Elmo TNC4604 User's Manual
Contents
1. E E MC CCD COLOR VIDEO CAMERA CCD COLOR VIDEO CAMERA TNC4604 INSTRUCTION MANUAL A RISK OF ELECTRIC SHOCK A DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance CAUTION Do not use any power supply other than specified WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE The CAUTION label is attached on the bottom of camera an equilateral triangle is intended to alert the user INFORMATION This equipment has been tested and found to comply with the limits for Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates use and can radiate radio frequency energy and if not installed and used in accordance with2. V Scanning system 2 1 interlaced Scanning frequency H V 15 734kHz 60Hz Sync system Internal Line lock Internal Resolution 480 TV lines Horizontal 350 TV lines Vertical Recommended illumination AGC 50 Ix F1 2 under incandescent lamp Built in Factory set at ON White balance Auto Manual Factory set at AUTO Backlight control Built in Factory set at OFF AES Automatic Electronic Shutter Built in Factory set at OFF Output signal Auto iris terminal VBS 1 0 Vp p 75 NTSC compatible 4P DC Video Power terminal 2P terminal Lens mount CS Ambient temperature 10 C 50 C 14 F 122 F Ambient humidity 30 90 Dimensions 60 W x 60 H x 90 D mm 2 4 x 2 4 x 3 5 inches Weight 300grm 0 7Ibs Note Weight and dimensions are approximate Design and specifications are subject to change without prior notice PRECAUTIONS FOR USE AND INSTALLATION Never aim the camera at the sun Never aim or point the camera at the sun even if you are not shooting Do not shoot intense light Strong light such as a spot light on the image plane will cause blooming or smear When strong light comes into the image plane vertical stripes may appear on it However this does not mean that the camera is defect Take precautions when handling a camera Do not drop your camera or give it a stro
3. down W button will make the delay time of vertical sync phase against the phase of power frequency longer Use the push button 8 if the picture image on a monitor TV may flow when using the camera in combination with other camera s controlled by the Line Lock synchronization In this case get a proper image by shifting the phase of vertical sync signal of the camera against that of the other If a proper image cannot be obtained even after this adjustment reset the potentiometer to its original position and use the function control potentiometer of the other camera to shift the phase of vertical sync signal of other camera Caution Before making adjustment make sure that cameras have their power supplies connected with the same polarity not 180 apart e Manual white balance selector When the white balance selector is set to MANU shift change in 4 above the white balance can be adjusted by using the PUSH switch This mode will prove effective under shooting conditions with little variation in color temperture When the white balance selector is set to MANU shift change the vertical sync phase can not be adjusted SPECIFICATION Model TNC4604 Power source DC12V DC11V 35V AC24V ACI5V 27V 60Hz 0 5Hz Power consumption Approx 3 7W Approx 3 5W Pick up device 1 3 Color interline transfer CCD Effective picture element 768 H x 494 V Scanning area 4 88mm H x 3 66mm
4. noise 4 White balance selector Manual or Automatic white balance modes are selectable With the setting at AUTO position the camera automatically adjusts to the color temperature and adjusts the white balance The camera is factory set at AUTO position For manual adjustment set to MANU position and set the white balance switches as follows White balance WB According to the combination of the switches 1 and 2 the following adjustments are available Can be adjusted by the AWB PUSH switch Manual Shift change Manual Fixed 3200k Manual Fixed 4200k IRIS switch When a DC driven type auto iris lens is used set this switch to DC position When a video feedback type auto iris lens is used set this switch to VIDEO position ALC LEVEL Adjust video output level when IRIS switch is DC position AES switch Automatic Electronic Shutter With the AGC switch at ON position AES are available By setting the AES switch Automatic Electronic Shutter mode 1 60 1 10 000 sec is available Note In electronic shutter mode Sufficient brightness is required The picture will flicker when shooting under the illumination produced by fluorescent lamp PUSH button e Vertical sync phase adjustment Vertical sync phase adjusting is set at the position fully that the delay time of vertical sync phase against the phase of power frequency is shortest when shipped from the factory Select this up A and
5. CAMERA CONTROLS Q AGC switch In case of necessity set the AGC switch to OFF position BLC Black Light Control switch With the AGC switch at ON position BLC are available In case the back lighting is too bright to shoot the main object clearly set this switch to ON position INTILL switch e INT internal control switch Monitor TV When the internal synchronization is used CAMERA set the switch to the INT side ie DC 12V power supply To AC 24V power supply Monitor TV e L L Line lock control switch Matching the vertical synchronization with the power frequency is called the line lock When the AC24V power supply is used set the switch to the LL side When two or more cameras are switched by the video switcher to a monitor TV the vertical sync phase can be locked with the power frequency and a stable vertical sync is obtained without being disturbed at the time of switching Caution 1 The camera is synchronized to the power frequency of 60Hz 0 5Hz covering a normal fluctuation of the power frequency The camera may not compensate for large fluctuation caused by power generated by an engine generator etc 2 It takes about 10 seconds or more to obtain a stable synchronization after the power is CAMERA Video output To AC 24V power supply CAMERA 2 4 turned on This is necessary to stabilize the camera against the power
6. es a need for service Replacement Parts When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part Unauthorized substitutions may result in fire electric shock or other hazards Safety Check Upon completion of any service or repairs to this video product ask the service technician to perform safety checks to determine that the video product is in proper operating condition PART NAMES AND FUNCTIONS All dimensions in mm inch O Lens mount Mount a CS mount lens 2 Camera mount For mounting a camera on wall housing etc 1 4 20UNC thread 8 Focusing dial For fine adjustment of the lens back focus IRIS terminal Connect when an automatic iris lens is used 5 VIDEO OUT terminal Connect to a monitor TV etc BNC connector AC power terminal Connect this to the AC24V 60Hz or DC12V power supply DC12V mE AC24V 1 2 D Ground terminal Connect this to the ground wire of the power supply cord Camera control switches Refer to CAMERA CONTROLS on page 4 HOW TO CONNECT 1 Before connection make sure that power of all units are OFF and cords are unplugged 2 Mount a lens onto the camera Refer to HOW TO USE for usable le
7. focus remains constant throughout the zooming range Note When weight of the lens is more than 1kg 2 2Ibs the camera should be supported by the lens rather than relying on camera mounting screw Adjust the back focus only when necessary Using an auto iris lens When a DC driven type auto iris lens is used set the AUTO IRIS switch at DC and connect the plug of the lens for iris terminal to the IRIS terminal on the right side of the camera When a video feedback type auto iris lens is used set the AUTO IRIS switch at VIDEO and connect the plug of the lens for iris terminal to the IRIS terminal on the right side of the camera Refer to Lens manual for the level adjustment DC position VIDEO position Control 9V iris power 50mA Max Control GND Drive 0 8Vp p auto iris video signal Plug for IRIS terminal CHUOMUSEN E4 191J 150 Soldering side Drive GND GND When a video feedback type auto iris lens peak average selectable type is used at peak mode BLC may not function well In such a case select the average mode 2 Before your use of the camera at AES Automatic Electronic Shutter mode When using an auto iris lens set the AES switch at OFF The AES switch is set at OFF when shipped from factory The AES mode may increase smears on monitors which is caused by characteristics of CCD and is not defect Set the AES switch at OFF in case smears appear excessively 3
8. mera The socket outlet should be installed near the equipment and should be easily accessible 6 14 Meizen cho Mizuho ku Nagoya 467 8567 Japan ELMO Europe G m b H Neanderstr 18 40233 Dusseldorf Germany Tel 0211 376051 53 Fax 0211 376630 E mail elmoeurope AOL com Web http www elmo de Printed in CHINA
9. ng shook or vibration This may cause camera to malfunction Do not touch internal parts Be sure not to touch the internal parts This may cause to electrical shock Do not let the camera get wet Install the camera at the place where it will not get wet Should it gets wet turn off the power immediately and contact your dealer Ef f710 ELMO CO LTD OVERSEAS SUBSIDIARY COMPANIES ELMO Mfg Corp 1478 Old Country Road Plainview NY 11803 5034 U S A Tel 516 501 1400 Fax 516 501 0429 E mail elmo elmousa com Web http www elmousa com 6X1NHFF02 Ontario L6T 3T6 Canada Tel 905 453 7880 Fax 905 453 2391 ELMO Canada Mfg Corp 44 West Drive Brampton E mail info elmocanada com Web http www elmocanada com Install your camera where no video noise appears When camera cables have been laid near electric wires or television receivers a noise may interfere the image If noise occurs relocate cables or reinstall equipment Check the ambient temperature and humidity Avoid using camera in areas where temperature is consistently hotter or colder than the specified range See Specifications chart below or poor image quality or damaged parts may occur Precautions should also be taken to avoid areas of high humidity Should you notice any trouble If any trouble occurs while you are using the camera turn off the camera and contact your dealer Failure to do so may cause damage to the ca
10. njury to a child or adult and serious damage to the appliance Use only with stand tripod bracket or table recommended by the manufacturer or sold with the video product Any mounting of the appliance should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer Ventilation This video product should never be placed near or over a radiator or heat register This video product should not be placed in a built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to Power Sources This video product should be operated only from the type of power source indicated on the marking label Tf you are not sure of the type of power supply to your location consult your appliance dealer or local power company Power Cord Protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs screws and the point where they exit from the appliance 12 13 14 15 16 17 18 Lightning For added protection for this video product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the wall outlet and disconnect the power supply and cable system This will prevent damage to the video product due to lightning and power line s
11. ns 3 Connect video terminal of the camera and the video input terminal of a monitor TV etc with a 75Q coaxial cable 4 Connect the power terminal of the camera to a power supply Caution Installation should be made by a qualified service personnel and should conform to all local codes Lens coaxial cable for video signal and power supply are not supplied with a camera 2 HOW TO USE 1 Adjust the iris and focus of the lens so that optimum image CS mount may be obtained tens 4mm or less Usable lenses CS mount lenses whose length L in the illustration Camera R from the bearing surface of the mount is 4mm or less if Focusing dial protruded should be used Using the zoom lens adjustment of the back focus The camera is set at the standard back focus position when shipped from factory Depending on types of zoom lenses however slight readjustment may be necessary Adjust the lens back focus by turning the focusing dial in either direction as per the illustration referring to the following instructions Place an object at any fixed distance and set the focus ring of the zoom lens accordingly Set the zoom lens to full TELE position and obtain the best focus position by turning the focus ring or the zoom lens Set the zoom lens to full WIDE position and obtain the best focus position by turning the focusing dial located on the side of the camera Repeat procedures 2 and 3 until
12. the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense USER INSTALLER CAUTION Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party responsible for compliance to Part of the FCC Rules IMPORTANT SAFEGUARDS 10 11 Read Instructions All the Safety and operating instructions should be read before the appliance is operated Retain Instructions The safety instructions and instruction manual should be retained for future reference Heed Warnings All warnings on the appliance and in the instruction manual should be adhered to Follow Instructions All operating and use instructions should be followed Cleaning Disconnect this video product from the power supply before cleaning Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards Water and Moisture Do not use this video product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like Accessories Do not place this video product on an unstable cart stand tripod bracket or table The video product may fall causing serious i
13. urges Overloading Do not overload power supply and extension cords as this can result in a risk of fire or electric shock Object and Liquid Entry Never push objects of any kind into this video product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electrical shock Never spill liquid of kind on the video product Servicing Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel Damage Requiring Service Disconnect this video product from the power supply and refer servicing to qualified service personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the video product c If the video product has been exposed to rain or water d If the video product does not operate normally by following the operating instructions in the instruction manual Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation e If the video product has been dropped or the cabinet has been damaged f When the video product exhibits a distinct change in performance this indicat
Download Pdf Manuals
Related Search