SnapStone 11-218-02-01 Installation Guide
Contents
1. liters bucket of cleaning water 1 2 full changing the water every 100 sq ft Grouting amp Caulking Use a hard rubber edged grout float Do not use a foam edged grout float Step 1 With float at a 45 degree angle spread SnapSys Urethane Flexible Grout diagonally pressing firmly to ensure joints are filled completely Step 2 With float at a 90 degree angle pull diagonally across joints removing excess grout from tile using the edge of the float like a squeegee Use caution not to pull grout out of filled joints Inspect grout joints and Deo maanani Pack additional grout if needed Coverage Tile Size 12x12 18x18 6x6 6x24 12x24 1 4 Grout line 50 55 80 90 30 35 N A 75 80 1 8 Grout line 110 N A N A 135 160 170 SnapSys Urethane Flexible Grout should not be used to fill in the expansion gap along the perimeter of the room In an environment exposed to moisture such as a bathroom a caulk should be used to seal the perimeter Initial Cleaning Remove grout residue AS YOU WORK particularly in warm dry climates Never grout more than 5 10 square feet before cleaning Step 1 With a lightly damp and nearly dry sponge gently wipe grout joints and tile surface ina circular motion Stop 2 loosening grout residue while make the joints smooth Do not use too much water this may result in over washing see our website for more information on over washing Step 22. Items Needed Rubber gloves Margin Trowel Hard rubber edged grout float 5 gallon bucket with a fresh water supply Sponge designed for cleaning grout Included in SnapSys Installation Tool Kita vailable at www snapsysinterloc com Things to Know SnapSys Urethane Flexible Grout is for use with the SnapSys Tile System which includes Avaire Zip Tile Eclipse and SnapStone It is not warranted or approved for other applications Using SnapSys Urethane Flexible Grout is a critical part of installing the SnapSys Tile System No other grout should be used These instructions are for installing SnapSys Urethane Flexible Grout over a SnapSys Tile floor Stir grout thoroughly before use Please note A milky liquid may be present at the surface and should be mixed in until a consistent grout texture is reached Do not add water or any other material to SnapSys Urethane Flexible Grout This will have an adverse effect on the product and will void all warranties Protect grout from freezing prior to opening and throughout curing process Acclimate the grout to a temperature of approximately 60 F 16 C 70 F 21 C SnapSys Flexible Grout may be applied as soon as you have finished installing your SnapSys Tile floor Remove grout residue AS YOU WORK using water and a sponge Do not use too much water Do not over wash please see our website for more information on over washing the sponge should be lig
3. Wipe the loosened grout residue diagonally rinsing sponge after every pass use each side of sponge only once between rinsing Check work as you clean Repair any low spots joints with additional grout Do not wash too vigorously just a light motion will suffice Final Cleaning After 24 hours use a sponge and water to remove any remaining grout residue this will have a shiny or smeared appearance on the surface of the tile Allow cleaned areas to dry and inspect the floor again Protect finished surface from light traffic for 24 hours at 70 F 21 C Regular traffic can resume after 72 hours A complete cure requires 28 days at 70 F 21 C and 50 relative humidity Never cover grout during curing If grout haze exists after 24 hours it may be removed using Krud Kutter Original Tuff Task Remover or Snapsys Urethane Grout Cleaner and a nylon scrubber pad taking care to avoid getting the cleaner in the grout lines For more information see our Grout Haze Removal Instructions on our website at www snapsysinterloc com Low spots joints can be touched up after 24 hours Do not expose grout to stains or cleaners for 7 days No sealing required IMPORTANT INFORMATION The SnapSys _Interloc System must be installed over a structurally sound floor that is clean dry smooth and flat within a tolerance of 1 4 in 10 and 1 16 in 12 To determine if a floor is flat use a straight edge t
4. htly damp and nearly dry Never grout more than 5 10 square feet before cleaning Protect finished surface from light traffic for at least 24 hours at 70 F 21 C Regular traffic may resume after 72 hours at 70 F 21 C and 50 relative humidity Do not expose grout to stains or cleaners for 7 days Use Krud Kutter Original or Krud Kutter Tough Task Remover or UGC Urethane Grout Cleaner to cleanup any grout residue that remains on the tile surface after 24 hours See our website for Grout Haze removal instructions KEEP OUT OF REACH OF CHILDREN Surface Preparation Conduct a final floor inspection verifying all tabs are fully engaged all grout intersections are properly aligned forming a grout joints are clean dry and free from debris Surface temperature must be above 60 F 16 C and below 80 F 27 C Preparation for Grouting Liquid may be present on the surface of the grout when opened due to settling Please note SnapSys Flexible Grout is measured by weight not volume Extra space is left in the bucket to allow for stirring Working time of grout is 2 to 3 hours at 70 F 21 C Working time is affected by many variables including surface and room temperatures and humidity Warmer climates will shorten working time while colder conditions will extend working time DO NOT add any water liquid or other material to SnapSys Flexible Grout Prepare one 5 gallon 18 93
5. o identify the high and low areas The high spots need to be planed and low areas need to be filled cement based SNAPSYS STOP Please carefully read all with a instructions patching compound Be sure the tabs are fully interlocked When installing the SnapSys Interloc System listen for a snap sound to ensure the tiles are fully engaged It is also important to visually examine the tabs to make certain there is a complete connection Use only with Snapsys Urethane Flexible Grout Other grouts are not sufficiently flexible to handle the movement associated with a floating floor and will fail Please refer to the website for more installation instructions www snapsysinterloc com YOUR WARRANTY IS VOID IF ANY OF THESE IMPORTANT GUIDELINES ARE NOT FOLLOWED Cleaning Tips Use a sponge designed for cleaning grout This has a denser texture and will make it easier to remove grout haze during the cleaning process Keep water clean Itis best to rinse sponge in a 5 gallon bucket filled to the top with water This allows grout from the sponge to sink to the bottom keeping the top area clean for rinsing When cleaning the grout don t use too much water do not over wash the sponge should be lightly damp and nearly dry Grout Haze Removal instructions can be found on our website www snapsysinterloc com Long Term Care SnapSys Flexible Grout may be cleaned using Soft Scrub with Bleach and a s
6. oft bristled brush Do not use a vinegar cleaner enzyme cleaner or steam cleaner See Care amp Maintenance page on our website for more information Questions Call toll free 1 877 263 5861 www snapsysinterloc com REV A1113 162013 Colle LLC AI rights esened Snaysnieocis a registered radar of Colle LL
Download Pdf Manuals
Related Search