Extron electronic Extron Electronics Projector Accessories PMK 450 User's Manual
Contents
1. Extron Electronics INTERFACING SWITCHING AND DISTRIBUTION Q SER b suo s 6 curio Installation Notes for PMK 450 70 618 03 Front Plate 1 The Extron PMK 450 Projector DPE Mounting Kit can accommodate multiple Extron products of one eighth quarter or half rack sizes with power supplies The components of the PMK 450 kit are shown in Figure 1 Also included are e Set screw hex wrench 1 e Security screw hex wrench 1 e Velcro Pads for securing power supply 2 e 4 40 Screws for mounting devices 6 Bottom Plate 1 Filler Plate 1 Figure 1 Contents of PMK 450 kit Installation oF TALON Maximum load for the PMK 450 is 15 Ib 6 8 kg 1 Unscrew the front and rear plates and the security screws from the sides Slide the top and bottom plates apart The filler plate is attached to the rear plate and should not be removed 2 Ensure that the mounting pipe is installed with the cable access hole facing the rear away from the projector screen 3 Loosen the four pipe collar set screws to allow the top plate to move freely along the pole 4 Slide the top plate up the pipe until the pipe collar is positioned just above the cable access hole Figure 2 Ensure the rear of the top plate is facing to the rear in the same direction as the cable access hole in the pipe 5 Level the top plate and secure it by fully tightening the set screws At least three screws must com2. e in contact with the pipe 6 Route the cables so that they exit the pipe via the cable access hole Figure 3 Cable A abie ACCe SS 7 Using the supplied 4 40 screws secure the devices Hole to the bottom plate Figure 3 shows the PVS 204 screwed to the plate with a power supply attached by the supplied Velcro pads 8 Attach cables to the device s and pull excess cable back into the ceiling Feed the output cables to the projector via the cable access hole and the bottom of the pipe Pipe Collar 1 with Set Screws 4 AC Power Cord Access Slot Screws 4 Pipe Collar amp Set Screws Cable Input from Sources AV control Bottom Plate Cable Output to Projector Figure 3 Route cables 68 1397 01 Rev B 11 07 PMK 450 Projector Mounting Kit Installation Notes 1 PMK 450 Installation Notes cont d 9 Insert the lugs on the bottom plate into the slots on the top plate and slide the bottom plate into position Figure 4 10 Lock the top and bottom plates together with the security screws pass the AC power cord through the slot at the rear of the top plate 11 Reattach the front and rear plates Figure 5 Figure 5 Attach front and rear plates Specifications DONEN SIONS eiio 2 25 5 72 0m H x 12 25 2 00 DIA 50 80 mm 31 12 cm W x 11 63 29 53 S cm D Mount application Mounts to standard 1 5 3 8 cm NPT pi
3. pes or pipes with external diameters of Unk 11 63 1 85 4 7 cm to 1 95 5 cm 295 30 mm Material eeeeeseeeeeeeeeeeeee White powder coated l aluminum Maximum IORI saves sorccessoenextanemeein e 15 1b 6 8 kg Product weight aosarcinsssioisros 2 35 lbs 1 07 kg NAPPING Wep Mieris 3 lb 1 36 kg 12 25 311 15 mm TSW eenn EE UL CUL as an accessory for r ee use with UL listed mount and projector Comp Han E eee een een ten eee CE VIDEAT OT casssaepigstatacatoccedacsnsaateyacgien ISTA 1A in carton International Safe Transit Association VT i Oy TE E 3 years parts and labor Figure 6 Dimensions yO Bes Extron Electronics USA Extron Electronics Europe Extron Electronics Asia Extron Electronics Japan 9 1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Rd 04 01 Kyodo Building 16 Ichibancho Anaheim CA 92805 3821 AH Amersfoort The Netherlands PM Industrial Bldg Singapore 368363 Chiyoda ku Tokyo 102 0082 eyo 800 633 9876 714 491 1500 800 3987 6673 31 33 453 4040 800 7339 8766 69 6383 4400 Japan wowwiexteoncom FAX 714 491 1517 FAX 31 33 453 4050 FAX 69 6383 4664 81 3 3511 7655 FAX 81 3 3511 7656 2007 Extron Electronics All rights reserved 2 PMK 450 Projector Mounting Kit Installation Notes
Download Pdf Manuals
Related Search