EverFocus EQ150 User's Manual
Contents
1. Lens Mount To mount an appropriate C mount or CS mount lens 3 Locking Screw Use the locking screw to fix the focal length 4 Lens Connector 4 pin socket To connect to the lens plug of the auto iris lens 5 Control Switches There are 6 control switches located on the sideboard which are for the setting of the special features The switches in orders are for Flickerless Back Light Compensation Electronic Shutter Automatic Gain Control Line Lock and Auto Iris Lens type FL Flickerless Function On Normal When picture flicker fiercely turn FL on then the camera will stabilize the speed of electronic shutter at 1 100 EIA or 1 120 CCIR automatically and reduce the flicker immediately The default setting is Normal BLC Back Light Compensation On Normal When BLC is turned on the AGC ES and IRIS operating point is determined by averaging over the center area instead of entire field of view so that a dimly lit foreground object at center area can be clearly distinguished from brightly lit backgrounds BLC should not be used unless it is needed to compensate for back lit The default setting is Normal ES Electronic Shutter Off On ES ON The camera continuously adjusts the shutter speed from 1 60 EIA 1 50 CCIR second to 1 100 000 second according to the luminance conditions of the scene ES OFF The shutter speed is fixed at 1 60 EIA 1 50 CCIR second Set ES OFF when auto iris lens is used or flicker is o2. do focal length adjustment as following i Loosen the locking screw of the focal length adjustment ring ii Take picture of subject at a distance more than 20m away from the camera iii Rotate the focal length adjustment ring to bring the subject in focus iv Tighten the locking screw while the adjustment is completed EverFocus Electronics Corp Head Office 12F No 79 Sec 1 Shin Tai Wu Road HstChi Taipei Taiwan TEL 886 2 26982334 FAX 886 2 26982380 http www everfocus com tw USA Office 2445 Huntington Drive San Marino CA 91108 U S A TEL 1 626 844 8888 FAX 1 626 844 8838 Toll free 1 888 383 6287 or 1 888 EV FOCUS http www everfocus com Hong Kong Office Room 0 10 F Block 3 Camelpaint Building 60 Hoi Yuen Road Kwun Tong Kowloon Hong Kong TEL 852 2758 9871 FAX 852 2758 9056 European Office Albert Einstein Strasse 1 D 46446 Emmerich Germany TEL 49 2822 9394 0 FAX 49 2822 939495 http www everfocus de EverFocus P N MQ15G00100
3. lt 1 3 High Resolution B W Digital Camera User s Manual and Operation Instructions Notice This manual is presented to the users of HQ150 by EverFocus Electronics Corp With years of engineering researches EverFocus has spared no effort to provide the high quality products to the worldwide users For the policy of continual product improvement EverFocus reserves the right to make changes to the product specifications and documentation without notice All the components of the products including accessories components and outlook are based on the agreements of each deals to satisfy all kinds of users Meanwhile please be advised that every step of operation must follow the instruction of this manual to keep EQ150 working under the best condition Please notice that EverFocus will not be charged any claims or renewing cases resulted from inappropriate operation Table of Contents Safety WAITING sans seen Dies TUT ODUCT ON od aa aleee Speci ieat On orien a EEEE Major Parts and Their Functions 222222s0ee 000 4 Installation INStructions ccccceccecccccccceccscssceecs 8 Safety Warning 1 Handle the camera with care Be careful when handling the camera do not drop it or subject it to strong shock or vibration to prevent any damages to it Do not disassemble it or place it on an unstable base 2 Do not install the camera near electric or magnetic fields Installed the camera away from TV
4. al Signal Processing circuitry design that delivers excellent picture quality and performance Nide range automatic electronic shutter 1 60 1 50 1 100 000 sec x Auto line lock with external phase adjustment essed with either C mount or CS mount lenses and easy back focus a Adjustment System available in EIA or CCIR Pickup Device Picture Element Horizontal resolution Sensitivity S N ratio Electronic shutter Auto Iris Flickerless Back Light Comp Electronic Shutter Auto Gain Control Line Lock Audio Gamma Correction Video output Sync Mode Lens Mount Power source Dimension Operating Temperature Power Consumption Specification 1 3 inch interline transfer B W CCD 768x494 EIA 752x582 CCIR 560 TV lines 0 01 lux F 1 2 Over 48 dB 1 60 1 50 1 100 000 sec Video Direct Drive switch On Off On Off On Off On Off On Off Yes gt 0 45 1 0Vp p 75 ohm BNC 1 Line Locked with LL on 2 Internal Sync With LL off C CS mount back focus adjustment 90 260V AC EQ150 12VDC 24VAC EQ150A 51x57x140 2mm 0 C to 50 C SW max Major Parts Names and Their Functions 777 Rear E0150 Rear EQ150A 1 Focal Length Adjustment Ring Use this ring to adjust the appropriate focal length according to the type of lens Rotate the ring clockwise for the CS mount lens rotate it counterclockwise for the C mount lens The factory setting is C mount 2
5. bserved under a very bright fluorescent lamp Otherwise turn ES on for optimum performance The default setting is ON AGC Automatic Gain Control Off On AGC ON The sensitivity increases automatically when light is low AGC OFF A low noise picture is obtained under a low light condition The default setting is ON LL Line Lock Off On To select the sync mode between Internal Sync LL off and Line Lock LL on Set the line lock off the camera will synchronize to the internal time base Set the line lock on the camera s vertical synchronization can be driven by the AC signal in the power lines Note Line Lock sync mode operation is possible only when used with an AC power source it s not possible with a DC power source N VD DD Auto Iris lens Type For video drive auto iris lens please set switch to VD For direct drive iris lens set switch to DD The default setting is DD Wire the cable of lens to lens connector according to the following table Pinl Pin __Pin3 _ _Pind Lens Connector Video Drive 12V GND _ VD IRIS GND i fea 3 Direct Drive Cnt Cnt Drv Drv u ja IRIS Level Control Brightness Level can be adjusted from the IRIS level VR while using the direct drive lens ss Turn counterclockwise to L to get darker picture ss Turn clockwise to H to get brighter picture V Phase Adjustment Screw The vertical phase may require adjustment to synchronize the vertical phase of the camera with
6. other camera in the system when it is to be used in the line lock sync mode Make the adjustment when the vertical phase of the camera does not match with other cameras Mounting Base and Fixing Screws To use when the mounting bracket is required while mounting the camera The mounting base can be attached to either the top or the bottom of the camera fix the mounting base onto the camera by using the 4 supplied fixing screws Video Output Connector BNC VBS 1 0 Vp p 75ohm 10 Audio Out Connector 11 Power Cable EQ150 12 DC12V AC24V Screw Terminals EQ150A 7 DD e Go Nn J 00 Installation Instructions Remove the cover cap from the top of the lens mount To attach a C mount CS mount lens turn the focal length adjustment ring to the appropriate position Note If a C mount lens is used please make sure the focal length adjustment ring is set at C position before fixing the lens Screw the lens firmly onto the lens mount Insert the lens plug in the lens connector if the auto iris lens is used Tighten the locking screw Connect the video output of the camera to a color monitor or other video device through a 75 ohm type coaxial cable with BNC female connector Plug the power cord to the outlet Once the image appears on the monitor adjust the focus and diaphragm of the lens to obtain the best picture If the subject is not in focus when adjusting focus of lens
7. radio transmitter magnet electric motor transformer audio speakers because the magnetic fields generate from above devices will distort the video image 3 Do not install the camera in the high temperature environment Installed the camera away from stoves or other heat generating devices as the high temperature could cause deformation discoloration or other damages of the camera Install the camera at where the temperature range will stay between 0 C to 50 C 32 F to 122 F 4 Never face the camera toward the sun Never aim the camera at the sun or other extremely bright objects whether it is in use or not 5 Cleaning Do not touch the surface of CCD sensor by hand directly Use a soft cloth to remove the dirt from the camera body Use lens tissue or a cotton tipped applicator and ethanol to clean the CCD sensor and the camera lens When the camera is not in use put the cover cap on the lens mount Introduction The new EQ150 series is a solid state B W video camera specially designed for high quality surveillance applications It incorporates break through DSP technology that provides most reliable and accurate B W picture in security industry The camera is convenient to use with C mount or CS mount lenses and has an easy back focus adjustment help to achieve installation efficiency Main Features 4 3 B W CCD pick up device for more than 560 TV lines of horizontal resolution ophisticated DSP Digit
Download Pdf Manuals
Related Search