARNING Possible electric shock To ensure good electric grounding you must use the star washers with the screws Install the AAP Shelf Assembly and Show Me Cables INPUT to source device Top of Cable Cubby ATTENTION e The end with the button and LED connects to the input devices and must come out of the top of the Cable Cubby The end with the three conductor pigtail connects to the switcher and must come out of the bottom of the Cable Cubby 1 Assemble the AAP shelf assembly 2 Insert the AAP assemblies into the Cable Cubby from underneath and secure them in position with the provided 4 40 Phillips head screws and star washers NOTE The diagrams on this page show how to install HDMI Show Me cables in the AAP Shelf Assembly If you are using the TeamWork VGA kit install VGA Show Me cables in exactly the same way O 4 Share Button Three conductor pigtail for contact closure and tally Show Me Cable
8. Fa Maea wm Extron Electronics o RG INTERFACING SWITCHING AND CONTROL oro TeamWork Kits e Installation Guide TeamWork 400 and TeamWork 600 Kits The TeamWork 400 and TeamWork 600 kits consist of an HDMI switcher system controller Cable Cubby and cables packaged together as a complete system that in most cases requires no configuration Contact Closure Extron IPL T PC1 System Controller Flat Panel AC Cord RS 232 Control Cable Extron HDMI Pro Cable HDMI Video Extron SW4 HDMI Switcher Flat Panel Display w Integrated Speakers Extron j Cable Cubby 800 a Cable Access Enclosure Extron Show Me Cables The diagram above shows a typical TeamWork 400 application The input devices laptops and a tablet connect to the switcher using Show Me cables The Show Me cables allow the user to select the active input on the switcher A control cable connects the RS 232 ports on the switcher and the system controller The system controller powers the display on and off The system controller has been configured so that when a video signal is detected on any of the switcher inputs the display is powered on A 30 second timer is started when no signal is detected on any of the switcher inputs If an active source is detected before the timer expires the display remains on and the timer is reset If 30 seconds pass without an active signal the sys
9. Work VGA Analog to digital converter 1 RGB HDMI 300 A VGA Show Me cable 1 HDMI cable 1 Installation Guide TeamWork Kits Installation Guide TeamWork 400 and TeamWork 600 Kits seam Work 400 TeamWork 400i TeamWork 600 TeamWork 600i HDMI switcher 1 SW4 HDMI 4 input 1 SW4 HDMI 4 input 1 SW6 HDMI 6 input 1 SW6 HDMI 6 input System controller 1 IPL T PC1 1 IPL T PC1i 1 IPL T PC1 1 IPL T PC1i Cable Cubby 800 1 1 1 1 Power modules 2 US modules included Sold separately 2 US modules included Sold separately 4 AC outlets total 2 AC outlets total 4 AC outlets total 2 AC outlets total HDMI Show Me cables HDMI cable Switcher control cable Cable Cubby AAP brackets 2 pairs 3 pairs 2 pairs 3 pairs three space Cable Cubby AAP brackets 2 pairs 2 pairs two space Cable pass through AAPs right single space Blank AAP plates single space IEC C14 male power cord plug See instructions below Installation Guide TeamWork Kits Installation Guide IEC C14 Male Power Cord Plug Installation When using the IPL T PC1i system controller International TeamWork kits you must replace the power plug on the display with the provided IEC C14 male power cord plug This plug has a maximum current rating of 10 A and a maximum voltage of 250 VAC WARNING High Voltage Failure to follow these instructions may result in serious injury e Installa
10. ed Refer to the SW HDMI Series User Guide see www extron com or contact an Extron Support representative at www extron com company contactus aspx 11 TeamWork Kits Installation Guide Continued Show Me Button LEDs Stay Off When Pressed Cause 1 The cable is not plugged into a source device that is producing an active video output signal Solution Verify that the source device is on and producing an active signal Cause 2 Contact or Tally wiring is incorrect Solution See Show Me Cables page 8 to ensure the contact and tally pins are correctly wired Cause 3 The switcher is not powered on Solution Verify that the switcher is powered on Cause 4 Problem with Show Me cable Solution Try connecting the video source to a different cable If the second cable works correctly there may be a problem with the Show Me cable Contact an Extron Support representative at www extron com company contactus aspx Cause 5 Problem with Switcher Solution If none of the cables work correctly there may be a problem with the switcher Contact an Extron Support representative at www extron com company contactus aspx Cause 6 The source device does not output 5V Solution This is a problem with the source device HDMI specifications require pin 18 to carry a 5V output and VGA specifications require pin 9 to carry a 5V output The Display Does Not Automatically Turn On Cau
11. nector NOTES e Always check and test compatibility before installation Some systems may require advanced configuration of the system controller and require the display to be controlled by RS 232 Ethernet or Infrared e Some displays support a lockout of local buttons Extron recommends that after setup user accessible controls are locked whenever possible This ensures the display remains optimized for the TeamWork system TeamWork systems require a display that returns to the previous state when the power cord is disconnected and then plugged back in When using the IPL T PC1i system controller International TeamWork kits you must replace the power plug on the display with the provided IEC C14 male power cord plug Teamwork Systems work by controlling AC power to the display How to check if a display is compatible Apply AC power to the display Turn the display ON Select the HDMI input Adjust the volume Extron System Controller Unplug the display remove AC power Extron HDMI Switcher 6 Re apply AC power to the display If the display powers back up to the ON state and to the same input and volume level the display will work with the TeamWork system AC Power For Audio Playback display should have integrated speakers a Display should have an HDMI input and support embedded 1080p Native audio Resolution Display Installation Install the Power Modules in
12. on the switcher NOTES e The drain wire does not need to be wired to the switcher The Show Me cables are grounded via the video connectors e Do not connect the Show Me cable to the V pin on the Extron switcher Press the Share button to switch the connected source to the main presentation display Pressing the Share button creates a momentary contact closure which triggers the switcher to select the connected source device If a tally output is available the button will light up blue NOTE The source device provides the 5 VDC supply voltage needed to illuminate the Share button If the source device does not supply this 5 VDC the Share button will not illuminate Some mobile devices do not provide the required voltage to light up the button TeamWork Kits Installation Guide Continued Connect the Switcher to the Display Device Connect the switcher HDMI output to the HDMI input of the display device using the provided cable Do not use HDMI to DVI adapters If necessary see the user guide for the display device Connect the Display to the System Controller Connect the power cord from the display device to the power output receptacle of the system controller TeamWork systems work by controlling the AC power to the display ATTENTION If you are using the IPL T PC1i International TeamWork kits you must replace the power plug on the display with the provided adapter For instructions see page 3
13. se 1 Incorrect wiring Solution Verify that the RS 232 communication cable is connected properly between the IPLink controller and Extron switcher Cause 2 There is no video signal present at Show Me cables Solution Verify that an active signal is present at the input of any of the Show Me cables Cause 3 IPLink configuration is missing or corrupted Solution Contact an Extron Support representative at www extron com company contactus aspx Cause 4 Display power is out of sync Solution The display is in standby mode Turn on the display using the remote or the physical power button Cause 5 Display has sleep mode enabled Solution Go to the menu for the display and disable the sleep mode feature Turn on the display using the remote or physical power button The Display Stays On and Never Turns Off Cause 1 Video signal is present at Show Me cables Solution Verify that no active signals are present at the inputs of any of the Show Me cables The TeamWork system is designed to turn off the Display only when no video signals are present Extron Headquarters Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Extron Korea Extron India 1 800 633 9876 Inside USA Canada Only 800 3987 6673 65 6383 4400 81 3 3511 7655 86 21 3760 1568 971 4 299 1800 82 2 3444 1571 1800 3070 3777 Extron USA West Extron USA East Inside Europe Only 65 6383 4664
14. tact closure which triggers the switcher to select the connected source device If a tally output is available the button will light up blue NOTES e The source device provides the 5 VDC supply voltage needed to illuminate the Share button If the source device does not supply this 5VDC the Share button will not illuminate Some mobile devices do not provide the required voltage to light up the button e Digital Show Me cables support embedded audio and CEC signals VGA Show Me Cables 1 Connect the input end of the VGA Show Me cable to the source device 2 Connect the output of the Show Me cable to the VGA input of the analog to digital converter 3 Connect the HDMI cable from the digital output of the converter to the HDMI input of the switcher Extron HDMI Switcher Extron Analog to Digital Converter SHOW ME CABLE SWITCHER END output Three conductor pigtail for contact closure and tally REMOTE TALLY OUT 123 44V CONTACT RS 232 AUTO Tx Rx Y Yellow SHOW ME CABLE SOURCE END 4 Optional Connect the audio output from the source device to the 3 5 mm TRS audio input on the converter the cable is not provided with the TeamWork VGA kit The audio signal is embedded in the HDMI output signal 5 Connect the Green Tally Out and Yellow Contact pigtail wires as shown above The number under the Tally Out and Contact pins must correspond to the video input
15. tchers with contact closure and tally outputs 1 3 HDMI Show Me cable INPUT OUTPUT to source device to switcher Top of Cable Cubby Bottom of Cable Cubby Share Button Three conductor pigtail for contact closure and tally iT 7J to source device na to converter Top of Cable Cubby Bottom of Cable Cubby Three conductor Share Button pigtail for contact closure and tally HDMI Show Me Cables 1 Connect the input end of the Show Me cable to the source device 2 Connect the HDMI output to the Extron switcher Extron SW4 HDMI Switcher HDMI input INPUTS OUTPUT REMOTE TALLY OUT CONTACT RS 232 AUTO 34G TRV Three conductor pigtail for contact closure and tally SHOW ME CABLE SWITCHER END output Male HDMI connector REMOTE TALLY OUT 12344 CONTACT RS 232 AUTO Tx Rx V Drain wire not used 3 Connect the Green Tally Out and Yellow Contact pigtail wires as shown above The number under the Tally Out and Contact pins must correspond to the video input on the switcher NOTES e The drain wire does not need to be wired to the switcher The Show Me cables are grounded via the video connectors e Do not connect the Show Me cable to the V pin on the Extron switcher Press the Share button to switch the connected source to the main presentation display Pressing the Share button creates a momentary con
16. tem controller powers off the display The TeamWork kits work as described without further software configuration If you need to change the behavior or operation of the system you must configure the system controller see the IPL T PC7 IPL T PC1i User Guide at www extron com TeamWork Kits Installation Guide Continued TeamWork VGA Kit The TeamWork VGA kit adds support for legacy analog computer sources to the TeamWork 400 and TeamWork 600 collaboration systems For fast installation the analog to digital converter RGB HDMI 300 A is pre configured for use with flat panel displays that have a resolution of 1080p If you need to change the behavior or operation of the converter see the RGB DVI 300 and RGB HDMI 300 A User Guide at www extron com VGA Show Me Cable Contact Closure and Tally Features Standard systems support groups of up to four TeamWork 400 or six TeamWork 600 users Standard systems contain a complete turnkey package that includes cables switcher system controller and Cable Cubby enclosure System controller pre loaded with Global Configurator that requires no further adjustment Works with most commercially available flat panel displays laptops and tablets HDCP compliant Supports legacy analog sources with optional TeamWork VGA kit Section 508 compliant Kit Components When your kit is delivered check that all the components are present TeamWork VGA Kit Team
17. tion and service of the power cord plug must be performed by authorized personnel only e Observe the correct wire polarity e Before installation disconnect the display from the power source or any other device NOTE The power cord plug shown in the figure is for illustration only The plug provided may not look exactly the same 1 Cut the existing plug from the LGN power cord 2 Remove a suitable amount of the outer sheath from the power cord Individual wires should not extend from the back of the strain relief after the plug is installed 3 Strip a suitable amount of the jacket from the three wires There should be just enough bare metal to wrap around the screw in step 7 Ground p Earth Neutral 4 Loosen the screw and remove the top plate If required loosen the white plastic wire clamp Thread the cord through the strain relief Use a flat head screwdriver to secure the individual wires to the correct connector WARNING Observe the correct wire polarity see the diagram to the left Live Hot Secure the wires by tightening the white plastic wire clamp Reattach the top plate and screw that were removed in step 4 TeamWork Kits Installation Guide Continued Display Requirements The TeamWork system is designed to work with most brands and models of flat panel displays available worldwide For optimum performance consider the following when selecting the displa
18. ys for your TeamWork installation The display should be tested thoroughly prior to installation or mass deployment of TeamWork systems Power attributes The system works by controlling AC power to the display When the display is in the ON state with an HDMI input selected it must be able to power back ON to the same HDMI input when AC power is disconnected and reconnected If the display doesn t behave this way an alternate display should be used Alternatively you may need to control the display a different way i e RS 232 infrared or via Ethernet using a different type of Extron control processor Sleep mode if the display has a Sleep Mode feature Sometimes called auto sleep it must be disabled Many displays have an option to disable this within the menu settings Resolution The TeamWork systems were designed for use with flat panels having an HDMI input connector and having a native resolution of 1080p Many of the readily available consumer and professional displays support 1080p natively Audio Audio from source devices is supported in the TeamWork system by routing it as an embedded audio signal to the display for playback via integrated speakers Most displays with HDMI inputs and integrated speakers work this way Some professional or commercial grade displays do not have integrated speakers and will not Support audio playback Typically source devices with HDMI output connectors embed audio onto the HDMI con
Download Pdf Manuals
Related Search