Euro-Pro IR410 User's Manual
Contents
1. cord is absolutely necessary use a 13 ampere cord Cords rated for less amperage may overheat Use care to arrange the cord so that it cannot be pulled or tripped over 7 Do not operate iron with a damaged cord or after the iron has been dropped or damaged in any manner To avoid the risk of electric shock do not disassemble the iron Return the iron to EURO PRO Operating LLC for examination and repair Incorrect POLARIZED PLUG This appliance has a polarized plug one blade is wider than the other As a safety feature this plug will fit into a polarized outlet only one way If the plug does not fit fully into the outlet reverse the plug If it still does not fit contact a qualified electrician Do no attempt to defeat this safety feature SAVE THESE INSTRUCTIONS For Household Use Only 1 Rev 04 02A Model IR410 LIMITED WARRANTY EURO PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one 1 year from the date of purchase The liability of EURO PRO Operating LLC is limited solely to the repair or replacement of the product at EURO PRO Operating LLC s option This warranty does not cover damage caused by misuse negligence use on improper current or voltage use contrary to operating instructions or disassembly repair or alteration by any person other than EURO PRO Operating LLC Product repair or replacement at our option is your sole remedy This warrant2. 120V AC polarized electrical outlet Do not use any other type of outlet DRY IRONING All marked settings on the temperature dial can be used for dry ironing Slide the variable steam control lever all the down as shown in Figure 1 This will cut off the steam flow if water is in the tank For Dry Ironing Figure 1 1 Turn temperature dial to MIN and slide the variable steam control lever all the way down to 0 2 Plug the cord into a polarized 120V AC electrical outlet The power ON light will come on indicating that the iron is receiving power 3 Turn the temperature dial to the desired setting See Ironing Guide for a guide to temperature selection 4 Place iron on its heel on a stable protected surface while iron is warming to desired temperature STEAM IRONING WARNING DO NOT aim iron at face towards yourself or anyone else while using or adjusting steam Burns or serious injury may occur WARNING Before filling the iron with water be sure the iron is not plugged into the electrical outlet The iron may be filled with water while it is hot WARNING TO PREVENT THE RISK OF BURNS use caution when filling iron with water Burns can occur from touching hot metal parts hot water or steam NOTE Because of the soleplate design ordinary tap water may be used with this iron However in very hard water areas we recommend using distilled or demineralized water CAUTIO
3. N Never fill the iron with fabric conditioner starches or any other liquid as these will damage the steam mechanism Do not use contaminated water 19 1 Turn temperature dial to ee or eee and slide lever all the way to the left 2 Holding the iron at a slight angle pour water slowly into the water filling inlet See figure 2 Fill tank to desired level or to the MAX water level marking using the water filling flask When the iron is upright the blue see through water tank allows you to gauge the amount of water DO NOT overfill the tank Figure 2 3 Plug the cord into a polarized 120V AC electrical outlet OPERATING INSTRUCTIONS CONT 4 Turn the temperature dial to any of the temperatures within the gray steam band and allow the iron to heat for approximately 2 minutes before ironing Place iron on its heel on a stable protected surface while the iron is warming to desired temperature 5 Slide the steam lever up to increase the amount of steam When using extra steam the iron uses more water and it may be necessary to fill the tank more often See page 4 Figure 3 6 Steam is produced as soon as the iron is held in the horizontal position Steam will stop coming out when the iron is put on its heel in a vertical position or by turning the steam control dial to 0 BURST OF STEAM WARNING DO NOT aim iron at face towards yourself or anyone else while using or adju
4. OO iQGSNOUl 38 LONNVD ATOILYV SIHL sue w j qej y uo y jey 30u se jd Technical Specifications Voltage 120V 60HZ Power 1200 Watts USER MAINTENANCE INSTRUCTIONS EMPTYING THE IRON 1 Always empty iron after each use 2 When finished using the iron turn the variable steam control to O and the temperature control dial to MIN 3 Unplug the iron from the electrical outlet 4 Set variable steam control to MAX 5 Turn the iron upside down over the sink with the tip pointing downward and allow the water to flow from the Opening 6 Set variable steam control to O 7 Allow iron to cool in an upright position before storing WARNING Use caution when emptying the iron Burns may occur from touching hot metal surfaces hot water or steam STORAGE 1 Always turn the variable steam control to O after you have emptied the water tank Allow the iron to cool down Always store the iron in the upright position to protect the soleplate From time to time clean the exterior of the iron with a damp cloth and wipe dry If you use spray starch wipe the soleplate occasionally with a soft damp cloth to prevent the build up of deposits If the iron has not been used for a few weeks hold the iron horizontally and allow to steam for 2 minutes before ironing OPERATING INSTRUCTIONS This appliance is for HOUSEHOLD USE ONLY and may be plugged into any
5. OWNER S MANUAL Craft iron Model IR410 For information or assistance EURO PRO Operating LLC 21 Lawrence Paquette Industrial Drive Champlain NY 12919 www euro pro com EURO PROX IMPORTANT SAFETY INSTRUCTIONS When using your iron basic safety precautions should always be followed including the following g reassembly can cause the risk of electric shock when the iron is used Close supervision is necessary for any appliance being used by or near children Do not leave iron unattended while connected or on an ironing board 1 Read all instructions carefully 2 Use iron only for its intended use 3 To protect against risk of electrical shock do not immerse the iron in l water or other liquids Always turn 9 Burns can occur from touching hot the iron to OFF before plugging in metal parts hot water or steam Use or unplugging from outlet caution when you turn a steam iron upside down there may be hot 4 Never yank cord to disconnect from water mnihe receo outlet Grasp plug and pull to i disconnect 10 This appliance is for household use only 5 Do not allow cord to touch hot y surfaces Let iron cool completely before putting away SPECIAL INSTRUCTIONS 1 To avoid a circuit overload do not operate another high wattage appliance on the same circuit 6 Always disconnect iron from electrical outlet when filling with water emptying or when not in use l l 2 If an extension
6. ater e Make sure that the temperature control dial and the variable steam control are correctly set For maximum steam setting Max on steam control temperature control dial should be set on eee e Adjustable steam control is set on 0 Always allow the iron to reach the selected temperature with the adjustable steam control setting at 0 Make sure the temperature control dial is set in the correct steam area e g and the steam control is not on 0 For more steam turn temperature dial to higher setting e g and the steam control to Max e If temperature setting and steam control setting are correct and there is no steam gently tap the soleplate on the ironing board a few times Move the variable steam control from 0 to Max a few times e Iron may not be hot enough Set thermostat to the Max position Always allow iron sufficient time to heat up thermostat light goes off before activating the variable steam control e Overuse of steam burst Allow more time between each burst e Iron may have been overfilled Turn iron off empty water and follow instructions for filling e Steam performance may be low if iron requires seasoning To season use regular tap water for 1or 2 tanks until steam performance improves ADDITIONAL IMPORTANT SAFEGUARDS 11 Always store your iron on the iron rest provided with your iron not on the soleplate If stored face down ev
7. en the smallest amount of moisture will cause the soleplate to corrode and stain 1 Do not rest iron on soleplate 2 Never use or rest iron on an unstable surface 3 While the iron is hot never set iron on an unprotected surface even if it is on its heel rest 4 WARNING TO PREVENT ELECTRIC SHOCK OR OTHER INJURY before filling the iron with water make sure that the plug is removed from the outlet 5 CAUTION Never fill the iron with fabric conditioner starches or any other solution as these will damage the steam mechanism Do not use contaminated water 6 WARNING TO AVOID FIRE never leave iron unattended while it is plugged in 7 WARNING TO PREVENT ELECTRIC SHOCK never immerse the iron in water or other liquid 8 WARNING TO PREVENT ELECTRIC SHOCK never use the iron in a location where it can fall or be pulled into water or any other liquid If the iron falls into water or any other liquid unplug it immediately DO NOT reach into the water or liquid 9 CAUTION Never use scouring pads abrasive or chemical cleaners or solvents to clean the exterior or soleplate of your iron Doing so will scratch and or damage the surface 10 WARNING DO NOT aim iron at face towards yourself or anyone else while using or adjusting steam Burns or serious injury may occur 12 DANGER Never use the iron if it is damaged or dropped Using the iron when it is damaged could create the risks of fire elec
8. ntrol Dial Figure 6 Variable Steam Control Figure 7 NOTE Before starting to iron delicate fabrics it is best to first test the temperature of the iron on a hem or an inside seam IRONING HINTS WARNING To prevent fire do not leave iron unattended while connected e Sort articles to be ironed according to the type of fabric This will reduce the need to adjust the temperature for different types of garments e If you are not sure of the fiber content of a garment test a small area such as a seam or inside hem section before ironing a visible area Start with a low temperature setting and gradually increase to find the best setting e When reducing the temperature to iron sensitive fabrics allow approximately 2 minutes for the iron to cool to the new temperature setting e Fabrics such as velour wool linen and silk are best ironed with an ironing cloth to prevent shine marks
9. se complete and return within ten 10 days of purchase The registration will enable us to contact you in the event a product defect is discovered By returning this card you acknowledge to have read and understood the instructions for use and warnings set forth in the accompanying instructions RETURN TO EURO PRO Operating LLC 21 Lawrence Paquette Ind Dr CHAMPLAIN N Y 12919 BURCHA SER eni a a aCe ene a E ee eee ae ee eee 7D 2 21 Zoho a Te aN eR EAE ae eR Ce te ee ee ee DATE OF PURCHASE ccccceeeceeeseeeees MODEL Model IR410 SERIAL NO ooa NAME AND ADDRESS OF STORE seda A AEE eee adi quises rea NS TROUBLESHOOTING PROBLEM POSSIBLE REASONS amp SOLUTIONS lron does not heat Thermostat ready light goes On and Off Some odor or small particles come out of steam vents of new iron Iron does not steam Water droplets coming from steam vents Printed in China e Iron should be plugged into a 120V AC electrical outlet only Make sure that the plug is securely in the socket e Temperature setting too low Turn to higher setting e This is normal The light goes On and Off as the thermostat is switching the heating element On and Off to maintain the selected temperature e This is normal Follow instructions for first use and allow iron to steam through 2 3 fillings amp press the steam burst button occasionally to eliminate small white particles e Water tank may be empty or water level is very low Add w
10. sting steam Burns or serious injury may occur The burst of steam button is useful when ironing denim cotton and linens It provides extra sudden blasts of steam which aid in removing stubborn wrinkles The burst of steam feature can be used with Dry or Steam ironing as desired 1 Make sure the water tank is at least 1 2 filled with water 2 Set the temperature dial Place the iron on the stand on a stable protected surface and allow it to heat for approximately 2 minutes 3 With the iron in a horizontal position press the burst of steam button several times to prime the pump See Figure 4 Figure 4 NOTE If the tank runs dry remove the plug from wall outlet Then fill the iron with water and re prime the pump The iron may be filled with water while it is hot WATER SPRAY The water spray is useful on fabrics with stubborn wrinkles Press the spray button and a jet of water will spray onto the fabric being ironed See Figure 5 The water spray can be used with dry or steam ironing as desired Figure 5 OPERATING INSTRUCTIONS CONT SELECTING IRON TEMPERATURES Always read garment labels and follow the manufacturer s ironing instructions Refer to the Ironing Chart on page 10 for temperature recommendations e Use low settings for synthetics ee Use moderate settings for wool silks and blends eee Use high settings for cottons and linens Temperature Co
11. tric shock injury or death GETTING TO KNOW YOUR IRON Before using your Craft Iron remove any labels stickers or tags that may be attached to the body or soleplate of the iron When turned on for the first time your new iron may emit an odor for up to 10 minutes This is due to the initial heating of the materials used in making the iron The odor is safe and should not reoccur after initial heating Also before ironing with steam for the first time allow iron to heat hold in a horizontal position and hit the burst of steam button several times The iron may emit some small particles from the steam holes This is normal and will clear after pressing the burst of steam NOTE Before starting to iron delicate fabrics it is best to first test the temperature of the iron on a hem or an inside seam IRONING CHART To select iron temperature align temperature selected on dial with the indicator on the water tank button several times Ga Sault o DA 2 aE x FIBERS e g m fi i FABRIC ied acrylic nylon COTTON J a polyester LINEN ZININ ae J TEMP MAX 2 CONTROL i 7 STEAM MINIMUM MAXIMUM i SS CONTROL STEAM STEAM SS P 4 Va N ad a BURST OF SPRAY Variable Steam Control Water Inlet Spray Nozzle Water level indicator 1 Temperature control dial 2 Temperature ready light 3 Spray button 4 Burst of Steam Button
12. y excludes all other legal and or conventional warranties The responsibility of EYURO PRO Operating LLC if any is limited to the specific obligations expressly assumed by it under the terms of the limited warranty In no event is EURO PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever Some States do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This warranty gives you specific legal rights which vary from state to state If you have a claim under this warranty or if you require service DO NOT RETURN THIS PRODUCT TO THE STORE Send the product postage prepaid to In U S A EURO PRO Operating LLC 21 Lawrence Paquette Industrial Drive Champlain NY 12919 Tel 800 798 7398 Please include a copy of your sales receipt 9 50 to over the cost of return shipping amp handling and a letter explaining the nature of your difficulty Do not forget to enclose your name address and telephone number If the warranty period has expired please send your iron postage pre paid to In U S A Service Department EURO PRO Operating LLC 21 Lawrence Paquette Industrial Drive Champlain NY 12919 Tel 800 798 7398 You will be advised of the cost of repair before any servicing is done unless you enclose a note indicating that you would like us to proceed with the repairs and return the iron to you C O D E ae PRODUCT REGISTRATION CARD Plea
Download Pdf Manuals
Related Search