Echo PAS-265 User's Manual
Contents
1. FUEL FILTER Level 1 Tools required 200 250 mm 8 10 in length of wire with one end bent into a hook clean rag funnel and an approved verna fuel container Wy Parts required REPOWER AIR amp FUEL FILTER KIT E A WARNING Fuel is VERY flammable Use extreme care when mixing storing or handling 1 Usea clean rag to remove loose dirt from around fuel cap and empty fuel tank 2 Use the fuel line hook to pull the fuel line and filter from the tank 3 Remove the filter from the line and install the new filter 18 MECHO SPARK PLUG Level 2 Tools Required T Wrench feeler gauge soft metal brush Parts Required REPOWER Tune Up Kit IMPORTANT Use only NGK BPM 8Y spark plug BPMR 8Y in Canada other wise severe engine damage may occur 1 Remove spark plug and check for fouling worn and rounded center electrode 2 Clean the plug or replace with a new one DO NOT sand blast to clean Remaining sand will damage engine 3 Adjust spark plug gap by bending outer electrode 4 Tighten spark plug to 150 170 kgf cm 130 150 in Ibf COOLING SYSTEM Level 2 Tools required Cross Head Screwdriver 3 amp 4 mm Hex Wrench Cleaning Brush 25 50 mm 1 2 in Parts Required None if you are careful IMPORTANT To maintain proper engine operating temperatures cooling air must pass freely through the cylinder fin area This flow of air carri2. 22 ED HE LUBRICATION Level 1 Tools required 5 mm Hex Wrench Clean Rag Parts Required POWER BLENDX 8 oz P N 91014 or Lithium Base Grease Drive Shaft Upper IMPORTANT The drive shaft must be lubricated with high temperature auto motive grease every 25 hours of operation otherwise drive shaft assembly overheating and failure can result Loosen clamping knob A Pull locator pin B and rotate 1 4 turn counter clockwise to lockout position Remove attachment Remove coupler E from upper drive shaft assembly by loosening clamping screw C and removing set screw D Remove upper flex cable F wipe clean and apply a thin coating of 1 2 oz 15ml of grease Install cable Make sure that the flex cable fully engages into the clutch square drive socket Slide coupler on upper drive shaft until fully seated and align set screw hole in coupling with hole in upper drive shaft Install and tighten set screw D and tighten clamping screw C PRo ATTACHMENT SERIES OPERATOR S MANUAL 2 3 TROUBLESHOOTING ENGINE PROBLEM TROUBLESHOOTING CHART Status Fuel at carburetor No fuel at carburetor Fuel strainer clogged Clean or replace Fuel line clogged Clean or replace Carburetor See your Echo dealer Fuel at cylinder No fuel at cylinder See your Echo dealer Muffler wet with fuel Fuel Mixture too rich Open choke Engine Clean repla
3. 4 Clean carbon deposits from muffler components NOTE When cleaning carbon deposits be careful not to damage the cata lytic element inside muffler 5 Replace screen if it is cracked plugged or has holes burned through 6 Assemble components in reverse order 20 MECHO Exhaust Port Cleaning Level 2 Tools required 4mm Hex Wrench Wood or plastic scraper EJ Parts Required As needed Heat Shield 1 Remove spark plug lead from spark plug and remove engine cover 2 screws 2 Place piston at top dead center Remove muffler A and heat shield B 3 Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port IMPORTANT Never use a metal tool to scrape carbon from the exhaust port Do not scratch the cylinder or piston when cleaning the exhaust port Do not allow carbon particles to enter the cylinder 4 Inspect heat shield and replace if damaged 5 Install heat shield and muffler 6 Tighten muffler mounting bolts or nuts to 80 95 inelbf 90 110 kgfecm 7 Install engine cover and attach spark plug lead 8 Start engine and warm to operating temperature 9 Stop engine and re tighten mounting bolts or nuts to specifica tions Pro ATTACHMENT SERIES CARBURETOR ADJUSTMENT Engine Break In New engines must be operated a minimum duration of two tanks of fuel break in before carburetor adjustments can be made During the break
4. Tiller Cultivator X 1 See SRM PAS SB Blade Set up Guide for blade use requirements 2 Use J Handle provided with Pro Thatch attachment as a barrier 3 Brushcutter requires U Handle amp Harness 12 MECHO OPERATION A WARNING Moving parts can amputate fingers or cause severe injuries Keep hands clothing and loose objects away from all openings Always stop engine disconnect spark plug and make sure all moving parts have come to a complete stop before removing obstructions clearing debris or servicing unit AA warnine Engine exhaust IS HOT and contains Carbon Monoxide CO a poison gas Breathing CO can cause unconscious ness serious injury or death Exhaust can cause serious burns ALWAYS position unit so that exhaust is directed away from your face and body A WARNING Operation of this equipment may create sparks that can start fires around dry vegetation This unit is equipped with a spark arrestor and a spark arrestor may be required The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements FUEL NOTICE Use of unmixed improperly mixed or fuel older than 90 days stale fuel may cause hard starting poor performance or severe engine damage and void the product warranty Read and follow instructions in the Storage section of this manual AA warnine Alternative fuels such as E 15 15 ethanol E 85 85 ethanol or any fuels not m
5. Clutch Engagement Speed Wide Open Throttle Speed W O T with Nylon Line Head Wide Open Throttle Speed W O T with Blade PRo ATTACHMENT SERIES OPERATOR S MANUAL 25 PAS 265 1036 mm 40 8 in 248 mm 9 8 in 251 mm 9 875 in 4 8 kg 10 6 Ib Air cooled two stroke single cylinder gasoline engine 34 0 mm 1 34 in 28 0 mm 1 10 in 25 4 cc 1 55 cu in Spark arrestor muffler or spark arrestor muffler with catalyst Zama w purge pump CDI capacitor discharge ignition NGK BPM 8Y Gap 0 65 mm 0 026 in Mixed Gasoline and Two stroke Oil 50 1 Power Blend XTM SO L EGD ISO CD 13738 and J A S O M345 FC FD two stroke air cooled engine oil Use 89 Octane unleaded Do not use fuel containing methyl alcohol more than 10 ethyl alcohol or 15 MTBE Do not use alternative fuels such as E 15 or E 85 Power Blend X Premium Universal 2 Stroke Oil 0 58 ht 19 6 US fl oz Automatic Rewind Starter Centrifugal Type 6 35 mm 1 4 in flexible shaft 2 700 3 100 RPM 3 900 RPM 9 000 10 000 RPM 9 500 11 000 RPM 26 MECHO ECHO APPROVED OPTIONAL ATTACHMENTS A WARNING Use only ECHO approved attachments for Pro Attachment Series models Serious injury may result from the use of non approved attachment combinations Read and comply with all safety instructions listed in this manual and in the attachment manual RECOMMENDED OPTIONAL ATTACHMENTS 99944200590 99944200595 999
6. in period your engine performance will increase and exhaust emissions will stabilize Idle speed can be adjusted as required High Altitude Operation This engine has been factory adjusted to maintain satisfactory starting emission and durability performance up to 1 100 feet above sea level ASL 96 0 kPa To maintain proper engine operation and emission compliance above 1 100 feet ASL the carburetor may need to be ad justed by an authorized ECHO service dealer IMPORTANT If the engine is adjusted for operation above 1 100 feet ASL the carburetor must be re adjusted when operating the engine below 1 100 feet ASL otherwise severe engine damage may result Level 2 Tools required Screwdriver Tachometer ECHO P N 99051130017 Parts required None NOTE Every unit is run at the factory and the carburetor is set in compli ance with emission regulations Carburetor adjustments other than idle speed must be performed by an authorized ECHO dealer 1 Check idle speed and reset if necessary If a tachometer is avail able idle speed screw A should be set to the specifications found on page 24 Specifications of this manual Turn idle screw A clockwise to increase idle speed counter clockwise to decrease idle speed A WARNING When carburetor adjustment is completed the cutting attachment should not turn at idle otherwise serious personal injury may result OPERATOR S MANUAL 21
7. SYSTEM MAINTENANCE PROCEDURE aie ee j paka LEVEL USE HOURS I EE il Em Eg Erg El EX al i md 10 Spark Plug linspectiClean f 1 EC NEN e E IQ Cooling System Inspect Clean Inspect Clean Replace MAINTENANCE PROCEDURE LETTER CODES 1 INSPECT R REPLACE C CLEAN IMPORTANT NOTE Time intervals shown are maximum Actual use and your experience will determine the frequency of required maintenance MAINTENANCE PROCEDURE NOTES 1 Apply POWER BLENDX every 25 hours of use 2 Low evaporative fuel tanks DO NOT require regular maintenance to maintain emission integrity All recommendations to replace are based on the finding of damage or wear during inspection IC PRo ATTACHMENT SERIES OPERATOR S MANUAL 1 7 AIR FILTER Level 1 Tools required 25 or 50 mm 1 or 2 in Cleaning brush Parts required REPOWER AIR amp FUEL FILTER KIT 1 Close choke Cold Start Position hp This prevents dirt from entering the carburetor throat when the air filter is removed Brush accumulated dirt from air cleaner area 2 Remove air filter cover Brush dirt from inside cover 3 Remove air filter and lightly brush debris from filter Replace filter if it is damaged fuel soaked very dirty or the rubber sealing edges are deformed 4 If filter can be reused be certain it Fits tightly in the air filter cavity Is installed with the original side out 5 Install air filter cover
8. return handle slowly DO NOT let handle snap back or damage to unit will occur PURGE BULB Pumping purge bulb before starting engine draws fresh fuel from the fuel tank purging air from the carburetor Pump purge bulb until fuel is visible and flows freely in the clear fuel tank return line Pump purge bulb an additional 4 or 5 times AIR CLEANER Contains replaceable filter element CHOKE The choke control lever is located on the top of the air cleaner case Move choke lever to COLD START dh position to close choke for cold starting Move choke lever to the RUN d b position to open choke SPARK PLUG Provides spark to ignite fuel mixture TOP GUARD Protects arm from the hot engine DRIVE SHAFT COUPLER Includes Locator Pin and Clamping Knob FRONT HANDLE The Front Handle is assembled to the Upper Drive Shaft assembly and must be positioned for proper cutting attitude and operator comfort STOP SWITCH SLIDE SWITCH mounted on top of the Throttle Trigger Housing Move switch FORWARD to RUN BACK to STOP THROTTLE TRIGGER LOCKOUT This lever must be held during aceleration Operation of the throttle trigger is prevented unless throttle trigger lockout lever is depressed GRIP Rear right hand handle THROTTLE TRIGGER Spring loaded to return to idle when released During acceleration press trigger gradu ally for best operating technique UPPER DRIVE SHAFT ASSEMBLY Includes the Rear Right Han
9. form shape description application Read and under stand Operator s Manual Wear eyes ears and head protec tion Hot Surface AL Avoid all power lines This unit is not insulated against electrical current Keep bystand ers at least 15 m 50 ft away Fuel and oil mixture Finger Severing Wear hand protection Use two handed DO NOT smoke near fuel Do not operate closer than 15 m 50 ft from elec trical hazards Plan retreat path from falling objects DO NOT allow flames or sparks near fuel e D Choke Control Cold Start Position Choke Closed Choke Control Run Position Choke Open Carburetoradjust ment Low speed mixture Wear slip resis tant foot wear Ignition ON OFF Primer bulb Carburetor adjust ment High speed mixture Carburetor adjust ment Idle speed 4 MECHO PERSONAL CONDITION AND SAFETY EQUIPMENT WARNING Pro Attachment Series users risk injury to themselves and others if the Pro Attachment Series unit is used im properly and or safety precautions are not followed Proper clothing and safety gear must be worn when operating a Pro Attachment Series unit Physical Condition Proper Clothing Your judgment and physical dexterity may not be good Wear snug fitting durable clothing if you are tired or sick Pants should have long legs shirts with long sleeves if you are taking medication DO NOT WEAR SH
10. head assembly must be in line with the engine Rotate locator pin A 1 4 turn clockwise to engage lower shaft hole Insure locator pin is fully engaged by twisting lower drive shaft Locator pin should snap flush in coupler Full engagement will prevent further shaft rotation Secure lower shaft assembly to coupler by tightening clamping knob D 10 MECHO FRONT HANDLE ADJUSTMENT BARRIER BAR ASSEMBLY Tools Required Screwdriver Parts Required Barrier Bar Handle Adjustment NOTE Label shows minimum spacing for front handle location 1 Stand in a comfortable operating position with attachment assem bled and position front handle for comfortable operation Tighten handle screws Barrier Bar Assembly NOTE The barrier bar may be used with the PAS attachments indicated in the barrier bar table 1 Unscrew bottom bracket of handle and replace with Barrier Bar as shown Adjust handle and secure as described above MIN SPACING PRo ATTACHMENT SERIES OPERATOR S MANUAL 11 BARRIER BAR USE PAS SB ATTACHMENTS PAS ATTACHMENT RECOMMENDED OPTIONAL QU ieee Brushcutter xX Edger Curved Shaft Edger Straight Shaft Hedge Trimmer Hedge Trimmer Articulating Hi Torque Head Std Trimmer Power Pruner Pro Paddle Pro Sweep Pro Thatch Rapid Loader Line Trimmer Standard Line Trimmer
11. instruc tions on them If a decal cannot be read a new one can be ordered from your ECHO dealer See PARTS ORDERING instructions for specific information Hot Decal near muffler P N X505002310 Shaft Decal Spanish Decal English Translation P N 89022809560 ADVERTENCIA A PELIGRO Esta unidad puede ser peligrosa y producir lesiones personales graves si no se usa en forma adecuada ara reducir el riesgo de lesionarse los operadores los ayudantes y los espectadores deben leer y WARNING A DANGER This unit can be dangerous and cause serious injury if improperly used to reduce bio ek dg helpers P N X505001 930 and bystanders read and understand the Operator s and Safety Manuals which are provided in Spanish comprender el Manual Del Operador y los Manuales 89022809560 De Seguridad que se entregan escritos en espa ol q g p 8 MECHO l POWER HEAD Includes the Engine Clutch Fuel System Ignition System and Recoil Starter SPARK ARRESTOR MUFFLER OR SPARK ARRESTOR MUFFLER WITH CATALYST The muffler or catalytic muffler controls exhaust noise and emission The spark arrestor screen prevents hot glowing particles of carbon from leaving the muffler Keep exhaust area clear of flammable debris FUEL TANK Contains fuel and fuel filter FUEL TANK CAP Covers and seals fuel tank opening RECOIL STARTER HANDLE Pull handle slowly until recoil starter engages then quickly and firmly When engine starts
12. special incidental or consequential damage including lost profits There are no warranties extended other than as provided herein This limited warranty may be modified only by ECHO 99922201032 12 03 09 PRo ATTACHMENT SERIES OPERATOR S MANUAL ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENT FOR ECHO AND SHINDAIWA BRANDS The Environmental Protection Agency EPA and the California Air Resources Board C A R B and ECHO Incorporated ECHO Inc are pleased to explain the emission control system warranty on your 2010 and later equipment small off road engine SORE New equipment SORE must be designed built and equipped to meet stringent EPA and C A R B anti smog standards ECHO Inc must warrant the emission control system on your equipment SORE for the periods of time listed below provided there has been no abuse neglect or improper maintenance of your equipment SORE Your emission control system may include parts such as carburetor fuel injection system ignition system catalytic converter muffler fuel tank fuel feed lines fuel cap assembly spark plug air filters and other associated components Where a warrantable condition exists ECHO Inc will repair your equipment SORE at no cost to you including diagnosis parts and labor The Emission Control System warranty is extended to the original owner including all subsequent owners MANUFACTURER S WARRANTY COVERAGE The emission control system is warranted for 2 years or th
13. storage laws vary by locality Contact your local gov rS stabilizer is added ernment for the laws affecting your area As a precaution store fuel in an approved airtight container Store in a well ventilated unoccupied building away from sparks and flames IMPORTANT Stored two stroke fuel may separate ALWAYS shake fuel container thor oughly before each use 14 MECHO STARTING COLD ENGINE A WARNING The attachment will operate immediately when the engine starts and could result in loss of control and possible serious injury Keep movable parts of the attachment off the ground and away from objects that could become entangled or thrown 1 Stop Switch Move stop switch button A forward away from the STOP posi tion 2 Choke Lever Move choke lever B to Cold Start th Position 3 Purge Bulb Pump purge bulb C until fuel is visible and flows freely in the clear fuel tank return line Pump bulb an additional 4 or 5 times 4 Recoil Starter Lay the unit on a flat area and keep movable attachment parts clear of all obstacles Firmly grasp right hand grip and throttle trigger lockout with left hand and fully depress throttle trigger to wide open position Rapidly pull recoil starter handle rope D until engine fires or maximum five 5 pulls 5 Choke After engine fires or 5 pulls move choke lever back to Run position Hold throttle trigger and throttle trigger lockout f
14. 2010 29 30 MECHO PRo ATTACHMENT SERIES OPERATOR S MANUAL 3 1 NOTES SERVICING INFORMATION PARTS SERIAL NUMBER Genuine ECHO Parts and ECHO REPOWER Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer When you do need to buy parts always have the Model Num ber Type and Serial Number of the unit with you You can find these numbers on the engine housing For future reference write them in the space provided below YAMABIKO CORP ASSEMBLED IN USA Lr Model No SN SERVICE DEALER Call Service of this product during the warranty period must be performed q 432 ECH by an Authorized ECHO Service Dealer For the name and address of 800 43 CHO the Authorized ECHO Service Dealer nearest you ask your retailer or 1 800 432 3246 call 1 800 432 ECHO 3246 Dealer information is also available on or our Web Site When presenting your unit for Warranty service repairs proof of purchase is required www echo usa com ECHO CONSUMER PRODUCT SUPPORT If you require assistance or have questions concerning the applica CONSUMER PRODUCT tion operation or maintenance of this product you may call the ECHO SUPPORT Consumer Product Support Department at 1 800 673 1558 from 8 30 am to 4 30 pm Central Standard Time Monday through Friday Before 1 800 673 1 558 calling please know the model and serial number of your unit 8 30 4 30 Mon Fri C S T WARRANTY REGISTRATION To ensur
15. 44200600 99944200470 99944200475 99944200480 99944200485 99944200510 99944200513 99944200530 99944200540 99944200610 99944200545 99944200550 99944200553 Articulating Hedge Trimmer Articulating Hedge Trimmer Brushcutter Curved Shaft Edger Straight Shaft Edger Hedge Trimmer Hedge Trimmer Tiller Cultivator Tiller Cultivator PowerPrunerTM Standard Line Trimmer Rapid Loader Trimmer Hi Torque Head w Trimmer ProSweep M ProSweep M ProThatchTM ProThatchTM ProPaddleTM 99944200560 99944200563 99944200620 3 Foot Extension 99944200535 For use with Articulating Hedge Trimmer Hedge Trimmer and PowerPruner Attachments ONLY NOTE ECHO INC will not be responsible for the failure of cutting devices attachments or accessories which have not been tested and approved by ECHO for use with this Pro Attachment Series unit PRo ATTACHMENT SERIES OPERATOR S MANUAL 2 7 WARRANTY STATEMENTS ECHO LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01 01 2010 ECHO S RESPONSIBILITY ECHO Incorporated s Limited Warranty provides to the original purchaser that this ECHO product is free from defects in material and workmanship Under normal use and maintenance from date of purchase ECHO agrees to repair or replace at ECHO s discretion any defective product free of charge at any authorized ECHO servicing dealer within listed below application time periods limitation
16. MECHO Pro Attachment Series Operator s Manual MODEL PAS 265 WARNING DANGER A WARNING A ug The muffler or catalytic muffler The engine exhaust from this product contains chemicals known and surrounding cover may become ahdliishliin extremely hot Always keep clear of exhaust and muffler area otherwise serious personal injury may occur to the State of California to cause cancer birth defects or other reproductive harm A WARNING Read rules for safe operation and instructions carefully ECHO provides an Operator s Manual with this unit and a separate Operator s Manual and Safety Manual if avail able with the attachment All manuals must be read and understood for proper and safe operation Failure to do so could result in serious injury X7502024003 X750010523 12 09 2 MECHO INTRODUCTION Welcome to the ECHO family This ECHO product was designed and manufactured to provide long life and on the job dependability Read and understand this manual as well as your attachment operator s manual and SAFETY MANUAL if available before operation You will find these manuals easy to read and full of helpful operating tips and SAFETY messages THE OPERATOR S MANUAL Read and understand this manual before operation Keep it in a safe place for future reference It contains specifications and information for operation starting stopping maintenance storage and assembly specific to this product THE ATTACHMEN
17. ORTS if you have taken alcohol or drugs DO NOT WEAR TIES SCARFS JEWELRY Operate unit only if you are physically and mentally well Wear protective hair covering to contain long hair Wear sturdy work shoes with nonskid soles Eye Protection DO NOT WEAR OPEN TOED SHOES Wear eye protection that meets ANSI Z87 1 or CE re DO NOT OPERATE UNIT BAREFOOTED quirements whenever you operate the unit Keep long hair away from engine and air intake Retain hair with cap or net Hand Protection Wear no slip heavy duty work gloves to improve your Hot Humid Weather grip on the handles Gloves also reduce the transmission Heavy protective clothing can increase operator fatigue of machine vibration to your hands which may lead to heat stroke Schedule heavy work for early morning or late afternoon hours when temperatures Hearing Protection are cooler ECHO recommends wearing hearing protection whenever unit is used Vibration and Cold It is believed that a condition called Raynaud s Phenomenon which affects the fingers of certain individuals may be brought about by exposure to vibration and cold Exposure to vibration and cold may cause tingling and burning sen sations followed by loss of color and numbness in the fingers The following precautions are strongly recommended because the minimum exposure which might trigger the ailment is unknown Keep your body warm especially the head neck feet ankles hands and wrists Ma
18. R III The emission control system for the engine is EM TWC Engine Modification and 3 way Catalyst and for the fuel tank the Control System is EVAP Evaporative Emissions or N for nylon tank Evaporative emission may be applicable to California models only EMISSION CONTROL INFORMATION EMISSION CONTROL INFORMATION ENGINE FAMILY BEHXS 02 14KG DISPLACEMENT 21 2oc ENGINE FAMILY BEHXS 0454KA DISPLACEMENT 45 0cc EMISSION COMPLIANCE PERIOD 300 HOURS EMISSION COMPLIANCE PERIOD 300 HOURS THIS BAGINE MEETS US EPA EINEYP AND CALIFORNIA THIS ENGINE MEETS US EPA EYHEVP REGS FOR MODEL YERE 3 EN AD OP RES BEER RR DRE REFER TO OWNER S MANUAL FOR MAINTENANCE SION REGULATIONS FOR SORE SPECIFICATIONS AND ADJUSTMENTS REFER TO OWNER S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS YAMABIKO CORP 3 x xj An Emission Control Label is located on the engine This is an EXAMPLE ONLY information on label varies by engine FAMILY PRODUCT EMISSION DURABILITY EMISSION COMPLIANCE PERIOD The 300 hour emission compliance period is the time span selected by the manufacturer certifying the engine emis sions output meets applicable emissions regulations provided that approved maintenance procedures are followed as listed in the Maintenance Section of this manual PRo ATTACHMENT SERIES OPERATOR S MANUAL DESCRIPTION Locate these safety decals on your unit Make sure the decals are legible and that you understand and follow the
19. T OPERATOR S MANUAL nt Series MECHO Read and understand this manual before operation Keep it in a safe place for future reference It contains specifications and information for operation and maintenance specific to the attachment THE SAFETY MANUAL If available for attachment Read and understand this manual before operation Explains possible hazards and what measures you should take to insure safe operation TABLE or CONTENTS Introduction The Operator s Manual Manual Safety Symbols and Important Information 3 International Symbols Personal Condition and Safety Equipment Equipment Emission Control Description Contents Assembly Attachment Shaft Assembly Front Handle Adjustment Barrier Bar Assembly Starting Cold Engine Starting Warm Engine Stopping Engine Maintenance Skill Levels Maintenance Intervals Air Filter Fuel Filter Spark Plug Cooling System Cleaning Exhaust System Carburetor Adjustment High Altitude Operation Lubrication Troubleshooting Storage Specifications Recommended Optional Attachments Warranty Statements Servicing Information Parts Serial Number Service ECHO Consumer Product Support Warranty Card Additional or Replacement Manuals Specifications descriptions and illustrative material in this literature are as accurate as known at the time of publication but are subject to change CopyrightO 2010 By Echo Incorporated All Rights Reserved without notice Ill
20. amage caused by dirt pressure or steam cleaning the unit salt water corrosion rust varnish abrasives and moisture Defects malfunctions or failures resulting from abuse misuse neglect modifications alterations normal wear improper servicing or use of unauthorized attachments Incorrect storage procedures stale fuel including failure to provide or perform required maintenance services as prescribed in the operator s manual Preventative maintenance as outlined in the operators manual is the customer s responsibility Failures due to improper set up pre delivery service or repair service by anyone other than authorized ECHO servicing dealer during the warranty period Certain parts and other items are not warranted including but not limited to lubricants starter cords and engine tune ups Use of spark plugs other than those meeting performance and durability requirements of the OEM spark plug listed in the Operator s Manuals Overheating or carbon scoring failures due to restricted clogged exhaust port or combustion chamber including damage to spark arrester Screen Adjustments after the first 30 thirty days and beyond such as carburetor adjustment and throttle cable adjustment Damage to gears or gear cases caused by contaminated grease or oil use of incorrect type or viscosity of lubricants and or failure to comply with recommended grease or oil change intervals Damage caused by loading SHRED N VAC beyond recommended ca
21. ce air filter cranks Adjust carburetor starts hard See your Echo dealer doesn t start Spark at end No spark Stop switch off Turn switch to ON of plug wire Electrical problem See your Echo dealer Interlock switch See your Echo dealer Spark at plug No spark Spark gap incorrect Adjust to 65mm 0 026 in Covered with carbon Clean or replace Fouled with fuel Clean or replace Plug defective Replace plug Air filter Air filter dirty Clean or replace Fuel vent Fuel vent plugged Contaminants residues in Clean or replace Engine runs fuel but dies or does not Spark Plug Plug dirty worn Clean and adjust or replace accelerate Cooling System Cooling system Extended operation in Clean dirty plugged dirty dusty locations Spark Arrestor Spark arrestor Normal wear Replace Screen screen plugged Engine does N A N A Internal engine problem See your Echo dealer not crank Fuel filter Fuel filter dirty Contaminants residues in fuel A DANGER Fuel vapors are extremely flammable and may cause fire and or explosion Never test for ignition spark by ground ing spark plug near cylinder plug hole otherwise serious personal injury may result 24 MECHO STORAGE Long Term Storage over 30 days A WARNING During operation the muffler or catalytic muffler and surrounding cover become hot Always keep exhaust area clear of flammable debris during transportation or when storing otherwise serious property damage or personal injury
22. d Handle Assembly Front Left Hand Handle Assembly Flexible Drive Cable Drive Shaft Assembly Coupler and Power Head BARRIER BAR Helps keep the cutting attachment away from the operator s legs and feet by limiting rearward movement of the unit if kick out occurs Not for use as a handle Allows use of all Echo approved accessories and attachments PRo ATTACHMENT SERIES OPERATOR S MANUAL 9 CONTENTS The ECHO product you purchased has been factory pre assembled for your convenience Due to packaging restrictions other assembly may be necessary After opening the carton check for damage Immediately notify your retailer or ECHO Dealer of damaged or missing parts Use the contents list to check for missing parts 1 Power Head w Upper Drive Shaft Assembly MECHO 1 Plastic Bag co pack 1 Operator s Manual 1 Warranty Registration Card 1 Safety Glasses 1 Barrier Bar ASSEMBLY ATTACHMENT SHAFT ASSEMBLY Tools Required None Parts Required PAS Attachment Assembly 1 Set Power Head Shaft Assembly on a level surface 2 Pull locator pin A out and turn counter clockwise 1 4 turn to lock out position Remove cardboard spacer if necessary Carefully fit attachment drive shaft assembly into coupler B to decal assembly line C making sure that the inner lower drive shaft engages into the square upper drive shaft socket NOTE Lower bearing housing and
23. e length of the ECHO Inc warranty whichever is longer If any emission related part on your equipment is defective the part will be repaired or replaced by ECHO Inc or its Authorized Service Representative OWNER S WARRANTY RESPONSIBILITIES As the equipment SORE owner you are responsible for the performance of the required maintenance listed in your Operator s Manual ECHO Inc recommends that you retain all receipts covering maintenance on your equipment SORE however ECHO Inc cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance As the equipment SORE owner you should be aware that ECHO Inc may deny you warranty coverage if your equipment SORE or a part has failed due to abuse neglect improper maintenance or unapproved modifications You are responsible for presenting your equipment SORE to an ECHO Inc authorized service representative as soon as a problem exists The warranty repairs should be completed in a reasonable amount of time not to exceed 30 days If a warrantable condition exists and there is no Authorized Dealer within 100 miles ECHO Inc will pay to ship the unit to the nearest authorized dealer If you have questions regarding your warranty coverage you should contact ECHO Inc at 1 800 673 1558 web site WWW ECHO USA COM or contact Shindaiwa at 1 877 986 7783 web site WWW SHINDAIWA COM WHAT DOES THIS WARRANTY COVER ECHO Inc warrants that your eq
24. e trouble free warranty coverage it is important that you regis ter your ECHO equipment on line at www echo usa com or by filling out the warranty registration card supplied with your unit Registering your product confirms your warranty coverage and provides a direct link between you and ECHO if we find it necessary to contact you ADDITIONAL OR REPLACEMENT MANUALS Replacement Operator Safety Manuals and Parts Catalogs are available from your ECHO dealer or at www echo usa com or by contacting ECHO Inc 400 Oakwood Road Lake Zurich IL 60047 800 673 1558 Always check the ECHO Web Site for updated information Safety Videos are available from your Echo dealer A 5 00 shipping charge will be required for each video MECHO ECHO INCORPORATED 400 Oakwoop Roan LAKE ZuURicH IL 60047 S75411001001 S75411999999 i 600 S67911001001 S67911999999 www echo usa com 86312001001 S863 12999999
25. eeting ECHO requirements are NOT approved for use in ECHO 2 stroke gasoline engines Use of alternative fuels may cause performance prob lems loss of power overheating fuel vapor lock and unintended machine operation including but not limited to improper clutch engagement Alternative fuels may also cause premature deterioration of fuel lines gaskets carbu retors and other engine components Fuel Requirements Gasoline Use 89 Octane R M 2 mid grade or higher gasoline known to be good quality Gasoline may contain up to 10 Ethanol grain alcohol or 15 MTBE methyl tertiary butyl ether Gasoline containing methanol wood alcohol is NOT approved Two Stroke Oil A two stroke engine oil meeting ISO L EGD ISO CD 13738 and J A S O FC FD Standards must be used Echo brand premium Power Blend X Universal 2 Stroke Oil meets these standards Engine problems due to inadequate lubrication caused by failure to use an ISO L EGD ISO CD 13738 and J A S O FC ED certified oil such as Echo premium Power Blend X will void the two stroke engine warranty IMPORTANT Echo premium Power Blend X Universal 2 Stroke Oil may be mixed at 50 1 ratio for application in all Echo en gines sold in the past regardless of ratio specified in those manuals PRo ATTACHMENT SERIES OPERATOR S MANUAL 13 Handling Fuel A WARNING Fuel is VERY flammable Use extreme care when mixing storing or handling or serious personal injury
26. enance is warranted for the period of time prior to the first scheduled replacement point for that part Any such part repaired or replaced under warranty shall be warranted for the remainder of the period prior to the first scheduled replacement point for that part Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repairs on emission related parts and must be provided without charge if the part is still under warranty Any replacement part that is equivalent in performance and durability may be used in non warranty maintenance or repairs and shall not reduce the warranty obligations of the manufacturer Throughout the equipment SORE warranty period ECHO Inc will maintain a supply of warranted parts sufficient to meet the expected demand for such parts SPECIFIC EMISSION RELATED WARRANTED PARTS Electronic Ignition System Spark Plug Catalytic Converter Muffler Assembly Carburetor complete assembly or replaceable components Choke Fuel Injection Assembly or replaceable components Fuel Tank Fuel Cap Assembly Air Filter Fuel Feed Line and associated clamps connectors as applicable WHAT IS NOT COVERED Any failure caused by abuse neglect improper maintenance unapproved modifications use of unapproved add on parts modified parts or unapproved accessories This Emission Control Warranty is valid only for the U S A it s Territories and Canada 99922201033 01
27. ent combination Read and comply with all safety instructions listed in this manual and attachment manual NOTE ECHO INC will not be responsible for the failure of cutting devices attachments or accessories which have not been tested and approved by ECHO for use with this Pro Attachment Series Check unit for loose missing nuts bolts and screws Tighten and or replace as needed Inspect guards for damage and ensure that they are securely in place Replace if guard is damaged or missing Check that the attachment is firmly attached and in safe operating condition WARNING Moving parts can amputate fingers or cause severe injuries Keep hands clothing and loose objects away from all openings ALWAYS stop engine disconnect spark plug and make sure all moving parts have come to a complete stop before removing obstructions clearing debris or servicing unit DO NOT start or operate unit unless all guards and protective covers are properly assembled to unit NEVER reach into any opening while the engine is running Moving parts may not be visible through openings A WARNING Check fuel system for leaks due to fuel tank damage especially if the unit is dropped If damage or leaks are found do not use unit otherwise serious personal injury or property damage may occur Have unit repaired by an autho rized servicing dealer before using Emission CONTROL EXHAUST amp EVAPORATIVE EPA 2010 and Later and or C A R B TIE
28. es combustion heat away from the engine Overheating and engine seizure can occur when Air intakes are blocked preventing cooling air from reaching the cylinder Dust and grass build up on the outside of the cylinder This build up insulates the engine and prevents the heat from leaving Removal of cooling passage blockages or cleaning of cooling fins is considered Normal Maintenance Any failure attributed to lack of maintenance is not warranted Remove spark plug lead 2 Remove air cleaner cover 3 Remove muffler cover screw and muffler cover A 4 Remove 2 engine cover screws and engine cover B 0 65 mm 0 026 in PRo ATTACHMENT SERIES OPERATOR S MANUAL 1 9 IMPORTANT DO NOT use a metal scraper to remove dirt from the cylinder fins 5 Use brush to remove dirt from the cylinder fins 6 Remove grass and leaves from the grid between the recoil starter and fuel tank 7 Assemble components in reverse order EXHAUST SYSTEM Spark Arrestor Screen Level 2 Tools Required Cross Head Screwdriver 4mm Hex Wrench Soft Metal Brush Parts Required Spark Arrestor Screen Gasket 1 Remove muffler cover screw and muffler cover A 2 Place piston at Top Dead Center TDC to prevent carbon dirt from entering cylinder 3 Remove spark arrestor screen B gasket C and exhaust guide D from muffler body
29. for string head installation and maintenance instructions All SB Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are designed to fit COMMERCIAL APPLICATION 1 YEAR WARRANTY All Chain Saws QuikVent Saws and Cut Off Saws for commercial institutional agricultural industrial or income producing use will be covered by this limited warranty for one 1 year from the date of purchase 2 YEAR WARRANTY All other units for commercial institutional agricultural industrial or income producing use will be covered by this limited warranty for two 2 years from the date of purchase EXCEPTIONS For two stroke engine powered products the electronic ignition module flexible drive cables SRM solid drive shafts and TC tines are warranted for the life of the product on parts only Cutting attachments such as but not limited to bars chains sprockets blades and nylon trimmer heads for commercial institutional agricultural industrial rental or income producing will be covered for failures due to defects in material or workmanship for a period of 30 days from original product purchase date Any misuse from contact with concrete rocks or other structures is not covered by this warranty ECHO s Rapid Loader String Head carries a lifetime warranty on the line locking system parts only no labor Refer to your operator s manual for string head installation and maintenance instructi
30. intain good blood circulation by performing vigorous arm exercises during frequent work breaks and also by not smoking Limit the hours of operation Try to fill each day with jobs where operating the trimmer or other hand held power equipment is not required Ifyou experience discomfort redness and swelling of the fingers followed by whitening and loss of feeling consult your physician before further exposing yourself to cold and vibration PRo ATTACHMENT SERIES OPERATOR S MANUAL Repetitive Stress Injuries It is believed that overusing the muscles and tendons of the fingers hands arms and shoulders may cause soreness swelling numbness weakness and extreme pain in those areas Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury RSI An extreme RSI condition is Carpal Tunnel Syndrome CTS which could occur when your wrist swells and squeezes a vital nerve that runs through the area Some believe that prolonged exposure to vibration may contribute to CTS CTS can cause severe pain for months or even years To reduce the risk of RSI CTS do the following Avoid using your wrist in a bent extended or twisted position In stead try to maintain a straight wrist position Also when grasping use your whole hand not just the thumb and index finger Take periodic breaks to minimize repetition and rest your hands Reduce the speed and force with which
31. may result Do not store your unit for a prolonged period of time 30 days or longer without performing protective storage mainte nance which includes the following 1 Store unit in a dry dust free place out of the reach of children with drive shaft housing in an upright or horizontal position to prevent grease leakage A DANGER Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark Place the stop switch in the OFF position Remove the spark plug and pour 7 cc 1 4 oz of fresh clean two stroke engine oil into the cylinder Remove accumulation of grease oil dirt and debris through the spark plug hole tromroxiedor orum A Place a clean cloth over the spark plug hole Perform all periodic lubrication and services that are B Pull the recoil starter handle 2 3 times to distribute required the oil inside the engine Tighten all the screws and nuts Observe the piston location through the spark plug hole Pull the recoil starter handle slowly until the piston reaches the top of its travel and leave it Drain the fuel tank completely and pull the recoil here starter handle several times to remove fuel from the carburetor Install the spark plug do not connect ignition cable SPECIFICATIONS Displacement Exhaust Fuel Tank Capacity Starter System Clutch Drive Shaft Idle Speed
32. may result Use an approved fuel container DO NOT smoke near fuel DO NOT allow flames or sparks near fuel Fuel tanks cans may be under pressure Always loosen fuel caps slowly allowing pressure to equalize NEVER refuel a unit when the engine is HOT or RUNNING DO NOT fill fuel tanks indoors ALWAYS fill fuel tanks outdoors over bare ground DO NOT overfill fuel tank Wipe up spills immediately Securely tighten fuel tank cap and close fuel container after refueling Inspect for fuel leakage If fuel leakage is found do not start or operate unit until leakage is repaired Move at least 3m 10 ft from refueling location before starting the engine Mixing Instructions nas 1 Fill an approved fuel container with half of the required amount of Fuel to Oll Mix 50 1 Ratio 2 Add the proper amount of 2 stroke oil to gasoline Cos a as pa COLORE 3 Close container and shake to mix oil with gasoline 4 Add remaining gasoline close fuel container and remix IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions Some states may require the use of automatic fuel shut off containers to reduce fuel spillage After use DO NOT store a unit with fuel in its tank Leaks can occur Return unused fuel to an approved fuel storage container IMPORTANT Stored fuel ages Do not mix more fuel than you expect to use in thirty 30 days ninety 90 days when a fuel Storage Fuel
33. ne Stop Switch Move stop switch button A backward to STOP position A WARNING If engine does not stop when stop switch is moved to STOP posi tion close choke COLD START position to stall engine Have your ECHO dealer repair stop switch before using unit again 16 MECHO MAINTENANCE A WARNING Moving parts can amputate fingers or cause severe injuries Keep hands clothing and loose objects away from all openings Always stop engine disconnect spark plug and make sure all moving parts have come to a complete stop before removing obstructions clearing debris or servicing unit Allow unit to cool before performing service Wear gloves to protect hands from sharp edges and hot surfaces Your ECHO trimmer is designed to provide many hours of trouble free service Regular scheduled maintenance will help your trimmer achieve that goal If you are unsure or are not equipped with the necessary tools you may want to take your unit to an ECHO Service Dealer for maintenance To help you decide whether you want to DO IT YOURSELF or have the ECHO Dealer do it each maintenance task has been graded If the task is not listed see your Echo dealer for repairs SKILL LEVEL Level1 Easy to do Common tools may be required Level2 Moderate difficulty Some specialized tools may be required ECHO offers REPOWER Maintenance Kits and Parts to make your maintenance job easier MAINTENANCE INTERVALS COMPONENT
34. ons All SB Series and PRO ATTACHMENT SERIES Split Shaft attachments carry the same warranty duration as the units they are designed to fit RENTAL APPLICATION 90 DAYS WARRANTY Units for rental use will be covered against defects in material and workmanship for a period of 90 days from the date of purchase ECHOS liability under the Lifetime coverage is limited to furnishing parts specified under the PRODUCT WARRANTY PERIOD section of this warranty statement for Life free of charge for a period of ten 10 years after the date of the complete unit s final production 28 MECHO PURCHASED REPAIR PARTS SHORT BLOCKS AND ACCESSORIES 90 day residential or non income producing warranty 30 day commercial institutional agricultural industrial income producing or rental application warranty ATTENTION TWO STROKE ENGINE POWER PRODUCT OWNERS This ECHO two stroke engine power product is a quality engineered unit which has been manufactured to exact tolerances to provide superior performance To help ensure the performance of the unit it is required to use two stroke oil which meets the ISO L EGD Standard per ISO CD 13738 and JASO M345 FC FD Standards ECHO Power Blend Two Stroke Oil is a premium two stroke oil specifically formulated to meet ISO L EGD ISO CD 13738 and JASO M345 FC FD Standards The use of two stroke oils designed for other applications such as for outboard motors or lawnmowers can result in severe engine damage and
35. pacity Damage caused by pump or sprayer running dry pumping or spraying caustic or flammable materials or lack of or broken strainers Additional damage to parts or components due to continued use after operational problem or failure occurs Should operational problem or failure occur the product should not be used but delivered as is to an authorized ECHO servicing dealer Itis a dealer s and or customer s responsibility to complete and return the warranty registration card supplied with your ECHO product or by visiting WWW ECHO USA COM Your receipt of purchase including date model and serial number must be maintained and presented to an authorized ECHO servicing dealer for warranty service Proof of purchase rests solely with the customer Some states do not allow limitations on how long an implied warranty lasts so the above limitations may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so you may also have other specific legal rights which vary from state to state This limited warranty is given by ECHO Incorporated 400 Oakwood Rd Lake Zurich IL 60047 DISCLAIMER OF IMPLIED WARRANTIES This limited warranty is in lieu of all other expressed or implied warranties including any warranty of FITNESS FOR A PARTICULAR PURPOSE OR USE and any implied warranty of MERCHANTABILITY otherwise applicable to this product ECHO and its affiliated companies shall not be liable for any
36. rvicing dealer for warranty repairs within the applicable warranty period and arrange for pick up or return of your unit after the repairs have been made For your nearest authorized ECHO servicing dealer call ECHO s Dealer Referral Center at 1 800 432 ECHO or you can locate an ECHO servicing dealer at WWW ECHO USA COM Should you require assistance or have questions concerning ECHO s Warranty Statement you can contact our Consumer Product Support Department at 1 800 673 1558 or contact us through the web at WWW ECHO USA COM PRODUCT WARRANTY PERIOD RESIDENTIAL APPLICATION 5 YEAR WARRANTY All units for residential or non income producing use will be covered by this limited warranty for five 5 years from date of purchase EXCEPTIONS For two stroke engine powered products the electronic ignition module flexible drive cables SRM solid drive shafts and TC tines are warranted for the life of the product on parts only Cutting attachments such as but not limited to bars chains sprockets blades and nylon trimmer heads for residential or non income producing use will be covered for failures due to defects in material or workmanship for a period of 60 days from original product purchase date Any misuse from contact with concrete rocks or other structures is not covered by this warranty ECHO s Rapid Loader String Head carries a lifetime warranty on the line locking system parts only no labor Refer to your operator s manual
37. s and exclusions THIS LIMITED WARRANTY IS ONLY APPLICABLE TO ECHO PRODUCTS SOLD BY AUTHORIZED ECHO DEALERS IT IS EXTENDED TO THE ORIGINAL PURCHASER ONLY AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS Repair parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period Any damage caused by improper installation or improper maintenance is not covered by this warranty All parts or products replaced under warranty become the property of ECHO Inc This warranty is separate from the Emission control warranty statement supplied with your new product Please consult the Emission Control Warranty Statement for details regarding emission related parts For a list of Authorized ECHO Dealers refer to WWW ECHO USA COM or call 1 800 432 ECHO OWNER S RESPONSIBILITY To ensure trouble free warranty coverage it is important that you register your ECHO equipment on line at WWW ECHO USA COM or by fill ing out the warranty registration card supplied with your unit Registering your product confirms your warranty coverage and provides a direct link if we find it necessary to contact you The owner shall demonstrate reasonable care and use and follow preventative maintenance storage fuel and oil usage as prescribed in the operator s manual Should a product difficulty occur you must at your expense deliver or ship your ECHO unit to an authorized ECHO se
38. uipment SORE was designed built and equipped to conform with applicable EPA and C A R B emissions standards and that your equipment SORE is free from defects in material and workmanship that would cause it to fail to conform with applicable requirements for 2 years or the length of the ECHO Inc warranty whichever is longer The warranty period begins on the date the product is purchased by an end user HOW WILL A COVERED PART BE CORRECTED If there is a defect in a part covered by this warranty any ECHO Inc Authorized Service Dealer will correct the defect You will not have to pay anything to have the part adjusted repaired or replaced This includes any labor and diagnosis for warranted repairs performed by the dealer In addition engine parts not expressly covered under this warranty but whose failure is a result of a failure of a covered part will be warranted WHAT PARTS ARE COVERED Any applicable emission related part not scheduled for required maintenance will be repaired or replaced within the warranty period The repaired or replaced part will be warranted for the remaining ECHO Inc warranty period Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated above Any such part repaired or replaced under warranty will be warranted for the remaining ECHO Inc warranty period Any emission related part scheduled for replacement during required maint
39. ully depressed and pull recoil starter starter handle rope until en gine starts and runs Release throttle trigger and allow unit to warm up at idle for several minutes NOTE If engine does not start with choke in Run position after 5 pulls repeat instructions 2 5 6 Throttle Trigger After engine warm up gradually depress throttle trigger to increase engine RPM to operating speed PRo ATTACHMENT SERIES OPERATOR S MANUAL 1 5 STARTING WARM ENGINE The starting procedure is the same as Cold Start except DO NOT close the choke and do not depress throttle trigger to wide open position A WARNING The attachment should not move at idle otherwise serious personal injury may result NOTE If attachment moves readjust carburetor according to Carburetor Adjustment instructions in this manual or see your ECHO Dealer Stop Switch Move stop switch button lever A away from the STOP position Purge Bulb Pump purge bulb C until fuel is visible and flows freely in the clear fuel tank return line Pump bulb an additional 4 or 5 times Recoil Starter Lay the unit on a flat area and keep movable attachment parts clear of all obstacles Rapidly pull recoil starter handle rope D until engine fires NOTE If engine does not start after 5 pulls use Cold Start Procedure STOPPING ENGINE 1 Throttle Release throttle and allow engine to return to idle before shutting off engi
40. ustrations may include optional equipment and acces sories and may not include all standard equipment SAFETY PRo ATTACHMENT SERIES OPERATOR S MANUAL 3 MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION Throughout this manual and on the product itself you will find safety alerts and helpful informational messages pre ceded by symbols or key words The following is an explanation of those symbols and key words and what they mean to you A DANGER The safety alert symbol accompanied by the word DANGER calls attention to an act or condition which WILL lead to serious personal injury or death if not avoided A WARNING The safety alert symbol accompanied by the word WARNING calls attention to an act or condi tion which CAN lead to serious personal injury or death if not avoided This symbol means the specific action shown is prohibited Ignoring these prohi bitions can result in serious or fatal injury S CIRCLE AND SLASH SYMBOL NOTE This enclosed message provides tips for use care and maintenance of the unit A CAUTION The safety alert symbol accompanied by the word CAUTION calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided IMPORTANT The enclosed message provides information neces sary for the protection of the unit INTERNATIONAL SYMBOLS Symbol Symbol Symbol form shape POTE a E Symbol
41. will void your two stroke engine limited warranty THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY Lack of lubrication or engine failure due to the use of two stroke oils that do not meet the ISO L EGD ISO CD 13738 and JASO M345 FC FD Standards Engine problems due to inadequate lubrication caused by failure to use an ISO L EGD compliant and JASO M345 FC FD registered oil will void the two stroke engine limited warranty ECHO Power Blend Two Stroke Oil meets the ISO L EGD and JASO M345 EC ED Standard Emission related parts are covered for 5 years residential use or 2 years commercial use regardless of two stroke oil used per the statement listed in the EPA or California Emission Defect Warranty Explanation Damage caused by use of gasohol containing methanol wood alcohol or gasoline containing less than 89 octane Only use gasoline which contains 89 octane or higher Gasohol which contains a maximum 10 ethanol grain alcohol or 15 MTBE methyl tertiary butyl ether is also approved The prescribed mixing ratio of gasoline to oil is listed on the ECHO oil label and covered in your operator s manual Engine damage caused by use of ether or any starting fluids Damage caused by tampering with engine speed governor or emission components or running engines above specified and recommended engine speeds as listed in your operator s manual Operation of the unit with improperly maintained removed cutting shield or removed damaged air filter D
42. you do the repetitive move ment Doexercises to strengthen the hand and arm muscles Immediately stop using all power equipment and consult a doctor if you feel tingling numbness or pain in the fingers hands wrists or arms The sooner RSI CTS is diagnosed the more likely permanent nerve and muscle damage can be prevented A WARNING Do not operate this product indoors or in inadequately ventilated areas Engine exhaust contains poisonous emissions and can cause serious injury or death Read the Manuals Provide all users of this equipment with the Operator s Manual and Safety Manual for instructions on Safe Operation Clear the Work Area Spectators and fellow workers must be warned and children and animals prevented from coming nearer than 15 m 50 ft while the unit is in use Keep a Firm Grip Hold the front and rear handles with both hands with thumbs and fingers encircling the handles Keep a Solid Stance Maintain footing and balance at all times Do not stand on slippery uneven or unstable surfaces Do not work in odd positions or on lad ders Do not over reach Avoid Hot Surfaces Keep exhaust area clear of flammable debris Avoid contact during and immediately after operation RATO 6 MECHO EQUIPMENT A WARNING Use only ECHO approved attachments for Pro Attachment Series models Serious injury may result from the use of a non approved attachm
Download Pdf Manuals
Related Search