Electrolux EI23CS65KS Installation Instructions
Contents
1. Place end of water supply line into sink or bucket Turn ON water supply and flush supply line until Water is clear Turn OFF water supply at shutoff valve Remove plastic cap from water valve inlet and discard cap If you use copper tubing Slide brass compression nut then ferrule sleeve onto water supply line Push water supply line into water valve inlet as far as it will go 1 4 inch 6 4 mm Slide ferrule sleeve into valve inlet and finger tighten compression nut ore eee eee SE aan steel este onto valve Tighten another half turn with a wrench A ua soun tumon iowa DO NOT overtighten See Figure 1 1 moving refrigerator out for cleanin If you use stainless steel tubing The nut and fer rule are already assembled on the tubing Slide compression nut onto valve inlet and finger tighten compression nut onto valve Tighten another half turn with a wrench DO NOT overtighten See Figure 2 low With steel clamp and screw secure water supply line copper tubing only to rear panel of refrigerator as shown 6 Coil excess water supply line copper tubing only about 2 turns behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface Turn ON water supply at shutoff valve and tighten any connections that leak Reconnect refrigerator to electrical power source To turn ice maker on lower wire signal arm side mounted or set the ice maker s On Off power switch to t2. ONo water leaks present at all connections recheck in 24 hours Leveling Olce Maker is turned ON Olce amp Water Dispenser operates correctly OF ront filter must be flush with filter housing some models ORefrigerator is level side to side and tilted 1 4 inch 6 mm front to back OToe grille is properly attached to refrigerator OCabinet is setting solid on all corners Final Checks Electrical Power OShipping material removed OFresh Food and Freezer temperatures set OCrisper Humidity controls set ORegistration Card sent in OHouse power turned on ORefrigerator plugged in P N 241868803
3. toe grille on the lower front of your refriger ator Sufficient air circulation is essential for proper operation 2 toe grille to cabinet 3 Fasten top clips to cabinet 4 Close the doors On the left and the right side pull outward and then upward on the toe grille until the triangle tab is resting on the top edge of the hinge and the edge clip snaps into the hinge pocket on the back of the hinge To remove toe grille 1 With both doors closed unfasten right and left side clips of toe grille from bottom hinge groove 2 Open both doors Press firmly on top of toe grille until top of toe grille pops off 3 Pull toe grille outward towards your body and off of lower hinges NOTE Level the unit with the adjustable rollers before leveling the doors To level the doors using the adjustable lower hinge some models 1 Before leveling either door remove set screw that locks door height into position The door cannot be adjusted without set screw removed 2 Ifthe refrigerator door is lower than the freezer door raise the refrigerator door by turn ing the adjustment screw counterclockwise using a 1sinch wrench See illustration 3 If the freezer door is lower than the refrigerator door raise the freezer door by turning 4 the adjustment screw counterclockwise using a 46inch wrench See illustration After leveling verify door stop contacts lower hinge and top of doo
4. E Electrolux installation Instructions for Side By Side Refrigerator Z N WARNING To avoid electric shock which can cause death or severe personal injury refrigerator to an electrical power source until you have completed S Tools Necessary amp N 5 ve do not connect your ep 3 of these instructions NOTE These installation instructions are OR OR provided only as a possible customer N auae YO se rea option Electrolux recommends that bhilips Head Wrench Set D renen A enon VOU USE a service or kitchen contracting professional to install your refrigerator 1 Prepare The Installation Site Your refrigerator is designed to be part of a built in kitchen cabinet system Be sure to coordinate site preparation and 3 NOTE installation with your kitchen contractor Include these minimum guidelines in your site preparation Information about cabinetry construction for Electrolux products is available for e Choose a place near a grounded electrical outlet O77_AQB e Do not use an extension cord or an adapter plug contractors Call 1 877 435 3287 aa ale sunlight and close proximity to a range ishwasher or other heat source Floor should be level and able to support a fully loaded A CAUTION refrigerator The refrigerator s Ice amp Water Dispenser requires water supply access Room temperatures below 55 F Plan for easy access to counter tops when removing food 13 C or above 110 ain For complete access to
5. drawers and freezer baskets will impair cooling abilit doors must be able to fully open tefrigerator s compressor Allow the following clearances for ease of installation proper air circulation and plumbing and electrical connections Sides amp Top 3 8 inch Rear 1 inch 2 Transport Unpackaged Refrigerator To Site By now you have already removed your refrigerator s shipping carton You ma still need to use a hand truck to move it through close spaces or entrances If the refrigerator is larger than an entrance consider two options e Remove the entrance door if one exists e Remove the refrigerator doors see how in your Use amp Care Guide When using a hand truck e Load refrigerator from side of cabinet only Do not run retaining straps over handles Do not overtighten retaining straps Never use refrigerator handles to move the refrigerator Remove tape from doors only after unit is in place Shifting the refrigerator from side to side may damage flooring 3 Connect Water Supply Before Installing The Water Supply Line You Will Need Basic Tools adjustable wrench flat blade screwdriver A WARNING and Phillips screwdriver Access to a household cold water line with water To avoid electric shock which can pressure between 30 and 100 psi cause death or severe personal in A water supply line made of 1 4 inch 6mm OD copper jury disconnect the refrigerator from or stainless steel tubing To de
6. frigerator s power cord plugged in Is the refrigerator connected to the household water supply If you had to remove the refrigerator and freezer doors did you reattach water and power connectors at the door hinges See the Use amp Care Guide for detailed instructions on removing and replacing doors Is the ice maker power switch turned On Other possibilities to check e Is the power to the receptacle turned on e Is the water filter above the fresh food compartment fully seated see Use amp Care Guide for details If you still have operation problems after checking these suggestions please see the Solutions To Common Problems section in your Use amp Care Guide 8 What s Next Congratulations You are ready to begin enjoying your new Electrolux refrigerator To become aware of important safety instructions and learn how to operate your refrigerator please read the entire Use amp Care Guide You may want to start with the Normal Operating Sights amp Sounds section of the Guide to learn more about what to expect during typical operation Please register your product You can register online at www electroluxusa com or you can simply send in the Registration Card And thank you for choosing Electrolux 9 M Installation Checkoff List Doors Ice Maker OHandles are secure and tight OHouse water supply connected to ODoor seals completely to cabinet on all sides refrigerator OF reezer door is level across the top
7. he position rear mounted amp NOTE Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator Depending on your local state building codes Electrolux recommends for homes with existing valves its Smart Choice water line kit 5305513409 with a 6 ft Stainless Steel Water s4 and for homes without an existing valve Electrolux recommends its Smart Choice water line kit 5305510264 with a 20 ft Copper Water Line with self tapping saddle valve Please refer to www frigidaire com store for more information A Place In Permanent Position If possible use a hand truck to position the refrigerator directly in front of its cabinet enclosure A Cc AUTION Be careful not to move the refrigerator beyond its water supply copper tubing connections Plug in the power cord and push the refrigerator straight back into place mA IMPORTANT If you are installing your refrigerator without connecting it to a water supply make sure the ice maker s power switch is turned Off see the Use amp Care Guide for more details 5 Level Refrigerator amp Adjust Doors if necessary To install toe grille 1 Open both doors Slide left and right sides of toe grille over lower hinges of refrigerator While pushing toe grille firmly against cabinet fasten bottom clips of e Shifting the refrigerator from side to side may damage flooring e Do not block the
8. r does not contact upper hinge through full movement of door from fully closed to anus neckey boo Sup fully open om ee Replace the toe grille by fitting it into place This document should only be removed by customer after installation 6 Remove Internal Shipping Materials Electrolux uses packing foam and tape to secure the internal parts of your refrigerator for shipping Once the refrigerator is in position you can remove this material 1 FOAM BLOCK SHELF SPACER WITH TOE GRILL 1 PIECE OF TAPE p 1 PIECE OF TAPE 4 PIECES OF TAPE 4 PIECES OF TAPE 1 BOX OF DOOR BINS 3 PIECES OF TAPE AND DAIRY COMPARTMENT 4 PIECES OF TAPE 1 PIECE OF TAPE 3 PIECES OF TAPE 2 PIECES OF TAPE 1 BOX OF DOOR HANDLES 5 PIECES OF TAPE AND 2 PIECES OF TAPE 12 PIECES OF TAPE AU 7 PIECES OF TAPE 4 PIECES OF TAPE 2 PIECES OF TAPE 2 FOAM BLOCKS 2 PIECES OF TAPE 6 PIECES OF TAPE 1 FOAM BLOCK Location of these materials may vary depending on your model Ll Problems Try These Suggestions Operation problems are possible if any of the installation tasks are not completed Here is a list of things to check for Is the re
9. termine the length of electrical power before connecting a tubing needed measure the distance from the ice maker Water supply line to the refrigerator inlet valve at the back of the refrigerator to your cold water pipe Then add A CAUTION approximately 7 feet 2 1 meters so the refrigerator Tg Avoid Property Damage can be moved out for eC Stainl Steel braided tubing i ded cleaning as shown for he water supply line Water supply ubing made of i A shutoff valve to connect inch 6 mm plastic is not recommended to be used the water supply line to your Plastic tubing greatly increases the potential for water household water system DO leaks and the manufacturer will not be responsible for NOT use a self piercing type any damage if plastic tubing is used for the supply line shutoff valve DO NOT install water supply tubing in areas where tem A compression nut peratures fall below freezing and ferrule sleeve for Do not reuse compression fitting or use thread seal tape connecting a copper water Chemicals from a malfunctioning softener can damage the supply line to the ice maker ice maker If the ice maker is connected to soft water en inlet valve sure that the softener is maintained and working properly Not satisfied with the installation of your refrigerator gt Please contact the store where you purchased it To Connect Water Supply Line To Ice Maker Inlet Valve Disconnect refrigerator from electric power source
Download Pdf Manuals
Related Search