Electrolux FAVORIT 40650 User's Manual
Contents
1. To change a dishwashing cycle As long as the cycle has not yet started you can still change the dish washing cycle First cancel the dishwashing cycle then re set the time delay lastly select the new dishwashing cycle Switching Off the dishwasher Do not switch off the dishwasher until the indicator for the end of the dishwasher cycle is illuminated in the cycle progress display 1 Press the ON OFF button All display indicators will go out 2 Turn off the water tap Carefully open the door Hot steam may escape Hot dishes are sensitive to knocks Therefore leave the dishes to cool for about 15 minutes before removing them You also get a better drying result Removing the Dishes liJ It is normal for the inner door and the dispensers to be damp e Empty the lower basket first then the upper basket This way you avoid dripping water from the upper basket onto dishes in the lower basket Care and cleaning A Do not use furniture care products or aggressive cleaners e When necessary clean the dishwasher s controls with a soft cloth e Occasionally check the internal dispensers door seal and water inlet filter if fitted for dirt and clean them if necessary Cleaning the Filters liJ The filters must be regularly checked and cleaned Dirty filters will spoil the wash results Open the door and remove the lower basket 2 Turn the handle about 1 4 of a turn anticlockwise A and remove the fil2. Warning Sharp knives and other items of cutlery with sharp edges must be laid in the cutlery rack or in the upper basket to avoid the risk of injury AN To ensure that all items of cutlery in the cutlery basket can be reached by the water you should 1 Place the grid insert on the cut 2 Place forks and spoons in the cutlery basket s grid insert with lery basket their handles pointing down wards such as whisks leave off one half of the cutlery grid For larger utensils 14 Pots Pans Large Plates Load larger and heavily soiled dishes and pans in the lower basket Max diameter for plates 29 cm To make it easier to load larger dish es the two plate racks on the right in the lower basket can be folded down DOO SEM 22N SSS ONNE Nee 0000000000022 15 Cups Glasses Coffee Service Load smaller fragile crockery and long sharp cutlery in the upper bas ket e Arrange items of crockery on and under the folding cup racks so that they are offset from each other and water can reach all items e The cup racks can be folded up out of the way for tall crockery items e Lay or hang wine and brandy glasses in the slots in the cup
3. gt wo ee eee eee teen eel eel ceed ae 60 g normally soiled SATS saucepans Q s S se NORMAT oust EAEE ee ice and x e e e e e A 1 1 65 dried on food remains a S cookware 8 oe S Dinner serv ice and eles e ECO cookware r So Ta E e e e e e 50 temperature normally soiled S 2 sensitive TIRS dishes 1 The consumption values were obtained under standardised conditions They depend on how full the baskets for the dishes are Variations are therefore possible in practice 2 During the final rinse the temperature is increased to 68 for 10 minutes to disinfect e g ba bies bottles 3 When using this cycle only load the dishwasher half full 4 Test programme for Test Institutes Starting a Dishwashing Cycle G N N is 1 Check that the spray arms can turn freely 2 Turn the water tap on fully 3 Close the door 4 Press the ON OFF button 5 Select the desired cycle The programme display lights up One or two lights will flash in the programme progress display The selected cycle will begin after approximately 3 seconds Interrupting or Cancelling a dishwashing cycle Interrupt a dishwashing cycle that is in progress if it is absolutely nec essary Interrupting the dishwashing programme by opening the dishwash er door Hot steam may escape when the door is opened There is a risk of scald ing Open the door carefully The dishwashing cycle will stop
4. racks Adding Detergent N If the lid is closed Place the detergent in the detergent Close the lid and press until it locks Detergents remove the dirt from dishes and cutlery The detergent must be added before N the cycle starts Only use detergent intended for do D mestic dishwashers The detergent compartment is lo WW cated on the inside of the door Press the release button The lid will spring open a dispenser The markings indicate the dosing levels for powder detergents 20 30 corresponds to approx 20 30 ml of detergent Follow the manufacturer s instruc tions with regard to dosing and storage into place In the case of very heavily soiled dishes fill the adjoining compart ment 1 with additional detergent This detergent comes into use during the pre wash cycle 17 G Concentrated detergents Today s detergents for dishwashers are almost exclusively low alkaline concentrated detergents with natural enzymes in tablet or powder form Using 50 C dishwashing cycles in conjunction with these concentrated detergents reduces pollution and is good for your dishes as these dish washing cycles are specially matched to the dirt dissolving properties of the enzymes in concentrated detergents It is for this reason that us ing 50 C dishwashing cycles in conjunction with concentrated deter gents can achieve the same cleaning res
5. surface supplied with it must be re mounted liJ The plinth on free standing appliances is not adjustable 31 32 Connecting the dishwasher Connecting to the water supply e The dishwasher can be connected to cold and hot water supplies up to max 60 C e The dishwasher must not be connected to open hot water appliances or instantaneous water heaters Permitted water pressure Lowest permitted water pressure Consult your plumber if the water pres 1 bar 10 N em2 100 kPa sure is less than 1 bar If the water pressure is greater than 10 bar a pressure reduction valve must be used available from your dealer Highest permitted water pressure 10 bar 100 N cm2 1 MPa Connecting the inlet hose Z The water inlet hose must not be kinked crushed or entangled when it is being connected Connect the threaded hose fitting ISO 228 1 2000 on the water inlet hose to a tap with an external thread 34 inch The inlet hose is fitted with either a plastic or a metal nut Only tighten the plastic nut hand tight You must tighten the metal nut using a tool Then do a visual check for water tightness make sure that the tap is not dripping liJ So that access to the tap in the kitchen is not restricted by the use of the dishwasher we recommend installing an additional tap or fitting a T branch to the existing tap If you need a longer water inlet hose than that supplied the following VDE approved
6. 219899 37 38 Service and Spare Parts If the event of your appliance requiring service or if you wish to pur chase spare parts please contact Service Force by telephoning 0870 5 929 929 Your telephone call will be automatically routed to the Service Force Centre covering your post code area For the address of your local Service Force Centre and further informa tion about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you have read the details under the heading What to do if When you contact the Service Force Centre you will need to give the following details 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 The model and serial number of the appliance found on the rating plate 5 The purchase date Please note that a valid purchase re ceipt or guarantee documentation is required for in guarantee service calls Customer Care For general enquiries concerning your AEG appliance or for further information on AEG products please contact our Customer Care Depart ment by letter or telephone at the address below or visit our website at www aeg co uk Customer Care Department For Customer Service in the Republic AEG Domestic Appliances of Ireland please contact us at the ad 55 77 High Street dress below Slough AEG Electrolux Group I
7. Close the door The cycle will continue Cancelling the dishwashing cycle Press function buttons 2 and 3 and keep them pressed The programme display for the current cycle will flash for several sec onds and then go out Release the function buttons The dishwashing cycle has been can celled If you want to start a new cycle check whether there is any detergent in the dispenser Turning off the dishwasher will only interrupt a selected dishwashing cycle not cancel it The cycle will recommence after turning the dish washer back on again Setting the Delay Timer 20 Using the delay timer you can delay the start of a dishwashing cycle for 3 6 or 9 hours 1 Press the ON OFF button 2 Press the Delay Timer button repeatedly until the indicator next to the number of hours for which the start of the dishwashing cycle is to be delayed lights up e g 6h if the cycle is to start in 6 hours Select dishwashing cycle The LED indicator for the programme selected and the indicator next to the number of hours will light up The dishwashing cycle will start automatically following a countdown of the hours set is To change the time delay As long as the cycle has not yet started you can still change the setting by pressing the DELAY TIMER button Cancelling the delay timer Press the DELAY TIMER button repeatedly until none of the three time displays is lit The selected dishwashing cycle will begin immediately
8. The dishwasher must be installed on a firm floor and adjusted to en sure that it is stable and level in all directions e To compensate for unevenness in i the floor and to match the height of the appliance to that of sur rounding units extend the thread ed feet using a screwdriver e The drain hose inlet hose and mains cable must be laid so that they are able to move freely within the plinth area and so that they are not kinked or crushed when the dishwasher is in position e The dishwasher must also be w a K f on screwed tightly to the work surface or to the adjoining units This is essential to ensure the dishwasher does not tip up Free standing appliances Z If the dishwasher is installed directly next to a cooker a heat insulat ing non flammable panel laminated with aluminium foil on the side next to the cooker must be fitted flush with the top edge of the work surface depth 57 5 cm If the appliance is built in under a kitchen work surface the worktop supplied with the dishwasher can be removed in the following way Unscrew the screws from the elbows at the rear 1 2 Push the appliance s worktop back wards about 1 cm 2 oo Lift the worktop at the front 3 and 3 remove it Z Z A If the dishwasher is later used as a free standing appliance the work
9. ap m water mains water mains socket mains cable inlet cable drainage Warranty conditions Great Britain Standard guarantee conditions We AEG undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials we will at our discretion repair or replace the same FREE OF CHARGE for labour materials or carriage on condition that e The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate e The appliance has been used for normal domestic purposes only and in accordance with the manufacturer s operating and maintenance instructions e The appliance has not been serviced maintained repaired taken apart or tampered with by any person not authorised by us e All service work under this guarantee must be undertaken by a Service Force Centre Any appli ance or defective part replaced shall become the Company s property e This guarantee is in addition to your statutory and other legal rights e Home visits are made between 8 30am and 5 30pm Monday to Friday Visits may be available outside these hours in which case a premium will be charged Exclusions This guarantee does not cover e Damage or calls resulting from transportation improper use or neglect the replacement of any light bulbs or removable parts of glass or plastic e Costs incurred for calls to
10. is not plugged in A fuse in the house s wiring system is defective For dishwasher models with a delay start timer A start time has been select ed The dishwashing compart ment is made from rust free stainless steel Rust spots in the dishwashing compart ment are due to rust parti cles from external sources rust particles from water pipes pans cutlery etc Remove such spots with a commercially available stainless steel cleaning product The whistling is not a cause for concern Remedy Turn off the tap and contact the Service Force Centre Plug in mains plug Replace fuse If the dishes are to be washed immediately cancel the delay start Only wash cutlery dish es and pans that are suitable for dishwasher use Use a different brand of detergent If the Dishwashing Results are not Satisfactory The dishes are still dirty e The wrong dishwashing cycle was selected e The dishes were loaded is such a way that the dishwashing water did not reach all items The baskets for the dishes must not be overload ed e The filters in the base of the washing compartment are dirty or incor rectly positioned e Good quality detergent was not used or too little was used e In the case of scale deposits on the dishes The dishwasher salt dis penser is empty or the water softening system has been incorrectly set e The drain hose is incorrectly positioned The dishes do not dry and are not
11. put right an appliance which is improperly installed or calls to appli ances outside the United Kingdom e Appliances found to be in use within a commercial environment plus those which are subject to rental agreements e Products of AEG manufacture which are not marketed by AEG European Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications e The guarantee starts from the date you first purchased your product e The guarantee is for the same period and to the same extent for labour and parts as exists in the new country of use for this brand or range of products e This guarantee relates to you and cannot be transferred to another user e Your new home is within the European Community EC or European Free Trade Area e The product is installed and used in accordance with our instructions and is only used domesti cally i e a normal household e The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care centre listed below to give them de tails of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 3 44 62 29 29 Germany N rnberg 49 0 800 234 7378 Italy Pordenone 39 0 800 117511 Sweden Stockholm 46 0 8 672 5360 UK Slough 44 0 1753
12. ter system B 3 Take hold of the coarse and fine fil ters 1 2 by the handle and remove them from the micro filter 3 4 Clean all filters thoroughly under running water 5 Remove the flat filter 4 from the base of the washing compartment and clean both surfaces thoroughly 6 Re insert the flat filter 7 Place the coarse and fine filters in the micro filter and press together 8 Insert the filter system in place and lock it by turning the handle clock wise as far as it will go Ensure that the flat filter does not protrude above the base of the washing com partment Ax Under no circumstances may the 4 dishwasher be used without its filters 22 What to do if Remedying small malfunctions If while the appliance is operating indicators on the control panel flash or are lit up as described in the following table please consult this to find out how to remedy the fault After remedying the fault that is flashing in the first or second rhythm in the programme progress display press the button for the dishwashing cycle that had already started The cycle will continue If the fault is displayed again or if other faults are displayed please contact your local Service Force Centre and inform them of the fault display Malfunction The programme indicator for the selected dishwashing cy cle is flashing the indicator for the end of the dishwashing cycle
13. that is sensitive to temperature Dishes or cutlery with glued parts Pewter or copper items Lead crystal glass Steel items that rust Wooden boards platters Items made from synthetic ma terials are of limited suitability Only wash stoneware in the dishwasher if it is specifically marked by the manufacturer as being dishwasher safe Glazed patterns may fade if washed very fre quently in the dishwasher Silver and aluminium parts have a tendency to discolour during washing Food remains e g egg white egg yolk and mustard often cause discoloration and staining on silver Therefore always clean food residues from silver immedi ately if it is not to be washed straight after use Glass can become dull after a large number of washes e Before loading the dishes you should Remove the worst of the food residues Soak pans with burnt on food residues e When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load bowls cups glasses pans etc with the opening downwards so that water cannot collect in them Dishes and items of cutlery must not lie inside one another or cover one another To avoid damage to glasses they must not touch one another Don t put small items e g lids in the baskets for the dishes but in the cutlery basket so that they can t fall through the holes 13 Loading cutlery
14. A By 3NI amoh am gt CTT TT TIE Reset i ON OFF button The ON OFF button is used to turn the dishwasher on and off Programme buttons End of cycle indicator Programme progress display 3h mM is S es am h Gp INTENSIV 30 NORMAL ECO CARE 70 MIN 65 50 LT tit 3IN1 Goo gt L RESET 1 2 3 Set delay timer Function buttons Select Control 3 in1 function indicators The Programme buttons are used to select the desired dishwashing cy cle Function buttons In addition to the pre set dishwashing cycle the following functions can also be set using these buttons Function button 1 Set the water softener Function button 2 Activate deactivate rinse aid dispenser Function button 3 not programmed Programme progress display The current stage of the programme is always shown in the programme progress display The control indicators have the following meanings 3 1 Refill with dishwasher salt aD Refill with rinse aid 1 These control indicators are never illuminated while a dishwashing cycle is running Prior to Using for the First Time 1 Set the water softener 2 Fill up with dishwasher salt 3 Fill up with rinse aid il If you wish to use 3in1 detergent do the following First read the section Using 3in1 detergents Switch on
15. FAVORIT 40650 Dishwasher User information AN GJ G Dear Customer Please read this user information carefully and keep it to refer to later Please pass the user information on to any future owner of the appli ance The following symbols are used in the text Safety instructions Warning Information that affects your personal safety Important Information that prevents damage to the appliance Useful tips and hints Environmental information Your dishwasher is fitted with the new PULSE WASH dishwashing system With this dishwashing system the motor speed and spray pressure are varied during the dishwashing cycle to achieve better cleaning of the dishes It is for this reason that the noise level var ies during the dishwashing cycle Contents Operating Instructions 0 2 ceeee eee 4 Safe lyse cats ak ag Ale greening ale Pak Aree oa land ate eae Ae eee aa 4 Diagram of Appliance 0 0 ee 5 Control Panel ssiri gd heed beni ea eee 5 Prior to Using for the First Time 0 eee eee eee eee 7 Setting the Water Softener 0 ccc eect nee 7 Adding dishwasher Salt cee eee eee eee eee 9 Filling Up with Rinse Aid 0 0 eee eens 10 lid ally use seca siete ind ean aes Gt a eRe Tk Bead 13 Loading cutlery and dishes 00 cece eee eee 13 Adding Detergenti sirsa bidet eee eda wea eee eee 17 Usi
16. basket Installation and connection instructions A Safety Information for the Installation e Only transport the dishwasher in an upright position otherwise salt water may run out e Before using the dishwasher for the first time check for any damage caused in transport Do not under any circumstances connect an ap pliance that is damaged In the case of damage please contact your supplier e Never use the dishwasher if the mains cable water inlet or drain hose are damaged or if the control panel work top or plinth area are damaged such that the inside of the appliance is freely accessible e Always plug the mains plug into a correctly installed shockproof socket e Permanent connection a permanent connection must only be in stalled by a trained electrician e Prior to using the appliance for the first time ensure that the rated voltage and type of supply on the rating plate match that of the sup ply where the appliance is to be installed The fuse rating is also to be found on the rating plate e Multi way plugs connectors and extension cables must not be used This could constitute a fire hazard through overheating e The dishwasher s cable must only be replaced by a Service Force Engi neer e A water inlet hose with safety valve must only be replaced by a Serv ice Force Engineer 29 30 Installing the Dishwasher e
17. ces If you wish to hang the drain hose over the edge of a sink use a de tachable hose elbow You can obtain this from AEG Service Force by re ferring to spare part number ET 646 069 190 Fit the elbow to the drain hose Secure the drain hose so that it cannot slide off the edge of the sink Pass a piece of cord through the hose elbow and fix it to the wall or the tap Anti flood system For protection from water damage the dishwasher is equipped with a anti flood system In the event of a fault the safety valve in the water inlet hose immedi ately interrupts the supply of water to the appliance and the drain pump is activated In this way water can neither escape nor overflow The remaining water in the appliance is automatically pumped out Electrical Connection A Any electrical work required to install this appliance should be car ried out by a qualified electrician or competent person WARNING This appliance must be earthed The manufacturer declines any responsibility should these safety measures not be observed Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate To isolate the dishwasher from the mains remove the mains plug Important The plug must still be accessible after the appliance has been installed Changing a fuse The appliance is supplied with a 13amp plug fitted In the event of hav ing to change the fuse in the plug s
18. complete hose sets are to be used These are available from your local service centre Water drainage Drain hose Z The drain hose must not be kinked crushed or entangled Connecting the drain hose Maximum permitted height 1 metre Minimum required height 40 cm above the bottom edge of the ap pliance Extension hoses e Extension hoses are available from your local Service Force Centre To ensure that the function of the ap i AA pliance is not impeded the internal diameter of extension hoses must be 19 mm e Extension hoses must not be laid more than a maximum distance of 3 metres horizontally the maxi g mum permitted height for the con e nection for the drain hose is then a 3000m 85 cm gt 40 cm 85 cm Sink outlet connection e The outlet of the drain hose 19 mm fits all commonly available sink outlet types The outer diameter of the sink outlet connection must be at least 15 mm e The drain hose must be fixed to the sink outlet connection using the hose clamp supplied Water drainage if the dishwasher is built in at high level If the dishwasher is installed at a high level and the drain hose connec tion is less than 30 cm from the lower edge of the appliance adapter kit ET 111099520 must be fitted by your local Service Force Centre 33 34 N Water drainage into sink only possible with free standing appli an
19. e dish washer door Dishwasher Free standing appliances Dimensions 850 x 598 x 598 H x W x D in mm Max weight 54 kg C This appliance conforms with the following EU Directives 73 23 EEC dated 19 02 1973 Low Voltage Directive 89 336 EEC dated 03 05 1989 EMC Directive inclusive of Amending Directive 92 31 EEC 93 68 EEC dated 22 07 1993 CE Marking Directive 26 Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test cycle see Cycle Table Tests in accordance with EN 50242 must be carried out when the salt dispenser in the water softener and the rinse aid dispenser have been filled with salt and rinse aid respectively and using the test cycle see Cycle Table Full load 12 place settings including serving dishes Amount of detergent required 5g 25g Type B Rinse aid setting 4 Type III Sample loading arrangements Upper basket Half load 6 place settings including serving dishes leaving alter nate positions in the rack free 20g Type B 4 Type III F i LAT CHAAAR AAAF If necessary move the cup rack from right to left When doing this ensure that the cup rack is at the same height 27 Lower basket with cutlery basket Cutlery
20. essed The LED indicators for function buttons 1 to 3 will flash 3 Press function button 1 The LED indicator for function button 1 will flash The LED indicator for the end of the dishwashing cycle will flash simul taneously The number of times that the LED indicator for the end of the dish washing cycle flashes corresponds to the hardness setting This sequence of flashes is repeated several times with a 3 second pause in between 4 Pressing function button 1 increases the hardness setting by 1 degree Exception hardness setting 1 follows hardness setting 10 5 When the hardness setting is correct press the ON OFF button The hardness setting is now saved If the water softener is set electronically to 1 this switches off the control indicator for special salt Water hardness Adjusting the hardness setting Number of flashes in d in mmol l Range Manual Electronic 51 70 9 0 12 5 10 10 43 50 7 6 8 9 9 9 37 42 6 5 7 5 IV 1 8 8 29 36 5 1 6 4 7 7 23 28 4 0 5 0 6 6 19 22 3 3 3 9 HII 5 5 15 18 2 6 3 2 4 4 11 14 1 9 2 5 II 3 3 4 10 0 7 1 8 I 11 2 2 1 below 4 below 0 7 l no salt 1 necessary 1 d German degree measure of the hardness of water 2 mmol l millimol per litre international unit for water hardness 3 On this setting the length of the dishwashing cycle may be slightly longer factory setting Adding dishwasher Salt N NO Open the door and
21. is flashing in sequence 1 short light signal with approx 3 second pause in between Problems with water inlet The programme indicator for the selected dishwashing cy cle is flashing the indicator for the end of the dishwashing cycle is flashing in sequence 2 short light signals one after anoth er Possible cause The tap is blocked or furred with lime scale The tap is turned off The filter where present in the threaded hose fitting on the tap is blocked Filters in the base of the washing compartment are blocked Water inflow hose has not been correctly positioned The sink spigot connection is blocked Water drain hose has not been correctly positioned Remedy Clean tap Turn the tap on Clean the filter in the threaded hose fitting Press the button for the dishwashing cycle that has started then cancel the dish washing cycle see sec tion Starting a dishwashing cycle clean filters see section Cleaning the filters Check hose installation Clean the sink spigot outlet Check hose installation 23 24 Malfunction the indicator for the end of the dishwashing cycle is flashing in sequence 3 short light signals one after anoth er The cycle is not starting Rust spots are visible in the dishwashing compartment A whistling noise can be heard when washing dishes Possible cause The anti flood system has been triggered The mains plug
22. ng 3in1 detergents 0 cece eee eee eens 18 Selecting the dishwashing cycle Cycle Table 0 cee eee 19 Starting a Dishwashing Cycle 00 e eects 20 Setting the Delay Timer 6 0 0 ccc eet 20 Switching Off the dishwasher 00 c cece eee eee eens 21 Care and cleaning eee eee eee a 22 What to do ifii saci hase teria See Sea ie ce ed 23 Remedying small malfunctions 0 eee eee ee 23 If the Dishwashing Results are not Satisfactory 2 05 24 DispoSall iiss rosie rann a a a deny Culpa a ats 25 Technical Data oyicsc es virgen araor Tea a 26 Notes for Test Institutes 0 eee 27 Installation and connection instructions 29 Safety Information for the Installation 29 Installing the Dishwasher 0 0 0 e eee eee 30 Connecting the dishwasher 0 00 cece eee eens 32 Electrical Connection 0 c cece eee eee es 35 Warranty conditions 00cce cece eee eee 37 Service and Spare Parts 0 0 anaana 39 Operating Instructions A Safety Prior to using for the first time e Follow the Instructions for installation and connection Correct Use e The dishwasher is only intended for washing domestic dishes e Additions or modifications to the dishwasher are not permitted e Use only special salt detergent and rinse aid suitable for dome
23. not use 3in1 detergent fill up with rinse aid Before using the dishwasher for the first time When the control indicator for rinse aid is illuminated on the control panel Use only special rinse aid for dish washers 1 Open the door The rinse aid compartment is locat 4 ed on the inside of the dishwasher door l G 2 Press the release button on the rinse aid compartment AN 3 Open the cover 4 Pour rinse aid in slowly right up to the broken max line this corresponds to a volume of ap prox 140 ml when full 5 Press the lid shut until it clicks into place 6 Wipe up any spilt rinse aid with a cloth Otherwise there will be too much foam when rinsing Setting the Amount of Rinse Aid Required liJ Only change the amount dispensed if smears milky spots reduce the amount or dried on water spots increase the amount can be seen on glasses and dishes See section If dishwashing results are not satisfac tory The dosage can be set from 1 6 The dosage is pre set to 4 in the factory 1 Open the dishwasher door 2 Press the release button on the rinse aid compartment 3 Open the cover 4 Set the dosage level 5 Press the lid shut until it clicks into place 6 If rinse aid has leaked out wipe it away with a cloth Activating Deactivating the Rinse Aid dispenser 1 Press the ON OFF button If indicators for the programme butto
24. ns are lit a dishwashing cycle is activated The cycle must be deactivated Press function buttons 2 and 3 simultaneously for approx 2 seconds All additional wash programme button indicators will go out 2 Press function buttons 2 and 3 simultaneously and keep them pressed The LED indicators for function buttons 1 to 3 will flash 3 Press function button 2 The LED indicator for function button 2 will flash The indicator for the end of the dishwashing cycle will display the cur rent setting Rinse aid dispenser activated Indicator for the end of the cycle is lit factory setting Indicator for the end of the cycle is not lit Rinse aid dispenser deactivated 4 Pressing function button 2 activates and deactivates the rinse aid dis pensing function 5 When the rinse aid dispenser setting is correct press the ON OFF but ton The setting for the rinse aid dispenser is now saved In daily use Loading cutlery and dishes AN Sponges cleaning cloths and any other objects that can absorb water must not be washed in the dishwasher Plastic and Teflon coated dishes and pans tend to retain water droplets These dishes and pans therefore do not dry as well as those made of china and stainless steel For washing in the dishwasher the following cutlery dishes pots and pans are not suitable Cutlery with wooden horn china or mother of pearl han dles Plastic items that are not heat resistant Older cutlery with cement
25. re Ltd Berkshire SL1 1DZ Long Mile Road Dublin 12 Tel 08705 350350 Republic of Ireland Tel 353 0 1 4090751 Email service eid electrolux ie Calls may be recorded for training purposes 39 a From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year to a value of approx USD 14 billion in more than 150 countries around the world AEG Hausger te GmbH Postfach 1036 D 90327 Nurnberg http www aeg hausgeraete de Copyright by AEG 822 961 160 00 190504 03 Subject to change without notice
26. remove the low Unscrew the lid on the salt dispens Only when using the dishwasher Place the funnel supplied over the To decalcify the water softener it must be filled up with dishwasher salt Use only special salt suitable for domestic dishwashers If you do not use 3 in1 detergent fill up with dishwasher salt Before using the dishwasher for the first time When the control indicator for dishwasher salt is illuminated on the control panel er basket er by turning it anti clockwise for the first time Fill the salt dispenser with water dispenser opening Fill the dispenser with dishwasher salt the capacity of the dispenser is approx 1 0 1 5 kg depending on the size of the grains Do not overfill the dispenser If water overflows when filling up with dishwasher salt this is com pletely harmless Clean away any salt remnants from the dispenser opening Screw the lid back on in a clockwise direction Run a dishwashing cycle after filling the salt dispenser with dish washer salt This will wash away salt water and salt crystals that have been spilt Depending on the size of the salt granules it can take several hours for the salt to dissolve in the water and for the control indicator for dish washer salt to go out Filling Up with Rinse Aid Rinse aid causes the rinse water to flow easily from the crockery leav ing gleaming dishes and glassware If you do
27. shining e Poor quality rinse aid was used e The rinse aid dispenser is empty There are smears streaks milky spots or a shiny bluish coating on glasses and dishes e Lower rinse aid dosage There are dried water drops on the glasses and dishes e Increase rinse aid dosage e The detergent may be the cause Contact the detergent manufactur er s customer advice centre Glass corrosion e Contact the detergent manufacturer s customer advice centre Disposal Gy o AN Packaging material The packaging materials are environmentally friendly and can be recy cled The plastic components are identified by markings e g gt PE lt gt PS lt etc Please dispose of the packaging materials in the appropriate container at your local waste disposal facilities Old appliance Please dispose of your old appliance in line with the guidelines for dis posal in your area Warning When your appliance has finished its working life remove the plug from the socket Cut off the cable and plug and dispose of them Break the door lock so that the door no longer shuts This prevents chil dren from trapping themselves inside and endangering their lives 25 Technical Data Capacity 12 place settings including serving dishes Permitted water pres 1 10 bar 10 100 N cm 0 1 1 0 MPa sure Information on the electrical connection is given on the Electrical connection rating plate located on the right inner edge of th
28. stic dishwashers e Do not put any solvents in the dishwasher This could cause an explo sion Child Safety Keep packaging away from children There is a risk of suffocation e Children often do not recognise the hazards associated with electrical appliances Don t allow children to use the dishwasher unsupervised e Make sure that children and pets don t climb into the dishwasher Could endanger life e Dishwasher detergents can cause chemical burns to the eyes mouth and throat Could endanger life Comply with the safety instructions of the dishwasher detergent manufacturer e The water in the dishwater is not for drinking Risk of chemical burns General Safety Repairs to the dishwasher are only to be carried out by qualified au thorised service engineers e When the dishwasher is not being used switch it off and shut off the water tap e Never unplug the appliance by pulling on the cable Always pull the plug e Never sit or stand on the open door e f the dishwasher is located in a room where there may be a frost re move the connection hose from the tap after each use of the dish washer Diagram of Appliance Top Spray Nozzle Upper basket spray arm and lower spray arm Water softener unit Salt Container Detergent Dispenser an Rinse aid dispenser Rating plate Filters Control Panel INTENSIV 30 NORMAL ECO DEI MIN
29. the dishwasher press 3in1 button The button indicator lights up 3in1 function is selected As a result there is no need to fill up with dishwasher salt or rinse aid there is no need to set the water softener there is no need to activate deactivate the rinse aid dispenser Before the start of the dishwashing cycle put 3in1 detergent in the detergent dispenser Setting the Water Softener The water softener must be set manually and electronically il To avoid scale deposits on the dishes and in the dishwasher the dishes must be washed with soft water i e water with a low lime content The water softener must be set according to the table to the water hard ness in the area where you live Your local water company will be able to give you information about the water hardness in your area The dishwasher must be switched off Setting manually Open the dishwasher door Remove the lower basket from the dishwasher 3 Turn water hardness dial on the left wall of the dishwasher interior to O or 1 see table N Setting electronically Press the ON OFF button il If indicators for the programme buttons are lit a dishwashing cycle is activated The cycle must be deactivated Press function buttons 2 and 3 simultaneously for approx 2 seconds All additional wash programme button indicators will go out 2 Press function buttons 2 and 3 simultaneously and keep them pr
30. ults that can otherwise only be achieved using 65 C cycles Detergent tablets Detergent tablets from different manufacturers dissolve at different rates For this reason some detergent tablets do not attain their full cleaning power during short cycles Therefore please use dishwashing cycles with pre wash when using detergent tablets Using 3in1 detergents These products are detergents with a combined cleaning rinsing and salt function 1 Check whether these detergents are suitable for your water hardness Follow the manufacturer s instructions 2 Place detergent just in the detergent dispenser If you want to stop using 3in1 products please do the following e Fill up the dispensers for salt and rinse aid again e Switch the water softener to the highest setting and perform up to three normal cycles without loading any dishes e Then set the water softener to the water hardness in your area Selecting the dishwashing cycle Cycle Table Programme se Consump quence tion values Vv Dishwashing Suitable Type of T cae y cycle for soiling v alala 2 amp z x ie vN 5 n Ww x 0 a SSS p aS 8 gt Sle EE Ss 4 2 za as es ea Pe jee eee cs ee Sie lis S on S heavily soiled S B aa 2 se InTENSIv Dinner Sev ried_on food re foetal es 2 ice and Tae om ei 2 xq om ine 1 CARE 70 mains in particular alela cookware A Oo N protein and starch S 30 MIN aes
31. upplied a 13amp ASTA approved BS 1363A fuse must be used Should the plug need to be replaced Green amp Yellow for any reason proceed as described below The wires on the mains lead are col oured in accordance with the fol lowing code Green and Yellow Earth Blue Neutral Brown Live Cord Clamp e The wire coloured green and yellow must be connected to the termi nal marked with the letter E or by the earth symbol or coloured green and yellow e The wire coloured blue must be connected to the terminal N or col oured black e The wire coloured brown must be connected to the terminal marked L or coloured red e Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath WARNING A cut off plug inserted into a 13 amp socket is a seri ous safety shock hazard Ensure that if it is necessary to cut off the plug it is disposed of safely and not retained 35 36 Connecting systems The water inlet hose drain hose and the mains cable must all be con nected to the side of the dishwasher as there is no space for them be hind the appliance 2 connection pieces 45 orm doublevalve water waterinlet straight outer 19 mm drainage length 30 mm ra i A f J vi fos ge EREEEES Ji sosy
Download Pdf Manuals
Related Search