Enterasys Networks BL-6000ENT User's Manual
Contents
1. Verify that there are no loose parts inside the Mid Span Power Hub If needed check and replace fuse at the inlet plug 10 A rated fuse The Mid Span Power Hub operates but one of the powered devices does not work Verify that you are using a standard UTP Cat 5 5e or 6 cable including all eight wires four pairs Try to move the same load into a different port on the same hub If it works there is probably a faulty port or bad RJ45 port connection If possible try to connect the load device into a different hub Try using a different Ethernet cable if it works there is probably a faulty connection over the long cable or a bad RJ45 connection Mid Span Power Hub User s Guide 3 1 Table 3 1 Troubleshooting Checklist continued Problem Recommended Action The Mid Span Power Hub operates and the load device works but there is no data link Verify that the Detect Power Forwarding blue LED for the port is on Verify that the Mid Span Power Hub is connected to the Ethernet network with a good connection Verify that the Ethernet cable is Category 5 5e or 6 and is less than 100 meters in length from the Ethernet source to the load Try to connect a different device over the same port If it works and a link is established there is probably a faulty data link in the load Try to reconnect the load into a different output port remember to move the input port accordingly If it works th2. Installationen oder Servicearbeiten sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden Verifying the Kit Unpack the unit and verify that you have all of the following items see Figure 2 2 e Enterasys Networks 8 port or 24 port Mid Span Power Hub e Power Cord e User s Guide Mid Span Power Hub User s Guide 2 1 Kit Contents Kit Contents Figure 2 1 Contents of the BL 69108ENT Kit BL 69108ENT 8 Port Mid Span Power Hub COLLEEN Power Cord Figure 2 2 Contents of the BL 69524ENT Kit BL 69524ENT 24 Port Mid Span Power Hub TRI if Power Cord n 2 2 Installation and Connection Technical Considerations Technical Considerations An Enterasys Networks Mid Span Power Hub may be placed on a shelf or mounted in a standard 48 26 centimeter 19 inch rack Before you mount the unit to a fixed location consider the following e Determine optimal placement e Collect and document network information as required e Ensure that the length of cable from the Ethernet network source to the powered device does not exceed 100 meters Note The units are not repeaters and do not amplify the Ethernet data signal Caution Observe the following requirements when mounting the Enterasys Networks Mid Span Power Hubs e The unit is intended for installation in a wiring closet e Connect the unit to a grounding type AC outlet 100 240 VAC using the standard power cord s
3. A PARTICULAR PURPOSE TITLE AND NON INFRINGEMENT WITH RESPECT TO THE PROGRAM IF IMPLIED WARRANTIES MAY NOT BE DISCLAIMED BY APPLICABLE LAW THEN ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THIRTY 30 DAYS AFTER DELIVERY OF THE PROGRAM TO YOU 7 LIMITATION OF LIABILITY IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF BUSINESS PROFITS BUSINESS INTERRUPTION LOSS OF BUSINESS INFORMATION SPECIAL INCIDENTAL CONSEQUENTIAL OR RELIANCE DAMAGES OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES THIS FOREGOING LIMITATION SHALL APPLY REGARDLESS OF THE CAUSE OF ACTION UNDER WHICH DAMAGES ARE SOUGHT THE CUMULATIVE LIABILITY OF ENTERASYS TO YOU FOR ALL CLAIMS RELATING TO THE PROGRAM IN CONTRACT TORT OR OTHERWISE SHALL NOT EXCEED THE TOTAL AMOUNT OF FEES PAID TO ENTERASYS BY YOU FOR THE RIGHTS GRANTED HEREIN vii 8 AUDIT RIGHTS You hereby acknowledge that the intellectual property rights associated with the Program are of critical value to Enterasys and accordingly You hereby agree to maintain complete books records and accounts showing i license fees due and paid and ii the use copying and deployment of the Program You also grant to Enterasys and its authorized representatives upon reasonable notice the right to audit and examine during Your normal bu
4. by applicable law and to the extent the parties shall not be permitted by that applicable law such rights are expressly excluded Information necessary to achieve interoperability or correct errors is available from Enterasys upon request and upon payment of Enterasys applicable fee ii Incorporate the Program in whole or in part in any other product or create derivative works based on the Program in whole or in part iii Publish disclose copy reproduce or transmit the Program in whole or in part iv Assign sell license sublicense rent lease encumber by way of security interest pledge or otherwise transfer the Program in whole or in part v Remove any copyright trademark proprietary rights disclaimer or warning notice included on or embedded in any part of the Program vi 3 APPLICABLE LAW This Agreement shall be interpreted and governed under the laws and in the state and federal courts of the Commonwealth of Massachusetts without regard to its conflicts of laws provisions You accept the personal jurisdiction and venue of the Commonwealth of Massachusetts courts None of the 1980 United Nations Convention on Contracts for the International Sale of Goods the United Nations Convention on the Limitation Period in the International Sale of Goods and the Uniform Computer Information Transactions Act shall apply to this Agreement 4 EXPORT RESTRICTIONS You understand that Enterasys and its Affiliates are subject to r
5. out of the product being used in a negligent fashion or manner NOTE Enterasys Networks reserves the right to change specifications without notice Please contact your representative to confirm current specifications Enterasys Networks Inc Firmware License Agreement BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT CAREFULLY READ THIS LICENSE AGREEMENT This document is an agreement Agreement between the end user You and Enterasys Networks Inc on behalf of itself and its Affiliates as hereinafter defined Enterasys that sets forth Your rights and obligations with respect to the Enterasys software program firmware installed on the Enterasys product including any accompanying documentation hardware or media Program in the package and prevails over any additional conflicting or inconsistent terms and conditions appearing on any purchase order or other document submitted by You Affiliate means any person partnership corporation limited liability company or other form of enterprise that directly or indirectly through one or more intermediaries controls or is controlled by or is under common control with the party specified This Agreement constitutes the entire understanding between the parties and supersedes all prior discussions representations understandings or agreements whether oral or in writing between the parties with respect to the subject matter of this Agreement The Progra
6. www enterasys com services support Phone 1 800 872 8440 toll free in U S and Canada or 1 978 684 1000 For the Enterasys Networks Support toll free number in your country www enterasys com services support contact Internet mail support enterasys com To expedite your message type other in the subject line To send comments concerning this document to the Technical Publications Department techpubs enterasys com Please include the document Part Number in your email message Before contacting Enterasys Networks for technical support have the following information ready e Your Enterasys Networks service contract number e A description of the failure xii About This Guide Getting Help A description of any action s already taken to resolve the problem for example changing mode switches or rebooting the unit The serial and revision numbers of all involved Enterasys Networks products in the network A description of your network environment for example layout or cable type Network load and frame size at the time of trouble if known The device history for example have you returned the device before or is this a recurring problem Any previous Return Material Authorization RMA numbers Mid Span Power Hub User s Guide xiii Getting Help xiv About This Guide Introduction Functions and Features The BL 69108ENT and BL 69524ENT Enterasys Networks 8 port and 24 port Mid Sp
7. 0950 73 23 EEC EN 60950 Produktsicherheit Dieses Produkt entspricht den folgenden Richtlinien UL 60950 CSA C22 2 No 60950 73 23 EEC EN 60950 Electromagnetic Compatibility EMC This product complies with the following 47 CFR Parts 2 and 15 CSA C108 8 89 336 EEC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 AS NZS CISPR 22 VCCI V 3 Compatibilidad Electromagnetica EMC Este producto de Enterasys cumple con lo siguiente 47 CFR Partes 2 y 15 CSA C108 8 89 336 EEC EN 55022 EN 55024 EN 61000 3 2 EN 61000 3 3 AS NZS CISPR 22 VCCI V 3 Elektro magnetische Kompatibilitat EMC Dieses Produkt entspricht den folgenden Richtlinien 47 CFR Parts 2 and 15 CSA C108 8 89 336 EEC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 AS NZS CISPR 22 VCCI V 3 TOV Rheinland Product Safety Hazardous Substances This product complies with the requirements of European Directive 2002 95 EC Restriction of Hazardous Substances RoHS in Electrical and Electronic Equipment European Waste Electrical and Electronic Equipment WEEE Notice In accordance with Directive 2002 96 EC of the European Parliament on waste electrical and electronic equipment WEEE 1 The symbol above indicates that separate collection of electrical and electronic equipment is required and that this product was placed on the European market after August 13 2005 the date of enforcement for Directive 2002 96 EC 2 When this product has reached the e
8. 7 5x9 inch cover with bleed on 4 sides Mid Span Power Hub 8 Port and 24 Port User s Guide enterasys P N 9033926 02 Networks that Know Electrical Hazard Only qualified personnel should perform installation procedures A Riesgo Electrico Solamente personal calificado debe realizar procedimientos de instalacion Elektrischer Gefahrenhinweis Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden Notice Enterasys Networks reserves the right to make changes in specifications and other information contained in this document and its web site without prior notice The reader should in all cases consult Enterasys Networks to determine whether any such changes have been made The hardware firmware or software described in this document is subject to change without notice IN NO EVENT SHALL ENTERASYS NETWORKS BE LIABLE FOR ANY INCIDENTAL INDIRECT SPECIAL OR CONSEQUENTIAL DAMAGES WHATSOEVER INCLUDING BUT NOT LIMITED TO LOST PROFITS ARISING OUT OF OR RELATED TO THIS DOCUMENT WEB SITE OR THE INFORMATION CONTAINED IN THEM EVEN IF ENTERASYS NETWORKS HAS BEEN ADVISED OF KNEW OF OR SHOULD HAVE KNOWN OF THE POSSIBILITY OF SUCH DAMAGES Enterasys Networks Inc 50 Minuteman Road Andover MA 01810 2006 Enterasys Networks Inc All rights reserved Part Number 9033926 02 June 2006 ENTERASYS ENTERASYS NETWORKS LANVIEW NETSIGHT WEBVIEW and any logos associated therewith are
9. CEMENT You acknowledge and agree that any breach of Sections 2 4 or 9 of this Agreement by You may cause Enterasys irreparable damage for which recovery of money damages would be inadequate and that Enterasys may be entitled to seek timely injunctive relief to protect Enterasys rights under this Agreement in addition to any and all remedies available at law 11 ASSIGNMENT You may not assign transfer or sublicense this Agreement or any of Your rights or obligations under this Agreement except that You may assign this Agreement to any person or entity which acquires substantially all of Your stock or assets Enterasys may assign this Agreement in its sole discretion This Agreement shall be binding upon and inure to the benefit of the parties their legal representatives permitted transferees successors and assigns as permitted by this Agreement Any attempted assignment transfer or sublicense in violation of the terms of this Agreement shall be void and a breach of this Agreement 12 WAIVER A waiver by Enterasys of a breach of any of the terms and conditions of this Agreement must be in writing and will not be construed as a waiver of any subsequent breach of such term or condition Enterasys failure to enforce a term upon Your breach of such term shall not be construed as a waiver of Your breach or prevent enforcement on any other occasion 13 SEVERABILITY In the event any provision of this Agreement is found to be invalid illegal or
10. an Power Hubs support applications in which AC power is difficult to access such as VoIP phones wireless LAN access points or IP network cameras The Enterasys Mid Span Power Hubs act as patch panels and add 48 VDC to unused non data wires in standard Category 5 5e or 6 Ethernet cable The power unit delivers both data and power over a single standard Ethernet cable Main features of the Mid Span Power Hubs e Fully hot swappable module banks e Remote power feeding powered devices receive power over the Ethernet cable e Centralized power distribution one powered device can be connected to a single in line unit e IEEE 802 3af standard powering scheme e Actas normal patch panels and place 48 VDC on unused Ethernet pins e Total power available 15 6 W per port per IEEE specification e Automatic power control circuitry to detect a powered device before providing power e Fused power surge protection Port Indicators Each port has its own LEDs which display the following e Detect Power Forwarding blue e Power from Chassis green For information on Troubleshooting refer to Table 3 1 on page 3 1 Mid Span Power Hub User s Guide 1 1 Port Indicators 1 2 Introduction Installation and Connection Electrical Hazard Only qualified personnel should install or service this unit Riesgo El ctrico Solamente personal capacitado debe de instalar o darle servicio a esta unida Elektrischer Gefahrenhinweis
11. egulation by agencies of the U S Government including the U S Department of Commerce which prohibit export or diversion of certain technical products to certain countries unless a license to export the Program is obtained from the U S Government or an exception from obtaining such license may be relied upon by the exporting party If the Program is exported from the United States pursuant to the License Exception CIV under the U S Export Administration Regulations You agree that You are a civil end user of the Program and agree that You will use the Program for civil end uses only and not for military purposes If the Program is exported from the United States pursuant to the License Exception TSR under the U S Export Administration Regulations in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement You agree not to i reexport or release the Program the source code for the Program or technology to a national of a country in Country Groups D 1 or E 2 Albania Armenia Azerbaijan Belarus Bulgaria Cambodia Cuba Estonia Georgia Iraq Kazakhstan Kyrgyzstan Laos Latvia Libya Lithuania Moldova North Korea the People s Republic of China Romania Russia Rwanda Tajikistan Turkmenistan Ukraine Uzbekistan Vietnam or such other countries as may be designated by the United States Government ii export to Country Groups D 1 or E 2 as defined herein the direct product of the Program or the techno
12. ere is probably a faulty output or input port in the Mid Span Power Hub or a bad RJ45 connection The Mid Span Power Hub operates but one of the ports is powering a load without turning the Power LED on Move the load into a different output port If the LED turns on there is a fault in the previous output port 3 2 Troubleshooting Hardware Specifications Regulatory Compliance Standards This equipment meets the following safety and electromagnetic compatibility EMC requirements Safety UL 60950 CSA C22 2 No 60950 73 23 EEC EN 60950 IEC 60950 Electromagnetic Compatibility 47 CFR Parts 2 and 15 CSA C 108 8 89 336 EEC EN 55022 EMC EN 61000 3 2 EN 61000 3 3 EN 55024 AS NZS CISPR 22 VCCI V 3 Product Standards This equipment meets the following product standards Standards IEEE 802 3af Specifications Model BL 69108ENT e 8 female RJ45 data input ports e Shielded jacks for Category 5 or greater UTP two pair wire or 100 ohm STP two pair wire e Distance Up to 100 meters standard Ethernet distance e 8 female RJ45 Data Power on Ethernet Power over Ethernet output ports Mid Span Power Hub User s Guide A 1 Specifications Model BL 69524ENT e 24 female RJ45 data input ports e Shielded jacks for Category 5 or greater UTP two pair wire or 100 ohm STP two pair wire e Distance Up to 100 meters standard Ethernet distance e 24 female RJ45 Data Power on Et
13. hernet Power over Ethernet output ports Physical Mechanical Specifications Table A 1 provides physical and mechanical specifications for the 8 port and 24 port Mid Span Power Hubs Table A 1 Physical and Mechanical Specifications Item Specification BL 69108ENT Chassis Type Shelf mount with rubber feet Chassis Size 30 48 cm W x 26 67 cm D x 5 08 cm H 12in W x 10 5 in D x 2 0 in H Module Type Removable hot swappable Weight 1 0 kg 2 0 Ib BL 69524ENT Chassis Type 48 26 cm 19 0 in rackmount with 3 modules Chassis Size 44 45 cm W x 41 28 cm D x 4 45 cm H 17 5 in W x 16 25 in D x 1 75 in H Module Type Removable hot swappable Weight 9 0 kg 20 Ib LED Indicators Module Table A 2 provides module LED states and their definitions Table A 2 LED States and Their Definitions LED Color Status Blue Detect Power Forwarding Green Power from Chassis A 2 Specifications Physical Environmental Specifications Table A 2 provides physical and environmental specifications for the 8 Port BL 69108ENT and 24 Port BL 69524ENT Mid Span Power Hubs Table A 3 Physical and Environmental Specifications Item Specification Operating Temperature 0 C to 40 C 32 to 105 F Storage Temperature 10 C to 60 C 14 F to 140 F Relative Humidity 10 to 90 non condensing Operating Altitude Electrical Specifications AC P
14. hipped with the unit or a user supplied UPS uniterruptible power supply e Allow for easy access to disconnect the unit from the AC outlet if necessary e Do not cover the unit or block the airflow with any other objects Keep the unit away from excessive heat humidity vibration and dust e Ensure that installation conforms to local regulations Configuration for a Mid Span Power Hub Figure 2 3 shows a typical configuration for an Enterasys Networks Mid Span Power Hub BL 69524ENT shown operating with 802 3af appliances To ensure EMC compliance and compliance with Class A requirements use Category 5 5e or 6 shielded twisted pair straight through cables Mid Span Power Hub User s Guide 2 3 Powering Up Figure 2 3 Typical Configuration for a Mid Span Power Hub Layer 3 Switch Enterasys BL 69108ENT S or BL 69524ENT shown i _ Mid Span Power Hub Z SS S Powered Devices e IEEE802 3af Compatible C Sa Data amp Power Out Data In Q Powering Up Simply plug one end of the power cord into the unit and the other end into a grounded AC power source Units are typically connected to a power strip or other power outlet that may be cycled on and off An uninterruptible power supply may also be used Check to make sure each module installed displays a green Power LED see Figure 2 4 Verify that any module that does not display a green Power LED is properly seated in the chassis backplane If
15. his device which are not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Industry Canada Notice This digital apparatus does not exceed the class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications Le pr sent appareil num rique n met pas de bruits radio lectriques d passant les limites applicables aux appareils num riques de la class A prescrites dans le R glement sur le brouillage radio lectrique dict par le minist re des Communications du Canada Class A ITE Notice WARNING This is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Clase A Aviso de ITE ADVERTENCIA Este es un producto de Clase A En un ambiente dom stico este producto puede causar interferencia de radio en cuyo caso puede ser requerido tomar medidas adecuadas Klasse A ITE Anmerkung WARNHINWEIS Dieses Produkt zahlt zur Klasse A Industriebereich In Wohnbereichen kann es hierdurch zu Funkst rungen kommen daher sollten angemessene Vorkehrungen zum Schutz getroffen werden Product Safety This product complies with the following UL 60950 CSA C22 2 No 60950 73 23 EEC EN 60950 IEC 60950 Seguridad del Producto El producto de Enterasys cumple con lo siguiente UL 60950 CSA C22 2 No 6
16. logy if such foreign produced direct product is subject to national security controls as identified on the U S Commerce Control List or iii if the direct product of the technology is a complete plant or any major component of a plant export to Country Groups D 1 or E 2 the direct product of the plant or a major component thereof if such foreign produced direct product is subject to national security controls as identified on the U S Commerce Control List or is subject to State Department controls under the U S Munitions List 5 UNITED STATES GOVERNMENT RESTRICTED RIGHTS The enclosed Program i was developed solely at private expense ii contains restricted computer software submitted with restricted rights in accordance with section 52 227 19 a through d of the Commercial Computer Software Restricted Rights Clause and its successors and iii in all respects is proprietary data belonging to Enterasys and or its suppliers For Department of Defense units the Program is considered commercial computer software in accordance with DFARS section 227 7202 3 and its successors and use duplication or disclosure by the Government is subject to restrictions set forth herein 6 DISCLAIMER OF WARRANTY EXCEPT FOR THOSE WARRANTIES EXPRESSLY PROVIDED TO YOU IN WRITING BY ENTERASYS ENTERASYS DISCLAIMS ALL WARRANTIES EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY SATISFACTORY QUALITY FITNESS FOR
17. m may be contained in firmware chips or other media BY INSTALLING OR OTHERWISE USING THE PROGRAM YOU REPRESENT THAT YOU ARE AUTHORIZED TO ACCEPT THESE TERMS ON BEHALF OF THE END USER IF THE END USER IS AN ENTITY ON WHOSE BEHALF YOU ARE AUTHORIZED TO ACT YOU AND YOUR SHALL BE DEEMED TO REFER TO SUCH ENTITY AND THAT YOU AGREE THAT YOU ARE BOUND BY THE TERMS OF THIS AGREEMENT WHICH INCLUDES AMONG OTHER PROVISIONS THE LICENSE THE DISCLAIMER OF WARRANTY AND THE LIMITATION OF LIABILITY IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT OR ARE NOT AUTHORIZED TO ENTER INTO THIS AGREEMENT ENTERASYS IS UNWILLING TO LICENSE THE PROGRAM TO YOU AND YOU AGREE TO RETURN THE UNOPENED PRODUCT TO ENTERASYS OR YOUR DEALER IF ANY WITHIN TEN 10 DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL REFUND IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT CONTACT ENTERASYS NETWORKS LEGAL DEPARTMENT AT 978 684 1000 You and Enterasys agree as follows 1 LICENSE You have the non exclusive and non transferable right to use only the one 1 copy of the Program provided in this package subject to the terms and conditions of this Agreement 2 RESTRICTIONS Except as otherwise authorized in writing by Enterasys You may not nor may You permit any third party to i Reverse engineer decompile disassemble or modify the Program in whole or in part including for reasons of error correction or interoperability except to the extent expressly permitted
18. nd of its serviceable life it cannot be disposed of as unsorted municipal waste It must be collected and treated separately 3 It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment 4 Itis the users responsibility to utilize the available collection system to ensure WEEE is properly treated For information about the available collection system please go to http www enterasys com services support or contact Enterasys Customer Support at 353 61 705586 Ireland VCCI Notice This is a class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment VCCI If this equipment is used in a domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corrective actions CORB EURES ERREA ERER VCCI DAY CEOS VIRZABMRNRE CT CORBtRERE CHAT S CBR HRLEVAMOTCEMHVES DOGE AIAR E AIDERINICTRDHOEKT BSMI EMC Statement Taiwan This is a class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures SARA EeP AWARE n CHENIER TRE Beka CEEP T SRASRE KE Aya tt SAS Declaration of Conformity Application of Council Directive s Manufacturer s Name Manufacturer s Add
19. onmenal Spetiicalons elena A 3 ERE Specie SIONS lai iaia ai A 3 Figures 2 1 Comens ofthe BL aS TORENT Rls alia ai 2 2 2 2 Contents pi the BL E9524ENT Ritssic siria ei iaia 2 2 2 3 Typical Configuration for a Mid Span Power Hub ii 2 4 2 4 Module Bank for the 8 Port and 24 Port Mid Span Power Hubs 2 5 Tables 3 1 TCU SCNT edicole 3 1 A 1 Physical and Mechanical Speciications scsscciniaeointicanmcsttr saute kanien aii A 2 A 2 LED States and Ther Dennis seniorien A 2 A 3 Physical and Environmental SpeelcalionNS pc ARRE A 3 About This Guide Purpose This guide provides information and procedures on hardware installation setup configuration and management of the Enterasys Networks 8 port and 24 port Mid Span Power Hubs Note This guide applies to the following products e BL 69108ENT which is a standalone 8 port chassis e BL 69524ENT which is the chassis complete with three eight port modules BL 69224ENT which is the chassis without modules Who Should Use This Guide Electrical Hazard Only qualified personnel should perform installation procedures Riesgo Electrico Solamente personal calificado debe realizar procedimientos de instalacion Elektrischer Gefahrenhinweis Installationen sollten nur durch ausgebildetes und qualifiziertes Personal vorgenommen werden This guide is intended for administrative and technical personnel responsible for installing and managing Enterasys Netwo
20. ower Input 1 000 to 10 000 feet Voltage 90 264 V autoranging 46 Hz 63 Hz Connector 3 pin with ground Chassis grounding yes Power supply single DC Port Power Output Power enabling IEEE 802 3af Power pins Unused pairs pins 4 5 7 8 Maximum power port 15 6 W Maximum power all ports active 24 ports at 15 6 W each Module to module isolation 1500 Vrms Overload protection If current reaches 400 450 mA for 300 400 milliseconds then the port shuts down Mid Span Power Hub User s Guide A 3 Specifications A 4
21. problems exist refer to the troubleshooting checklist in Chapter 3 Troubleshooting If you require assistance contact Enterasys Networks using one of the methods described in Getting Help on page xii 2 4 Installation and Connection Powering Up Figure 2 4 Module Bank for the 8 Port and 24 Port Mid Span Power Hubs Data In from Ethernet switch Power Data Out to device to be powered Detect Power Forwarding Blue Power Green Mid Span Power Hub User s Guide 2 5 Powering Up 2 6 Installation and Connection Troubleshooting Refer to Table 3 1 for a checklist of problems and recommended actions to resolve the problem If additional support is needed refer to Getting Help on page xii Table 3 1 Troubleshooting Checklist Problem Recommended Action Unit is plugged into the Enterasys Mid Span Power Hub but main power LED is off Verify the use of a good AC cable with a good ground connection Verify that the AC is hot and that voltage is between 100 VAC to 264 VAC 50 Hz to 60 Hz For the 24 Port Mid Span Power Hub if the internal fan is working there may be an internal circuitry fault or internal voltage that is out of specification If the fan is not working there may be an internal power supply fault Unit is plugged in and running but the fans are not working Verify that all fan openings are clear Verify that the metal case is not damaged
22. ress European Representative Address Conformance to Directive s Product Standards Equipment Type Environment 89 336 EEC 73 23 EEC Enterasys Networks Inc 50 Minuteman Road Andover MA 01810 USA Enterasys Networks Ltd Nexus House Newbury Business Park London Road Newbury Berkshire RG14 2PZ England EC Directive 89 336 EEC EN 55022 EN 61000 3 2 EN 61000 3 3 EN 55024 EC Directive 73 23 EEC EN 60950 Networking Equipment for use in a Commercial or Light Industrial Environment Enterasys Networks Inc declares that the equipment packaged with this notice conforms to the above directives ONE YEAR LIMITED WARRANTY Enterasys Networks warrants to the original consumer or purchaser that each of its products and all components thereof will be free from defects in material and or workmanship for a period of one year from the original factory shipment date Any warranty hereunder is extended to the original consumer or purchaser and is not assignable Enterasys Networks makes no express or implied warranties including but not limited to any implied warranty of merchantability or fitness for a particular purpose except as expressly set forth in this warranty In no event shall Enterasys Networks be liable for incidental or consequential damages costs or expenses arising out of or in connection with the performance of the product delivered hereunder Enterasys Networks will in no case cover damages arising
23. rks products To use this guide effectively you should have a working knowledge of Local Area Networking LAN concepts and wireless LAN access infrastructures In addition you should have e Aworking knowledge of basic electronics and mechanical assembly e Anunderstanding of local operating and troubleshooting procedures e An understanding of related local building codes Mid Span Power Hub User s Guide xi Document Conventions Document Conventions The following conventions are used in this guide Note Calls the reader s attention to any item of information that may be of special importance Caution Contains information essential to avoid damage to the equipment Precauci n Contiene informaci n esencial para prevenir da ar el equipo Achtung Verweif t auf wichtige Informationen zum Schutz gegen Besch digungen Electrical Hazard Warns against an action that could result in personal injury or death due to an electrical hazard Riesgo Electrico Advierte contra una acci n que pudiera resultar en lesi n corporal o la muerte debido a un riesgo el ctrico Elektrischer Gefahrenhinweis Warnung vor s mtlichen Handlungen die zu Verletzung von Personen oder Todesfallen hervorgerufen durch elektrische Spannung f hren k nnen Getting Help For additional support related to the Mid Span Power Hubs or this document contact Enterasys Networks using one of the following methods World Wide Web
24. siness hours Your books records accounts and hardware devices upon which the Program may be deployed to verify compliance with this Agreement including the verification of the license fees due and paid Enterasys and the use copying and deployment of the Program Enterasys right of examination shall be exercised reasonably in good faith and in a manner calculated to not unreasonably interfere with Your business In the event such audit discovers non compliance with this Agreement including copies of the Program made used or deployed in breach of this Agreement You shall promptly pay to Enterasys the appropriate license fees Enterasys reserves the right to be exercised in its sole discretion and without prior notice to terminate this license effective immediately for failure to comply with this Agreement Upon any such termination You shall immediately cease all use of the Program and shall return to Enterasys the Program and all copies of the Program 9 OWNERSHIP This is a license agreement and not an agreement for sale You acknowledge and agree that the Program constitutes trade secrets and or copyrighted material of Enterasys and or its suppliers You agree to implement reasonable security measures to protect such trade secrets and copyrighted material All right title and interest in and to the Program shall remain with Enterasys and or its suppliers All rights not specifically granted to You shall be reserved to Enterasys 10 ENFOR
25. trademarks or registered trademarks of Enterasys Networks Inc in the United States and other countries All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies Documentation URL http www enterasys com support manuals Documentacion URL http www enterasys com support manuals Dokumentation im internet http www enterasys com support manuals Regulatory Compliance Information Federal Communications Commission FCC Notice This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a class A digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment uses generates and can radiate radio frequency energy and if not installed in accordance with the operator s manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense WARNING Changes or modifications made to t
26. unenforceable the validity legality and enforceability of any of the remaining provisions shall not in any way be affected or impaired thereby and that provision shall be reformed construed and enforced to the maximum extent permissible Any such invalidity illegality or unenforceability in any jurisdiction shall not invalidate or render illegal or unenforceable such provision in any other jurisdiction 14 TERMINATION Enterasys may terminate this Agreement immediately upon Your breach of any of the terms and conditions of this Agreement Upon any such termination You shall immediately cease all use of the Program and shall return to Enterasys the Program and all copies of the Program viii Contents About This Guide FIR xi Who Should Uss This Gude all alia lai xi Pocumem Conranohs alberi xii CO E E A EEE E IE E A O TA E N xii Chapter 1 Introduction Funcions and iF SAS sarraie a 1 1 Porn madra aAA RA E 1 1 Chapter 2 Installation and Connection COMU A E E E E O E IR A E E 2 1 PIO T a E 2 2 Uone e e E I E A N EE E E IR E 2 3 Conmiguration Tora Mid Span Power Hub aac aa ia 2 3 Pol lalla 2 4 Chapter 3 Troubleshooting Appendix A Hardware Specifications Regulatory Compliance Standarde ira ara A 1 Product U ea aA A 1 Piace OE E E EAS AEE TE AE AITTE E REE O N E E E A PY A 1 Model BL TN miele Ela eee A 1 Model BLCISHMENT rei dalai ai A 2 PhysicaMechanical SpotiicalonS able A 2 LED oe aO MOE iii A 2 PhiysicalEnmir
Download Pdf Manuals
Related Search