Epson PowerLite 8000NL Parts User Manual
Contents
1. Be sure to remove the front lens cap before turning on the power or it may melt from the heat 3 Mounting the front case 1 Set the front case into position and tighten the two screws This completes installation e Turn on the power and verify that the projector operates nor mally 4 Rear projection wide angle lens specifications 4 1 Lens specifications 1 Focal length 27mm 2 f number 2 3 3 Projection size 60 to 100 inches 4 Mass 1600 g 4 2 Appearance with rear projector wide lens mounted About 455mm User s Manual for ELPLS01 Standard Lens e This standard lens is designed for use only with EPSON multimedia pro jectors e Please read this manual completely before use to assure maximum per formance e Note that illustrations may differ slightly from your actual product e Specifications are subject to change without notice Safety Precautions To assure that this product is used safely and to help prevent dam age or injury the following symbols are used in the manual Please read this manual thoroughly before use to ensure safety and opti mum performance Z Warning Ignoring this warning or implementing the content in correctly could result in injury or even death Important information such as additional explanations key points to remember and things to avoid doing 1 Before mounting the standard lens 1 1 Safety precautions Z Warning Be sure to screw the L2. adapter ring down completely Unless they are securely screwed on they could fall off and cause damage or injury especially when the projector is ceiling mounted 1 2 Check product contents e Make sure that you have all the parts as shown below before starting Rear lens cap Zoom lens Used to tighter remove mounting screws Hex wrench User s manual this document Used to loosen and tighten the ring mounting screws e In addition to the included screwdriver you will also need a Phillips screwdriver and various other common tools Be sure to use a Phillips screwdriver that fits the screws properly 2 Mounting the rear projection wide angle lens Warning Be sure to disconnect the power cable before installa tion because there is danger of electrical shock Always mount and dismount the lens in a clean room to minimize the amount of dust Excessive dust inside the lens could cause damage e Note that the illustrations below may not match your particu lar projector model 2 1 Removing the current lens 1 Remove the front case 1 Remove the two mounting screws and pull off the front case Front case Screws two 2 Remove the current lens 1 Use the enclosed screwdriver to remove the four mounting screws and dismount the current lens Current lens Sa 2 2 Mounting the rear projection wide angle lens 1 Mounting the rear projection wide angle l
3. specifications 1 Focal length 68 3 to 116 2 mm 2 Zoom ratio 1 7 x 3 f number 2 14 to 2 98 4 Projection size 60 to 300 inches 5 Mass 2100 g 4 2 Appearance with zoom lens mounted About 505mm User s Manual for Long Throw Zoom Lens ELPLL03 e This long throw zoom lens is designed for use only with EPSON multi media projectors e It makes it possible to increase the distance between the projector and the screen e Please read this manual completely before use to assure maximum per formance e Note that illustrations may differ slightly from your actual product e Specifications are subject to change without notice Safety Precautions To assure that this product is used safely and to help prevent dam age or injury the following symbols are used in the manual Please read this manual thoroughly before use to ensure safety and opti mum performance A Warning Ignoring this warning or implementing the content in correctly could result in injury or even death Important information such as additional explanations key points to remember and things to avoid doing 1 Before mounting the zoom lens 1 1 Safety precautions A Warning Be sure to screw the Long throw zoom lens and adapter ring down completely Unless they are securely screwed on they could fall off and cause damage or injury es pecially when the projector is ceiling mounted 1 2 Check product contents e Make sure t
4. Screws three 2 Remove the current lens 1 Use the enclosed screwdriver to remove the four mounting screws and dismount the current lens Current lens Q VG 2 2 Mounting the zoom lens 1 Mounting the zoom lens 1 Remove the rear lens cap 2 Use the enclosed screwdriver to mount the zoom lens with the four mounting screws Be sure that the seal reading UPPER is on top o Rear lens cap 2 Mounting the front case 1 Set the front case into position and tighten the three screws This completes installation e Turn on the power and verify that the projector operates nor mally e Be sure to remove the front lens cap be fore turning on the power or it may melt from the heat e When handling the zoom lens take care not to catch your finger between the lens and the tabletop 4 Zoom lens specifications 4 1 Lens specifications 1 Focal length 37 9 to 45 5 mm 2 Zoom ratio 1 4 3 f number 2 34 to 2 65 4 Projection size 60 to 200 inches 5 Mass 2600 g 4 2 Appearance with zoom lens mounted About 480mm
5. User s Manual for ELPLLO2 Long Focal Length Zoom Lens e This long focal length zoom lens is designed for use only with EPSON multimedia projectors e It makes it possible to increase the distance between the projector and the screen e Please read this manual completely before use to assure maximum per formance e Note that illustrations may differ slightly from your actual product e Specifications are subject to change without notice Safety Precautions To assure that this product is used safely and to help prevent dam age or injury the following symbols are used in the manual Please read this manual thoroughly before use to ensure safety and opti mum performance Wartning Ignoring this warning or implementing the content in correctly could result in injury or even death Important information such as additional explanations key points to remember and things to avoid doing 1 Before mounting the zoom lens 1 1 Safety precautions Z Warning Be sure to screw the Long Focal Length lens and adapter ring down completely Unless they are securely screwed on they could fall off and cause damage or injury especially when the projector is ceiling mounted 1 2 Check product contents e Make sure that you have all the parts as shown below before starting Rear lens cap Zoom lens Front lens cap User s manual this document Used to tighter remove mounting screws e In additio
6. e content in correctly could result in injury or even death Important information such as additional explanations key points to remember and things to avoid doing 1 Before mounting the zoom lens 1 1 Safety precautions A Warning Be sure to screw the Long Focal Length lens and adapter ring down completely Unless they are securely screwed on they could fall off and cause damage or injury especially when the projector is ceiling mounted 1 2 Check product contents e Make sure that you have all the parts as shown below before starting Rear lens cap Zoom lens User s manual this document Used to tighter remove mounting screws e In addition to the included screwdriver you will also need a Phillips screwdriver and various other common tools Be sure to use a Phillips screwdriver that fits the screws properly 2 Mounting the zoom lens A Warning Be sure to disconnect the power cable before installa tion because there is danger of electrical shock Always mount and dismount the lens in a clean room to minimize the amount of dust Excessive dust inside the lens could cause damage e Note that the illustrations below may not match your par ticular projector model 2 1 Removing the current lens 1 Remove the front case 1 Remove the three mounting screws and pull off the front case The two components will separate from each other Front case
7. ens 1 Remove the rear lens cap 2 Use the enclosed screwdriver to mount the rear projector wide lens with the four mounting screws Be sure that the seal read ing UPPER is on top Seal O used OT pp tt SS KO Rear lens cap KO 2 Adjusting the wide lens for a rear projector e This lens must be adjusted to match the screen size Adjust the lens as follows before installing the front case 1 Turn the lens shift button to move the lens all the way down 2 Loosen the 2 focus ring mounting screws by using the hex wrench that came in the same package 3 Loosen the 2 resolving plane correction ring mounting screws with the hex wrench 4 Turn on the projector power 5 Rotate the two rings to adjust the image to the optimum appear ance The resolving plane correction ring should provide a sharp image across the entire screen area 6 Use the hex wrench to retighten the four ring mounting screws 7 Turn off the power and disconnect the power cable Z WARNING DO NOT TOUCH Lens shift button Resolving plane correction ring Focus ring Focus ring mounting screws Resolving plane correction ring mounting screws Z Warning Turn the power only when adjusting the lens Always disconnect the power cable at other times When adjusting the lens take care not to touch any other parts of the projector or lens as there is a danger of electric shock with the front case open
8. hat you have all the parts as shown below before starting Rear lens cap Zoom lens Front lens cap User s manual this document Used to tighter remove mounting screws e In addition to the included screwdriver you will also need a Phillips screwdriver and various other common tools Be sure to use a Phillips screwdriver that fits the screws properly 2 Mounting the zoom lens A Warning Be sure to disconnect the power cable before installa tion because there is danger of electrical shock Always mount and dismount the lens in a clean room to minimize the amount of dust Excessive dust inside the lens could cause damage e Note that the illustrations below may not match your par ticular projector model 2 1 Remove the current lens 1 Remove the front case 1 Remove the two mounting screws and pull off the front case Front case Screws two 2 Remove the current lens 1 Use the enclosed screwdriver to remove the four mounting screws and dismount the current lens Current lens 2 2 Mounting the zoom lens 1 Mounting the zoom lens 1 Remove the rear lens cap 2 Use the enclosed screwdriver to mount the zoom lens with the four mounting screws Be sure that the seal reading UPPER is on top D KO KO Rear lens cap 2 Mounting the front case 1 Set the front case into position and tighten the two screws This completes installation e Tu
9. n to the included screwdriver you will also need a Phillips screwdriver and various other common tools Be sure to use a Phillips screwdriver that fits the screws properly 2 Mounting the zoom lens Wartning Be sure to disconnect the power cable before installa tion because there is danger of electrical shock Always mount and dismount the lens ina clean room to minimize the amount of dust Excessive dust inside the lens could cause damage e Note that the illustrations below may not match your par ticular projector model 2 1 Removing the current lens 1 Remove the front case 1 Remove the two mounting screws and pull off the front case Front case Screws two 2 Remove the current lens 1 Use the enclosed screwdriver to remove the four mounting screws and dismount the current lens Current lens KO 2 2 Mounting the zoom lens 1 Mounting the zoom lens 1 Remove the rear lens cap 2 Use the enclosed screwdriver to mount the zoom lens with the four mounting screws Be sure that the seal reading UPPER is on top Rear lens cap 2 Mounting the front case 1 Set the front case into position and tighten the two screws This completes installation e Turn on the power and verify that the projector operates nor mally Be sure to remove the front lens cap before turning on the power or it may melt from the heat 4 Zoom lens specifications 4 1 Lens
10. ong Focal Length lens and adapter ring down completely Unless they are securely screwed on they could fall off and cause damage or injury especially when the projector is ceiling mounted 1 2 Check product contents e Make sure that you have all the parts as shown below before starting Rear lens cap Standard lens Front lens cap ke hy Bey 2 Screwdriver Za User s manual this document Used to tighter remove mounting screws e In addition to the included screwdriver you will also need a Phillips screwdriver and various other common tools Be sure to use a Phillips screwdriver that fits the screws properly 2 Mounting the standard lens A Warning Be sure to disconnect the power cable before installa tion because there is danger of electrical shock Always mount and dismount the lens in a clean room to minimize the amount of dust Excessive dust inside the lens could cause damage e Note that the illustrations below may not match your par ticular projector model 2 1 Removing the current lens 1 Remove the front case 1 Remove the two mounting screws and pull off the front case Front case Screws two 2 Remove the current lens 1 Use the enclosed screwdriver to remove the four mounting screws and dismount the current lens Current lens 2 2 Mounting the standard lens 1 Mounting the standard lens 1 Remove the rear lens cap 2 Use the enclosed scre
11. rn on the power and verify that the projector operates nor mally Be sure to remove the front lens cap before turning on the power or it may melt from the heat 4 Zoom lens specifications 4 1 Lens specifications 1 Focal length 144 1 to 194 5mm 2 Zoom ratio 1 35 x 3 f number 2 60 to 3 27 4 Projection size 80 to 300 inches 5 Mass 2100 g 4 2 Appearance with zoom lens mounted About 505mm User s Manual for ELPLR01 Rear Projector wide Lens e This wide angle lens is designed for use only on EPSON multimedia projectors e This lens is designed for use only on rear projection and rear projection box systems e Please read this manual completely before use to assure maximum per formance e Note that illustrations may differ slightly from your actual product e Specifications are subject to change without notice Safety Precautions To assure that this product is used safely and to help prevent dam age or injury the following symbols are used in the manual Please read this manual thoroughly before use to ensure safety and opti mum performance Warning Ignoring this warning or implementing the content in correctly could result in injury or even death Important information such as additional explanations key points to remember and things to avoid doing 1 Before mounting the wide angle lens 1 1 Safety precautions Z Warning Be sure to screw the Rear Projector wide lens and
12. wdriver to mount the standard lens with the four mounting screws Be sure that the seal reading UP PER is on top N x gt Q ra 7 SASS Set Rear lens cap 2 Mounting the front case 1 Set the front case into position and tighten the two screws This completes installation e Turn on the power and verify that the projector operates nor mally Be sure to remove the front lens cap before turning on the power or it may melt from the heat 4 Standard lens specifications 4 1 Lens specifications 1 Focal length 49 2 to 68 9 mm 2 Zoom ratio 14x 3 f number 1 84 to 2 36 4 Projection size 30 to 300 inches 5 Mass 1300 g 4 2 Appearance with standard lens mounted About 475mm User s Manual for the ELPLW01 Wide Zoom Lens e This wide zoom lens is designed for use only with EPSON multimedia projectors e It makes it possible to decrease the distance between the projector and the screen e Please read this manual completely before use to assure maximum per formance e Note that illustrations may differ slightly from your actual product e Specifications are subject to change without notice Safety Precautions To assure that this product is used safely and to help prevent dam age or injury the following symbols are used in the manual Please read this manual thoroughly before use to ensure safety and opti mum performance Z Warning Ignoring this warning or implementing th
Download Pdf Manuals
Related Search