Electrolux 241868802 User's Manual
Contents
1. Fasten right and left side clips into groove of bottom hinge To remove toe grille 1 With both doors closed unfasten right and left side clips of toe grille from bottom hinge grove ANS 2 pen both a Press firmly on top of toe grille until top of toe nl a rille pops off 3 Bul toe grille outward towards your body and off of lower hinges NOTE Level the unit with the adjustable rollers before leveling the doors To level the doors using the adjustable lower hinge some models 1 Before leveling either door remove set screw that locks door height into posi tion The door cannot be adjusted without set screw removed If the refrigerator door is lower than the freezer door raise the refrigerator door by turning the adjustment screw counterclockwise using a 7 16 inch wrench See illustration If the freezer door is lower than the refrigerator door raise the freezer door b turning the adjustment screw counterclockwise using a isinch wrench See illustration After leveling verify door stop contacts lower hinge and top of door does not contact upper hinge through full movement of door from fully closed to fully open 5 Replace the toe grille by fitting it into place This document should only be removed by customer after installation 6 Remove Internal Shipping Materials Electrolux uses packing foam and tape to secure the internal parts of2. power n X j source i Fema gt lt i 2 Place end of water supply line into sink or bucket Turn ON water supply and flush sup ply line until water is clear Turn OFF water supply at shutoff valve Remove plastic cap from water valve inlet and discard cap If you use copper tubing Slide brass Fom household watr supply compression nut then ferrule Sleeve onto A tnctude enough tubing in oop to allo water supply line Push water supply line A ee ae into water valve inlet as far as it will go 14 inch 6 4 mm Slide ferrule sleeve into valve inlet and finger tighten compression nut onto valve Tighten another half turn with a wrench DO NOT over tighten See Figure 1 If you use stainless steel tubing The nut and ferrule are already assembled on the tubing Slide compression nut onto valve inlet and finger tighten compression nut onto valve Tighten another half turn with a wrench DO NOT over tighten See Figure 2 ith steel clamp and screw secure water supply line copper tubing only to rear panel of refrigerator as shown Coil excess water supply line copper tubing only about 2 turns behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface Turn ON water supply at shutoff valve and tighten any connections that leak Reconnect refrigerator to electrical power source To turn ice maker on lower wire signal arm side mounted or set the ice maker s On Of
3. O Electrolux installation Instructions for Side By Side Refrigerator Z N WARNING To avoid electric shock which can cause death or severe personal injury do not connect your refrigerator to an electrical power source until you have completed Step 3 of these instructions Tools Necessary O eS NOTE These installation instructions are OR OR provided only as a possible customer V socket Actuate txea Option Electrolux recommends that Phillips Head Wrench Set Wrench Wrench you use a service or kitchen contracting 1 professional to install your refrigerator Prepare The Installation Site Your refrigerator is designed to be part of a built in kitchen cabinet system Be sure to coordinate site preparation and E NOTE installation with your kitchen contractor Include these minimum guidelines in your site preparation Information about cabinetry construction e Choose a place near a grounded electrical outlet for Electrolux products is available for e Do not use an extension cord or an adapter plug contractors Call 1 877 435 3287 Avoid direct sunlight and close proximity to a range dishwasher or other heat source Floor should be level and able to support a fully loaded A CAUTION refrigerator The refrigerator s Ice amp Water Dispenser requires water Room temperatures below 55 F supply access i 13 C or above 110 F 43 C Plan for easy access to counter tops when removing food will impair cooling ability o
4. f power switch to the I position rear mounted NOTE e The ice maker s fill valve may operate noisily if the household water supply is shut off e After ensuring no water leaks exist at any connection be sure to check for leaks again in 24 hours e See your Use amp Care Guide for detailed information about setting up and operating the Ice amp Water Dispensing system 4 Place In Permanent Position If possible use a hand truck to position the refrigerator directly in front of its cabinet enclosure Be careful not to move the refrigerator beyond its water supply copper CAUTIO N tubing connections e Shifting the refrigerator from side to side may damage flooring Plug in the power cord and push the refrigerator straight back into place e Do not block the toe grille on the lower front of your refriger mA IMPORTANT ator Sufficient air circulation is If you are installing your refrigerator without connecting it to a water supply essential for proper operation make sure the ice maker s power switch is turned Off see the Use amp Care sila y Guide for more details 5 Level Refrigerator amp Adjust Doors if necessary To install toe grille gt rootori 1 Open both doors Slide left and right sides of toe grille over lower hinges of refrigerator 2 While pushing toe grille firmly against cabinet fasten bottom clips of toe grille to cabinet 3 Fasten top clips to cabinet 4 Close the doors
5. f your For complete access to drawers and freezer baskets refrigerator s compressor doors must be able to fully open Allow the following clearances for ease of installation proper air circulation and plumbing and electrical connections Sides amp Top 3 8 inch Rear 1 inch 2 Transport Unpackaged Refrigerator To Site By now you have already removed your refrigerator s shipping carton You may still need to use a hand truck to move it through close spaces or entrances If the refrigerator is larger than an entrance consider two options e Remove the entrance door if one exists e Remove the refrigerator doors see how in your Use amp Care Guide When using a hand truck e Load refrigerator from side of cabinet only e Do not run retaining straps over handles e Do not over tighten retaining straps e Never use refrigerator handles to move the refrigerator Remove tape from doors only after unit is in place Shifting the refrigerator from side to side may damage flooring 3 Connect Water Supply Before Installing The Water Supply Line You Will Need Basic Tools adjustable wrench flat blade screwdriver A WARNING and Phillips screwdriver Access to a household cold water line with water To avoid electric shock which can pressure between 30 and 100 psi cause death or severe personal in A water supply line made of inch 6 4mm OD copper jury disconnect the refrigerator from or stainless steel
6. is setting solid on all corners Final Checks Electrical Power OShipping material removed OFresh Food and Freezer temperatures set OCrisper Humidity controls set ORegistration Card sent in OHouse power turned on ORefrigerator plugged in P N 241868802
7. r possibilities to check e Is the power to the receptacle turned on e Is the water filter above the fresh food compartment fully seated see Use amp Care Guide for details If you still have operation problems after checking these suggestions please see the Solutions To Common Problems section in your Use amp Care Guide 8 What s Next Congratulations You are ready to begin enjoying your new Electrolux refrigerator To become aware of important safety instructions and learn how to operate your refrigerator please read the entire Use amp Care Guide You may want to start with the Normal Operating Sights amp Sounds section of the Guide to learn more about what to expect during typical operation Please register your product You can register online at www electroluxusa com or you can simply send in the Registration Card And thank you for choosing Electrolux 9 v Installation Checkoff Li Doors Ice Maker OHandles are secure and tight OHouse water supply connected to ODoor seals completely to cabinet on all sides refrigerator OFreezer door is level across the top ONo water leaks present at all connections recheck in 24 hours Leveling Olce Maker is turned ON Olce amp Water Dispenser operates correctly OF ront filter must be flush with filter housing some models ORefrigerator is level side to side and tilted 1 4 6mm front to back OToe grille is properly attached to refrigerator OCabinet
8. tubing To determine the length of electrical power before connecting a tubing needed measure the distance from the ice maker water supply line to the refrigerator inlet valve at the back of the refrigerator to your cold water pipe Then add A CAUTION approximately 7 feet 2 1 meters so the refrigerator To Avoid Property Damage Ee e Copper or Stainless Steel braided tubing is recom g mended for the water supply line Water supply tubing A shutoff valve to connect made of inch plastic is not recommended to be used the water supply line to your Plastic tubing greatly increases the potential for water household water system DO leaks and the manufacturer will not be responsible for NOT use a self piercing type any damage if plastic tubing is used for the supply line shutoff valve DO NOT install water supply tubing in areas where tem A compression nut peratures fall below freezing and ferrule sleeve for x Bit i Chemicals from a malfunctioning softener can damage the connecting a copper water ice maker If the ice maker is connected to soft water en ae to the ice maker sure that the softener is maintained and working properly Not satisfied with the installation of your refrigerator gt Please contact the store you purchased it from To Connect Water Supply Line To Ice Maker Inlet Valve Plasie water Tusing oN to Ice M ce Maker pe Fill Tube fube Brass rs 1 Disconnect refrigerator from electric
9. your refrigerator for shipping Once the refrigerator is in position you can remove this material 1 FOAM BLOCK SHELF SPACER WITH TOE GRILL 1 PIECE OF TAPE p 1 PIECE OF TAPE 4 PIECES OF TAPE 4 PIECES OF TAPE 1 BOX OF DOOR BINS 3 PIECES OF TAPE AND DAIRY COMPARTMENT 4 PIECES OF TAPE 1 PIECE OF TAPE 3 PIECES OF TAPE 2 PIECES OF TAPE 1 BOX OF DOOR HANDLES 5 PIECES OF TAPE AND 2 PIECES OF TAPE 12 PIECES OF TAPE AUi 7 PIECES OF TAPE 4 PIECES OF TAPE 2 PIECES OF TAPE 2 FOAM BLOCKS 2 PIECES OF TAPE 6 PIECES OF TAPE 1 FOAM BLOCK Location of these materials may vary depending on your model Z Problems Try These Suggestions Operation problems are possible if any of the installation tasks are not completed Here is a list of things to check for Is the refrigerator s power cord plugged in Is the refrigerator connected to the household water supply If you had to remove the refrigerator and freezer doors did you reattach water and power connectors at the door hinges See the Use amp Care Guide for detailed instructions on removing and replacing doors Is the ice maker power switch turned On Othe
Download Pdf Manuals
Related Search