Home

Electrolux EDI 96150 User's Manual

image

Contents

1. Cleaning the filter area The filter area does not have to be cleaned after every drying cycle but should be checked regularly and cleaned of fluff if necessary You will need to undertake the following to clean the filter area 1 Remove lint filter see chapter on Cleaning lint filters 2 Remove fluff from the entire filter ar ea Itis best to use a vacuum cleaner for this purpose 3 Replace the filter Clean the door seal Wipe the door seal using a damp cloth immediately after the Iron Aid or drying cycle cleaning and maintenance electrolux 29 30 electrolux cleaning and maintenance Emptying the condensed water container Empty condensed water container after every drying cycle If the condensate tank is full an active programme will break off automatically and the CONTAINER display will light up In order to continue the programme the condensed water container must first be emptied A Warning The condensate is not suitable for drinking or for preparing foodstuffs 1 Pull drawer containing condensed water container all the way out 1 and pull up the condensed water container s drain age pipe as far as it will go 2 2 Pour out the condensate into a basin or similar container 8 Push drainage pipe in and refit con densed water container If the programme has been interrupted as aresult of the con
2. Levelling the appliance The four feet of the appliance are pre adjusted Large degrees of unevenness can be compensated for by individually adjust ing the height adjustable screw feet To do this lift the appliance and turn the adjustable feet in or out Important Do not use pieces of wood cardboard or such like to level out une venness in the floor but adjust the height adjustable screw feet instead Special accessories The following special accessories are available from your Electrolux Service Force Centre or your specialist dealer Intermediate installation kits for stacked washer and iron aid appli ance These intermediate installation kits can be used to arrange the iron aid appli ance and an automatic Electrolux wash ing machine 60cm wide front loading as a space saving washer iron aid stack The automatic washing machine is at the bottom and the iron aid appli ance is at the top Two versions can be supplied without stacker plate with extractable stacker plate Read the manual supplied with the in stallation kit carefully special accessories electrolux 41 Door reversal instructions To make it easier to load or unload the GB laundry the door can be reversed SE Reversing the door is not possible if after this operation the appliance result in stalled behind a door with hinge on the opposite side to that of the appliance A Warning The door may only be re versed by q
3. button pressed and load volume too big Load volume too big Laundry insufficiently pre drained Colour fastness of textiles GB Select a different programme the next time you dry see section Overview of programmes Clean lint filter Clean heat exchanger Observe recommended loads Uncover ventilation slots in base area Clean inside surface of drum and drum paddles Adjust using the DRYNESS GRADO DE SEC additional func tion See chapter on Drying se lecting additional functions Turn the programme knob to O OFF Reset programme Select time programme or higher drying level e g amp EXTRA EX TRA SECO instead of H CUP BOARD SECO ARMARIO Empty condensed water contain er then start programme with the START PAUSE INICIO PAUSA button Automatic process there is no fault with the appliance Clean fluff filter Clean heat exchanger DELICATE DELICADO is only suit able for use with loads of up to 3kg Reduce load volume Laundry must be adequately pre drained Check colour fastness of textiles Only treat textiles together if they are a similar colour 38 electrolux technical data Technical data es CE This appliance conforms with the 89 336 EEC dated 03 05 1989 EMC following EU Directives Directive inclusive of Amending Di 73 23 EEC dated 19 02 1973 Low rective 92 31 EEC Voltage Directive 93 68 EEC dated 22 07 1993 CE Marking
4. q SYNTHETICS wet SINT TICOS dry amp x REFRESH VENTILACI N By odours from dry outerwear Garments are softened and smoothed and require a lot less ironing If laundry is wet a dry ing programme is automatically activat ed before the Iron Aid programme starts Exception The 43 REFRESH VENTI LACION programme must only be used for dry laundry Odour removal worn clothing Iron Aid washed garments Smoothes worn clothing X X X X X X X X X X X X X X id 12 electrolux prior to using for the first time Prior to using for the first time In order to remove any residues which 1 Turn the programme knob to may have been produced during pro O TIME TIEMPO duction wipe the dryer drum with a 2 Press the TIME TIEMPO button re damp cloth or carry out a brief drying cy peatedly until 8 35 appears in the dis cle O TIME TIEMPO programme of play 30 min with damp cloths in the ma 5 Press the START PAUSE INICIO oning PAUSA button Sorting and preparing laundry Sorting laundry general e Sorting by fabric type e Sorting by care label The care labels Cotton linen for programmes in mean the amp COTTON ALGODON pro gramme group Mixed fibres and synthetics for programmes in the A SYNTHETICS SINTETICOS programme group O C E E Dry at reduced temperature Drying in the Drying in the tumble dryer Dry at normal ps SPECIAL CARE tumble ee
5. Directive Height x width x depth 85 x 60 x 60 cm Depth with loading door open 109 cm Height can be adjusted by 1 5cm Weight when empty approx 46kg Load depends on programme 1 max 6kg Energy consumption in accordance with IEC 1121 6kg of cotton pre drained at 1000 rpm 3 7kWh programme 4 COTTON H CUPBOARD ALGODON SECO ARMARIO Area of use Domestic permissible ambient temperature 5 C to 35 C 1 Different load weights may be needed in some countries due to different measuring methods Consumption values The consumption values have been es They may deviate when the machine is tablished under standard conditions operated in domestic circumstances Energy Programme consumption in kWh amp COTTON I CUPBOARD ALGOD N SECO ARMARIO amp COTTON 4 HAND IRON 6 m ALGOD N SEMISECO A SYNTHETICS H CUPBOARD P T SINT TICOS SECO ARMARIO 2 1 pre drained at 1000 rpm pre drained at 1200 rpm corresponds to COTTON HAND IRON ALGOD N SECO PLANCHA programme installation safety instructions electrolux 39 A E Installation safety instructions Important The appliance must be The door of the appliance must not moved in vertical position for trans be able to be blocked by house port doors or other appliance doors Before first starting up all parts of e Do not install on a carpet with a high the transport safety equipment must pile Air circulation at the ventilation be remov
6. Drying cycle Energy in KWh 800 1000 1200 1400 1800 4 2 3 6 3 2 3 0 2 5 always keep the ventilation slots on the base of the appliance unob structed use the loading volumes specified in the programme overview ensure you have good ventilation in the installation room clean the micro fine filter and fine strainer after each drying or Iron Aid cycle 70 60 53 50 42 4 0 3 7 3 8 3 1 2 6 appliance description electrolux 9 Appliance description Filler neck for water tank c Drawer with condensed water container Control panel Fine strainer int filter DY a_i UN Steam nozzle Lamp for inside light Micro fine filter Wh Large mesh filter lint filter lint filter Type plate x J ll Button for opening LY door in plinth Loading door interchangeable stop Screwed feet Z Drainage hose Air slots with height adjust for water tank ment 10 electrolux control panel Control panel Maintenance displays DELAY HEAT EXCHANGER Programme knob and TIMER CLEAN FILTER On Off switch Display button CONTAINER 5 o I S T E ge 5 Ee Extra Seco 23 Fl algod n Seco Armario 1 F pem N sint ticos e 8 Y EJ E Diferido Tm f N Dans SF opos Ll e ee Bd MER MER amp E de adds g xtra Seco E int ticos Seco Armario ij n S Ventila
7. the water tank s filler neck 2 cleaning and maintenance electrolux 31 32 electrolux cleaning and maintenance 2 Fill with distilled water from the can ister provided up to the MAX mark inside the container 3 Push filler neck and drawer with con densed water container back in B The water tank has a volume of ap prox 1 3 litres This is sufficient for around 4 10 Iron Aid programmes with garment steaming depending on the selected volume of steam programme and the corresponding steam phases during the crease guard phase You can easily check the level of water in the tank at any time by looking at the fill indicator in the viewing window The maximum fill level is indicated by the MAX mark An overflow guard prevents the contain er from being overfilled The water tank indicator on the display lights up as soon as the fill volume in the tank falls below 500 ml when you start a programme this corresponds to the maximum volume of water required for the Iron Aid programme that uses the most steam including the crease guard phase This prevents an Iron Aid pro gramme from being interrupted be cause of an empty water tank Emptying the water tank for long periods of disuse If Iron Aid programmes are not run for more than three weeks the tank should be emptied and refilled with fresh dis tilled water if required 1 Open door in plinth in front o
8. ATE symbol ap pears in the display BUZZER ALARMA Q The appliance is supplied with the BUZZER ALARMA function activated When the drying cycle has finished an intermittent acoustic signal will sound Each time a button is pressed or a pro gramme is changed using the pro gramme knob an audible signal is also Set to sound The button is used to switch the func tion on or off When the function is ac tive the BUZZER ALARMA symbol appears in the display overview of drying programmes electrolux 25 i Delicado Alarma 26 electrolux overview of drying programmes TIME TIEMPO To select the programme duration after setting the TIME TIEMPO pro gramme You can select a programme duration from 10 mins to 3 hrs in 10 minute steps 1 Turn the programme knob to the TIME TIEMPO programme The display will show amp 5 corresponding to the S COOLING programme 2 Press the TIME button repeatedly until the desired programme duration is shown in the display e g 3220 for a programme of 20 minutes If the programme duration is not select ed the duration is automatically set to 10 mins To set the timer delay and the child safe ty device please refer to the chapter on Iron Aid setting the timer delay Set ting the child safety device 88 88 Tiempo Starting a drying programme Press the START PAUSE INIC
9. Aid treatment clothes must be removed one garment at a time during the anti crease phase and hung imme diately on a clothes hanger to dry for at least 5 15 mins depending on fabric and selected steam level Do up the buttons and tug the garment into shape paying particular atten tion to cuffs and seams 4 Turn the programme knob to O OFF Important After each drying cycle Clean the micro fine filter and fine fil ter Drain the condensed water contain er See section Cleaning and mainte nance 5 Close door Drying drying electrolux 23 Overview of drying programmes Additional functions El Programmes 5 oS iere xs BEXTRA ek EXTRASECO 9 5 6 CUPBOARD Ae OG SECO 9 Oz ARMARIO DAMP SEMISECO 2x9 A EXTRA 3kg 8 EXTRA SECO ne D F CUPBOARD skg lt p SECO ae ARMARIO DAMP SEMISECO 9 TIME TIEMPO ike 8 SILK SEDA uke 7 AE 6 WOOL Ku LANA 1kg 1 Press the DELICATE button DELICATE DELICADO e Q e e e e e e e e e e e e AUTO AUTO DRYNESS GRADO DES AUTO Application properties Thorough drying of thick or multi layered fabrics e g terry towelling items bathrobes Thorough drying of fabrics of even thicknesses e g terry towelling items knitwear towels For normal thickness cotton or lin en laundry e g bedding table linen Thorough drying of thick or multi layered fabrics e g pullovers bed di
10. IO PAU SA button The programme is started The programme progress display shows drying progress The symbols for 5 DRYING and S COOLING appear in the display one after the other The number of droplets in the dryness indi cator gradually goes down as the drying process progresses Changing a programme To change a programme which has been selected by mistake once the pro gramme has started first turn the pro gramme selector to O OFF and then reset the programme The programme can no longer be changed directly once the pro gramme has started If you never theless attempt to change the programme with the programme knob or an additional function but ton except the BUZZER ALARMA button the START PAUSE INICIO PAUSA button and Err will flash in the display The drying programme is not however affected by this Putting in extra items or taking items out before end of pro gramme 1 Open loading door A Warning Laundry and drum can bec ome hot Risk of burns 2 Load or remove laundry items starting a drying programme electrolux 27 3 Close loading securely Lock must audibly lock 4 Press the START PAUSE INICIO PAUSA button to continue the dry ing cycle Drying cycle complete removing laundry Once the drying programme has fin ished 3 ANTICREASE lights up in the display If the ds BUZZER is activated an audible signal sounds at regular inter vals B The drying cycle is a
11. Thinking ef yor_ user manual dl manual de instrucciones Electrolux Iron Aid EDI 96150 We were thinking of you when we made this product Welcome to the world of Electrolux Thank you for choosing a first class product from Electrolux which hopefully will provide you with lots of pleasure in the future The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable You will find some examples on the cov er in this manual Please take a few min utes to study this manual so that you can take advantage of the benefits of your new machine We promise that it will provide a superior User Experience delivering Ease of Mind Good luck electrolux 3 4 electrolux Contents Safety Disposal Environmental tips Appliance description Control panel Prior to using for the first time Sorting and preparing laundry Starting up for the first time Iron Aid Steam System Overview of Iron Aid programmes Starting an Iron Aid programme Drying Overview of drying programmes Starting a drying programme Cleaning and maintenance What to do if Technical data Consumption values k Nal 12 12 15 14 16 21 28 23 27 28 36 38 38 Installation safety instructions Removing transport safety equipment Special accessories Guarantee Customer Service Service The following symbols are used in this user manual A Important information concerning your person
12. al safety and information on how to avoid damaging the appliance i General information and tips 9 Environmental information 39 40 41 42 43 safety electrolux 5 Important Only operate the Iron Aid programmes with distilled water Mains water causes damage to the appliance A Safety Before first starting up e Note the Installation and con nection instructions Important The appliance must be moved in vertical position for trans port e Before first starting up check the machine for any damage incurred during transport Never connect up a damaged machine If parts are dam aged contact your supplier Intended use The appliance is intended for drying and iron aid treatment of standard laundry in domestic applications This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experi ence and knowledge unless they have been given supervision or in struction concerning use of the ap pliance by a person responsible for their safety e Donot dry unwashed items with dry ing programmes e Conversions or modifications to the appliance are not permitted e When using dry cleaning sets Only use those products which are de clared as suitable for the appliance by the manufacturer e Items such as foam rubber latex foam shower caps waterproof tex tiles rubber backed articles and clothes or pillows fitted
13. anger You could damage it an cause leaks 7 Clean heat exchanger It is best to use a brush or to rinse thoroughly with a shower head 8 Replace heat exchanger and lock into place turn both lock washers outwards until they snap into place 9 Close base door 8 The appliance will not operate if the HEAT EXCHANGER indicator is still lit A Caution Never operate the appli ance without the heat exchanger cleaning and maintenance electrolux 35 Cleaning the drum N SB Important Do not use scourers or steel wool to clean the drum B Lime in the water or laundry care products may form a barely visible lining on the inside of the drum The degree to which the laundry has been dried is then no longer detect ed reliably The laundry is damper than expected when removed from the appliance Use a standard domestic cleaner e g vinegar based cleaner to wipe down the inside of the drum and drum ribs Clean control panel and housing A Important Do not use furniture cleaners or aggressive cleaning agents to clean the appliance Use a damp cloth to wipe down the control panel and housing Changing the light bulb for interi or lighting Important The bulb for the interior lighting must be changed by our Cus tomer Care Department 36 electrolux what to do if What to do ff Remedying small malfunctions If during operation the error code E If the error appears again please con plus nu
14. cables must not be used Risk of fire from overheating The height adjustable screw feet must never be removed Do not spray down the appliance with jets of water Risk of electric shock Do not lean on the open door The appliance may tip over If you interrupt the drying or Iron Aid programme laundry or drum may be hot Risk of burns Take care when removing the laundry Take care when interrupting the Iron Aid programme Do not open the door of the appliance during the evaporation phase Hot steam can cause burns The evaporation phase is indicated by the animation of the steam symbol in the display Never stop the appliance before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissi pated The final part of a drying cycle occurs without heat cool down cycle to en sure that the items are left at a tem perature that ensures that the items will not be damaged A Caution hot surface Do not touch the surface while the appliance is running Disposal C Packaging material The packaging materials are envi ronmentally friendly and can be re cycled The plastic components are identified by markings e g PE gt PS lt etc Please dispose of the packaging materials in the appro priate container at the community waste disposal facilities CJ Old appliance The symbol K on the product or on its packaging indicates that this product may not be trea
15. ci n Semiseco Liam Dil tiempo W seda Function buttons START PAUSE button What is shown in the display Start time Iron Aid preselection programme LOAD CARGA Drying irs Anticrease i Degree of l vie J S dryness SHE ALLK Te aye FB WS a pedo hi Water tank AUTO ATO AUTO indicator f M IN FA icc eb Start time t me MENI MEK i Ej qe Bb Sume duration DRYNESS GRADO DELICATE BUZZER display DE SECADO DELICADO ALARMA Steam display Child safety device control panel electrolux 11 Function overview Iron Aid M Steam System This appliance can be used both as a dryer and to condition clothes Iron Aid to treat garments using steam When it is operating as a dryer there are 9 available programmes When it is operating as a steam appli ance there are 4 available programmes for smoothing and removing odours from wet and dry laundry and the amp REFRESH VENTILACI N pro gramme for smoothing and removing Programmes Cotton 3 EXTRA Algod n EXTRA SECO we Cotton I CUPBOARD ae Algod n SECO ARMARIO Cotton HAND IRON T Algod n SEMISECO Synthetics A EXTRA T Sint ticos EXTRA SECO Synthetics M CUPBOARD Um Sint ticos SECO ARMARIO Synthetics HAND IRON A Sint ticos SEMISECO amp WOOL LANA we W SILK SEDA we TIME TIEMPO we COTTON ALGOD N E SYNTHETICS wet z SINT TICOS dry f amp COTTON ALGOD N E e
16. d Iron Aid appliance Do not place objects on the appliance These may fall off dur ing operation The covering bonnet of the bulb for the drum light must be screwed down tightly Child safety Keep packaging away from children There is a risk of suffocation Children often do not recognise the hazards associated with electrical appliances Children should be su pervised to ensure that they do not play with the appliance Make sure that children and small animals cannot climb into the appli ance s drum Could endanger life Keep the appliance door shut when ever it is not being used General safety Only specialists may undertake re pairs on the appliance Never start up the appliance if the mains cable is damaged or if the op erating screen operating plate or base area are damaged so that the inside of the machine is open and accessible Should the appliance power supply cable need to be replaced this must be carried out by our Service Centre Switch off the appliance before all cleaning care or maintenance work Also disconnect the mains plug from the socket or with permanent con nections switch off the LS switch in the fuse box and or fully unscrew the screwed in fuse Disconnect the machine from the power supply during long pauses in operations When removing from the socket never pull the mains plug by the ca ble instead take a hold of the plug Manifold plugs couplings and exten sion
17. d water provided if there is not yet any condensed water from previous drying programmes see chapter on Cleaning and Maintenance Emptying condensed water container If after an Iron Aid programme is select ed the ef water tank indicator on the display lights up you will need to fill up the water tank with distilled water Oth erwise you will not be able to start any Iron Aid programme A Important Only fill the water tank with distilled or fully desalinated water Do not use tap water or addi tives You can also use the con densed water from the condensed water container as long as you filter it first use the canister supplied with the filter fitted see figure oppo site 1 Pull drawer containing condensed water container out a little 1 then pull out the water tank s filler neck 2 2 Fill with distilled water from the can ister provided up to the MAX mark inside the container 3 Push filler neck and drawer with con densed water container back in When dry all textiles not specifically prohibited in the chapter Sorting and preparing laundry may be treated with the Iron Aid Steam Sys tem Wet textiles may only be treat ed if they are labelled as suitable for dry programmes iron aid steam system electrolux 15 16 electrolux overview of iron aidtm programmes Overview of Iron Aid M programmes Additional functions Programmes Applicat
18. densed water con tainer being full Press the START PAUSE INICIO PAU SA button to continue the drying cycle The condensed water container has a volume of approx 4 litres This is sufficient for around 6kg of laundry which has previously been spun at 1000 revolutions minute 4 The condensed water be used as distilled water e g for steam irons However first filter the condensed water to remove any residues and small pieces of fluff Using the attached canister to filter Pour the water out of the container straight through the filter at the top of the canister Fill water tank You must fill up the water tank before using an lron Aid programme for the first time Use the distilled water provided if there is not yet any condensed water from previous drying programmes see chapter on Cleaning and Maintenance Emptying condensed water container If after an Iron Aid programme is select ed the Jef water tank indicator on the display lights up you will need to fill up the water tank with distilled water Oth erwise you will not be able to start an Iron Aid programme A Important Only fill the water tank with distilled or fully desalinated water Do not use tap water or addi tives You can also use the con densed water from the appliance s container as long as you filter it first 1 Pull drawer containing condensed water container out a little 1 then pull out
19. ed The machine may oth holes will be hindered erwise be damaged Ensure that the appliance is not e The appliance must not be built in standing on the mains cable e Before starting up for the first time e Install the machine horizontally ensure that the nominal voltage and type of current specified on the ap pliance s rating plate match the nom inal voltage and type of current at the installation site The electrical fuse required can also be found on the rating plate e Always connect the machine to an earthed socket in accordance with current wiring regulation The manufacturer declines any re sponsibility for damage or injury through failure to comply with the above safety precaution e With permanent connections A per manent connection may only be es tablished by an authorised specialist electrician Do not install appliance in rooms at risk of frost e Do not install the appliance behind a door that locks a sliding door a door with a hinge that lies oppo site the hinge of the appliance 40 electrolux removing transport safety equipment Removing transport safety equipment Caution Before first starting up all parts of the transport safety equipment must be removed 1 Open loading door 2 Pull off adhesive strips from inside 85885 T meee machine on top of drum 5 OS GB ML 3 Remove foil hose and polystyrene padding from the machine
20. es fabric types and the corre sponding optimum steam level If too high a steam level is selected garments may lose their shape If too low a steam level is selected creases may remain Selecting additional functions The additional functions available for the lron Aid programmes are BUZZER ALARMA TIME DELAY INICIO DIF ERIDO and the CHILD SAFETY DE VICE BUZZER ALARMA The appliance is supplied with the BUZZER ALARMA function activated When the drying cycle has finished an intermittent acoustic signal will sound Each time a button is pressed or a pro gramme is changed using the pro gramme knob an audible signal is also set to sound The button is used to switch the func tion on or off When the function is ac tive the BUZZER ALARMA symbol appears in the display overview of iron aidtm programmes electrolux 19 Alarma Tiempo EX M Alarma 20 electrolux overview of iron aidtm programmes Delay timer With the DELAY INICIO DIFERIDO button you can delay the start of a programme by between 30 minutes 32 and a maximum of 20 hours 25h 1 Select the programme and addition al functions 2 Press the DELAY INICIO DIFERIDO button as many times as necessary until the required start delay appears on the display e g teh if the pro gramme is to be started in 12 hours If the display is showing 23h a
21. f heat exchanger see chapter on Cleaning the heat exchanger and place a col lecting container in front of the appli ance 2 Pull out the drainage hose under neath the heat exchanger 1 3 Remove the plug from the end of the hose 2 and allow the water to drain into the collecting container 4 Then seal the hose again and push it back into its original position 5 Close door in plinth cleaning and maintenance electrolux 33 34 electrolux cleaning and maintenance Cleaning heat exchanger If the HEAT EXCHANGER display is illu minated the heat exchanger needs to be cleaned A Caution Operating when the heat exchanger is clogged with lint can damage the appliance This also in creases energy consumption 1 Open loading door 2 Open base door To do this press the release button located beneath the loading aperture and open the base door to the left 3 Remove lint from the inside of the door and the heat exchange cham ber Wipe the door seal with a damp cloth 4 Turn both lock washers inwards 5 Use the handle to pull the heat ex changer out of the base and carry it horizontally to prevent any remaining water from spilling 6 To empty the heat exchanger hold vertically over a washing up bowl Sse Caution Do not use sharp objects to clean the heat exch
22. ine on switching light on Turn the programme knob to any pro gramme The machine has been Switched on When the loading door is opened the drum is illuminated Opening loading door loading laundry 1 Open loading door Push aaainst the loading door push point E9 starting up for the first time electrolux 13 items Colours may fade check col our fastness of fabric when damp in an inconspicuous area A e Donot use dry cleaning sets such as dryel in combination with Iron Aid programmes Preparing laundry general e To avoid laundry becoming tangled close zips button up duvet covers and tie loose ties or ribbons e g of aprons e Empty pockets Remove metal items paper clips safety pins etc e Turn items with double layered fab rics inside out e g with cotton lined anoraks the cotton layer should be outermost These fabrics will then dry better Special notes about Iron Aid e Before treating garments with an Iron Aid programme remove stains by washing or using localised stain re 2 Load your laundry do nat force it in overload the machine A Caution Be careful not to trap laun dry in between the loading door and rubber seal 3 Close loading door securely Lock must audibly lock 14 electrolux iron aid steam system Iron Aid M Steam System Fill water tank You must fill up the water tank before using an Iron Aid programme for the first time Use the distille
23. ion properties Ea 12 c ro fe E te c BUZZER ALARMA D 3 gt F COTTON 10k ES e For1 5 cotton shirts Min 80 natural wet ALGODON 2 fibres cotton linen etc dry SYNTHETICS 1 0k A e For 1 5 synthetic shirts Max 20 nat wet SINTETICOS dE ural fibres cotton linen etc dry amp COTTON 3 0k e For smoothing cotton garments Min wet ALGODON RSS 8096 natural fibres cotton linen etc dry For smoothing easy care garments A SYNTHETICS wet SINT TICOS 1 5kg e 20 natural fibres cotton linen dry For one suit or up to two suit jackets or amp REFRESH A e pairs of trousers or similar garments d VENTILACION Also suitable for removing odours For y dry garments only Allinformation on applications is for guidance only Smoothing results may vary depending on the selected programme and especially the fit tings and material properties of the textile The results can be improved if necessary by using different pro grammes and steam volumes For example some textiles containing more than 20 synthetics but with the right fittings may behave more like cotton textiles in an Iron Aid programme You may therefore get better smoothing results by select ing a cotton Iron Aid programme B Given the wide range of different textile grades and properties that can be manufactured today using different mechanical and chemical processes we recommend running the fi
24. l function but ton except the BUZZER ALARMA button the START PAUSE INICIO PAUSA button and Err will flash in the display The drying programme is not however affected by this Putting in extra items or taking items out before end of pro gramme 1 Open door 2 Load or remove laundry items 3 Close door securely 4 Press the START PAUSE INICIO PAUSA button to continue the dry ing cycle 22 electrolux starting an iron aidtm programme Iron Aid programme complete removing laundry After the Iron Aid phase has ended 0 00 is illuminated and the message ANTICREASE appears in the display If the d BUZZER ALARMA has been activated an audible signal sounds at regular intervals i The Iron Aid programme is automat ically followed by an anti crease phase including brief steam phas es which lasts around 90 minutes The drum rotates during the anti crease phase This keeps the laundry loose and free of creases It can be removed at any point during the anti crease phase ex cept during steam phases look for steam animation in the display Laun dry should be removed as quickly as possible 1 Open the loading door to remove the laundry 2 Before removing the laundry remove fluff from the micro fine filter It is best to use a damp hand for this purpose See Cleaning and maintenance section 3 Remove laundry one garment at a time A To retain the effects of the Iron
25. laundry after a few minutes the appliance will show the correct pro gramme duration for the Iron Aid pro gramme including the preceding drying programme As soon as the right level of dryness is reached the Iron Aid programme will start automatically The steam indicator shows the progress of the Iron Aid pro gramme in the display The individual steam phases are shown by gt animated clouds of steam IN Important During the steam phases that form part of the Iron Aid pro gramme and also the anti crease phase represented by animated clouds of steam in the display the loading door cannot be opened Risk of burns If the lef water tank indicator lights up when you select an Iron Aid programme the programme cannot be started You will need to fill the water tank first see section on Cleaning and maintenance filling water tank starting an iron aidtm programme electrolux 21 i It is normal for the appliance to make noises during an Iron Aid or drying pro gramme if garments with hard parts such as metal buttons are put in the drum Changing a programme To change a programme which has been selected by mistake once the pro gramme has started first turn the pro gramme selector to O OFF and then reset the programme B The programme can no longer be changed directly once the pro gramme has started If you never theless attempt to change the programme with the programme knob or an additiona
26. len im Ausland In diesen Landern gelten die Ga rantiebedingungen der rtlichen Partner Diese k nnen dort ein gesehen werden Further after sales service agencies overseas In these countries our AEG Electrolux agents own guaran tee conditions are applicable Please obtain further details di rect Autres agences trang res as surant le service apres vente Dans ces pays les conditions de garantie des concessionnaires de la r gion sont valables Vous pouvez les consulter sur place Otros puntos de Postventa en el extranjero En estos pa ses rigen las condici ones de nuestros representantes locales las cuales pueden ser consultadas all mismo Ulteriori uffici del servizio tecnico assistenza clienti all estero In questi paesi sono valide le condizioni di garanzia dei part ner locali Queste condizioni possono essere esaminante sul luogo Servicos de assist ncia t cnica no estrangeiro Nestes pa ses s o v lidas as con dic es de garantia dos concessi on rios locais podendo ai ser consultadas Tov bbi vev szolg lati iro dak k lf ld n Ezekben az orszagokban a mi AEG Electrolux vev szolg la tainkn l saj t j t ll si felt telek alkalmazhat k A tov bbi ada tokat k rj k k zvetlen l sze rezz k be Servisne slu be Na garancijskem listu boste na li seznam poobla enih servisnih slu b AEG Electrolux service electrolux 43 Service In the event of technical faul
27. mber or letter appears on the tact the Customer Care Department multi display Switch the appliance off stating the error code and on again Reset programme Press the START PAUSE INICIO PAUSA button Plug in at mains socket Check O fuse in fuse box domestic installa fuse is not working correctly Washing machine does ton not work Door is open Close door Press the START PAUSE INI Press the START PAUSE INICIO CIO PAUSA button PAUSA button Programme selector in O OFF Turn the programme selector to position any programme Drum light is not working Defective light bulb Replace light bulb see next sec tion icm o progiemme coes Water tank is empty Fill water tank not start Wrong programme selected e g SYNTHETICS e SINT TICOS instead of Note the composition of the fabric COTTON ALGODON Too low a LOAD CARGA Set a higher LOAD CARGA steam level set steam level Too many garments in machine or garments that are too differ np d i a gar After an Iron Aid pro ent i gramme garments are Remove clothes quickly one at a not sufficiently smooth Clothes are not removed until the anti crease phase is fin ished time from the machine as soon as possible after the start of the anti crease phase Garments not hung on clothes Hang garments on clothes hang hangers and or not tugged into ers do up buttons and tug gar shape ments into shape Reshape multi layered garments b
28. nd you press the button again the time de lay will be cancelled The display will show 5 and then the duration of the selected programme 3 To activate the delay timer press the START PAUSE INICIO PAUSA but ton The amount of time remaining until the programme is set to start is continuously displayed e g 15h th 13h 30 etc Child safety device The child lock can be set to prevent a programme being accidentally started or a programme in operation being acci dentally changed The child safety device locks all buttons and the programme knob The child safety device can be activated or deactivated by holding down the BUZZER ALARMA and TIME TIEMPO buttons simultaneously for 5 seconds Before programme is started Appli ance cannot be used After programme is started Pro gramme in operation cannot be changed The symbol appears in the display to indicate that the child safety device is activated The child safety device is not deactivat ed once the programme comes to an end If you want to set a new programme you must first deactivate the child safety device Starting an Iron Aid pro gramme Press the START PAUSE INICIO PAU SA button The programme is started First the drying phase indicator appears in the display The display will also show the pro gramme duration for the selected Iron Aid programme not including the addi tional drying phase With wet
29. ng table linen For thin fabrics which are not ironed e g easy care shirts table linen baby clothes socks lingerie with bones or wires For thin textiles which are still to be ironed e g knitted items shirts For further drying of individual items of laundry or for small volumes of less than 1kg You can select a programme duration from 10 mins to 3 hrs in 10 minute steps Special programme for drying silk using warm air and gentle move ment Special programme for drying woollen fabrics with minimum physical stress Sorting and pre paring washing Recommenda tion Remove fabrics immediately after drying as no anti crease pro gramme follows OO C3 FA O 3 31 6 O 7 go 24 electrolux overview of drying programmes Selecting the programme Use the programme selector to set the programme you require The probable programme run time is displayed in minutes on the multi display Selecting additional functions You can choose from the additional functions DRYNESS GRADO DE SEC ADO DELICATE DELICADO BUZZER ALARMA and TIME TIEMPO if a TIME TIEMPO programme has been selected The symbols of the functions available for the selected pro gramme are shown in the display DRYNESS GRADO DE SEC i If laundry comes out of the machine too damp after a standard drying pro gramme you can increase the drying re sult by using the DRYNESS GRADO DE SEC func
30. not possible in principle temperature DELICADO button possible SECO programme Items may A shrink e Wool and wool like textiles can be Important Do not place in the appli dried using the WOOL LANA ance any wet laundry which is not programme Before the drying cycle specified on the care label as being spin the woollen textiles as well as suitable for tumble drying possible max 1200 rpm Only dry This appliance can be used for all wet woollen textiles together which are similar or the same with respect to material colour and weight Please dry heavy laundry items made of wool separately laundry items which are labelled as suit able for tumble drying e Do not dry new coloured textiles to gether with light coloured laundry items Textile colours may bleed e Do not dry cotton jersey and knit wear with the EXTRA EXTRA Special notes about Iron Aid e The following textiles cannot be treated using an Iron Aid pro gramme woollen knitwear leather textiles with large metal wooden or plastic parts textiles with rusting metal parts oilskins or wax cotton gar ments A e Tosmooth or freshen laundry with an lron Aid programme sort laundry by size weight material and colour Only smocth textiles together that are similar in terms of size weight material and colour A e Do not dry new coloured textiles to gether with light coloured laundry Starting up for the first time Switching mach
31. occur in few cas es can be remedied by ironing 18 electrolux overview of iron aidtm programmes Selecting the programme Use the programme selector to set the programme you require The estimated programme duration without drying cy cle in minutes appears in the display Select steam level LOAD CAR GA To achieve the best results differ ent steam levels are required for dif ferent volumes of laundry The LOAD CARGA button is used to set the required steam level MIN MED or MAX All Iron Aid programmes apart from the amp REFRESH VENTILACION pro gramme automatically recognise the re maining dampness in clothes When laundry is wet a drying cycle is activated first if required The programme chart shows the steam levels appropriate for the selected load under LOAD CARGA 1 Press the LOAD CARGA button re peatedly until the desired steam level MIN MED or MAX is shown in the display If the LOAD CARGA button is not pressed after an Iron Aid programme is selected the medium steam level MED is selected automatically If you select the REFRESH VENTILACION pro gramme MIN is selected automatically Oo a Fl algod n E Sint ticos a x Y Algod n AX Sint ticos AS Ventilaci n ii B3 Z n re Important If in doubt always select a lower steam level first until you have more experience with load vol um
32. rst few Iron Aid programmes at low steam levels and with a small number of garments that are as sim ilar as possible Later you can care fully start to vary the conditions of Iron Aid programmes to learn from experience how to get the best re sults from the volume of laundry loaded the quality of the textiles and the most suitable steam levels and Iron Aid programmes Please also note the accompanying Textile Guide overview of iron aidtm programmes electrolux 17 GB Programme LOAD Loading idein ZR Ton CARGA volume min Er MIN 1 2items COTTON Es ALGODON MED 3 4 items 19 3 40 10 MAX 5 items MIN 1 2 items SYNTHETICS SINT TICOS MED 3 4 items 21 3 30 10 MAX 5 items MIN 0 5 1kg amp COTTON i ALGODON MED 1 2kg 20 97 8 40 10 MAX 2 3kg MIN 0 2 0 5 kg A SYNTHETICS SINTETICOS MED 0 5 1 kg 21658 30 10 MAX 1 1 5kg MIN 1 pair of trousers amp x REFRESH VENTILACION MED 1 jacket 10 GES MAX 1 suit B All information provided on select exact programme times appear in the ing the steam level and correspond display once the machine has per ing load are suggestions only In formed wet dry recognition approx 2 some cases using a higher steam min level or smaller load may give better results The REFRESH VENTILACION programme is a gentle Iron Aid pro gramme for non washable textiles Any distortion to the shape of a gar ment which might
33. ted as household waste Instead it shall be handed over to the applicable col lection point for the recycling of electrical and electronic equipment By ensuring this product is dis posed of correctly you will help pre vent potential negative consequences for the environment and human health which could oth erwise be caused by inappropriate waste handling of this product For more detailed information about re cycling of this product please con tact your local city office your household waste disposal service or the shop where you purchased the product disposal electrolux 7 A Warning Remove mains plug from socket when you have no further use for the machine Cut off mains cable and dispose of together with plug Destroy loading door lock Children cannot then lock themselves in the machine and put their lives at risk 8 electrolux environmental tips Environmental tips e During the drying process laundry becomes fluffy and soft Fabric sof teners are not therefore needed when washing e Condensed water can be used for iron aid programmes after beeing fil tered e Your appliance will function most economically if you spin the laundry well before drying Example Consumption data de pending on spinning speed for 6kg of laundry dried using the amp COTTON M CUPBOARD AL GODON SECO ARMARIO pro gramme Pre draining Revolutions per minute Residual dampness in litres
34. tion Laundry becomes drier as you move from MIN to MAX 1 Press the DRYNESS GRADO DE SEC button repeatedly until the de sired dryness level MIN MED or MAX is shown in the display If an other programme has been select ed AUTO flashes in the display If wool or silk comes out of the machine too damp at the end ofa WOOL LANA or t SILK SEDA programme you can dry it again by restarting the ap propriate programme this time with the DRYNESS GRADO DE SEC function selected and dryness level MIN MED or MAX In the case of a drying cycle with relatively dry laundry the length of the programme cycle displayed at the be ginning is corrected after a while gt Extra Seco 3 Seco Armario Semiseco El Extra Seco Seco Armario Semiseco SE Lana Tiempo O uj Seda Grado de Secado Delicado Alarma Tiempo ve A e S AUTO MER Grado de Secado Caution Make sure that by select ing the DRYNESS GRADO DE SEC function you do not over dry your wool or silk DELICATE DELICADO e For especially gentle drying of sensitive fabrics with the care label and for temperature sensitive textiles e g acrylic viscose Programme is execut ed with reduced heat DELICATE DELICADO is only suitable for use with loads of up to 3kg 1 Press the DELICATE DELICADO button The DELIC
35. ts please first check whether you can remedy the problem yourself with the help of the op erating instructions section What to do If If you were not able to remedy the prob lem yourself please contact the Cus tomer Care Department or one of our Service partners In order to be able to assist you quickly we require the following information xav PNC XXX XXX XXX XX S No XXXXXXXX ce Model description Product number PNC Serial number S No for numbers see rating plate Type of fault Anyerror messages displayed by the appliance So that you have the necessary refer ence numbers from your appliance at hand we recommend that you write them in here Model description eeeeeeeemmHH uo M L L corp stand vane SIND M de www electrolux com www electrolux es 125 985 250 01 180806 01
36. ualified personnel If necessary please contact your lo cal Service Force Centre 42 electrolux guarantee customer service Guarantee Customer Service European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual for the period specified in the appli ance guarantee or otherwise by law If you move from one of these countries to another of the countries listed below the appliance guarantee will move with you subject to the following qual ifications e The appliance guarantee starts from the date you first purchased the appliance which will be evidenced by production of a valid pur chase document issued by the seller of the appliance e The appliance guarantee is for the same pe riod and to the same extent for labour and parts as exists in your new country of resi dence for this particular model or range of appliances e The appliance guarantee is personal to the original purchaser of the appliance and can not be transferred to another user e The appliance is installed and used in ac cordance with instructions issued by Elec trolux and is only used within the home i e is not used for commercial purposes e The appliance is installed in accordance with all relevant regulations in force within your new country of residence The provisions of this European Guarantee do not affect any of the rights granted to you by law Weitere Kundendienststel
37. utomatically followed by a anti crease phase which lasts around 30 minutes The drum rotates at intervals during this phase This keeps the laundry loose and free of creases It can be removed at any time during the anti crease phase The laundry should be taken out towards the end of the anti crease phase at the lat est to prevent creases from forming 1 Open door 2 Before removing the laundry remove fluff from the micro fine filter It is best to use a damp hand for this purpose See Cleaning and maintenance section 3 Remove laundry 4 Turn the programme knob to O OFF Important After each drying cycle Clean the micro fine filter and fine fil ter Drain the condensed water contain er See section Cleaning and mainte nance 5 Close door 28 electrolux cleaning and maintenance Cleaning and maintenance Cleaning lint filters To ensure that the appliance works per fectly the lint filters in the door and in front of the drum must be cleaned after every Iron Aid or drying cycle A Important Never operate the dryer without the lint filter or with a dam aged or blocked lint filter 1 Open the door 2 Use a damp hand to clean the lint fil ter which is built into the lower part of the loading aperture 3 Remove the lint filter from the door by pulling the grip upwards 4 Remove fluff from lint filter preferably using a damp hand for this purpose 5 Replace the filter
38. with foam rubber pads should not be dried in the appliance Fabric softeners or similar products should be used as specified by the fabric softener instructions Do not place heavily worn laundry items in the appliance Risk of fire Do not place laundry items with loose fillings e g cushions in the appliance Risk of fire Parts with rigid components e g door mats may cover the air holes Risk of fire Do not place such items in the appliance Do not overfill the appliance Risk of fire Observe max loading volume of 6 kg Ensure that explosive objects e g cigarette lighters spray cans etc do not enter the appliance with the laundry Risk of fire and or explo sion Items that have been soiled with substances such as cooking oil ac etone alcohol petrol kerosene spot removers turpentine waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the appliance Clean micro filter and fine filter after every drying or Iron Aid programme Never operate the appliance without fluff filters or with damaged or blocked fluff filters Risk of fire 6 electrolux safety Only fill the water reservoir with dis tilled water Do not use tap water or any additives The condensed water from this appliance s condensed wa ter container can also be used if it is filtered first e g with a coffee filter Clean the heat exchanger regularly With stacked washer an
39. y ironing after they come out of the machine Multi layered garments tend to lose their shape After an Iron Aid pro gramme there are no creases left in the gar ments The Iron Aid programme has the effect of smoothing gar ments Iron creases in again after the Iron Aid programme what to do if electrolux 37 Drying results unsatisfac tory When you press a button Err appears in the multi display Drying cycle ends shortly after programme starts ANTICREASE display illu minated Programme inactive CONTAINER display illu minated PROGRAMME TIME dis play changes erratically or stays unchanged for a long time Drying cycle lasts an unu sually long time Note After up to 5 hours the drying cycle ends au tomatically see End of drying cy cle Discoloration Wrong programme selected Lint filter blocked Heat exchanger blocked with fluff Incorrect amount of washing Ventilation slots in base area covered up Residue on inside surface of drum or drum paddles Laundry guard Additional func tions cannot be selected after a programme has started Too little laundry has been load ed for the selected programme or laundry that is too dry Condensed water container is full Programme time is corrected automatically depending on type and volume of laundry and level of dampness Fluff filter blocked Heat exchanger blocked with fluff DELICATE DELICADO

Download Pdf Manuals

image

Related Search

Related Contents

MT382-T1 Installation and maintenance manual    Service Manual MUL serie FWCA-SL  SX221B - Sunex® Tools  Dry Tech 1  Transmisor-receptor inalámbrico HSM2HOST bidireccional  AB 10 BC 12  Poulan 140603 Lawn Mower Accessory User Manual  Sika Chapdur  Samsung RSH7PNPN Uživatelská přiručka  

Copyright © All rights reserved.
Failed to retrieve file