Electrolux FAVORIT 40310 User's Manual
Contents
1. GUARANTEE CONDITIONS Guarantee Conditions AEG offer the following guarantee to the first purchaser of this appliance 1 The guarantee is valid for 12 months commencing when the appliance is handed over to the first retail purchaser which must be verified by purchase invoice or similar doc umentation The guarantee does not cover commercial use 2 The guarantee covers all parts or components which fail due to faulty workmanship or faulty materials The guarantee does not cover appliances where defects or poor per formance are due to misuse accidental damage neglect faulty installation unauthorised modification or attempted repair commercial use or failure to observe requirements and recommendations set out in the instruction book This guarantee does not cover such parts as light bulbs removable glassware or plastic dust bags or filters 3 Should guarantee repairs be necessary the purchaser must inform the nearest customer service office manufacturer s service or authorised agent AEG reserves the right to stipulate the place of the repair i e the customer s home place of installation or AEG workshop 4 The guarantee or free replacement includes both labour and materials 5 Repairs carried out under guarantee do not extend the guarantee period for the appli ance Parts removed during guarantee repairs become the property of AEG 6 The purchaser s statutory rights are not affected by this guarantee European2. This appliance conforms with the following EU Directives 73 23 EWG dated 19 02 1973 Low Voltage Directive 89 336 EWG dated 03 05 1989 including Directive Amendment 92 31 EWG EMC Directive Operating Instructions Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test programme see Programme Table Tests in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme see Programme Table Detergent Dosing Rinse Aid Setting Full Load 12 place settings incl serving dishes 5g 25g Type B 4 Type III Sample loading arrangements Upper basket FH Lj H LEHA Half Load 6 place settings incl serving leaving alternate positions free 20g Type B 4 Type III Yu 9 aS b PR IM r1 iban SPI NERA jajajaja m WS Li 29 Installation and Connection Instructions 30 INSTALLATION AND CONNECTION INSTRUCTIONS Installing the Dishwasher e The dishwasher must be installed on a firm floor and adjusted such that it is stable and level o compensate for unevenness in the floor and t
3. 0 00 cece eects 25 What fo d if 5 04 err OH Be aed 26 there are problems with the operation of the dishwasher 26 the wash result is unsatisfactory llseseelesseseeesresen 27 Technical Data soii terai en hae EA Seve eed aed Seva 28 Notes for Test Institutes usus eee eee eee 29 Contents Installation and Connection Instructions 30 Installing the Dishwasher seeeeeee BR 30 Built Under Dishwasher en RR RR 30 Free Standing Appliances 0 ccc cece eee eee rere 30 Connecting the Dishwasher 0 c eee e eee eee 32 Water Connection lile eee eee II e 32 Permitted water pressure sslssssesesee ees 32 Connect the inlet hose llssssssesee RR 32 Mater dralle secs cione cede Ule so a ee usa d e lds nde doe ee dol it ted 34 Leak Prevention System ssssssssssssssse ess 35 Electrical Connection seunes 0 cece eee RII 36 Connections ura doe au eoe ea See ae Oe EN To A wi pan eee Ad i ae ans 37 Guarantee Conditions 38 Service and Spare parts uuuututuuuuusuueun 39 Operating Instructions OPERATING INSTRUCTIONS Safety Instructions The safety aspects of AEG electrical appliances comply with accepted technical standards and the German Appliance Safety Law Neverthe less as a manufacturer we consider it our obligation to make you aware o
4. Installation and Connection Instructions 32 Connecting the Dishwasher Water Connection am The dishwasher is fitted with safety devices that prevent the wash water returning into the drinking water system and comply with the applicable plumbing regulations e The dishwasher must be connected to a cold water supply e The dishwasher must not be connected to open hot water appliances or instantaneous water heaters Permitted water pressure Lowest permitted water pressure Consult your installer if the water pres 1 bar 210 N cm 100 kPa sure is less than 1 bar Highest permitted water pressure In the case of a water pressure greater 10 bar 2100 N cm 1 MPa than 10 bar a pressure reduction valve must be used available from your dealer Connect the inlet hose The water inlet hose must not be kinked crushed or entangled when it is being connected up Connect the threaded hose fitting ISO 228 1 2000 on the water inlet hose to a tap with an external thread 34 inch Tighten the threaded hose fitting hand tight only n order that access to the tap in the kitchen is not limited by the use of the dishwasher we recommend the installation of an additional tap or fitting a two way adapter to the existing tap e f you need a longer water inlet hose than that supplied VDE approved complete hose sets are to be used These are available from your local Service Force Centre Do not use for connecti
5. Maximum permitted height 1 metre Minimum required height 40 cm above the lower edge of the machine Extension hoses e Extension hoses are available from AEG Service Force The internal diameter of the extension hoses must be 19 mm to ensure that the function of the appliance is not impeded Hoses may be laid a maximum of 3 metres horizontally the maximum P permitted height for the connection z DEG for the drain hose is then 85 cm 300 cm Sink outlet connection 85 cm gt 40 cm e The outlet of the drain hose 19 mm fits all commonly available sink outlet spigot types The outer diameter of the spigot connection must be at least 15 mm e The drain hose must be fixed to the sink outlet connection using the hose clamp supplied If the dishwasher is fitted at a high position If the dishwasher is installed at a high level and the drainhose connec tion is less than 30 cm from the bottom of the appliance adapter kit ET 111099520 must be fitted This is available from Customer Service Discharging into a standpipe When discharging into a standpipe the upright standpipe should have a minimum length of 30 cm 12 from the bottom of the elbow to the top of the pipe see diagram Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water Min 38mm 12 diameter standpipe Min 30 cm 12 Installation and Connection Instru
6. described below The wires on the mains lead are coloured in accordance with the following code Green and Yellow Earth Blue Neutral Brown Live The wire coloured green and yellow must be connected to the termi nal marked with the letter E or by the earth symbol or coloured green and yellow The wire coloured blue must be connected to the terminal N or col oured black e The wire coloured brown must be connected to the terminal marked L or coloured red Upon completion there must be no cut or stray strands of wire present and the cord clamp must be secure over the outer sheath WARNING A cut off plug inserted into a 13 amp socket is a seri ous safety shock hazard Ensure that if it is necessary to cut off the plug it is disposed of safely and not retained Installation and Connection Instructions Connections The water inlet and drain hoses as well as the mains cable must be connected beside the dishwasher as there is insufficient space behind the appliance The plumbing and electrical installation example given below can only be regarded as a recommendation Two 45 or Straight Connections Outer 19 mm Length 30 mm Double tap Water drain Water inlet Water Mains Water Mains socket Mains inlet cable drain cable 37 Guarantee Conditions
7. Guarantee If you should move to another country within Europe then your guarantee moves with you to your new home subject to the following qualifications The guarantee starts from the date you first purchased your product The guarantee is for the same period and to the same extent for labour and parts as exist in the new country of use for this brand or range of products This guarantee relates to you and connot be transferred to another user Your new home is within the European Community EC or European Free Trade Area The product is installed and used in accordance with our instructions and is only used domestically i e a normal household The product is installed taking into account regulations in your new country Before you move please contact your nearest Customer Care Centre listed below to give them details of your new home They will then ensure that the local Service Organisation is aware of your move and able to look after you and your appliances France Senlis 33 0 44 62 29 29 Germany N rnberg 49 0 800 234 7378 Italy Pordenone 39 0 800 117511 Sweden Stockholm 46 0 8 672 5360 UK Slough 44 0 1753 219899 Service and Spare parts SERVICE AND SPARE PARTS In the event of your appliance requiring service or if you wish to pur chase spare parts please contact Service Force by telephoning 08705 929 929 Your telephone call will be automatically routed to the Service Force Centre cov
8. needs repairing please contact your local AEG Service Force Centre Operating Instructions Never place the dishwasher in operation if the mains cable water inlet or drain hose is damaged or the control panel work top or plinth area is damaged such that the inside of the appliance is freely accessible e f the mains lead is damaged or is to be replaced for a longer lead the cable obtainable from AEG Service Force must be replaced by a service engineer authorised by AEG Never unplug the appliance by pulling on the cable always pull the plug Additions or modifications to the dishwasher are not permitted for safety reasons Ensure that the door of the dishwasher is always closed when it is not being loaded or unloaded In this way you will avoid anybody tripping over the open door and hurting themselves Long bladed knives stored in an upright position are a potential haz ard Long and or sharp items of cutlery such as carving knives must be positioned horizontally in the upper basket e When finished loading or unloading close the door as an open door can be a hazard Correct Use Only wash household dishes using the dishwasher If the appliance is used for other purposes or is used incorrectly the manufacturer can not accept any liability for any damage caused Only use detergents specifically designed for use in domestic dish washers Do not put any solvents in the dishwasher Th
9. FAVORIT 40310 Dishwasher User Instructions AN p i D Dear customer Please read these user instructions carefully Please observe the safety instructions on the first few pages ofthese user instructions Please keep these user instructions for later reference Pass them on to any subsequent owner of the appliance The warning triangle and or specific words Warning Caution Important are used to highlight instructions that are important for your safety or for the function of the appliance It is imperative that these instructions are observed This symbol or numbered instruction steps lead you step by step through the operation of the appliance Next to this symbol you receive additional information and practical tips on using the appliance Tips and instructions for the economical and environmentally conscious use of the appliance are marked with a clover leaf In the event of a malfunction these operating instructions contain information on how to rectify faults yourself see the What to do if section If these instructions are insufficient please contact your AEG Service Force Centre In this respect please read the chapter Service amp Spare Parts Printed on paper manufactured with environmentally sound processes He who thinks ecologically acts accordingly Contents CONTENTS Operating Instructions ssueueeeeeeeeeeeesee 5
10. Safety Instructions ieii ea ea a a eens 5 Disposal cas ir a A a Ua a AT E E 7 Economical and Ecological Dishwashing sssse 7 Appliance Features and Control Panel 8 Control Panel i i ec EUER EUR Gea eed chad 9 Prior to using for the first time 0 0 eee eee eee 9 Adjust the Water Softener eee eee eres 10 Filling with Salt for the Water Softener 000000 eee eee 11 Filling with Rinse Aid 0 00 cece eect eee 12 Adjusting Rinse Aid Dosing 000 cece eee eee ens 13 In Daily Use rs mte yh e es 14 Loading Cutlery and Dishes eee cece eects 14 Loading Cutlery sse neds Re lsonhie feeds e pw es 15 Loading Pans Frying Pans and Large Plates 16 Loading Cups Glasses and Coffee Services 22000000000s 18 Filling with Detergent scu rassi iai pirri eee 19 Use of 3 in 1 Combi Detergent Tablets 0 cece eae 20 Concentrated Detergent ee cece eects 21 Deterg ent tablets mersit ipeto We er e ERR el GS 21 Selecting the Wash Programme Programme Table 22 Starting the Wash Programme 0 000 cece eee eee eens 23 Changing Interrupting the Wash Programme 000005 23 Switching Off the Dishwasher 000000 eect eee eee eee 24 Emptying the Dishwasher 020 c cece e eee ees 24 Care and Cleaning cece cece 24 Cleaning the Filter
11. alt This will wash away salt water and any salt crystals that have been spilt Depending on the size of the salt grains it can take several hours for the salt to dissolve in the water and the special salt indicator G to extinguish The setting of the water softener and the consumption of salt are dependent on the hardness of the local water 11 Operating Instructions Filling with Rinse Aid AN Open the door Press the rinse aid compartment Fully open the rinse aid compartment lid x Gv C SIL Fill with rinse aid exactly up to the Close the lid and press until it locks Wipe up any spilt rinse aid with a Rinse aid is automatically added during the last rinse ensuring thor ough rinsing spot and streak free drying Only use rinse aid specifically designed for domestic dishwashers Never fill the rinse aid container with any other substance as this would dam age the appliance Fill with rinse aid Prior to using the dishwasher for the first time When the window indicator has a dark centre surrounded by a light ring If there is rinse aid in the container the indicator window is completely dark The rinse aid compartment is on the inside of the dishwasher door release button with your finger alles level marked max this corresponds to a quantity of approx 140 ml into place cloth Otherwise too much foam will be formed during the wash Ope
12. ance is in guarantee there are problems with the operation of the dish washer Symptom The drain pump in the dishwasher runs con tinuously even with the appliance switched off The programme does not start Rust spots are visible in the washing compart ment There is a whistling noise during washing Possible Cause The anti flood system has been triggered The door of the dishwasher is not closed properly Mains plug is not plugged in House fuse in defective A delay start is selected The washing compartment is made of corrosion resistant stainless steel Rust spots in the washing compartment are from particles from out side the appliance rust par ticles from the water pipe from pans cutlery etc Remove such spots with a commercially available stain less steel cleaner The whistling is not a cause for concern Solution Close the tap then unplug from the mains and contact AEG Service Force Shut the door Insert mains plug Replace fuse If the dishes are to be washed immediately set the delay start to 0 hours Only wash cutlery and dishes that are suitable for dish washer use Close the lid of the special salt container securely Use a different brand of detergent Operating Instructions the wash result is unsatisfactory The dishes are still dirty The wrong wash programme was selected he dishes were arranged in such a manner that wa
13. ating Instructions Open the door remove the lower The dishwasher filter system com Turn the handle about 1 4 a turn anti Take hold of the coarse fine filter 1 Clean all filters thoroughly under Remove the flat filter 3 from the Put the flat filter back in the base of Place the coarse fine filter in the Put the filter combination in place Cleaning the Filter The filters should be checked and cleaned regularly Blocked filters will give poor wash results rack prises a coarse fine filter microfilter and a flat filter Unlock the filter sys tem using the handle on the microfil ter and remove clockwise and remove by the handle with the hole and remove from the microfilter 2 running water base of the washing compartment and clean both faces thoroughly the washing compartment microfilter and press together and lock by turning the handle clock wise to the stop During this process ensure that the flat filter does not protrude above the base of the wash ing compartment The dishwasher must not be used without filters under any circum stances 25 Operating Instructions 26 What to do if Try to rectify minor faults on the dishwasher with the aid of the instructions given here If you call an engineer to resolve a of fault listed here or to repair a fault caused by incorrect use or installation a charge will be made even if the appli
14. ch the dish racks are secured for transport Then perform the following steps ts 1 Adjust the water softener 2 Fill with Salt for the Water Softener 3 Fill with Rinse Aid Operating Instructions Adjust the Water Softener i ts Adjust the water softener in accord To prevent the build up of scale on dishes and in the dishwasher the dishes must be washed with soft i e low lime content water For this reason the dishwasher is fitted with a water softener in which tap water from a hardness of 4 d German degrees is softened with the aid of special salt Your local water authority can advise you on the hardness of the water in your area The water softener has 4 settings Water Hardness Turn the arrow on the in d in ppm 2 water hardness switch to number 36 50 640 900 4 22 35 390 630 3 15 21 260 380 Da 4 14 70 250 1 1 under 4 under 70 no salt necessary 1 d German degree measure of water hardness 2 ppm Parts Per Million CaCO factory setting ance with the table to suit your area 1 Open the door on the dishwasher 2 Remove the lower rack from the dishwasher 3 Turn the water hardness switch to 1 2 3 or 4 4 Replace the lower rack and close the door of the dishwasher Operating Instructions Filling with Salt for the Water Softener AN Open the door remove the lower Undo the lid on the salt container by When using for the f
15. ctions AN Leak Prevention System For protection from damage due to water leaks the dishwasher is equipped with a leak prevention system the AQUA CONTROL SYSTEM In the event of a fault the safety valve in the appliance immediately interrupts the inflow of water and the drain pump is activated By this means water can neither escape nor overflow The remaining water in the appliance is automatically pumped out The leak prevention system also works when the appliance is switched off the appliance must however not be disconnected from the mains 35 Installation and Connection Instructions 36 Electrical Connection AN Any electrical work required to install this appliance should be car ried out by a qualified electrician or competent person WARNING This appliance must be earthed The manufacturer declines any responsibility should these safety measures not be observed Before switching on make sure the electricity supply voltage is the same as that indicated on the appliance rating plate To isolate the dishwasher from the mains remove the mains plug Important The plug must still be accessible after the appliance has been installed Changing a fuse The appliance is supplied with a 13amp plug fitted In the event of hav ing to change the fuse in the plug supplied a 13amp ASTA approved BS 1363A fuse must be used Should the plug need to be Green replaced for any reason proceed as amp Yellow
16. cutlery are loaded into the dishwasher the spray arms are free to rotate Open the tap fully 3 Turn the programme switch clockwise to A or B or C see Programme Close dishwasher door Table For interference suppression reasons only operate the programme selector with the dishwasher switched off It is also possible that the automated addition of detergent will be triggered Turn the programme selector to the required programme see Pro gramme Table Power indicator light illuminates The selected wash programme starts The programme selector rotates during the wash programme and indi cates the position that has been reached in the programme If a wash programme has been started even though the tap was closed turn the programme selector to the position open the tap and start the programme again Changing Interrupting the Wash Programme Only change or interrupt a wash programme in progress if it is abso lutely necessary Changing the wash programme Turn the programme selector to the position Power indicator light goes out wash programme stops Hot steam may escape when the door is opened Open the door care fully Open dishwasher door and check whether there is still detergent in the container Refill the container if necessary Close dishwasher door Turn the programme switch clockwise to A or B or C see Programme Table Turn the programme selector to the required
17. ease button 1 The lid springs open Fill the detergent dispenser with detergent The markings indicate the dosing levels 20 corresponds to approx 20 ml of detergent 30 corresponds to approx 30 ml of detergent Close the lid and press until it locks into place If the dishes are very heavily soiled put additional detergent into the adjacent chamber 2 This detergent will take effect during the pre wash Gm D W 19 Operating Instructions is 1 20 Use of 3 in 1 Combi Detergent Tablets General Advice These products are tablets with combined detergent rinse aid and salt functions Before using these products you should first check that the water hard ness in your supply is compatible with the use of these products as per the detergent manufacturers instructions on the product packaging These products should be strictly used according to the detergent manufacturers instructions Do not place the tablets in the tub or the cutlery basket as this will result in poorer wash results The tablets should be placed in the detergent doser If you encounter problems when using 3 in1 products for the first time then please contact the detergent manufacturers care line the telephone number is given on the product packaging Special Advice When using combination products the rinse aid and salt lights are no longer useful It may be h
18. elpful therefore to switch the rinse aid off please note that only some dishwashers have this facility and selec ting the lowest possible setting for water hardness For more information please refer to your instruction manual If you decide to switch to the use of a standard detergent system we advise that you e Refill both the salt and rinse aid compartments Switch the waterhardness setting to the highest possible position and run for three normal cycles without a load Readjust the waterhardness setting again according to the conditions for your region as per the instruction manual Operating Instructions Concentrated Detergent Based on their chemical composition dishwasher detergents can be split into two basic types conventional alkaline detergents with caustic components low alkaline concentrated detergents with natural enzymes The use of 50 C wash programmes in conjunction with concentrated detergents reduces pollution and is good for your dishes these wash programmes are specially matched to the dirt dissolving properties of the enzymes in the concentrated detergent For this reason 50 C wash programmes in which concentrated detergents are used can achieve the same results that can otherwise only be achieved using 65 C pro grammes Detergent tablets Detergent tablets of different makes dissolve at different speeds For this reason some detergent tablets cannot develop their full cleaning po
19. ere is a risk of an explo sion e The anti flood system provides dependable protection against dam age due to leaks For this system to function correctly the following preconditions must be met he appliance must remain connected to the mains even when it is switched off The dishwasher must be correctly installed Always shut off the water supply at the tap when the dishwasher is not to be used for longer periods e g when you are away on holiday Do not sit or stand on the open door the appliance may tip over Operating Instructions e n the event of a fault first close the tap then switch off the appli ance and unplug it from the mains If the appliance is permanently wired to the mains remove the fuse Disposal Disposing of the Packaging Material Dispose of the dishwasher packaging material correctly All the packag ing materials used are harmless to the environment and can be recy cled Plastic parts are marked with standard international abbreviations PE for polyethylene e g sheet wrapping material PS for polystyrene e g padding material always CFC free POM for polyoxymethylene e g plastic clips e Cardboard packaging is manufactured from recycled paper and should be deposited in the waste paper collection for recycling Disposal of Old Appliances When disposing of old appliances remove the plug and ensure that any locks or catches are removed to prevent young c
20. ering your post code area For the adress of your local Service Force Centre and further informa tion about Service Force please visit the website at www serviceforce co uk Before calling out an engineer please ensure you have read the details under the heading What to do if When you contact the Service Force Centre you will need to give the following details 1 Your name address and post code 2 Your telephone number 3 Clear and concise details of the fault 4 The model and serial number of the appliance found on the rat ing plate 5 The purchase date Please note that a valid purchase receipt or guarantee documentation is required for in guarantee service calls Customer Care For general enquiries concerning your AEG appliance or for further information on AEG products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www aeg co uk Customer Care Department AEG Domestic Appliances 55 77 High Street Slough Berkshire SL1 1DZ Tel 08705 350350 Calls may be recorded for training purposes m e From the Electrolux Group The world s No 1 choice The Electrolux Group is the world s largest producer of powered appliances for kitchen cleaning and outdoor use More than 55 million Electrolux Group products such as refrigerators cookers washing machines vacuum cleaners chain saws and lawn mowers are sold each year t
21. f limited suitability Only wash stoneware in the dishwasher if it is specifically marked as being dishwasher safe by the manufacturer Glazed patterns may fade if machine washed frequently Silver and aluminium parts have a tendency to discolour during washing Left overs e g egg white egg yolk and mustard often cause discolouring and staining on silver Therefore always clean left overs from silver immediately if it is not to be washed straight after use Some types of glass can become dull after a large number of washes Before loading the dishes you should Remove all scraps of food Soften remnants of burnt food in pans When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc with the opening downwards so that water cannot collect in the container or a deep base Dishes and items of cutlery must not lie inside one another or cover each other Operating Instructions gt B To avoid damage to glasses they must not touch Do not lay small objects e g lids in the cutlery rack Loading Cutlery Long bladed knives stored in an upright position are a potential haz ard Long and or sharp items of cutlery such as carving knives must be posi tioned horizontally in the upper bas ket Take care when loading or unloading sharp items such as knives To ensure that al
22. f the following safety information Installation Connection and Placing into Operation e The dishwasher may only be transported upright e Check the dishwasher for transport damage Do not in any circum stances connect an appliance that is damaged In the case of damage please contact your retailer Before installing the appliance ensure that the nominal voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed The fuse rating is also to be found on the rating plate For information on how to correctly install and connect up your dish washer please read the Installation section Adaptors connectors and extension cables must not be used Child Safety his appliance is designed to be operated by adults Children should not be allowed to tamper with the controls or play with the product Keep all packaging away from children e Keep all detergents in a safe place out of children s reach The water in your dishwasher is not suitable for drinking If there are still remnants of detergent in the appliance there is a risk of burns When disposing of an old appliance cut off the power supply cable and remove any door catches to prevent young children being trapped inside General Safety Repairs to the dishwasher are only to be carried out by qualified serv ice engineers Improper repairs can give rise to significant hazards for the user If your appliance
23. hildren becoming trapped inside Use an authorised disposal site Economical and Ecological Dishwashing Ensure that the water softener is correctly adjusted Do not pre rinse dishes under running water e Select the wash programme to suit the nature and degree of the soil ing on the dishes Do not use more detergent special salt or rinse aid than is recom mended in these operating instructions and by the detergent manu facturer Operating Instructions Appliance Features and Control Panel Rubber Seal for Connecting the Water Feed to the Upper Spray Arm Spray Arms Water Hardness Switch i gt E a Container for Salt Container for Rinse Aid Detergent Rating Plate Filters Operating Instructions Control Panel Power Indicator Light SALT Indicator o QUICK 50 NORMAL 50 EJ pe A 1 NORMAL 65 ECO 50 A B Programme Selector Door Handle Programme Switch Set the point at which the wash programme is to start using the pro gramme switch The programme switch rotates during the wash pro gramme and indicates the position that has been reached in the programme Switch on the dishwasher and start a wash programme using the pro gramme selector Prior to using for the first time Prior to using for the first time remove all the clips with whi
24. irst time Place the funnel supplied on the con Use only salt designed for dishwashers Never fill the salt container with any another type of salt e g culinary salt or dishwasher deter gent as this would irreparably damage the water softener Prior to filling with salt please check each time that you really do have a packet of dishwasher salt in your hand Fill with dishwasher salt Prior to using the dishwasher for the first time When the SALT indicator S on the control panel is illuminated If the water hardness in your area is less than 4 d you do not need to use dishwasher salt The SALT indicator S on the control panel will remain illuminated rack turning it anticlockwise fill the salt container with water tainer opening Fill the container with salt through the funnel the capacity of the con tainer is approx 1 0 1 5 kg depend ing on the grain size Do not overfill the salt container with salt The water expelled by filling the salt container with salt runs out of the salt container onto the base of the washing compartment This is not a cause for concern the water will be pumped out at the start of the next wash programme Clean any salt remnants on the container opening Turn the lid clockwise to the stop otherwise dishwasher salt will leak into the wash water this could lead to poor wash results To avoid this run a rinse programme after filling the salt container with special s
25. l items of cutlery are completely washed you should Place the grid insert on the cutlery rack Place short knives forks and spoons in the grid insert with their handles pointing downwards D E 15 Operating Instructions i Loading Pans Frying Pans and Large Plates Load large and heavily soiled dishes in the lower basket Your dishwasher has one of the following four types of lower basket Type 1 None of the plate inserts in the lower basket can be removed Type 2 The right hand plate inserts in the lower basket can be folded over to the left To ease the loading of large items the two right hand plate inserts in Ta u the lower basket can be folded over 1 to the left 1 Slightly lift the right plate inserts 0 3 0 W AZZZV IT TTT AT yz7z77T4T 2 Fold the plate inserts to the left S IJ Z y a d l 0 B 0 1 AASV ITT TTT 7 T y i Operating Instructions Type 3 The right hand plate inserts in the lower basket can be folded across one another To ease the loading of large items LA y the two right hand plate inserts in the lower basket can be folded across o
26. ne another oy 1 ZZZU TTT TTI o Type 4 The two rear plate inserts in the lower basket can be folded across one another To ease the loading of large items the two rear plate inserts in the lower baskets can be folded across one another 17 Operating Instructions Loading Cups Glasses and Coffee Services f Load small delicate items and long pointed cutlery in the upper basket Arrange items of crockery on the folding cups racks so that they are Offset from each other and water can reach all items he cup racks can be folded up out of the way for tall items Lay or hang wine champagne and brandy glasses in the cut outs on the cup racks Glasses beakers etc can also be placed on the two rows of prongs on the left of the upper basket Operating Instructions Filling with Detergent cs 1 Only use dishwasher detergent Fill with detergent Prior to the start of a wash programme not for the pre wash pro gramme The detergent is released into the wash water during the programme Please observe the manufacturer s dosing and storage recommenda tions as stated on the detergent packaging The detergent compartment is on the inside of the dishwasher door If the lid is closed press rel
27. o a value of approx USD 14 billion in more than 150 countries around the world AEG Hausger te GmbH Postfach 1036 D 90327 N rnberg http www aeg hausgeraete de Copyright by AEG 822 946 783 00 1002 Subject to change without notice
28. o match the height of the appliance to that of surrounding units extend the threaded feet by unscrew ing use a screwdriver For built in dishwashers the rear feet should be adjusted from the front of the appliance using a screwdriver he drain hose inlet hose and mains cable must be laid such that they are free to move in the rear of the plinth recess so that they cannot be kinked or crushed Built Under Dishwasher see enclosed installation instructions Free Standing Appliances can be set up as stand alone without additional installation If the dishwasher is set up next to a gas or coal cooker a heat insulating non flammable plate must be mounted between the dishwasher and the cooker flush to the top edge of the work surface depth 57 5 cm The plate should have aluminium foil on the side fac ing the cooker Installation and Connection Instructions If the dishwasher is installed underneath a kitchen work surface the original work surface of the dishwasher is to be removed as follows ts 1 Unscrew the screws from the posi x tioning plates on the back 1 2 Slide the appliance s work surface approx 1 cm to the rear 2 3 Lift the work surface at the front 3 and remove N If the dishwasher is later used as a free standing appliance the original work surface must be re mounted lil The plinth on free standing appliances is not adjustable 31
29. on old hoses which have been used for another appliance Installation and Connection Instructions The following section is only applicable to dishwashers that have a safety valve on the threaded hose fitting for the tap Water inlet hose with safety valve After connecting the double walled water inlet hose the safety valve is next to the tap Therefore the water inlet hose is only under pressure while the water is running If the water inlet hose starts to leak during this operation the safety valve cuts off the running water and the draining pump in the dishwasher is switched on Please take care when installing the water inlet hose The distance between the bottom edge of the safety value and the floor on which the dishwasher is standing must be at least 30 cm The electrical cable for the safety valve is in the double walled water inlet hose Do not immerse the LL water inlet hose or the safety valve in water If the water inlet hose or the safety valve is damaged remove the mains plug immediately A water inlet hose with safety valve must only be replaced by your local Service Force Centre Place the water inlet hose in such a way that it is never higher than the bottom edge of the safety valve min 30cm 33 Installation and Connection Instructions 34 AN Water drain Drain hose The drain hose must not be kinked crushed or entangled Connecting the drain hose
30. programme see Pro gramme Table Power indicator light illuminates wash programme starts 23 Operating Instructions 24 AN iS 1 Interrupting the wash programme by opening the door of the dish washer Hot steam may escape when the door is opened Open the door care fully Open the door of the dishwasher The wash programme stops 2 Shut the door The wash programme continues Switching Off the Dishwasher p 1 When the wash programme is finished Turn the programme selector to the position Power indicator light goes out Hot steam may escape if the door is opened immediately after the end of the programme Open the door carefully Emptying the Dishwasher e The dishes should be allowed to cool down before removing them from the appliance as hot dishes can be sensitive to knocks Leave the dishes in the dishwasher for approx 15 minutes after the end of the programme so that they dry better and can cool down Empty the lower rack first then the upper rack This will avoid any water left on the upper rack dripping onto the dishes in the lower rack and causing water spots Care and Cleaning AN Do not under any circumstances use furniture care products or aggres sive cleaners f necessary clean the controls only with a soft cloth and pure warm water Occasionally check the internal containers door seal and water inlet for soiling clean if necessary Oper
31. rating Instructions i Open the door of the dishwasher Press the rinse aid compartment Fully open the rinse aid compartment Set the dose level Close the lid and press until it locks If rinse aid has run out wipe up with Adjusting Rinse Aid Dosing As the dishes are washed rinse aid is released from the dispenser into the wash water The dose is factory set at 4 and can be adjusted from 1 to 6 Only change the setting if streaks milky spots or dried on water marks are visible on glasses or crockery release button with your finger lid into place a cloth 13 Operating Instructions 14 In Daily Use Check the salt and rinse aid levels Load cutlery and dishes into the dishwasher e Fill with dishwasher detergent e Select a wash programme suitable for the cutlery and dishes e Start the wash programme Loading Cutlery and Dishes AN Sponges household cloths and any object that can absorb water should not be washed in the dishwasher For washing in the dishwasher the following cutlery dishes are not suitable Cutlery with wooden horn china or mother of pearl handles Plastic items that are not heat resistant Older cutlery with glued parts that is not temperature resistant Bonded cutlery items or dishes Pewter or copper items Lead crystal glass Steel items subject to rusting Wooden platters Items made from synthetic fibres are o
32. ter has not reached all parts The dish racks must not be overloaded The filter in the base of the washing compartment is dirty or incor rectly positioned Detergent was not used or too little was used In the case of scale deposits on the dishes the special salt container is empty or the water softener is incorrectly adjusted The drain hose is incorrectly laid The dishes are wet and dull Rinse aid was not used The rinse aid container is empty There are streaks milky spots or a bluish coating on glasses and dishes Decrease rinse aid dosing There are dried water drops on the glasses and dishes Increase rinse aid dosing The detergent may be the cause Contact the detergent manufac turer s consumer advisor 27 Operating Instructions Technical Data Capacity 12 place settings including serving dishes Permitted Water 10 2 mec Pressure 1 10 bar 210 100 N cm 0 1 1 0 MPa Information on the electrical connection is given on the rating plate on the inner edge of the dishwasher door on the right Electrical Connection Dishwasher Free Standing Appliances Dimensions 850 x 600 x 600 H x W x D in mm Max Weight 54 Kg Dishwashers that Can Be Integrated Built In Dishwashers Dimensions 820 880 x 596 x 570 H x W x D in mm Max Weight 50 Kg Dishwashers that Can Be Fully Integrated Dimensions 820 880 x 596 x 546 550 H x W x D in mm Max Weight 50 Kg C
33. wer during short programmes Therefore please use wash pro grammes with pre wash when using detergent tablets 21 Operating Instructions 22 Selecting the Wash Programme Programme Table Choose the most suitable wash programme with the aid of this table Coffee Service and Dessert Type of Dishes Dinner Service and Cooking Utensils Dishes In Addition T with non temperature with delicate resistant dishes glasses Type of Soiling e heavily soiled normally normally to lightly soiled e dried leftovers soiled lightly soiled particularly suited to the use of concentrated detergents Suitable Wash Qu i Programme NORMAL NORMAL ECO QUICK Turn programme switch to A A B C T NORMAL urn programme NORMAL x ECO 50 QUICK 50 selector to 65 50 Programme Sequence Pre Wash Pre Wash 3 Main Wash Main Wash Main Wash Main Wash Rinsing Rinsing Rinsing Rinsing Final Rinse Final Rinse Final Rinse Final Rinse Drying Drying Drying Consumption Figures 1 Duration 94 minutes 90 minutes 84 minutes 34 minutes Energy 1 45 kWh 1 24 kWh 1 24 kWh 0 8 kWh Water 18 litres 18 litres 14 litres 14 litres 1 The consumption figures were measured under standard conditions They are dependent on the loading of the racks Variations from these figures are therefore possible in practice 2 Test Programme Operating Instructions Starting the Wash Programme I 1 2 4 AN Check that when the dishes and
Download Pdf Manuals
Related Search