Epson T3000 Setup Guide
Contents
1. cartridges Basket holders Plastic connector Basket arms Stack guide 7 2 SureColor T3000 NE 3 SureColor T5000 lt SureColor T7000 3 x8 1 square pole and 1 rounded pole Assembling the Stand 1 Unpack the stand and make sure you have all of these items 4 Assembling the Stand 2 Slide the horizontal strut into both of the legs as shown 3 Use the long end of the hex wrench to tighten the pre placed screws on each side of the horizontal strut Mounting the Printer on the Stand 5 Mounting the Printer on the Stand You need at least two people SureColor T3000 or four people SureColor T5000 T7000 to install the printer and position it on the stand When lifting the printer only hold the areas shown below Otherwise damage may occur SureColor T3000 Caution Before installing the printer lock the casters to make sure the stand is fixed in place 1 Lift the printer onto the stand Line up the marks on the bottom of the printer with the arrows on the top of the stand legs before setting the printer down 6 Attaching the Paper Basket 2 Attach the printer to the stand using three bolts Attaching the Paper Basket The paper basket is a cloth sheet that attaches to the printer stand and catches your prints as they come out You need the following parts to assemble and attach the paper basket 2 SureColor T3000 x 3 SureColor T52. from the control panel and examine it to determine whether any nozzles are clogged or deflected Then you can run a cleaning cycle if necessary 1 2 Make sure the paper source and media type settings are correct for the type of paper loaded Confirm that the printer is ready to print then press the AA button the control panel The Maintenance menu will be displayed Confirm that Nozzle Check is highlighted and press the OK button A confirmation message will be displayed Press OK to print a nozzle check pattern Examine the printed pattern e If the pattern looks good as shown below the print head is clean Ifany dots or segments are missing or deflected as shown below follow the instructions on the control panel to run a cleaning cycle Then print another nozzle check pattern to make sure the nozzles are clean 20 Aligning the Print Head Aligning the Print Head Follow the steps below to align the print head using the printer s control panel Make sure the paper source and media type settings are correct for the type of paper loaded 1 Confirm that the printer is ready to print Press 4 gt on the control panel to highlight settings and press OK The Maintenance menu will be displayed 2 Press W to select Head Alignment then press OK 3 Press W to select Auto Bi D then press OK 4 Press OK again to begin the head alignment The printer will automatically align the head as it print
3. 000 x 4 SureColor T7000 xs x4 1 Attach the two basket holders as shown one on each side of the stand Use four bolts to fasten the holders in place Attaching the Paper Basket 7 2 Attach the stack guides to the bottom of the printer Make sure each guide snaps securly into place 2 SureColor T3000 x 3 SureColor T5000 x 4 SureColor T7000 3 Insert a plastic connector into one end of the square pole os oy 4 Slide the pole through the holes in the stack guides and attach the other plastic connector to the end of the pole Then fasten the plastic connectors in place on each side of the stand as shown 8 Attaching the Paper Basket 5 Attach the shorter arm to the inside of the basket holder on the left side of the printer Use two nuts to hold the arm in place 7 Insert the longer arm into the rounded pole as shown Attaching the Paper Basket 9 8 Slide the pole through the basket cloth until it comes out the other end The small hole in the cloth will be on the right side as shown below 9 Flip up the basket holder on the right side of the printer 10 Insert the end of the rounded pole into the arm on the left side of the printer Then flip down the basket holder on the right side of the printer and insert the right side basket arm as shown 10 Attaching the Paper Basket 11 Use two nuts and two bolts to fasten the arm in place 12 On the back side of the pr
4. EPSON EXCEED YOUR VISION 9 9 JOJODaINS uosd4 Setup Guide Epson T Series Control Panel Power button and light Pause cancel button Maintenance button Load remove paper button Media feed button cut button Menu button LCD display Back button Help button Contents Unpacking and Assembling the Printer scsi stiles coh anagem 2 3 Mounting the Printer on the Stand 5 Attichine th Papen Basket a a a 6 Connecting the Power Gord 11 Installing a E EE REER T 12 Beading Paper beac than cost const atts E 13 Performing a Test Print 19 Alining the Print Head 20 Tostalling 20 Connecting to Your Sys tenn ar I 20 Upd ting Your Printer Firmware aR Eaa a aroi aai Oraa aaaea aRt 21 Checking the Current Firmware Version 21 U
5. he ink cartridges in the printer Hold each cartridge with the arrow pointing toward the printer then insert it into its slot until it clicks into place Make sure you insert each cartridge all the way into the correct slot Cyan Yellow Magenta MK MB Matte Black PK BK Photo Black Loading Roll Paper 13 4 Close the ink cover and wait for the ink to charge The ink charging process takes about 22 minutes Caution Do not turn off the printer or open the ink cover when it is charging or you may waste ink When the ink charging is completed press 0 45 and Load paper will be displayed on the control panel Do not perform operations other than those specified on the screen Loading Roll Paper Before you start you may want to close the paper basket This will make it easier to access the top of the printer during the paper loading process 14 Loading Roll Paper 1 Open the roll paper cover 2 Raise the roll lock lever Loading Roll Paper 15 4 If necessary adjust the roll media adapters to fit the core size of the roll paper 2 inch core 3 inch core 8 8 5 6 Push the adapters into the paper core at both ends of the roll Press the adapters in until they are fully inserted into the roll 7 Push down the tension lever on both adapters to secure them 16 Loading Roll Pape
6. inter pull the paper basket up so that the stack guides fit into the slots as shown Then hook the loops around the pins on the back of the stack guides to hold the basket in place 2 SureColor T3000 3 SureColor T5000 x 4 SureColor T7000 13 Hook the loops on the sides of the basket to the pins on the back of the stand legs to secure the basket to the printer Connecting the Power Cord 11 14 On the front side of the printer slide the basket s fabric all the way to the ends of the rounded pole as shown Connecting the Power Cord 1 Unlock the casters Then move the printer to the place of use The casters are meant for moving the printer for only a short distance Lock the casters after moving 2 Connect the power cord to the AC inlet on the side of the printer 3 Plug the power cord into a properly grounded electrical outlet 12 Installing Ink Cartridges Installing Ink Cartridges Use the ink cartridges that came with your printer for initial ink charging During the initial installation process it is normal for most of the ink in each cartridge to be used 1 Turn on the power and configure the initial settings such as the language and date Then follow the instructions on the control panel to install the ink cartridges 2 Unpack the ink cartridges and shake each 30 times about 10 seconds PF Note Do not touch the IC chip on the cartridge 3 Install t
7. pd ting th Firmware 21 2 Unpacking and Assembling the Printer Unpacking and Assembling the Printer Note Unless otherwise indicated the illustrations in this manual show the SureColor T7000 but the instructions apply to all three models Before beginning assembly make sure you have sufficient space to set up and use the printer The following illustration shows the minimum space required for using the printer 5 9 in 150 mm 0 4 in 10 mm 23 6 in 600 mm 5 9 in 150 mm When choosing a place for the printer leave adequate room for easy access and ventilation Avoid locations subject to direct sunlight excessive heat humidity or dust Be sure the printer is placed on a flat stable location that can support the following weight for each printer e SureColor T3000 112 lb 51 kg e SureColor T5000 165 lb 75 kg e SureColor T7000 180 lb 82 kg WARNING Two people are required to unpack and install the SureColor T3000 printer four people are recommended to unpack and install the SureColor T5000 or SureColor T7000 printer You need an even larger floor space to assemble the printer and stand so be sure to prepare a large clear area before unpacking them Also make sure you save the box and packaging in case you need to ship the printer later Assembling the Stand 3 The following items are included with your printer Hex wrench Ink
8. r 8 Slide the roll paper all the way to the right until it lines up with the adapter guides 9 Press the 0 9 button on the control panel Confirm that Roll Paper is highlighted in the display then press the OK button 10 Insert the end of the roll paper into the paper slot and pull it through Make sure the paper is free of slack and that the end is not folded Loading Roll Paper 17 11 Pull the paper straight through until the leading edge reaches the front of the printer 12 Lower the roll lock lever 13 Following the instructions on the control panel press the OK button The paper will be fed into the printer 18 Loading Roll Paper 14 Close the roll paper cover 15 Check the message on the control panel e If the paper type was automatically detected the printer will display Ready on the LCD screen The printer is ready to print e If the paper type was not detected the printer will display the Paper Type and Roll Paper Remaining settings for the paper currently selected Follow the instructions on the control panel to change or confirm the current settings Press OK when finished 16 Before printing open the paper basket if necessary Note See the User s Guide for information on loading cut sheets and poster board Performing a Test Print 19 Performing a Test Print You can print a nozzle check
9. s the head alignment pattern When alignment is complete the Maintenance menu will be displayed Note See the User s Guide for instructions on performing a manual head alignment Installing Software Insert the software CD that came with your printer into your computer and follow the on screen instructions Connecting to Your System You can use USB and or Ethernet network connections For USB connection make sure your system has the appropriate port and that you have a standard shielded cable 10 feet 3 m long or less Note Do not connect the printer until a software installation screen prompts you to do so Updating Your Printer Firmware 21 To connect to a network hub or directly to your computer s network interface you need a standard RJ 45 CAT 6 network cable 1 Plug the interface cable into the appropriate port on the printer 2 Plug the other end of the cable into the appropriate port your computer network switch or hub Updating Your Printer Firmware To keep your printer features and functionality up to date you should check for a new version of firmware on the Epson support site and update your printer if necessary Checking the Current Firmware Version 1 Press the gt button twice to highlight settings 2 Press the Menu button 3 Press the button until Printer Status is highlighted then press 4 Press OK again Note the firmware ver
10. sion displayed When finished press the II button Updating the Firmware Before updating your printer s firmware make sure your printer is turned on and connected to your computer or network 1 Click the EPSON LFP Remote Panel 2 icon on your desktop You see the EPSON LFP Remote Panel 2 Make sure your printer is selected from the drop down menu 2 Click the Firmware Updater button You see the Firmware Updater window 22 Updating the Firmware Click Acquire Latest Information to automatically download the latest firmware version for your printer from the internet If there is a firmware update the message Found the latest firmware information Do you want to download the firmware file appears Click Yes to download the file Note If the Acquire Latest Information button fails to download the latest firmware you can also find it by visiting Epson s support site epson com support US or epson ca support Canada You will need download the latest version and upload it by clicking Browse and locating the file then continue from step 5 When the message File download complete appears click OK The file you just downloaded should automatically be selected and appear in the File Name window Click Update and follow the on screen instructions If the firmware version of the file is newer than what is currently installed click Update to start the firmware updating process Caution Don t turn off the printer
11. while the firmware is updating When the update is complete close the Firmware Updater window and EPSON LFP Remote Panel 2 window 3 ENERGY STAR EPSON and SureColor are registered trademarks and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation General Notice Other product names used herein are for identification purposes only and may be trademarks of their respective owners Epson disclaims any and all rights in those marks This information is subject to change without notice 2012 Epson America Inc 10 12 CPD 38235
Download Pdf Manuals
Related Search