Extron electronic Extron Electronics Stereo Receiver RGB 203 RXI User's Manual
Contents
1. E are factory installed Setting 0 is for user recorded and can only be used if a value has been stored at that location see the previous section User Recorded EDID Rotary Switch Resolution Position User recorded EDID 800x600 1024x768 default 1280x720 1280x768 1280x800 1280x1024 1360x768 1366x768 1400x1050 1440x900 1600x1200 1680x1050 1920x1080 1920x1200 Local monitor pass through 2 3 4 5 6 7 8 9 A B C D E F 4 Power on the display device 5 Power on the source device RGB 203 Rxi Setup Guide Continued Local Monitor Pass through EDID To use local monitor pass through EDID 1 If you have not already done so connect the RGB 203 Rxi to the source device Do not switch on the source device at this time 2 Set the rotary switch to position F 3 Ifyou have not already done so connect a monitor to the Local Monitor output and power on that monitor and interface 4 Power on the remote display device 5 Power on source device Operation Level boost Use this knob to alter picture brightness Peak Use this knob to alter picture sharpness Centering controls Use these knobs to center the image on the screen vertically or horizontally lt LCD display When the centering controls are being used this display shows centering information At other times it shows scan rate Input selection This three way switch selects among in2. that can be used By default the EDID value is set to a resolution of 1024x768 which will allow most source devices to boot up and provide a signal that can be displayed Alternatively you can record your own EDID information and use those values or use EDID information from a monitor connected to the Local Monitor output User Recorded EDID You may also record EDID information from a specific monitor as follows 1 Connect a display to the Local Monitor output and power on the monitor and interface 2 Turn the EDID Select dial to setting 0 3 Press and release the recessed Record button The LED light will flash red slowly three times while the EDID is recorded and return to green when recording is complete NOTE This EDID will be stored in memory until deleted or overwritten Using Recorded EDID Values NOTE To boot up correctly the source device must be able to receive EDID information during the boot process Therefore the interface and the local monitor if using pass through EDID must be switched on before the source is switched on Use factory installed EDID information or the user recorded EDID as follows 1 If you have not already done so connect the RGB 203 Rxi to the source device Do not switch on the source device at this time 2 Set the left front panel DIP switch to the required frequency 50 or 60 Hz 3 Set the rotary switch to the required value see the table below Settings 1
3. Internal Configuration RGB 203 Rxi Setup Guide These instructions provide a quick setup guide for the Extrone RGB 203 Rxi interface Installation and service must be performed by authorized personnel only There are two RGB 203 Rxi models one with EDID Minder and one with ADSP Unless otherwise stated all instructions refer to both models Step 1 Configure sync settings Turn off all equipment and disconnect the mpar power sources Remove the cover from the interface and locate jumper blocks J6 J7 J20 and J11 as shown at right CAUTION Only authorized service personnel should perform changes to J7 V Sync 3 internal jumpers Take steps to prevent electrostatic discharge J6 H Sync ee ee ees J20 Sar ync 3110 B Set output sync to follow input sync remove the jumper from J20 Set vertical sync for negative V sync remove jumper from J7 for positive V sync install jumper on J7 Set horizontal sync for negative H sync remove jumper from J6 for positive H sync install jumper on J6 Clamp sync timing to back porch place jumper between pins 1 and 2 on J11 Clamp sync timing to sync tip place jumper between pins 2 and 3 on J11 Mounting Step 2 Mount interface Choose a suitable place to mount the interface see the RGB 203 Rxi User Guide for details Rear Panel Connections Both RGB 203 Rxi interfaces have identical rear panel connections Connect but do not power on input and o
4. USA Canada Inside USA Canada Inside Europe Only Inside Asia Only 81 3 3511 7656 FAX Inside China Only 971 4 2991880 FAX Only Only 31 33 453 4040 65 6383 4400 86 21 3760 1568 68 655 51 1 714 491 1500 1 919 863 1794 31 33 453 4050 FAX 65 6383 4664 FAX 86 21 3760 1566 FAX Rev A 1 714 491 1517 FAX 44 919 863 1797 FAX 11 10 2010 Extron Electronics All rights reserved www extron com
5. de Continued Step 8 Connect RS 232 Controller Connect an RS 232 2 1 Pin RS 232 Contact Closure Function controller to this DB9 connector for remote control For ol 1 Ln SUN iL Inputa correct wiring see the diagram and table at right 3 6 2 Ve Transmit data Female 3 Rx Receive data 1 5 4 Input 2 Input 2 e e 5 Gnd Gnd Signal ground 6 Input 3 Input 3 aie 7 8 9 Not used Rear Panel DIP Switch Configuration Step 9 Set Rear Panel DIP Switches Configure the rear panel DIP switches as shown in this table Switch Effect Switch Effect O Down ADSP Down Monitor tied to in 1 ID bits unterminated gt mp mal a Down RGBHV or RGBS output Down Stereo audio Serration pulses Autoswitch to highest input number with sync signal present Down No serration pulses Down Autoswitching off Jobunlundevyncouse Downltepbactighton Down Wide V sync pulse Down LCD backlight on Step 10 Connect Power Connect a standard IEC AC power connector 100 240 VAC 50 60 Hz to this socket Extron RGB 203 Rxi with apsp LEVEL PEAK S PR 1 ee 98 BO ST CON ROL vy 10 Extro LEVEL BOOST CONTROL RGB 203 Rxi Setup Guide Continued Configuring EDID EDID Minder Model Only The Extron EDID Minder ensures the resolution of the video source signals are compatible with the display devices The RGB 203 Rxi provides 14 factory installed EDID values
6. puts The corresponding LED lights Troubleshooting No response to 4 or lt gt centering controls e DDSP is in use Set DIP switch 1 on the rear panel to Off e Front panel security lockout disables centering Disable front panel security lockout see RGB 203 Rxi User Guide No response to switching controls e Front panel security lockout disables switching Disable front panel security lockout see RGB 203 Rxi User Guide If the image does not appear or is incorrectly displayed e Ensure that all devices are plugged in and receiving power The front panel LCD of the interface lights if the interface is receiving power and an active sync signal Check the cabling and the audio connector wiring and grounding and make adjustments as needed e If using the model that has the EDID Minder make sure the rotary dial and frequency DIP switch are set to the correct values If these settings are changed reboot the source device e If using the model that has the EDID Minder make sure the video output device can support the resolution provided by the EDID Minder If necessary reset the rotary dial and reboot the source device NOTE See the RGB 203 Rxi User Guide for a complete troubleshooting guide Extron USA West Extron USA East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Headquarters 800 633 9876 800 633 9876 800 3987 6673 800 7339 8766 81 3 3511 7655 400 883 1568 971 4 2991800 Inside
7. utput devices 100 240 0 2A ae eee le UL OUTPUTS __ Moh FR INP IT 2 MON TOR 8 Step 3 Connect Video Inputs Connect an RGBHV RGBS RGsB or RsGsBs video input to each 15 pin HD connector as desired CE Step 4 Connect Audio Inputs Connect an unbalanced stereo audio source to each 3 5 mm mini tip ring sleeve TRS stereo audio connector for unbalanced audio input as desired Wire the connector as shown in the figure at right RGBHV Video Step 5 Connect Local Monitor If required connect a monitor to this 15 pin HD connector Step 6 Connect Video Output Connect the RGBHV RGBS or RGsB video display to the output o 6 9 connectors as shown in the figure at right Step 7 Connect Audio Output Connect an audio device to this 3 5 mm 5 pole captive screw connector for balanced or unbalanced audio output For correct wiring see the diagram below RGsB Video mind xx X CAUTION For unbalanced audio connect Tp A EH Lett Tip EEEo AL EH Let the sleeves to the center ie get HERE Q ify te P ak ss S e E OH te eeve s Mo f k eeve s M uF contact ground Tip gt QE S E aight Tip OFS E pict DO NOT connect the sleeves NO GROUND HERE Q 4 if Ig Ring Ss QE ai fy ng to the negative contacts Unbalanced Stereo Output Balanced Stereo Output RGB 203 Rxi Setup Gui
Download Pdf Manuals
Related Search