Emerson KF240PRZ00 Owner's Manual
Contents
1. A 40 WATT MAX CANDELABRA 7 BULBS 3 GBS REVERSING WN WITCH oe a LIGHT FITTER SA _ Cr a THREADED is NIPPLE N LOWER E RUBBER GLASS WASHER 1 8 x 24 NUT METAL WASHEREQDZS DECORATIVE CAP l FINIAL NUT Figure 17 Setting Operating Frequency of Wall Control and Receiver Figure 18 Your wall control and receiver have code switches which must be set in one of 16 possible code combinations The four levers numbered 1 2 3 and 4 on the switches are factory set in the ON up position Change the switch settings as follows 1 Slide the four switch levers in the wall control to your choice of ON up or down positions Use a ball point pen or L small screwdriver and slide the levers firmly up or down oO In the receiver slide the four switch levers to the same positions as set in the wall control Make sure the levers on both switches are in the same positions otherwise the fan will not operate ANTENNA WIRE SWITCH CODE SWITCH Figure 18 Installation of Wall Control SINGLE POLE INSTALLATION Figure 19 FAN LIGHT WALL CONTROL BLACK ov NEUTRAL REMOTE CONTROL RECEIVER LOCATED WITHIN THE CEILING COVER Figure 19 1 Disconnect power at circuit breaker or remove fuse 2 Remove faceplate and screws from existing wall control Pull control out from the wall box Determine the hot wire and the load2. specifically approved for this fan could result in fire shock and personal injury A WARNING This product is designed to use only those parts supplied with this product and or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal injury or property damage INSTRUCTION TO THE USER if device contains a digital device This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to
3. wire and disconnect these wires from control Do not attempt to disconnect any wires not already connected to existing control 113 Before installing wall control place wall control in OFF mode by pushing ON OFF switch to the OFF position 13 4 BP7308 LORRAINE KF240 2 15 06 3 21 ee Page 14 A WARNING Do not connect any neutral white wire to this control Incorrect wiring will damage this control 14 C15 1 6 Connect one black wire of wall control to the hot wire Securely connect wires with wire connectors supplied Figure 20 Connect one black wire of wall switch to the load black wire in wall box Securely connect wires with wire connector supplied Screw wall control into wall box and install decorator style faceplate included Leave wall control in OFF mode until fan installation is completed Refer to page 5 and complete the ceiling fan installation Figure 20 EMERSON or Eo FAN LIGHT WALL CONTROL 3 WAY INSTALLATION On fan controlled by two different wall controls See Figures 21 and 22 g1 2 Disconnect power at circuit breaker or remove fuse At all wall box locations remove faceplates and screws from existing controls Pull controls out from wall boxes and determine which wall box contains the hot lead and which wall box contains the load wire Also identify traveler wires
4. HOW TO ORDER REPAIR PARTS WHEN ORDERING REPAIR PARTS ALWAYS GIVE THE FOLLOWING INFORMATION e PART NUMBER e NAME OF ITEM e PART DESCRIPTION e MODEL NUMBER The model number of your Fan will be found on a label attached to the top housing For repair parts phone 1 800 654 3545 18 4 BP7308 LORRAINE KF240 2 15 06 3 21 eh Page 19 Repair Parts Listing Part Numbers Description Hanger Pack Consisting of 761655 53 Hanger Bracket Hanger Ball Downrod 16 Parts Bag Containing 763046 Wire Connector 7 Threaded Stud 8 32 x 1 1 4 2 Knurled Knob 2 Lockwasher 2 Hairpin Clip Clevis Pin Screw Truss Head 10 24 x 8mm 16 Washer Flat 16 Screw Oval Head 1 4 20 x 13mm 11 Nut 1 8 27 Washer Flat Washer Rubber Wrench Hex Cover Ceiling 763004 PRZ Downrod Scroll Decorative 763007 PRZ Coupling Cover Decorative 763005 PRZ Lower Scroll Decorative 3 763006 PRZ Flange Set full set for one fan 763010 PRZ Blade Set full set for one fan 762635 16 Adapter Light Fitter 763013 PRZ Fitter Assembly Light 763014 Glass Lower 763016 Cap Decorative 763019 PRZ Nut Finial 763020 PRZ Harness Assembly Wiring 763023 Downrod 8 761631 63 Wall Control Fan Light 762348 1 Receiver Remote Control 762670 4 Owner s Manual BP7308 19 BP7308 LORRAINE KF240 2 15 06 3 21 eh Page 20 LIMITED WARRANTY What The Warranty Covers This warranty cove
5. of clearance from floor to blades 16 Place the ceiling cover over the Figure 11 downrod Then reinstall the hanger DDO ball Figure 10 on the downrod as follows Route the three 80 motor leads through the hanger ball and slide the hanger ball over the downrod Position the pin through the two holes in the downrod and align the hanger ball so the pin is captured AT LEAST in the groove in the top of the hanger ball Pull the hanger ball up tight against the pin and securely tighten the setscrew in the hanger ball A loose setscrew could create fan I DOR LZZZZZZS 7 FLOOR A wobble Figure 11 44 WARNING The outlet box and joist must be securely mounted and capable of supporting at least 50 Ibs Use only a U L outlet box listed as Acceptable for Fan Support PIN HANGER A WARNING CEILING COVER To reduce the risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for 117 The fan comes with blue black and Fan Support and use screws Figure 10 supplied with outlet box Most outlet i boxes commonly used for support of installing me fan measure UR light fixtures a not sceaptecls for approximately 6 to 9 inches above top fan support and may need to be of hanger ball downrod assembly Cut replaced Consult a qualified off excess leads and strip back electrician if in doubt insulation 1 2 from end of leads 1 18 You have now comp
6. the National Electrical Code if Local Codes do not exist The ceiling fan must be grounded as a precaution against possible electrical shock Electrical installation should be made or approved by a licensed electrician The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds Use only U L outlet boxes listed as Acceptable for Fan Support and use the mounting screws provided with the outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt The longer downrod furnished with the fan provides the minimum recommended floor to fan blade clearance for a 9 foot ceiling The 8 downrod supplied must be used for an 8 foot ceiling The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades Follow the recommended instructions for the proper method of wiring your ceiling fan If you do not know enough about electrical wiring have your fan installed by a licensed electrician NOTE This fan is suitable for use with solid state speed controls WARNING To reduce the risk of fire or electric shock this fan should only be used with fan speed control Model No UC7067RC manufactured by Rhine Electric Co Ltd WARNING This product is designed to use only those parts supplied with this product and
7. which are common to both wall boxes Disconnect wires from existing controls only Do not attempt to disconnect any wires not already connected to existing controls N13 Before installing wall control place wall control in OFF mode by pushing ON OFF switch to the OFF position A WARNING Do not connect any neutral white wire to this control Incorrect wiring will damage this control O 4 Install a wall control in the wall box containing the hot wire first Connect the black wire of the wall control to the hot wire Securely connect wires with wire connectors supplied 5 Connect one black wire of the wall control to both remaining traveler wires in the wall box and secure with wire connector supplied NOTE Retrofit 3 way installations are kely to include two traveler wires between the two wall boxes In new c onstruction only one traveler wire Is required 3 WAY WIRING DIAGRAM NEW CONSTRUCTION BLACK NEUTRAL REMOTE CONTROL RECEIVER LOCATED WITHIN THE CEILING COVEI WALL CONTROL WIRE Figure 21 g6 14 O 8 Place wall control into wall box Screw in place and install decorator style faceplate included 7 Next install the other wall control into the wall box containing the load wire Connect the black wire of the wall control to the traveler wire s already connected to the black wire in the oth
8. BP7308 LORRAINE KF240 2 15 06 3 21 eh Page 1 READ AND SAVE THESE INSTRUCTIONS Emerson Fans Designed by KICHLERVS EMERSON LORRAINE Ceiling Fan Owner s Manual Model Number KF240PRZ00 Parisian Bronze with Dark Cherry Walnut Blades Net Weight 27 0 Lbs Part No F40BP73080000 Form No BP7308 4 BP7308 LORRAINE KF240 2 15 06 3 21 nes Page 2 A WARNING WARNING To avoid fire shock and serious personal injury follow these instructions Safety Instructions Read your owner s manual carefully and keep it for future reference Before servicing or cleaning unit switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a warning device such as a tag to the service panel Be careful of the fan and blades when cleaning painting or working near the fan Always turn off the power to the ceiling fan before servicing Do not put anything into the fan blades while they are turning Do not operate reversing switch until fan blades have come to a complete stop Additional Safety Instructions for Installation To avoid possible shock be sure electricity is turned off at the fuse box before wiring and do not operate fan without blades The installation is to be in accordance with the National Electrical Code ANSI NFPA 70 1999 and Local Codes Use
9. G receiver fully into the hanger bracket To avoid possible fire or shock make Position the antenna wire on top of the sure that the electrical wires are receiver completely inside the outlet box and 4 Screw the two 1 1 4 threaded studs Lot aula erie a the ceiling supplied into the tapped holes in the g hanger oraret Figure 14 7 Screw in three 40 watt maximum 1 5 Lift the ceiling cover up to the threaded candelabra bulbs in the light fitter studs and turn until the studs protrude sockets Figure 17 Carefully place the through the holes in the ceiling cover lower glass over the light fitter threaded Figure 16 nipple Be sure the glass is firmly 16 Secure the ceiling cover in place by seated on the fitter then secure in 1 1 4 THREADED STUD 2 Figure 16 sliding lockwashers supplied over the threaded studs and installing the two knurled knobs supplied Figure 16 Tighten the knurled knobs securely until the ceiling cover fits snugly against the ceiling F ae COVER LOCKWASHER 2 ja KNURLED E3 KNOB 2 12 place using a rubber washer metal washer and 1 8 27 nut washers and nut are supplied 8 Place the decorative cap over the threaded nipple and then screw on the finial nut Figure 17 Your ceiling fan is now installed and wired to be controlled by your fan light wall control 4 BP7308 LORRAINE KF240 2 15 06 3 21 ee Page 13 X
10. WNROD HAIRPIN MOTOR COUPLING SETSCREW 2 SK Figure 8 13 Tighten the two upper setscrews Figure 8 securely while pulling up on the downrod NOTE The setscrews must be properly installed as described above or fan wobble could result 14 Position the three scrolls on the decorative coupling cover so that they are vertical then tighten the nuts on the inside of the coupling cover Make sure the grommet is properly installed in the decorative coupling cover then slide the coupling cover over the downrod until it rests on the motor housing Figure 9 NOTE If you installed the 8 downrod the decorative downrod scroll will not be installed Disregard step 15 and proceed to step 16 DECORATIVE DOWNROD SCROLL DECORATIVE COUPLING OVER A Figure 9 15 Using the hex wrench supplied unscrew the setscrew in the decorative downrod scroll collar until it clears the inside of the collar Slide the collar over the downrod Figure 9 until it rests on the coupling cover then tighten the setscrew 4 BP7308 LORRAINE KF240 2 15 06 3 21 nes Page 9 A WARNING How to Hang It is critical that the pin in the hanger ball Your Ceiling Fan is properly installed and the setscrew securely tightened Failure to verify that the pin and setscrew are properly installed could result in the fan falling 44 WARNING The fan must be hung with at least 7
11. box and box connectors must be of type required by the local code The minimum wire would be a 3 conductor 2 wire with ground of the following sizes Unpacking Instructions For your convenience check off boxes are provided next to each step As each step is completed place a check mark in the box This will insure that all steps have been completed and will be helpful in finding your place should you be interrupted NOTE If you are uncertain of part WARNING description refer to exploded view Do not install or use fan if any part is illustration damaged or missing Call Toll Free a Fan motor and housing assembly 1 800 654 3545 One decorative coupling cover assembly WARNING One ceiling cover This product is designed to use only One decorative downrod scroll those parts supplied with this product Five blade flanges and or any accessories designated Five fan blades specifically for use with this product by Emerson Electric Co Substitution of One light fitter adapter parts or accessories not designated for h One hanger bracket use with this product by Emerson Electric One hanger ball downrod 16 Co could result in personal injury or assembly property damage j One 8 downrod One lower glass g1 Open styrofoam unit containing fan One light fitter assembly Remove top half of styrofoam unit m One decorative cap Remove parts and check to see that 4 One finial nut you have receive
12. color to color before they can be engaged Make sure the connectors are engaged properly BP7308 LORRAINE KF240 2 15 06 3 21 nes Page 7 LIGHT FITTER ASSEMBLY LIGHT FITTER REMOVE AND RETAIN GONNECTOR THREE PAN HEAD SCREW LOCKWASHERS A MOTOR CONNECTOR Figure 4 8 Remove and retain the three outer screw lockwashers from the light fitter adapter Figure 4 Position the light fitter assembly on the light fitter adapter Line up the three holes on the light fitter with the threaded holes in the adapter and reinstall three screw lockwashers previously removed Figure 5 CAUTION Before installing and tightening the screws be sure there are no wires pinched between the light fitter and the light fitter adapter REINSTALL THREE PAN HEAD SCREW LOCKWASHERS LIGHT FITTER ASSEMBLY LIGHT FITTER ADAPTER N Figure 5 10 Position the top and bottom halves of the styrofoam packaging side by side on the floor with a six to eight inch gap between the halves Figure 6 Carefully place the partially assembl ed ceiling fan on the styrofoam halves with the light fitter assembly positioned in the gap and the fan assembly resting on the fan blade assemblies PARTIALLY ASSEMBLED FAN Figure 6 STYROFOAM PACKAGING 11 Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod Figure 7 Rem
13. crew in the hanger ball downrod assembly is loose Screws securing fan blade flanges to motor are loose Fan blade flanges not seated properly Hanger bracket and or ceiling outlet box is not securely fastened 6 Fan blades out of balance 17 1 Check main and branch circuit fuses or circuit breakers 4 WARNING Make sure main power is turned off Check line power connections to fan Turn ON Fan Light Wall Control Check that both code switches are set in the same positions Attach blades to fan before operating Check to make sure the screws which attach the blade flanges to the motor are tight Tighten screws securely Raise decorative downrod cover and coupling cover and tighten setscrews securely Tighten the setscrew in the hanger ball downrod assembly Check to be sure screws which attach the fan blade flanges to the motor are tight Check to be sure that the screws securing the fan blade flanges seat firmly Tighten the hanger bracket screws to the outlet box and or secure outlet box Interchanging an adjacent side by side blade pair can redistribute the weight and result in smoother operation Or use supplied balancing kit to balance blades BP7308 LORRAINE KF240 2 15 06 3 21 ee Page 18 Repair Parts 1 Ww A ap Before discarding packaging material be certain all parts have been removed
14. d the following parts One Fan Light Wall Control transmitter and receiver 4 BP7308 LORRAINE KF240 2 15 06 3 21 es Page 4 p One loose parts bag containing OVP CoN D T 8 9 10 11 12 Two 8 32 x 1 1 4 threaded studs Two knurled knobs Two lockwashers Seven wire connectors One clevis pin hairpin clip assembly Eleven 1 4 20 x 13mm oval head screws Sixteen 10 24 x 8mm truss head screws Sixteen flat washers One 1 8 27 nut One metal washer One rubber washer One hex wrench NOTE Place the parts from the loose parts bags in a small container to keep them from being lost 2 Remove the fan motor and housing assembly from the protective plastic bag Place the fan assembly into the lower foam pad with the bottom of the motor facing up The lower foam pad serves as a holder for the fan during the first stages of assembly orn A A BP7308 LORRAINE KF240 2 15 06 3 21 nes Page 5 Electrical Requirements IMPORTANT Your ceiling fan will not function properly and may be damaged if used with any wall dimmer switch or control other than the Emerson Electric Fan Light Wall Control supplied with the fan or an optional Emerson Electric SR100 Remote Control Your new ceiling fan will require a grounded electrical supply line of 120 volts AC 60 Hz 15 amp circuit The outlet box must be securely anchored and capable of withstand
15. er wall box Secure with wire connectors supplied Connect one black wire of the wall control to the load black wire and secure with wire connector supplied 4 BP7308 LORRAINE KF240 2 15 06 3 21 ee Page 15 Place the second wall control into the LI wall box Screw in place and install decorator style faceplate included m Leave switch in OFF mode until fan installation is completed 10 Refer to page 5 and complete the ceiling fan installation STANDARD WIRING FOR EXISTING 3 WAY CONTROL EXISTING WALL CONTROL LOAD HOT BLK FAN LIGHT WALL CONTROL TRAVELER WIRES LOAD Figure 22 Operating Your Ceiling Fan IMPORTANT Fan installation must be completed including the installation of the fan blades before testing of the remote control Your Fan Light Wall Control Figure 23 has full control of your fan and light However airflow direction is controlled by a slide switch on the light fitter 1 Restore electrical power to the outlet box by turning the electricity on at the service panel NOTE Make sure that the ON OFF slide switch on the Fan Light Wall Control is in the ON position O 2 To set the desired fan speed press the HI MED or LOW buttons to operate your fan on high medium or low speed Figure 23 15 To turn your fan off press the OFF button To set the level of light brightnes
16. except for the ground wire How to Wire Your Ceiling Fan If you feel that you do not have enough 2 electrical wiring knowledge or experience have your fan installed by a licensed electrician A WARNING Turning off wall switch is not sufficient To avoid possible electrical shock be sure electricity is turned off at the main fuse box before wiring All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock CAUTION To reduce the risk of electrical shock disconnect the electrical supply circuit before installing the fan light kit or receiver O1 Position the supply wires to the left side of the outlet box Figure 14 position the fan wires to the right side Partially insert the remote control receiver flat side up until one end rests on the hanger ball as shown in Figure 14 a Refer to Figures 14 and 15 and connect the receiver wires to the supply wires and the fan motor wires as follows Securely connect the green grounding wires from the hanger ball and the hanger bracket to the supply grounding conductor this may be a bare wire or a wire with green insulation b Securely connect the supply white neutral wire to the receiver white AC IN N wire Securely connect the supply black wire hot wire to the receiver black AC IN L wire d Securely connect the fan motor white wire t
17. ing a load of at least 50 pounds 4 WARNING To reduce the risk of fire electric shock or personal injury mount fan to outlet box marked Acceptable for Fan Support and use screws supplied with outlet box Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced Consult a qualified electrician if in doubt If your fan is to replace an existing ceiling light fixture turn electricity off at the main fuse or circuit breaker box at this time and remove the existing light fixture A WARNING Turning off wall switch is not sufficient To avoid possible electrical shock be sure electricity is turned off at the main fuse or circuit breaker box before wiring All wiring must be in accordance with National and Local codes and the ceiling precaution against possible electrical shock Ceiling Fan Procedures General Your Emerson ceiling fan comes supplied with a Fan Light Wall Control which consists of a wall control transmitter and a remote control receiver mounted under the ceiling cover This system allows you to regulate your ceiling fan speed and light intensity NOTE An optional Emerson Electric SR100 Remote Conirol may also be used to control your ceiling fan How to Assemble Your Ceiling Fan 4 WARNING Turning off wall switch is not sufficient To avoid possible electrical shock be sure electricity is turned off at the main f
18. leted the initial 4 Securely attach the hanger bracket to assembly of your new ceiling fan You the outlet box using the two screws can now proceed with hanging and supplied with the outlet box Figure 12 wiring your fan white leads that are 80 long Before a BP7308 LORRAINE KF240 2 15 06 3 21 ee Page 10 O A WARNING Hanger bracket must seat firmly against outlet box If the outlet box is recessed remove wall board until bracket contacts box If bracket and or outlet box are not securely attached the fan could wobble or OUTLET BOX TWO SCREWS SUPPLIED WITH OUTLET BOX HANGER BRACKET TAB Figure 12 2 Carefully lift the fan and seat the hanger ball downrod assembly on the hanger bracket that was just attached to the outlet box Figure 13 Be sure the groove in the ball is lined up with the tab on the hanger bracket Figure 12 A WARNING Failure to seat tab in groove could cause damage to electrical wires and possible shock or fire hazard NOTE CEILING COVER SUPPLY WIRES AND FAN WIRES OMITTED FOR CLARITY ar PI OUTLET i BOX HANGER BRACKET HANGER BALL DOWNROD ASSEMBLY Figure 13 A WARNING To avoid possible fire or shock do not pinch wires between the hanger ball downrod assembly and hanger bracket 10 BP7308 LORRAINE KF240 2 15 06 3 21 ee Page 11 including ground and that no bare wire is visible at the wire connectors
19. o the receiver white TO MOTOR N wire e Securely connect the fan motor black wire to the receiver red TO MOTOR L wire Securely connect the fan motor blue wire to the receiver blue FOR LIGHT wire 44 WARNING Check to see that all connections are tight including ground and that no bare wire is visible at the wire NOTE Make all wiring connections using wire connectors Supplied Make sure that all connections are tight connectors except for the ground wire Do not operate fan until blades are in place Noise and fan damage could result SUPPLY WHITE WIRE NEUTRAL J RECEIVER WHITE RE RECEIVER BLACK WIRE SUPPLY BLACK WIRE HOT GROUND WIRE RECEIVER RED WIRE RECEIVER BLUE WIRE GREEN GROUND WIRE FROM HANGER BALL ANTENNA GREEN GROUND WIRE FROM HANGER BRACKET 1 1 4 THREADED FAN WHITE WIRE STUD 2 RECEIVER WHITE WIRE Figure 14 11 4 BP7308 LORRAINE KF240 2 15 06 3 21 ee Page 12 SW101 FAN LIGHT WALL CONTROL SUPPLIED an BLACK A BLACK HOT So m 190 HOT z A y BLACK VOLT ii XY SUPPLY 2 WN WHITE y if WHITE GROUND RED U EE BLUE WHITE ABLE WITH GROUND ics Pe ioe BLACK GREEN WIRE GROUND BLUE FROM HANGER BALL AND WHITE HANGER BRACKET Figure 15 HANGER BALL 3 Push the wires and connectors up into the outlet box while inserting the 4 WARNIN
20. or any accessories designated specifically for use with this product by Emerson Electric Co Substitution of parts or accessories not designated for use with this product by Emerson Electric Co could result in personal injury or property damage WARNING To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades WARNING To reduce the risk of electrical shock this fan must be installed with an isolating wall control switch DATE CODE The date code of this fan may be found on the box stamped in ink on a white label You should record this data above and keep it in a safe place for future use 4 BP7308 LORRAINE KF240 2 15 06 3 21 nes Page 3 This Manual Is Designed to Make it as Easy as Possible for You to Assemble Install Operate and Maintain Your Ceiling Fan Tools Needed for Assembly Installed Wire Length Wire Size A W G One Phillips head screwdriver Up to 50 ft 14 One wire stripper 50 100 ft 12 One pair of pliers One stepladder Seven wire connectors supplied Three 40 watt maximum Candelabra WARNING bulbs Before assembling your ceiling fan refer to section on proper method of wiring Materials your fan page 11 If you feel you do not have enough wiring knowledge or experience have your fan installed by a licensed electrician Wiring outlet
21. ove the pin from the downrod then remove the hanger ball Retain the pin and hanger ball for reinstallation in step 16 PIN HANGER BALL DOWNROD Figure 7 NOTE If you have an eight foot ceiling you will have to use the 8 downrod supplied in order to maintain the necessary blade to floor clearance of seven feet 4 BP7308 LORRAINE KF240 2 15 06 3 21 nes Page 8 12 Unscrew the two upper setscrews Figure 8 until they clear the inside of the motor coupling Then separate untwist and unkink the three 80 motor leads Route the motor lead wires through the downrod Align the clevis pin holes in the downrod with the holes in the motor coupling Install the clevis pin and secure with the hairpin clip Figure 8 The clevis pin must go through the holes in the motor coupling and the holes in the downrod Be sure to push the straight leg of the hairpin clip through the hole near the end of the clevis pin until the curved portion of the hairpin clip snaps around the clevis pin The hairpin clip must be properly installed to prevent the clevis pin from working loose Pull up on the downrod to make sure the clevis pin is properly installed A WARNING It is critical that the clevis pin in the motor coupling is properly installed and the setscrew securely tightened Failure to verify that the pin and setscrew are properly installed as shown in Figure 8 could result in the fan falling DO
22. roduct to the factory obtain a return authorization and service identification tag by writing to Air Comfort Products Division of Emerson Electric Co 8100 W Florissant Ave St Louis MO 63136 Include all model numbers shown on the product with your request e To return the product to an authorized service center call 1 800 654 3545 for the address of the nearest authorized service center You will be responsible for all insurance freight or other transportation charges to our factory or authorized service center Your Emerson Air Comfort Ceiling Fan should be properly packed to avoid damage in transit since we will not be responsible for any such damage What Is Not Covered The glass globes and light bulbs of your ceiling fan are not covered by this warranty This warranty also does not cover any defects malfunctions or failures caused by e Repairs by persons not authorized by Emerson Electric Co e Use of parts or accessories not authorized by Emerson Electric Co e Mishandling improper installation modifications or damage to your ceiling fan while in your possession or e Unreasonable use misuse abuse including failing to do reasonable and necessary maintenance and normal wear and tear e Additionally this warranty and any implied warranty of merchantability or fitness for a particular purpose are voided when e The original purchaser or user ceases to own the product or e The fan is moved from its original point of in
23. rs the motor and the other components and accessories of your Emerson Electric Co ceiling fan against all defects in workmanship and materials You must be the original purchaser or user of the product to be covered What The Period Of Coverage Is As it applies to the motor this warranty will last for a lifetime of your ceiling fan All other components and accessories are covered by this warranty for one year from the date you purchased your ceiling fan ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE MADE WITH RESPECT TO COMPONENTS AND ACCESSORIES IS ALSO LIMITED TO ONE YEAR What Will Emerson Electric Co Do To Correct Problems Emerson Electric Co will replace a defective Emerson Air Comfort Ceiling Fan motor blade component or other accessory at no charge to you If repair of the motor or blades is not practical or possible within a reasonable time and no replacement can be provided Emerson Electric Co will refund the actual purchase price of your fan We will ship the repaired product or replacement to you at no charge but you are responsible for all costs or removal reinstallation and shipping of the product to Emerson Electric Co How Can You Get Service YOU MUST HAVE PROOF OF YOUR PURCHASE OF THE CEILING FAN TO OBTAIN LIMITED WARRANTY SERVICE KEEP YOUR RECEIPT OR OTHER PROOF OF PURCHASE You can return the product to our factory or to your nearest authorized service center e To return the p
24. s press and hold the LIGHT button The light brightness will continue to increase then decrease while the button is held down When the light is at the desired brightness release the button To turn the light on and off press and release the LIGHT button The light will turn on at the light level previously set see step 4 If airflow is desired in the opposite direction turn the fan off and wait for the blades to stop turning Remove the lower glass Figure 17 then slide the reversing switch located on the light fitter to the opposite position and turn the fan on again The blades will turn in the opposite direction and reverse the airflow EMERSON Figure 23 4 BP7308 LORRAINE KF240 2 15 06 3 21 ee Page 16 Maintenance IMPORTANT CARE INSTRUCTIONS LI for your Ceiling Fan Periodic cleaning of your new ceiling fan is O the only maintenance that is needed When cleaning use only a soft brush or lint free cloth to avoid scratching the finish _ 2 Accessories Downrod Extension Kits see store or catalog Ceiling Fan Controls see store or catalog A WARNING The use of any other control not Abrasive cleaning agents are not required and should be avoided to prevent damage to finish A WARNING Do not use water when cleaning your ceiling fan It could damage the motor or the blades and create the possibility of an electrical shock
25. stallation This warranty is only valid within the 50 states of the United States and the District of Columbia No other written or oral warranties apply and no employee agent dealer or other person is authorized to give any warranties on behalf of Emerson Electric Co REPAIR REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE UNDER THIS WARRANTY AND EMERSON ELECTRIC CO IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND INCLUDING INCIDENTAL AND CONSEQUENTIAL DAMAGES Incidental damages include but are not limited to such damages as loss of time and loss of use Consequential damages include but are not limited to the cost of repairing or replacing other property which was damaged if this product does not work properly How State Law Relates To The Warranty Some states do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state A EMERSON Air Comfort Products DIVISION OF EMERSON ELECTRIC CO 8100 W Florissant St Louis MO 63136 Part No F40BP73080000 Printed in China 02 06 Form No BP7308 4
26. tion the blade flange on the motor hub so that the mounting holes in the blades flange align with the two threaded holes in the motor hub Figure 2 Securely install two 1 4 20 x 13mm oval head screws supplied Repeat this procedure for the remaining four blade assemblies REMOVE AND RETAIN ONE PAN HEAD SCREW LOCKWASHER LOOSEN TWO PAN HEAD SCREWS MOTOR FLANGE 1 4 20 x 13mm OVAL HEAD SCREWS 2 BLADE FLANGE MOTOR HUB Figure 2 5 4 Remove and retain one of the three pan head screw lockwashers from the motor flange Figure 2 loosen the other two pan head screws three or four turns Position the light fitter adapter on the motor flange so that the two screws mate with the two keyhole slots in the light fitter adapter Figure 3 NOTE Make sure that the lockwashers are positioned between the screw head and the light fitter adapter REINSTALL ONE PAN HEAD SCREW LOCKWASHER LIGHT FITTER SS Ya EE TIGHTEN TWO PAN Lx HEAD SCREWS N Figure 3 6 Turn the light fitter adapter clockwise and tighten both screws Figure 3 Reinstall the other pan head screw lockwasher previously remov ed in the remaining hole in the light fitter adapter 7 Carefully rest the light fitter assembly on the adapter then engage the light fitter connector with the motor connector Figure 4 The two connectors are keyed and color coded and must be mated correctly
27. use or circuit breaker box before wiring All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock IMPORTANT Before assembling your ceiling fan refer to sections Setting Operating Frequency of Wall Control and Receiver and Installation of Wall Control page 13 These sections instruct you how to a Set the operating frequency of the fan light wall control and the remote control receiver and b Install the fan light wall control in the wall box You will then be ready to proceed with the assembly and installation of your ceiling fan as follows fan must be properly grounded as a 4_ Mount the fan blades to the blade flanges using three 10 24 x 8mm truss head screws and three flat washers screws and washers supplied Figure 1 A WARNING To reduce the risk of personal injury do not bend the blade flange when installing the blade flanges balancing the blades or cleaning the fan Do not insert foreign objects in between rotating fan blades BP7308 LORRAINE KF240 2 15 06 3 21 nes Page 6 10 24 x 8mm TRUSS HEAD ex SCREWS 3 o FAT WASHERS 3 FAN BLADE Figure 1 BLADE FLANGE 2 Remove and discard the four shipping retainers securing the motor hub in the motor housing NOTE Take care not to scratch the fan housing when installing the blade assemblies 3 Posi
28. which the receiver is connected Consult the dealer or an experienced radio TV technician for help This equipment has been certified to comply with the limits for a Class B computing device pursuant to FCC Rules In order to maintain compliance with FCC regulations shielded cables must be used with this equipment Operation with non approved equipment or unshielded cables is likely to result in interference to radio and TV reception The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user s authority to operate this equipment This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations 16 BP7308 LORRAINE KF240 2 15 06 3 21 ee Page 17 4 WARNING FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN 1 Fan will not start 2 Fan sounds noisy 3 Fan wobbles excessively Trouble Shooting PROBABLE CAUSE SUGGESTED REMEDY 1 Fuse or circuit breaker blown Loose power line connections to the fan Fan Light Wall Control is OFF Code switches in remote control receiver and Fan Light Wall Control are not set in the same position Blades not attached to fan Screws securing fan blade flanges to motor are loose Screws holding blades to flanges are loose Setscrews in motor coupling are not tightened securely Sets
Download Pdf Manuals
Related Search