Electro-Voice S60T User's Manual
Contents
1. gt FIGURE 6 Harmonic Distortion 0 1 Rated Power Input 10 watts 110 BAI MEI HORIZONTAL FREQUENCY HERTZ VERTICAL FIGURE 7 Two Examples of S 60 Mounting Using the OmniMount Series 75 Support System FIGURE 3 Beamwidth vs Frequency whole space anechoic environment BEAMWIDTH IN DEGREES 6dB on FREQUENCY IN HERTZ FIGURE 8 Dimensions FIGURE 4 Directivity vs Frequency whole space anechoic environment g a x c ix o o 20 E z o E amp E B o 8 FREQUENCY IN 2 FIGURE 9 Using the S 60MB with the S 60 IMPEDANCE 100 voit 70 volt 1670 839 3330 167 Q 667 Q 3330 1 350 Q 6672 2 700 Q 1 350 Q 5 400 Q 2 700 Q TABLE 1 Power Tap OmniMount is a registered trademark o OmniMounr Systems Inc Net Weight S 60 7 0 kg 15 4 Ib S 60T 8 4 kg 18 4 Ib Shipping Weight S 60 9 5 kg 20 9 Ib S 60T 10 9 kg 23 9 Ib DESCRIPTION The Electro Voice S 60 S 60T are compact two way constant directivity speaker systems for sound reinforcement and monitoring The small size high sensitivity and high power handling capacityof the S 60 S 60T make them an excellent choice for use in studios clubs bars theaters or other applications The combi nation of optimal crossoverfrequency and high frequency dispersion controlling Direktor en sures uniform audience c2. coverage angle is uniform which means dependable audience coverage without hot spots or dead zones at certain frequencies The 120 x 120 dispersion characteristic per mits this small system to be used either hori zontally or vertically allowing greater flexibility in setup or installation The controlled directiv ity of the high and low frequency transducers also eliminates response irregularities caused by diffraction off enclosure edges This com bined with an essentially flat on axis response produces a total acoustic power output that is uniform with frequency FREQUENCY RESPONSE The S 60 S 60T s axial frequency response was measuredin Electro Voice slarge anechoic chamber at a distance of 10 feet with a swept sine wave input of four volts No additional equalization was used Figure 1 has been aver aged and corrected for 1 watt at 1 meter DIRECTIVITY The directional characteristics of the S 60 S 60T were measured in Electro Voice s large anechoic chamber The test signal was one third octave filtered pink noise at the frequen cies indicated A full spherical measurement system was used which is compatible with the AcoustaCADD computer aided design pro gram All directional information was measured at 20 feet Figure 2 illustrates the horizontal and vertical polar responses Figure 3 shows the horizontal and vertical beamwidths Beamwidth is the angle at which the horizontal and vertical pol
3. details are included in the Uniform Limited Warranty statement Service and repair address for this product Electro Voice Inc 600 Cecil Street Buchanan Michigan 49107 616 695 6831 or 800 234 6831 Specifications subject to change without no tice ELECTRO VOICE cmarkivcompany 600 Cecil Street Buchanan Michigan 49107 MANUFACTURING PLANTS AT BUCHANAN MI IE NEWPORT TN B SEVIERVILLE TN OKLAHOMA CITY GANANOQUE ONT Electro Voice Inc 1995 B Lithoin U S A Part Number 532411 9515
4. in Direktor Low Frequency 16 5 cm 6 5 in woofer Box Tuning Frequency 60 Hz S 60 S 60T Two Way Speaker System e Two way compact system e Constant directivity system for uniform coverage e 6 5 woofer e tweeter with dispersion controlling Direktor Automatically resetting tweeter protection circuit Optional 60 W transformer with selectable taps S 60T e Available in paintable white or black Crossover Frequency 2 500 Hz Crossover Slope 12 dB per octave Impedance S 60 Nominal 8 ohms Minimum 5 ohms S 60T See Table 1 input Connections S 60 Y 4 inch phone jack with parallel 5 way binding post S 60T 5 way binding post with weatherproof cover Materials Enclosure and Baffle Board Injection molded plastic black or white Grille Punched metal powder coated black or white Mounting EV S 60MB mounting bracket or OmniMount Series 75 mounting hardware black or white Dimensions Height 35 0 cm 13 8 in Width 22 0 cm 8 7 in Depth 21 1 cm 8 4 in Y OmniMount is a registered trademark of OmniMount Systems Inc 5 60 SPECIFICATIONS GRAPHICS FIGURE 1 Axial Frequency Response FIGURE 5 Harmonic Distortion 0 01 Rated Power Input 1 watt COOL Tt HA sU LL TT pe A EB LAL Ii s FREQUENCY IN HERTZ FIGURE 2 Polar Response FREQUENCY IN HERTZ
5. Eleclro Yoice SPECIFICATIONS Frequency Response 1 Watt 1 Meter on Axis Swept Sine Wave Input Half Space Anechoic Environment 3 dB see Figure 1 60 18 000 Hz Low Frequency 3 dB Down Point 60 Hz Usable Low Frequency Limit 10 dB down point 47 Hz Half Space Reference Efficiency 0 6 Long Term Average Power Handling Capacity per EIA Standard RS 426A see Power Handling Capacity section 100 watts Maximum Woofer Acoustic Output 0 6 watts Sensitivity SPL at 1 meter 1 watt input anechoic environment band limited pink noise signal 300 2 000 Hz 88 dB Dispersion Angle Included by 6 dB Down Points on Polar Responses Horizontal and Vertical Planes Indicated One Third Octave Bands of Pink Noise see Figure 2 500 1 000 Hz 170 30 1 000 10 000 Hz 120 20 10 000 20 000 Hz 70 30 Directivity Factor R Q 800 16 000 Hz Median see Figure 4 7 3 14 9 4 5 Directivity Index D 800 16 000 Hz Median see Figure 4 8 6 dB 4 8 4 1 dB Distortion 0 1 Full Power Input see Figure 5 Second Harmonic 100 Hz 8 1 000 Hz lt 1 10 000 Hz lt 1 Third Harmonic 100 Hz 1 4 1 000 Hz lt 1 10 000 Hz lt 1 Distortion 0 01 Full Power Input see Figure 6 Second Harmonic 100 Hz 7 1 000 Hz lt 1 10 000 Hz lt 1 Third Harmonic 100 Hz lt 1 1 000 Hz lt 1 10 000 Hz lt 1 Transducer Complement High Frequency 2 5 cm 1 in tweeter with 12 5 cm 5
6. ar responses have decreased in level by 6 dB when com pared to the axial frequency response Figure 4 illustrates the total directivity of the S 60 S 60T The directivity index D is calcu lated using the formula 10 log R POWER HANDLING CAPACITY Electro Voice components and systems are manufactured to exacting standards to ensure reliability in continuous use in arduous real life conditions Besides utilizing industry standard power tests extreme in house power tests which push the performance boundaries of the loudspeakers are also performed for an extra measure of reliability The S 60 S 60T are rated asperthe ANSI EIA 426 A Loudspeaker Power Rating Full Range Test which uses a shaped random noise signal to simulate typical music to test the mechanical and thermal capabilities of the loudspeakers Specifically the 5 60 5 60T passes the ANSI EIA 426 A power test with the following test parameters 400 watts total Test Voltages 21 7 volts rms 43 4 volts peak Reg 1 15 x 4 7 ohms SUSPENDING THE S 60 S 60T The S 60 S 60T is fitted with six M6 threaded inserts and can be suspended as follows 1 S 60MB is a universal U bracket designed to allow the suspension of the S 60 at any angle and orientation from the wall or ceil ing see Figure 9 Full instructions are included with the S 60MB 2 OmniMount Series 75 support system Four M6 threaded inserts are located in the rear panel to allow use of
7. hms nominal 5 ohms minimum The enclosure shall be two piece construction with a particle board cabinet and a molded plastic baffle The unit shall be 35 0 cm 13 8 in high 22 0 cm 8 7 in wide and 21 1 Ey cm 8 4 in deep The loudspeaker system shall be the Electro Voice mode S 60 S 60T UNIFORM LIMITED WARRANTY Electro Voice products are guaranteed against malfunction due to defects in materials or work manship for a specified period as noted in the individual product line statement s below orin the individual product data sheet or owner s manual beginning with the date of original purchase If such malfunction occurs during the specified period the product will be repaired or replaced at our option without charge The product will be returned to the customer pre paid Exclusions and Limitations The Lim ited Warranty does not apply to a exterior finish or appearance b certain specific items described in the individual product line statement s below or in the individual product data sheet or owner s manual c malfunction resulting from use or operation of the product other than as specified in the product data sheet or owner s manual d malfunction re sulting from misuse or abuse of the product or e malfunction occurring at any time after re pairs have been made to the product by anyone other than Electro Voice orany of its authorized service representatives Obtaining Warranty Service To obtain wa
8. overage throughout eliminating the problems of hot spots and dead zones that might occur at certain fre quencies with other two way speaker systems The low frequency section is a 16 5 cm 6 5 in direct radiating woofer installed in an opti mally vented enclosure This results in excep tionally extended bass response and high effi ciency in a very small cabinet Both drivers feature low leakage magnet de signs and the woofer is also screened to permit use close to video monitors For very critical video monitoring applications a minimum dis tance of approximately 10 cm 4 in is recom mended between the edge of the loudspeaker and the edge of the CRT The enclosure is constructed from high impact ABS plastic which has been specially treated to allow the enclosure to be painted using com monly available finishes The system can be mounted using OmniMount Series 75 mount ing hardware or the EV S 60MB mounting bracket CONSTANT DIRECTIVITY SPEAKER SYSTEM The crossover frequency and speaker component geometries have been carefully selected so that the directional characteristics of the woofer and Direktor match atthe cross over frequency approximately 120 degrees circular coverage patterns for each to create a special system type the constant directivity system At higher frequencies the horizontal and vertical coverage pattern remains essen tially constant Response within the 120 x 120 rated
9. owever guaran tee that all commercially available paints will be satisfactory It is therefore recommended that a small area should be tested with the paint in order lo ensure that there are no adverse effects and that the paint has sufficient adhe sion Care should be taken not to get paint onto the woofer cone or the tweeter screen TWEETER PROTECTION CIRCUIT The S 60 S 60T crossover is fitted with an autornatically resetting tweeter protection de vice This new design permits short term tran sients to pass but protects the tweeter from long term power extremes that would normally destroy the tweeter ARCHITECTS AND ENGINEERS SPECIFICATIONS The loudspeaker system shall be a constant directivity two way system The speaker sys tem shall contain a 16 5 cm 6 5 in low fre quency loudspeaker and a 2 5 cm 1 in high frequency tweeter with disperison coritrolling Direktor The S 60T shall include a 60 watt line transformer installed in the vented enclo sure The line transformer shall have power taps for 60 W 30 W 15 W 7 5 W 3 8W and 1 9 W The power taps shall be switch selectable The dividing network crossover frequency shall be 2 500 Hz The loudspeaker system shall meet the following performance criteria power handling 100 watts per EIA RS 4264A fre quency response 3 dB from 70 to 18 000 Hz pressure sensitivity 88 dB SPL at 1 watt 1 meter band limited pink noise in an anechoic chamber impedance 8 o
10. rranty service a cus tomer must deliver the product prepaid to Electro Voice or any of its authorized service representatives together with proof of purchase of the product in the form of a bill of sale or receipted invoice A list of authorized service representatives is available from Electro Voice at 600 Cecil Street Buchanan MI 49107 616 695 6831 or 800 234 6831 Incidental and Consequential Damages Excluded Product repair or replacement and return to the cus tomer are the only remedies provided to the customer Electro Voice shall not be liable for any incidental or consequential damages in cluding without limitation injury to persons or property or loss of use Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Other Rights This warranty gives you specific legal nghts and you may also have other rights which vary from state to state Electro Voice Speakers and Speaker Sys tems are guaranteed against malfunction due to defects in materials or workmanship for a period of five 5 years from the date of original purchase The Limited Warranty does not apply to burned voice coils or malfunctions such as cone and or coil damage resulting fromimprop erly designed enclosures Electro Voice active electronics associated with the speaker sys tems are guaranteed for three 3 years from the date of original purchase Additional
11. the OmniMount Series 75 support system M6 hardware is provided A safety chain should be used to ensure safe operation Full instructions can be obtained from OmniMount Systems Inc 1501 W 17th St Tempe AZ 85281 Tel 602 829 8000 Fax 602 756 9000 WARNING IT IS THE RESPONSIBILITY OF THE INSTALLER TO ENSURE THAT THE MOUNTING SURFACE HAS SUFFICIENT RI GIDITY TO SUPPORT THE S 60 AND THAT THE MOUNTING BRACKET IS CORRECTLY FITTEDTOTHE SURFACE AND TO THE S 60 TRANSFORMER SETTINGS S 60T A transformer and power selector switch are installed in the rear of the enclosure The level of the S 60T may be adjusted by changing the Switch setting using a screwdriver Clockwise increase the power Since the same switch and transformer are used for either the 100 volt or 70 volt line the power setting depends upon the amplifier output that is used 100 volt or 70 volt CAUTION When connected to a 100 volt line do nol use the switch setting marked DO NOT USE as this may result in excessive power driving the S 60T or excessive distortion CONSTRUCTION The enclosure is constructed from injection molded ABS plastic The S 60 S 60T is sup pliedin an all black or all white finish and can be painted if required Both the baffle board and the enclosure have been specially treated to enhance the adhesion of paints The S 60 has been tested with sev eral commercially available paints with suc cess Electro Voice cannot h
Download Pdf Manuals
Related Search