Electrolux BUILT-IN EDW7505HPS User's Manual
Contents
1. 2 Move dishwasher to front of installation area 3 Loosen the rear leveling legs by turning counterclockwise Refer to chart for number of turns Dishwasher Anchoring 4 Install the Cabinet Seal Kit Instructions included in Kit 5 Choose one of the methods of attachment below to secure unit holes need to be pre drilled using a 5 drill bit regardless of the option chosen a Side Mount Cabinet Clips Preferred Method of attachment b Top Mount Cabinet Clips to be used when Side Mount is not an available option CAUTION Use extreme care in mounting the dishwasher as to not scratch bump or otherwise damage the console or tub To install the Side Mounting Clips Depending on space allowed in cabinet the Side Mounting Clips can be installed with the holes for the screw up preferred method or down as shown in the illustrations below Use extreme caution when the clips are in the down position while installing the dishwasher NOTE Install Side Mount Brackets before unit is installed into the cabinet Insert screws into the front holes of the mounting clips only See image below Use if measures 34 to 35 To install using Top Mount Cabinet Clips Depending on the depth of cabinet the Top Mount Clip have a break off point that can be removed if necessary NOTE Install Top Mount Clips before unit is installed into the cabinet Screw clips firmly to top brace using screws provided in the literatu2. Note Locate the electrical supply and dishwashers electrical junction box on right underside of unit behind kickplate assembly See Figure 4 Determine where you will connect to hot water supply Review Figure 4 and note the location of water inlet valve Determine where you will connect the drain hose 3 Cut access holes for the Electrical Water and Drain hoses in the shaded areas as shown in Figure 2 4 The dishwasher operates on a 120 volt 60 Hz electrical supply Provide a separate circuit with a fuse or circuit breaker rated for at least 15 amps 20 amps if connected with disposer but not more than 20 amps 5 Pull electrical cable through hole into installation area 6 Be sure water inlet valve is protected from freezing If valve freezes and ruptures flooding may occur 7 Determine amount of tubing needed to connect hot water supply to the unit s water inlet valve Extra hose length is necessary High pressure and high temperature Stainless Flexible hose with a minimum inner diameter of 1 4 may be used A shut off valve installed outside dishwasher cabinet is best 8 Route water supply line into installation area 9 Stand dishwasher back upright for further installation IMPORTANT Incoming hot water temperature should be at least 120 F 49 C Water pressure should be between 20 90 psi Brass Elbow Electrical Line Not Included Water Line No
3. e Wrench Hex end e Wrenches 2 Adjustable for copper tubing or 2 Pipe wrenches for iron pipe plumbing Parts You Will Need Not Included e Drain Hose Clamp 1 Diameter e Brass Elbow 90 with a 7 s National Pipe Thread e Conduit Connector UL Listed e Wire Nuts three 3 for 12 14 gauge wire UL Listed i If required e Y Branch Tailpiece and Connector Kit See Step 4 e Air Gap Kit See Step 4 All the parts can be found at local hardware electrical and plumbing supply stores A WARNING Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation Failure to follow this warning could result in death or serious injury 2 Installation Preparation NOTE Put unit on its back being careful not to pinch the Water Drain Hose 1 Remove two 2 screws at front of the kickplate assembly using a 2 Phillips screw driver 2 Tiltand pull forward to remove see figure 1 NOTE It is not necessary to remove the outer door for installation Toeplate Kickplate Figure Kickplate Assembly 3 Locate water inlet valve behind kickplate on bottom left underside of unit See Figure 4 The valve has a s NPT female fitting Remove Plug 4 Wrap 90 elbow not included with pipe thread tape or apply joint compound and thread it into water inlet valve When tightened elbow should point toward the left
4. screws for mounting the custom wooden panel to the handled with care Wear gloves to protect dishwasher i Figure 5a Figure 5b 4 Replace junction box cover 10 Check that the dishwasher is level from front to back by taking nstal latio L D I ag ram out the lower rack place level on the lower rack wheel support at the bottom of the tub See Figure 5b 11 Adjust levelers up or down until dishwasher is level Sink at Left 2 Drain Hose Hole Cabinet Attach Clip Holes need to be pre drilled using a 5 drill to secure unit Figure 7 Side hands Cabinet 2 If you connect to a sink drain entry will need to be above trap Seal A Y branch tailpiece and connector kit not included will make injury this method easier and includes all needed fittings and instructions See Figure 7 Tools you will need to install the Custom Wood Panel 32 Drill Bit 2 7 screws Optional A WARN NG INSTALLING THE CUSTOM PANEL Electric Shock Hazard Refer to the Figure 10 for instruction references If all connections are correct there are no leaks 1 Fit the handle onto the panel according to the manufacturer s and unit runs properly replace the kickplate instructions NOTE A handle should be used rather than a assembly before placing unit into operation knob A knob does not provide enough grip Failure to follow this warning may result in i Figure 5c Figure 5d Ta T
5. To prevent bending of bracket or breaking of valve avoid overtightening See Figure 4 Cabinet Preparation As a precaution it is recommended but not required that the cabinets enclosing all sides of the dishwasher including the underside of the countertop be sealed with an oil based paint or moisture proof polyurethane to prevent possible steam moisture damage Roughing In 3 A WARNING Electric Shock Hazard Observe all local codes and ordinances for electrical and plumbing connections All electrical and plumbing work should be performed by qualified persons Failure to follow this warning could result in death or serious injury 1 Make sure your location has the correct drain water and electrical outlets to make the connections Do not install unit under a cooktop range Damage to tub or other components will occur Electrical water and drainines must be confined to shadedrea Preferred drain areas 35 max height for f 4 Standard cabineticutout e 13 4 A6 min clearance 13 4 312 min to required from unit to 4h max 1 4 underside of countertbp 174 gt N NE 24 Figure 2 Front Left Right 497k gt 2244 Door in 90 open position 3374 Adjustakd to 344 etl Height only adjustable to 34 max when installed in 35tnax standard cabineticutout T W er inlet and power A location middle bottom rear Figure 3 DIMENSIONS DO
6. 2 The two short screws go into the back of the panel 14 7 from the upper edge of the panel and from the edge of the Right Side panel Insert the short screws into the panel leaving of Installation space between the screw head and the panel ae check these items 3 Hook the panel screws into the rectangular openings of the metal panel on the dishwasher door 13 Open and close dishwasher door slowly Ensure that there is clearance to the console Adjust accordingly until door opens and closes freely Failure to follow this warning could result in electric shock Water Line Figure 6b Electrical Line Finishing the Water and 6 Q Water and drain lines have no kinks and move freely 4 Open the door and use the six screws supplied to secure the P behind the dishwasher panel to the door Electrical Connection check these items a maere Water and electrical lines are straight out in front of the Q Joints are free of leaks NOTE The door panel cannot exceed 12 pounds dishwasher Q Wiring connections to junction box are tight all access G Allfourleg levelers are positioned properly 3 If you connect to a sink trap local codes may require you to panels are secured back in place A CAUTI O N _ install an air gap kit not included The drain hose will be routed L Replace kickplate See Figure 1 a 23 5 0 a Cabinet Seals are positioned on the sides and top of the from dishwasher to air gap i
7. Dishwasher Installation Instructions Printed in U S A 154744001 12 08 INSTALLER Leave nstallation Instructions with owner OWNER Read your dishwasher Use and Care Guide It contains important safety information for operating this appliance It also has many suggestions for getting the best results from your dishwasher Before You Begin Read all instructions before installing dishwasher For your safety please read and observe all safety instructions This guide will help you anticipate drain water and electrical connections and help you select the best location for the A WARNING Tip Over Hazard Do not use dishwasher until completely installed Do not push down on open door Failure to follow this warning can result in serious injury A WARNING Cut Hazard To prevent serious injury from sharp edges wear work gloves when handling unpacking or disassembling unit Installation Tips 1 Tools and Materials Needed for Installation Not Included e Drill Electric Drill Bit 1 7 Driver Socket r he e Flaring Tool Tube Cutter for copper tubing e Flashlight e Level e Pipe Joint Compound for iron pipe plumbing or Pipe Thread Tape for sealing threads e Pliers e Safety Glasses Saw Keyhole or 11 7 to 2 Hole Cutters e Screw Drivers Slotted and 2 Phillips magnetic tip preferred e Tape Electrical or Duct e Tape Measuring e Wire Stripper or Utility Knife
8. NOT INCLUDE INSULATION IMPORTANT For proper operation and appearance of unit cabinet opening should have dimensions as shown in Figure 2 If unit is to be placed in a corner there must be at least a 2 inch side clearance to open door 2 Floor should be flat and free of any obstruction IMPORTANT Drain water and electrical lines should be roughed in before going any further A WARNING Electric Shock Hazard Electrical water and drain lines must be confined to shaded areas in Figure 2 Electric conductors water and drain could be damaged Failure to follow these instructions could result in fire or electric shock NOTE If dishwasher is installed at end of a cabinet sides and back must be fully enclosed NOTE Cabinet Seal Kit Kit 154662101 This kit provides a seal between the unit and cabinets once installation is complete The Installation Instructions are located in the Kit A WARNING Weight Keep children away from the front of the dishwasher so that they are not accidentally hit by the door during loading or unloading or if door should unexpectedly open The weight of the door can cause injury Connections For Electrical 4 Water and Drain Locating the Connections 1 Review dimensions in Figure 2 to locate dishwashers drain water and electrical connections 2 All utilities must be routed in shaded area in the Figure 2 IMPORTANT Disconnect power before starting installation
9. and Silverware ay 2 emcee eee ee eee A WARN l N G Cut for 5 8 connection Baskets ia 2 Pilot drill holes a a ah 1s dia x14 max depth 23 Water Line 1 Flush water line before connecting it to water inlet valve to M 9 prevent early clogging of filter screen Place a bunched towel C hecki n g the nstal lati on ae 6 Pilot drill holes fs Figure 9 a Cut for 3 4 connection over end of line to prevent splashing Open water supply valve for a few seconds and let water drain into a pan Turn off water supply at shut off valve 2 Route water line to water inlet valve as shown in Figure 4 Ye dia x3 max depth Note All handle Oper ate the machine thr ough at hk 2311 gt attachment x screws must be least one fill and pump ou t Optional holes for 1 2 7 screws flush recessed checking the f ollowing items which slip into rectangular openings of below panel metal ae to help locate custom door surface Handle Alternate XO OnEDW7505HSS and EDW7505HPS press and hold panel tor other outside screw attachment not included Electric Shock Hazard 3 While firmly pulling water supply line into 90 elbow tightly Grounding Instructions connect water supply to water inlet valve Supply line must be The dishwasher must be connected to a grounded metal free of kinks scales chips and lubricants permanent wiring system or an equipment grounding conductor must be run with the circuit conduct
10. nlet as shown in Figure 8 An air p Yz dishwasher l Q Drain hose is assembled to Drain Hose Connector Property Damage gap kit is available from a plumbing supply store If the drain F 7 Do not solder within 6 of the water inlet valve Damage to LI Cabinet Attachment Clips are attached to the cabinet on hose is installed through the floor an air gap is necessary J All packing materials and conn literature have Thickness 3 4 gt yal the plastic parts in the valve may occur both corners on top of the dishwasher 4 Ifyou connect to a disposer the large end of drain hose will fit been removed from inside unit Weight 12 Ibs max raz Use care that no sealer dirt or other objects enter the valve QO Remove protective film before replacing toe and kickplate Figure 9 a The knock out plug must be removed from L Dishwasher is level and securely fastened including handle 1315 2 Damage to the filter screen may occur then replace Toe and Kickplate Note When replacing inside disposer inlet before making the final fit to drain LI Open and close door to make sure it does not hit 13 1A Tp Be sure the dishwasher is placed where the water inlet Toe and Kickplate hand tighten screws hose See Figure 9 b surrounding cabinet or countertop l valve will be kept from freezing If the valve freezes it may Q Make sure that all wire ties are removed from the Adjustable rupture and flooding may occur Rack Assembly Versa Tray Utility Tray
11. ors and 4 Turn on water supply and check for leaks connected to the appliance s equipment grounding terminal i E Drain SANTIZE touchpad for 8 seconds before first use or lead It is the consumer s responsibility to contact a Through i gs qualified installer to make sure the electrical installation ae ial Q Atfirst fill approximately 2 minutes make sure water Figure 10 Electrical Supply conforms with the National Electrical Code and local codes pe e completely covers filter surface 1 Remove junction box cover and pull house wiring into junction and ordinances l ies Q At pump out pump out is either when the cycle is box See Figures Below Do not connect the dishwasher to the power supply until the completed or canceled refer to the Use and Care Manual ADJUSTING THE DOOR SPRINGS appliance is permanently grounded 2 Usea UL listed conduit connector not included at box to for Starl Cancel make sure all water is pumped out stabilize wiring 3 Connect incoming black lead to dishwasher s black lead P ae i Joining aluminum building wire to stranded copper wire incoming white lead to dishwasher s white lead and incoming should be done by a qualified electrician using materials green lead to dishwasher s green lead with wire nuts See recognized by UL and local codes Grounding Instruction Warning Wire nuts must be tight All wiring connections must be enclosed in the junction box This unit has coppe
12. r lead wires Before you push the dishwasher into the cabinet opening test the door to make sure it stays in place at any angle If it tends to fall down adjust the tension of the door springs on the sides of the 2 Drain Hose Hole machine by moving them one hole farther back If the door moves Figure 9 b to close adjust the tension of the door springs on the side of the machine by moving them one hole forward Sink at Right Check water connections again for leaks Do not use an extension cord Such use can result in fire electrical shock or other personal injury The drain hose loop must be at least 32 high from the floor Failure to follow these instructions could result in death or to insure proper drainage serious injury
13. re pack See image below 6 If levelers need to be removed make sure that the floor is free of all 5 If the cabinet wall is wood sand edges of hole until smooth and obstructions n IS h i ng the D ral n rounded If cabinet wall is metal cover all sharp edges with C ustom Wood Panel 1 0 7 Carefully place dishwasher inside cabinet area such that is electrical or duct tape to avoid cutting drain hose centered in opening Use caution when moving dishwasher to Green Wire Co n necti on 6 Move unit back in place while routing drain hose through access O pti ona I prevent damage to cabinet dishwasher and floor to Green Wire hole Use caution to prevent damage to the dishwasher floor and 8 Front of door needs to be even with the front of adjoining cabinets Ground 1 Review Figures 7 8 and 9 to see the different ways to connect cabinets IMPORTANT Make sure there are no sharp bends Front levelers should allow 5 16 below underside of countertop dishwasher to drain system Choose method that best suits or kinks that might restrict drain flow to top of console your need 7 Secure drain hose to sink drain disposer or separate trap with a A WAR Ni i N G 9 Check that dishwasher is level from side to side by placing a level clamp IMPORTANT Be careful not to overtighten clamp or Weicht against the top front section of the tub See Figure 5a you may damage end of hose Do not connect hose to elg jancion horizon
14. t Included Figure 4 A CAUTION Property Damage Do not use the furnished drain hose or a rubber garden hose for the water supply line Either of these hoses can burst Flooding may occur and cause property damage Drain Hose Connector End Storage Location NOTE Pull the hose from End Storage Location side See images below to connect the Drain Hose 1 Take drain Hose out of dishwasher and find the end that doesn t have the black rubber material 2 Use only the spring clamp that is provided in the accessory kit place spring clamp over one of the hoses See Image Below Hose Attached To Dishwasher Plastic End Of Hose Hose Shipped Inside Dishwasher 3 Take the plastic side of the drain hose and insert it into the hose that is already attached to the dishwasher make sure hose ends are flush against each other See image below 4 Secure the spring clamp 1 8 from large end of black hose to the plastic side that was inserted for best sealing results See Image Below Plastic Ends of Hoses Flush Hose Attached to Dishwasher Tighten Spring Clamp Leveling and Securing Dishwasher within Cabinets 5 1 Measure height of cabinet opening from underside of countertop to floor Check chart for height opening and suggested adjustment Leg Leveler Adjustment Chart Cabinet Opening Adjust Levelers 34 86 4cm 341 8 86 7cm 345 16 87 2cm 341 2 87 6cm
15. tal pipe between sink drain and disposer Keep children away from the front of the dishwasher so that they are not accidentally hit by the door during loading or unloading or if door should unexpectedly open The weight of the door can cause injury A CAUTION Screws To prevent the possibility of damage to dishwasher replace factory installed outer door screws with factory supplied wood panel screws Box 8 Be sure unit does not rest on drain hose It should be free of electrical components and door springs Do not cut corrugated drain hose Pull excess through cabinet and place under sink Make sure hose does not come in contact with any sharp edges White Wire Junction Black Wire to White Wire Box Cover to Black Wire Neutral Figure 6a Hot A WARNING Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation Failure to follow this warning could result in death or serious injury The EDW7505HSS amp EDW7505HPS can be installed with a fully integrated buyer supplied custom door panel CAUTI O Ni The custom panel should be 1 2 to 3 4 19mm thick 12 Screw mounting brackets firmly to cabinet using screws provided in literature packet See Image Below Ne The drain hose loop must be at least 32 high from the floor Cut Hazard penis ees ean fo insure proper drainage Metal color panels are sharp and should be Six 1
Download Pdf Manuals
Related Search