Electrolux EI32AF80QS Owner's Guide
Contents
1. The audible alarm can be turned off by pressing the ALARM OFF key Stuck Key Alarm The stuck key alarm will sound if the control reads a keypress for longer than 30 seconds The audible alarm will sound and will be limited to one minute and will stop automatically The display will alternate between E7 and 10 F 23 C at 2 second intervals The control will then enter a mode that runs the unit in a manner that maintains the factory set cabinet temperature until the condition is resolved The audible alarm can be turned off by pressing the ALARM OFF key Sabbath Mode The Sabbath Mode is a feature that disables portions of the appliance and its controls in accordance with the observance of the weekly Sabbath and religious holidays within the Orthodox Jewish community To initiate or cancel Sabbath Mode press the CONTROL LOCK and TEMP MODE keys at the same time and hold for 3 seconds The display will now show Sb and the confirmation tone will sound When AC power is cycled while the control is in Sabbath mode the control enters into Sabbath mode automatically Sb will again be displayed While in Sabbath Mode the display will show Sb for one second if any key is pressed In the interest of food safety only the HIGH TEMP Alarm remains active and takes precedence over other Sabbath Mode features For further assistance guidelines for proper usage and a complete list of models with the Sabbath feature p2. Electrolux Major Appliances North America a division of Electrolux Home Products Inc In Canada your appliance is warranted by Electrolux Canada Corp Electrolux authorizes no person to change or add to any obligations under this warranty Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company Product features or specifications as described or illustrated are subject to change without notice No Oi e go BU USA Canada 1 877 485 3287 1 800 265 8352 Electrolux Major Appliances North America Electrolux Canada Corp 10200 David Taylor Drive 5855 Terry Fox Way Charlotte NC 28262 Mississauga Ontario Canada L5V 3E4 www electrolux store com
3. The IQ Touch Electronic Control is located inside the appliance Temperature is factory preset to provide satisfactory food storage temperatures However the temperature control is adjustable to provide a range of temperatures for your personal satisfaction Hinge Plate e Hier press amp hold sue U 2 air tem alarm control filter mode off lock Ddoorajar Opowerfal replace air filter To adjust the temperature setting press the UP key for warmer temperature and DOWN key for colder temperature on the control panel Allow several hours for the temperature to stabilize between adjustments The unit can be adjusted between 10 F 23 C and 10 F 12 C By pressing the TEMP MODE key the temperature display will toggle between F to C To turn the appliance OFF press the UP key until the warmest temperature setting of 10 F 12 C show in the display Then press the UP key 3 times within 3 seconds to turn the unit OFF The display will then scroll OFF across the display To turn the unit back ON press the DOWN key 3 times within 3 seconds The control will then display 10 F 12 C and may be adjusted to the desired temperature 10 Electronic Control amp Alarms IQ Touch Electronic Control Features Replace Air Filter When the REPLACE AIR FILTER LED is illuminated yellow the air filter needs to be replaced The control will signal for air filter replacemen
4. an odd flavor These first cubes should be discarded until the cubes produced are free of discoloration and taste Turning Your Ice Maker Off To stop the ice maker lift the wire signal arm until it clicks and locks in the up or OFF position The ice maker also turns off automatically when the ice container is full If your model has an adjustable freezer shelf place the shelf in the lower position so that the wire signal arm will hit the ice when the container is full Ice Maker Tips e If the ice maker will be turned off for a long period of time turn the water supply valve to the closed position e Ice cubes stored too long may develop an odd flavor Empty the ice container and ensure that the wire signal arm is in its down or ON position The ice maker will then produce more ice e Occasionally shake the ice container to keep ice separated e Keep the wire signal arm in its up or OFF position until the freezer is connected to the water supply or whenever the water supply is turned off e The following sounds are normal when the ice maker is operating e Motor running Ice loosening from tray e Ice dropping into ice container Running water e Water valve opening or closing Ice Service 15 Leveling Bracket Ice Container mA IMPORTANT Your ice maker is shipped with the wire signal arm in the ON position To ensure proper function of your ice maker hook up water supply
5. immediately or turn ice maker OFF by lifting the wire signal arm until it clicks and locks in the UP position Check the leveling bracket on the ice maker to ensure the ice maker is level If the gap between the freezer wall and the ice maker is the same at top and bottom then ice maker is level If the ice maker is not level loosen the screw and slide the bracket to the correct position to make it level Retighten the screw You will need a socket wrench for this task CAUTION e DO NOT place the ice container in dishwasher e Wash the ice container in warm water with mild detergent Rinse well and dry e Stop the ice maker when cleaning the freezer and during vacations 16 Storage Components Luxury Design Glass Shelves Multi position adjustable slide out glass shelves can be moved to any position for larger or smaller packages The shipping spacers that stabilize the shelves for shipping may be removed and discarded To Adjust The Shelves e Lift front edge up e Pull shelf out e Replace the shelf by inserting the hooks at rear of the shelf into the wall bracket Lower the shelf into the desired slots and lock into position Mid Level Baskets This model is equipped with two mid level baskets for convenient storage of small items Tall Lower Basket The tall lower basket is ideal for large items or items that do not store well on the shelves To remove the Mid Le
6. power N CAUTION e When moving the appliance pull straight out Do not shift the unit from side to side as this may tear or gouge the floor covering e Damp objects stick to cold metal surfaces Do not touch interior metal surfaces with wet or damp hands N CAUTION e Turning the temperature control to OFF See IQ Touch Electronic Control turns off the compressor but does not disconnect electrical power to the LED lights or other electrical components Unplug the unit or switch the breaker that supplies power to the unit to the off position e Do not use razor blades or other sharp instruments which can scratch the appliance surface when removing adhesive labels Any glue left from tape or labels can be removed with a mixture of warm water and mild detergent or touch the glue residue with the sticky side of tape you have already removed Do not remove the serial plate NOTE e Do Not use abrasive cleaners such as window sprays scouring cleansers flammable fluids cleaning waxes concentrated detergents bleaches or cleansers containing petroleum products on plastic parts interior doors gaskets or cabinet liners Do not use paper towels scouring pads or other abrasive materials Care amp Cleaning 19 e Never use metallic scouring pads brushes abrasive cleaners or strong alkaline solutions on any surface e Do not wash any removable parts in a dishwasher e Always unplug the electrical power Car
7. FQ ricci EN FREEZER USE AND CARE GUIDE FR CONG LATEUR GUIDE D UTILISATION ET D ENTRETIEN ES CONGELADOR GUIA DE USO Y CUIDADO A01061301 August 2014 2 Finding Information Please read and save this guide Thank you for choosing Electrolux our new premium brand in home appliances This Use amp Care Guide is part of our commitment to customer satisfaction and product quality throughout the service life of your new appliance Keep a record for quick reference Purchase date Electrolux model number Electrolux serial number NOTE Registering your product with Electrolux enhances our ability to serve you You can register online at www electroluxappliances com or by sending your Product Registration Card in the mail Questions For toll free telephone support in the U S and Canada 1 877 4ELECTROLUX 1 877 435 3287 For online support and product information visit http www electroluxappliances com Table of contents Finding Information ccccesseeesees 2 Installation Checklist 2 SAPS sisccescssciisensacesecesctvecsdessesciraveseasaseze 3 Feature Overview 5 Installation c cece ceeeeeeeeeeeeeeeseenseneeees 6 Installing Door Handle 7 LOVGIUNG 2 ccc cececcsteccescerecesssnccecsectnesesecesss 7 Door Removal amp Temperature Control 9 Electronic Control amp Alarms 10 Alarms amp Sab
8. LED AN WARNING Unplug the unit or switch the breaker that supplies power to the unit to the off position before changing an LED light 1 Unplug the electrical cord or switch OFF the power supply breaker 2 Push down on the LED cover and then pull away from the cabinet interior 3 From the inside of the LED cover remove the wire harness connector by pressing on the latch with a small flat bladed screwdriver Pull the wire harness connector out of the LED 4 Replace with a new LED and install in the reverse order Push on underside of connector to release latch Remove wire harness connection Water Supply 13 Water Supply ZN WARNING To avoid electric shock which can cause death or severe personal injury disconnect the appliance from electrical power before connecting a water supply line to the unit AN CAUTION To Avoid Property Damage e Copper or Stainless Steel braided tubing is recommended for the water supply line Water supply tubing made of inch plastic is not recommended to be used Plastic tubing greatly increases the potential for water leaks and the manufacturer will not be responsible for any damage if plastic tubing is used for the supply line e DO NOT install water supply tubing in areas where temperatures fall below freezing e Chemicals from a malfunctioning softener can damage the ice maker If the ice maker is connected to soft water ensu
9. ased as is are not covered by this warranty Food loss due to any refrigerator or freezer failures Products used in a commercial setting Service calls which do not involve malfunction or defects in materials or workmanship or for appliances not in ordinary household use or used other than in accordance with the provided instructions 8 Service calls to correct the installation of your appliance or to instruct you how to use your appliance 9 Expenses for making the appliance accessible for servicing such as removal of trim cupboards shelves etc which are not a part of the appliance when it is shipped from the factory 10 Service calls to repair or replace appliance light bulbs air filters water filters other consumables or knobs handles or other cosmetic parts 11 Pickup and delivery costs your appliance is designed to be repaired in the home 12 Surcharges including but not limited to any after hour weekend or holiday service calls tolls ferry trip charges or mileage expense for service calls to remote areas including the state of Alaska 13 Damages to the finish of appliance or home incurred during transportation or installation including but not limited to floors cabinets walls etc 14 Damages caused by services performed by unauthorized service companies use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies or external causes s
10. bath Mode s sss sssessssssn 11 Air Filter amp Luxury Design Lighting 12 Water SUPDIY sister 13 Connecting Water Supply 14 Ice Service ss 15 Storage Components 16 Storage Components amp Energy Saving Tips 17 Care amp Cleaning 18 Solutions To Common Problems 20 Warranty Information 23 Installation Checklist Doors Q Handles are secure and tight Q Door seals completely to cabinet on all sides Q Freezer door is level across top Leveling Q Freezer is level side to side and front to back Q Toe grille is properly attached to freezer Q Cabinet is set solid on all corners Electrical Power Q House power turned on Q Freezer plugged in Air Filter Q Air Filter is installed Final Checks Shipping material removed Freezer temperatures set Water turned on Registration card sent in Safety 3 Important safety instructions Safety Precautions Do not attempt to install or operate your unit until you have read the safety precautions in this manual Safety items throughout this manual are labeled with a Danger Warning or Caution based on the risk type Definitions This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death N DANGER DANGER indicates an imminently hazardous situation which if not avoided will resu
11. d and sub flush Allen set screw should be seated just below the surface of the end cap of handle end cap The end caps should be drawn tight to door with no gaps Toe Grille Removal To remove the toe grille use a Phillips head screwdriver and remove the two screws holding the toe grille to the cabinet Then pull the toe grille away from the unit Leveling e The freezer must have all bottom corners resting firmly on a solid floor e The floor must be strong enough to support a fully loaded freezer e Itis VERY IMPORTANT for your freezer to be level in order to function properly If the freezer is not leveled during installation the door may be misaligned and not close or seal properly causing cooling frost or moisture problems Ensure handle set screws are facing each other with doors closed Matching Refrigerator and Freezer Door Handle Installation Remove lt Screws 7 8 Leveling To Level The Freezer While unit is lying on its back note the location of the four 4 leg levelers installed at each corner These leg levelers will be used to level the freezer and to adjust the height Use a carpenter s level to level the freezer from front to back and side to side Adjust the plastic leveling feet in front 2 bubble higher so that the door closes easily when left halfway open NOTE Make sure to allow for the Trim and Leveling Kit if it is to be installed with th
12. e and cleaning tips Part Interior amp Door Liners e Door Gaskets e Drawers amp Bins Glass Shelves 0 Exterior amp e Handles Exterior amp e Handles z Stainless Steel Models Only Cleaning Agents Soap and water Baking soda and water Soap and water Soap and water Soap and water Glass cleaner Mild liquid sprays Soap and water Non abrasive glass cleaner Soap and water Ammonia Stainless steel cleaners Tips and Precautions Use 2 tbsp 25 g of baking soda in 1 qt 1 warm water Be sure to wring excess water out of sponge or cloth before cleaning around controls light bulb or any electrical part e Wipe gaskets with a clean soft cloth Use a soft cloth to clean drawer runners and tracks Do not wash any removable items bins drawers etc in dishwasher Allow glass to warm to room temperature before immersing in warm water Sudden temperature changes can cause glass breakage Do not use commercial household cleaners containing ammonia bleach or alcohol to clean handles Use a soft cloth to clean smooth handles Do not use a dry cloth to clean smooth doors Never use CHLORIDE or cleaners with bleach o clean stainless steel Clean stainless steel front and handles with non abrasive soapy water and a dishcloth Rinse with clean water and a soft cloth Wipe stubborn spots with an ammonia soaked paper towel and rinse Use a non abrasive stainless
13. e unit Plastic Leveling Feet Leveling Instructions For Matching Tall Refrigerator Tall Freezer Pair e Level door of first unit using all four levelers and slide unit into place Recheck for levelness and adjust if necessary e Measure distance from floor to bottom of door on first unit Adjust and level second unit so door height matches e Leg Level Adjustments One full turn of all four leg levelers will raise door 5 32 e Slide second unit into place leaving a minimum gap of 3 16 between units for door swing clearance e This last step may require at least one extraction of the second unit to properly align units in a built in application Leveling Door with Adjustable Hinge Use the lower hinge adjustment to fine tune the door height and for final cabinet spacing Use a 7 16 socket or wrench to adjust the screw at the bottom of the lower hinge Adjusting Doors For Matching Tall Refrigerator Tall Freezer Pair The doors may also be adjusted side to side with the slotted hinge for aligning the doors parallel to each other Loosen the two bolts with a 38 wrench and one screw with a Philips screwdriver Shift the doors until parallel then retighten the screws securely See illustration below Lower Hinge Adjustment For Leveling The Doors Of The Matching Tall Refrigerator Tall Freezer Pair To level the doors using the adjustable lower hinge some models 1 If the ref
14. ee telephone support in the U S and Canada 1 877 4ELECTROLUX 1 877 e Pressing the CONTROL LOCK and TEMP MODE keys to exit Sabbath Mode This is normal When the surrounding noise level is low you might hear the compressor running while it cools the interior This is normal Sound will level off or disappear as appliance continues to run This is normal Sound will level off or disappear as appliance continues to run This is normal Level the appliance Refer to the LEVELING section Ensure floor can adequately support the appliance Level the appliance by putting wood or metal shims under part of the appliance Re level appliance or move appliance slightly Refer to the LEVELING section This is normal See DOOR PROBLEMS Open the door less often Clean interior with sponge warm water and baking soda Replace air filter e Cover the food tightly 22 Solutions to Common Problems Concern Potential Cause Common Solution Door will not e Appliance is not level It This condition can force the cabinet close rocks on the floor when out of square and misalign the door it is moved slightly Refer to the LEVELING section e Floor is uneven or weak je Ensure floor can adequately support appliance Level the appliance by putting wood or metal shims under part of the appliance Lighting Problems Light bulb is noton j The LED or light bulb is Follow directions under the Lux
15. from the receptacle to prevent damaging the power cord To avoid electrical shock unplug the unit before cleaning and before replacing a light bulb or LED light Performance may be affected if the voltage varies by 10 or more Operating the appliance with insufficient power can damage the compressor Such damage is not covered under your warranty Do not plug the unit into an outlet controlled by a wall switch or pull cord to prevent the appliance from being turned off accidentally mA IMPORTANT To disconnect power to the unit unplug the unit or switch the breaker that supplies power to the unit to the off position Grounding type wall receptacle Do not under any circumstances cut remove or bypass the grounding prong Power cord with 3 prong grounded plug Feature Overview 5 Understanding features and terms Your Electrolux appliance is designed for optimal convenience and storage flexibility The illustration below is provided to assist you with and terminology NOTE Features may vary according to model familiarizing yourself with product features Ice Bin aaa Pure ouc Advantage les Make Electronic Air Filter Adjustable Two Liter Bins il nl tl Soft Freeze Bin wltall Bottle Retainer Condiment Shelf Adjustable Bottom Hinge Control Air Baffi id Luxury Design Glass Shelves Luxury Design LED Ramp up Lighting Mid Level Baske
16. ger and use more energy e Cover foods and wipe containers dry before placing them in the unit This cuts down on moisture build up inside the unit e Organize the appliance to reduce door openings Remove as many items as needed at one time and close the door as soon as possible 18 Care amp Cleaning Vacation And Moving Tips Short Vacations e Leave the unit operating during vacations of less than three weeks Long Vacations If the appliance will not be used for several months e Remove all food and unplug the power cord e Clean and dry the interior thoroughly e Leave the door open slightly blocking it open if necessary to prevent odor and mold growth Moving When moving the unit follow these guidelines to prevent damage e Disconnect the power cord plug from the wall outlet e Remove foods then defrost and clean the appliance e Secure all loose items such as base panel baskets and shelves by taping them securely in place to prevent damage e In the moving vehicle secure the unit in an upright position to prevent movement Also protect outside of the appliance with a blanket or similar item Care amp Cleaning Keep your unit clean to prevent odor build up Wipe up any spills immediately and clean at least twice a year Never use metallic scouring pads brushes abrasive cleaners or strong alkaline solutions on any surface Do not wash any removable parts in a dishwasher Always unplug the electrical
17. he temperature is as much as 30 F warmer compressor works to transfer heat warm than room temperature from inside the cabinet Solutions to Common Problems 21 Concern Potential Cause Common Solution LO is displayed e Control has been locked e Press the CONTROL LOCK key on control for 3 seconds to unlock E7 E8 EQ is displayed on control Sb is displayed e The control is in on control Sabbath Mode Sound amp Noise Louder sound levels whenever appliance is on Louder sound levels when compressor rattling noise Moisture forms on inside appliance walls Odor In Appliance Odors in appliance The control has registered an error code Modern appliances have increased storage capacity and more stable temperatures They require heavy duty compressors Appliance operates at higher pressures during the start of the ON cycle Metal parts undergo expansion and contraction as in hot water pi Refrigerant used to cool appliance is circulating throughout the system Appliance is not level It rocks on the floor when it is moved slightly Floor is uneven or weak Appliance is touching the wall Weather is hot and humid which increases internal rate of frost buildup Door is slightly open Door is kept open too long or is opened too frequently nterior needs to be cleaned Foods with strong odors are in the appliance e For toll fr
18. ishwasher or other heat sources e The appliance must be installed on a floor that is level and strong enough to support a fully loaded unit e Consider water supply availability for models equipped with an automatic ice maker NOTE The exterior walls of the unit may become quite warm as the compressor works to transfer heat from the inside Temperatures as much as 30 F warmer than room temperature can be expected Phillips Head or 2 Square Drive Head If your appliance is placed with the door hinge against a wall you may have to allow additional space so the door can be opened wider Freezer 10 mm Installing Door Handle Door Handle Mounting Instructions 1 Remove handle from carton and any other protective packaging 2 Position freezer handle end caps over upper and lower pre installed shoulder bolts A that are fastened into door ensuring the holes for the set screws are facing towards the outside of door if a single unit installation or the refrigerator door if installing the matching refrigerator 3 While holding handle firmly against door fasten upper and lower Allen set screws B with supplied Allen wrench 4 Repeat steps 2 and 3 to install refrigerator handle if installing the matching refrigerator Ensure the holes for the set screws are facing towards the refrigerator door NOTE All set screws should be tightene
19. leak Reconnect freezer to electrical power source 9 To turn ice maker on lower wire signal arm side mounted or set the ice maker s On Off power switch to the I position rear mounted Steel Clamp Brass Compression Nut Ferrule Sleeve 4 4 Copper water line Plastic Water Tubing to Ice Maker Water Valve Bracket Valve Inlet Water Valve gt ee N water line from household water supply Include enough tubing in loop to allow moving refrigerator out for cleaning Figure 1 Plastic water tubing to ice maker fill tube Stainless steel water line ater valve bracket 6 ft stainless steel water line from household water supply Figure 2 If your freezer has an automatic icemaker it will provide a sufficient supply of ice for normal use During the initial startup of your freezer however no ice will be produced during the first 24 hours of operation Automatic ice makers are also optional accessories that may be installed in some models at any time Call your local dealer for information Turning Your Ice Maker On After the plumbing connections have been completed the water supply valve must be opened Place the ice container under the ice maker pushing it as far back as possible Lower the wire signal arm to its down or ON position New plumbing connections may cause the first production of ice cubes to be discolored or have
20. lease visit the web at htto www star k org hold to reset press amp hold Electrolux Sh tem alarm control inode off jock O door ajar power fail Pure Advantage Air Filter Your new Pure Advantage air filter is located inside one of the 2 Liter Door Bins The air filter cover is located on the upper right side of the control box In general you should change the air filter with Part Number EAFCBF every 6 months to ensure optimal filtering of freezer odors The replacement air filter can be purchased on the Electrolux website http www electroluxappliances com or Call toll free in the U S and Canada 1 877 4ELECTROLUX 1 877 435 3287 Your electronic control is equipped with a Change Filter Indicator to remind you to change your filter See Replace Air Filter To Install Or Replace The Air Filter e Pull down on the front of the Pure Advantage air filter cover This releases the hinged bottom cover to drop open e Remove the old filter and discard it e Unpackage the new filter and place it inside the hinged bottom cover of the housing e Push the hinged bottom cover upward until the tab snaps into closed position Air Filter A Remove air filter 12 Air Filter amp Luxury Design Lighting Luxury Design Lighting The interior cabinet lighting features LED lights that gradually ramp up in intensity after the door is opened To replace an
21. lt in death or serious injury AN WARNING WARNING indicates a potentially hazardous situation which if not avoided could result in death or serious injury N CAUTION CAUTION indicates a potentially hazardous situation which if not avoided may result in minor or moderate injury mA IMPORTANT Indicates installation operation or maintenance information which is important but not hazard related General Safety AN WARNING Please read all safety instructions before using your new refrigerator e Do not store or use gasoline or other flammable liquids near this or any other appliance Read product labels for warnings regarding flammability and other hazards e Do not operate the appliance in the presence of explosive fumes e Avoid contact with any moving parts of the automatic ice maker e Remove all staples from the carton to avoid injury Staples can also damage finishes if they come in contact with other appliances or furniture Child Safety Packing Materials e Packing cartons covered with rugs bedspreads plastic sheets or stretch wrap may become airtight chambers and can quickly cause suffocation e Destroy or recycle the products carton plastic bags and any other exterior wrapping material immediately after the unit is unpacked Children should never play with these items Child Entrapment and Suffocation e These problems are not limited to the past Whether junked abandoned or te
22. ly Appliance has recently been disconnected for period of time e Use another circuit If you are unsure about the outlet have it checked by a certified technician e See Setting the IQ Touch Electronic Control section e Ensure plug is tightly pushed into outlet Check replace fuse with a 15 amp time delay fuse Reset circuit breaker Check house lights Call local Electric Company It s normal for the appliance to work harder under these conditions It takes 24 hours for the appliance to cool down completely Warm food will cause the appliance to run more until the desired temperature is reached Warm air entering the Freezer causes it to run more Open the door less often See DOOR PROBLEMS Set control to a warmer setting Allow several hours for the temperature to stabilize Clean gaskets See Care and Cleaning Chart Worn cracked or poorly fitting gaskets should e Temperature controlis e Set control to a warmer setting set too low Allow several hours for the temperature to stabilize e Set control to a colder setting Allow several hours for the temperature to stabilize Warm air entering the appliance causes it to run more Open the door less often See DOOR PROBLEMS Wait until the appliance has had a chance to reach its selected temperature Appliance requires 24 hours to cool down completely External surface e The external walls can befje This is normal while t
23. mporarily stored even for a few hours unattended appliances are dangerous Please take the precautions listed below Proper Disposal of Appliance We strongly encourage responsible appliance recycling disposal methods Check with your utility company or visit www energystar gov recycle for more information on recycling your old unit Before you recycle or dispose of your old appliance e Remove the doors e Leave the shelves and baskets in place so children may not easily climb inside e Have refrigerant and compressor oil removed by a qualified service technician 4 Safety Electrical information AN WARNING You must follow these guidelines to ensure that your appliance s safety mechanisms are operating correctly The unit must be plugged into its own dedicated 115 Volt GO Hz AC only non GFCl electric outlet The power cord of the appliance is equipped with a three prong grounding plug for your protection against electrical shock hazards It must be plugged directly into a properly grounded three prong receptacle The receptacle must be installed in accordance with local codes and ordinances Consult a qualified electrician Do not use an extension cord or adapter plug If the power cord is damaged it should be replaced by the manufacturer service technician or a qualified person Never unplug the appliance by pulling on the power cord Always grip the plug firmly and pull straight out
24. old Electrolux A SE air temp alarm control HI TEMP DURATION filter mode off lock Qdoorajar mpowerfal replace air filter Alarms There are 4 possible conditions that will cause the alarm tone to sound High Temp Alarm If the temperature inside the cabinet exceeds 23 F 5 C the HIGH TEMP LED will illuminate and after 1 hour the HIGH TEMP Alarm will sound and the cabinet temperature is shown in the display The LED and temperature alarm will remain active until the cabinet temperature is below 23 F 5 C The audible alarm can be turned off by pressing ALARM OFF key Alarms amp Sabbath Mode 11 A E mem H Electrolux so F d i Cidoorajar power fail replace air filter Door Ajar Alarm This alarm will sound to alert you that the door has been open for 5 minutes or more The DOOR AJAR LED will illuminate and the audible alarm will sound until the door is closed The audible alarm can be turned off by pressing the ALARM OFF key or by closing the door If the door is ajar for 15 minutes the interior light will turn off Temp Sensing Error Alarm The sensor alarm signals you that a problem exists with a temperature sensor The audible alarm will sound after one 1 hour and the display will alternate between E8 or E9 and 10 F 23 C at second intervals The control will then enter a mode that runs the appliance in a manner that maintains the factory set cabinet temperature
25. re that the softener is maintained and working properly m IMPORTANT Ensure that your water supply line connections comply with all local plumbing codes Before Installing The Water Supply Line You Will Need e Basic Tools adjustable wrench flat blade screwdriver and Phillips screwdriver e Access to a household cold water line with water pressure between 30 and 100 psi e Awater supply line made of 14 6 4 mm OD copper or stainless steel tubing To determine the length of tubing needed measure the distance from the ice maker inlet valve at the back of the freezer to your cold water pipe Then add approximately 7 feet 2 1 meters so the freezer can be moved out for cleaning as shown e A shutoff valve to connect the water supply line to your household water system DO NOT use a self piercing type shutoff valve e Acompression nut and ferrule sleeve for connecting a copper water supply line to the ice maker inlet valve 14 Connecting Water Supply Connecting Water Supply NOTE Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator Depending on your local state building codes Electrolux recommends for homes with existing valves its Smart Choice water line kit 5805513409 with a 6 ft Stainless Steel Water Line and for homes without an existing valve Electrolux recommends its Smart Choice water line kit 5805510264
26. rigerator door is lower than the freezer door raise the refrigerator door by turning the adjustment screw clockwise using a 7 16 socket wrench See illustration below 2 lf the freezer door is lower than the refrigerator door raise the freezer door by turning the adjustment screw clockwise using a 7 16 socket wrench See illustration below Slotted Hinge Adjustment Freezer Refrigerator Door Removal amp Temperature Control 9 Door Removal If door must be removed AN CAUTION Doors are heavy It is recommended to have two people remove or replace the door assembly from the cabinet e Unplug the unit or switch the breaker Hinge Cover that supplies power to the unit to the a off position i e Remove the plastic top hinge cover Hinge Bolts 2 e Hold the door in place while removing the top hinge from the cabinet 1 e Remove the two 38 hex head bolts from the top hinge with a 38 wrench or socket e Lift the door upwards and pull up and away from the cabinet until free of the bottom hinge pin mounted on the front of the cabinet e To replace the door reverse the above procedures and securely tighten all screws to prevent hinge slippage Setting The IQ Touch Electronic Control COOL DOWN PERIOD For safe food storage allow 4 hours for the appliance to cool down completely The unit will run continuously for the first several hours IQ TOUCH ELECTRONIC CONTROL
27. steel cleaner These cleaners can be purchased at most home improvement or major department stores Always follow manufacturer s instruction NOTE Always clean wipe and dry with grain to prevent scratching Wash the rest of the cabinet with warm water and mild liquid detergent Rinse well and wipe dry with a clean soft cloth Troubleshooting Guide 20 Solutions to Common Problems Before calling for service review this list It may save you time and expense This list includes common occurrences that are not the result of defective workmanship or materials in this appliance Concern Potential Cause Common Solution Appliance is plugged into a circuit that has a ground fault interrupt Temperature control set 10 ORF Appliance may not be plugged in or plug may be loose House fuse blown or tripped circuit breaker Power outage Room or outside weather is hot Appliance has recently been disconnected for a period of time Large amount of warm or hot food have been stored recently Door is opened too frequently or kept open too long Door may be slightly open Temperature control is set too low Appliance runs Appliance gaskets are dirty worn cracked or poorly fitted Interior temperature is Temperature control is set too warm Door is opened too frequently or kept open too long Door may be slightly open Large amount of warm or hot food have been stored recent
28. t after 3600 hours of operation After replacing the air filter reset the air filter timer by pressing the AIR FILTER key for 3 seconds The REPLACE AIR FILTER LED will be illuminated green for 3 seconds confirming a timer reset hold to reset press amp hold oF A 4 Electrolux f Ll ail alarm control off lock door ajar m power fail replace air filte Control Lock To disable the keypads on the control begin by pressing the CONTROL LOCK key for 8 seconds until LO is displayed for 1 second With the control locked when keys are pressed on the control panel LO will be displayed To unlock the control press the CONTROL LOCK key for 3 seconds The display will show UL for 1 second lt gt hold to reset press amp hold Electrolux L H O E A air temp alarm control filter mode off lock door ajar O powerfail replace air filter Power Fail The POWER FAIL indicator light informs you that due to a power failure the cabinet temperature exceeded 23 F 5 C If the power failure lasted more than 1 hour the display alternates between showing the power failure duration Hours and DURATION LED illuminate in the display and the cabinet temperature F or C illuminates every 72 second This safety feature will aid in determining what food spoilage action to take The Power Fail indicator light and duration display can be turned off by pressing the ALARM OFF key hold to reset press amp h
29. ts Luxury Design LED Ramp up Lighting Tall Basket Toe Grile Light Switch 6 Installation Required Tools You will need the following tools A CAUTION D gt Adjustable DO NOT install the appliance where the Wrench temperature will drop below 40 F 13 C or VS rise above 110 F 43 C The compressor will not be able to maintain proper temperatures inside the unit DO NOT block the toe grille on the lower front of your appliance Sufficient air circulation is essential for the proper operation of your unit Installation e Allow the following clearances for ease of installation proper air circulation and plumbing and electrical connections Sides 38 9 5 mm Top amp Back 1 25 4 mm Socket A e Allow for trim kit if it to be installed Wrench Set j with the unit This Use amp Care Guide provides general g NOTE installation and operating instructions for your model We recommend using a service or kitchen contracting professional to install your appliance Use the unit only as instructed in this Use amp Care Guide Before starting the appliance follow these important first steps NOTE Location The appliance doors are designed to shut e Choose a place that is near a by themselves within a 20 degree opening grounded non GFCI electrical outlet Do Not use an extension cord or an adapter plug e f possible place the unit out of direct Es sunlight and away from the range d
30. uch as abuse misuse inadequate power supply accidents fires or acts of God DISCLAIMER OF IMPLIED WARRANTIES LIMITATION OF REMEDIES CUSTOMER S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE REPAIR OR REPLACEMENT AS PROVIDED HEREIN CLAIMS BASED ON IMPLIED WARRANTIES NCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW BUT NOT LESS THAN ONE YEAR ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE If You Need Service Keep your receipt delivery slip or some other appropriate payment record to establish the warranty period should service be required If service is performed it is in your best interest to obtain and keep all receipts Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below This warranty only applies in the USA Puerto Rico and Canada In the USA and Puerto Rico your appliance is warranted by
31. ury burned out Design Lighting section No electric current is See APPLIANCE DOES NOT RUN reaching the appliance Control is in Sabbath Depress TEMP MODE key and mode Sb is displayed CONTROL LOCK key for on control 3 seconds Major Appliance Warranty Information 23 Your appliance is covered by a one year limited warranty For one year from your original date of purchase Electrolux will repair or replace any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed used and maintained in accordance with the provided instructions In addition the cabinet liner and sealed refrigeration system compressor condenser evaporator dryer or tubing of your appliance is covered by a two through five year limited warranty During the 2 through 5 years from your original date of purchase Electrolux will repair or replace any parts in the cabinet liner and sealed refrigeration system which prove to be defective in materials or workmanship when such appliance is installed used and maintained in accordance with the provided instructions Exclusions This warranty does not cover the following 1 Products with original serial numbers that have been removed altered or cannot be readily determined 2 Product that has been transferred from its original owner to another party or removed outside the USA or Canada Rust on the interior or exterior of the unit Products purch
32. vel and Tall Lower Basket Pull up on the front of the basket to release the basket from the retainers on the interior sides of the freezer Adjustable Door Bins This model is equipped with adjustable door bins that can be moved to suit individual needs To Move Door Bins e Lift the bin straight up e Remove the bin e Place the bin in desired position e Lower the bin onto supports until locked in place Storage Components amp Energy Saving Tips 17 Soft Freeze Tilt Out Bin The soft freeze tilt out bin is designed to be warmer than the freezer compartment It is ideal for keeping ice cream and frozen yogurt ready to serve Condiment Shelf The condiment shelf is designed to hold small items to help keep your freezer organized Locate the unit in the coolest part of the room out of direct sunlight and away from heating ducts or registers Do not place the unit next to heat producing appliances such as a range oven or dishwasher If this is not possible a section of cabinetry or an added layer of insulation between the two appliances will help the unit operate more efficiently Level the appliance so that the door closes tightly Refer to the SETTING THE TEMPERATURE CONTROL section for the suggested temperature control settings e Do not overcrowd the unit or block cold air vents Doing so causes the appliance to run lon
33. with a 20 ft copper water line with self tapping saddle valve Please refer to www electroluxappliances com for more information To Connect Water Supply Line To Ice Maker Inlet Valve 1 Disconnect freezer from electric power source 2 Place end of water supply line into sink or bucket Turn ON water supply and flush supply line until water is clear Turn OFF water supply at shutoff valve 38 Remove plastic cap from water valve inlet and discard cap 4 If you use copper tubing Slide brass compression nut then ferrule sleeve onto water supply line Push water supply line into water valve inlet as far as it will go 4 6 4 mm Slide errule sleeve into valve inlet and finger tighten compression nut onto valve Tighten another half turn with a wrench DO NOT overtighten See Figure 1 If you use stainless steel tubing The nut and ferrule are already assembled on the tubing Slide compression nut onto valve inlet and finger tighten compression nut onto valve Tighten another half turn with a wrench DO NOT overtighten See Figure 2 5 With steel clamp and screw secure water supply line copper tubing only to rear panel of freezer as shown 6 Coil excess water supply line copper tubing only about 21 2 turns behind freezer as shown and arrange coils so they do not vibrate or wear against any other surface 7 Turn ON water supply at shutoff valve and tighten any connections that
Download Pdf Manuals
Related Search