Eiki 392 User's Manual
Contents
1. 20032. EIKI 392 Overhead Projector IMPORTANT SAFEGUARDS When using your EIKI 392 overhead projector basic safety precautions should always be followed including the following 1 2 9 Read the following instructions carefully before operating the EIKI overhead projector Make sure that the operating voltage of the overhead projector corresponds to your local voltage Care must be taken to ensure the smooth airflow of the cooling system Immediately switch off the machine if the fan is not functioning properly To avoid the potential electric shock and to ensure the stability of the optical parts do not disassemble this projector unless you are a qualified electrician and technician Tilt up the projection mirror before switching on the overhead projector Disconnect the power plug from the power source when examining or repairing the interior of the projector Only qualified service personnel should perform the maintenance and repair work To avoid the potential electrical shock do not expose this overhead projector to rain moisture or other liquids Let overhead projector cool completely before putting away Store the power cord properly in the storage area provided 10 Do not let cord hang over edge of table or counter or touch hot surfaces 11 For Pluggable equipment the socket outlet shall be installed near the equipment and shall be easily accessible A Safety Interlock is located on the edge of the cabinet W
3. e product during transit is not covered by this warranty This warranty does not apply to appearance items nor to any product whose exterior has been damaged or defaced not to any product subjected to misuse abnormal service or handling nor to any product altered or repaired by other than an Authorized Eiki Service Dealer or Service Center The provisions of this warranty does not apply to any products purchased or serviced outside the United States its territories or possessions except Canada This shall be the exclusive written warranty to the original purchaser and neither this warranty nor any other warranty expressed or implied shall extend beyond the period of the time listed In no event shall Eiki be liable for consequential economic damage to property Some states do not allow a limitation or exclusion of implied warranties or consequential damages so the above limitation and exclusion may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from state to state For questions concerning this warranty or to obtain the name and address of the nearest authorized Eiki Service Dealer or Service Center call or write Eiki International Inc at one of the following EIKI International Inc EIKI International Inc 30251 Esperanza 2 310 First St Unit 2 Rancho Santa Margarita Midland Ontario Canada CA 92688 2132 L4R 3N9 949 457 0200 705 527 4084 Printed in China Ver 01 May
4. hen the platen of the overhead projector is opened the power supply will cut off Please make sure the platen is opened during repair to avoid electric stock TABLE OF CONTENTS Name of Parts Specifications and Technical Data Operation Procedure Maintenance amp Repair Page NAME OF PARTS Head Mirror Safety Interlock at the edge of the cabinet Stage Glass Fresnel Lens Lock Lever Stage Lock Lamp Change Knob Power Switch SPECIFICATIONS AND TECHNICAL DATA Lamp EYB 360 watt Voltage 120V 60Hz Lamp changer Provides space and ability to switch between lamps Single Lamp Provided Safety switch Automatic Power Shut Off Working stage 10 X 10 Projection angle 360 rotation and tilting angle up to 60 Focal length Single Element lens f 285mm Light output 2200 Lumens Packing dimensions 20 7 X18 7 X13 3 Gross Weight 21 12 Ibs OPERATION PROCEDURE 1 Be sure the voltage of AC outlet corresponds to the projector before connecting the AC power cord 2 Pull up the post to set up the Head Mirror to an up right position until the post is locked automatically See fig 1 fig 1 fig 2 3 Tilt up the projection mirror 4 Turn the switch on the projector 5 Adjust the projection mirror horizontally and vertically to center the light on the screen 6 Place transparency on the projectio
5. n stage and adjust the focus knob to obtain a sharp image 7 After projection press down the Lock Lever to fold down the post to the stopper See fig 2 MAINTENANCE AND REPAIR 1 Replacing the lamp a Disconnect the power before replacing the lamp b Wait until the lamp is cooled down Pull the stage lock to open the projection stage Push the lever to open the condenser lens frame See fig 3 Remove the defective lamp and replaced it with a new lamp Adjust the filament to the center of the reflector See fig 4 f Place the condenser lens frame to original position and close the projection stage a o e fig 3 fig 4 2 Cleaning and assembling of the Fresnel Lens Remove the Fresnel Lens to wash with water and detergent Do not use spirit solvent fig 5 3 To assemble the Fresnel Lens make sure the UP side faced the stage glass See fig 5 Limited 3 Year Warranty Eiki International warrants this product when sold to the original purchaser from an authorized Eiki dealer to be free from defective materials and workmanship for a period of 3 years Lamp and fuses excluded Eiki agrees to repair any defect or furnish a new or equal part through an authorized Eiki Service Dealer or Service Center without charge within this period It shall be the obligation of the purchaser to provide proof of purchase and cover all transportation charges to and from the service facility Damage or loss to th
Download Pdf Manuals
Related Search