Echo HC-2410 User's Manual
Contents
1. T T T T I INSPECT REPLACE C CLEAN IMPORTANT Time intervals shown are maximum Actual use and your experience will determine the frequency of required maintenance All recommendations to replace are based on the finding of damage or wear during inspection 1 Replacement will be required for Commercial use after 600 hours For Consumer use cleaning every 6 months is required 2 Apply 1 2 pumps of ECHO LUBE every 10 hours 20 AIR FILTER Level 1 Tools required 25 or 30 mm 1 or 2 in medium bristle paint brush Parts required 90008REPOWER AIR 8 FUEL FILTER KIT 1 Close choke Cold Start Position This prevents dirt from entering the carburetor throat when the air filter is removed Brush accumu lated dirt from the air cleaner area 2 Remove the air cleaner cover Clean and inspect the element for damage If element is fuel soaked and very dirty replace 3 If element can be cleaned and reused be certain it still fits the cavity in the air cleaner cover 1s installed with the original side out NOTE Carburetor adjustment may be needed after air filter cleaning replacement FUEL FILTER Level 1 Tools required 203 234 mm 8 10 in length of wire with one end bent into a hook Clean rag funnel and an approved fuel container Parts required 90008 REPOWER AIR amp FUEL FILTER KIT WARNING DANGER Fuelis VERY flammable Use extreme care2. Any failure attributed to lack of maintenance is not warranted HEDGE CLIPPER OPERATOR S MANUAL 0 65 mm 0 026 in 21 22 WELHO 1 Remove starter and disconnect the throttle cable end from the carburetor 2 Remove the two screws that retain the engine cover Lift the engine erp oc TEE cover A from the engine and lay aside A ome T 1 f il 7 a ALL d The throttle cable remains assembled to the engine cover and the spark plug lead and grommet remain installed kig IMPORTANT DO NOT use a metal scraper to remove dirt from the cylinder fins 3 Use the wooden stick or brush to remove dirt from the cylinder fins 4 Remove grass and leaves from the starter air intake grid NOTE When installing the engine cover A be certain the tab of the metal deflector shield is in the slot of the cover EXHAUST SYSTEM Spark Arrestor Screen Level 2 Tools required 3mm Allen wrench Soft metal brush Parts Required Screen P N 14586240630 Gasket Lid P N 14586642031 1 Remove engine cover A See Cleaning Cooling System pages 20 amp 21 for step by step instructions 2 Place piston at Top Dead Center TDC to prevent carbon dirt from entering cylinder 3 Remove spark arrestor screen cover screen holder gasket D and screen E from muffler body 4 Clean carbon deposits from screen and muffler components 5
3. ee HEDGE CLIPPER pa __1 Warranty Registration Card ERES SAFETY MANUAL EMISSION MODELS __1 Plastic Bag T Wrench Bottle 2 6 oz 2 Cycle Oil 1 Blade Cover The updated emissions information for your unit is Emission CONTROL EPA Phase 2 IMPORTANT ENGINE INFORMATION j ENGINE FAMILY 2EHXS 0214RA DISPLACEMENT 21 2cc An Emission Control Label is located on the engine The ENGINE COMPLIANCE PERIOD 300 Hours emission control system for these engines is EM Engine THIS ENGINE MEETS U S EPA PH2 EMISSION Modification REGULATIONS FOR SMALL NONROAD ENGINES REFER TO OWNER S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS E gt comm v9 Thisisan EXAMPLE ONLY information on label varies by engine family ECHO CONSUMER PRODUCT SUPPORT If you require assistance or have questions concerning the application operation or maintenance of this product you may call the ECHO Consumer Product Support Department at 1 800 673 1558 from 8 30am to 4 30 pm Central Standard Time Monday through Friday Before calling please know the model and serial number of your unit to help your Consumer Product Support Representative
4. N 99922202800 English version only is available at a cost of 5 00 from ECHO INC or any authorized ECHO dealer The video overviews safety precautions and proper operating tech niques and is supplemental to the Safety Manual Read and understand the Safety Manual for complete information on safe operation 12 MECHO SPECIFICATIONS MODEL HC 1500 1E HC 1600 1E HC 2000 1E HC 1500 2E Length 960mm 1133mm 990mm 1030mm 1280mm 37 8 in 44 6 in 39 0 in 40 6 in 50 4 in Width 225mm 240mm 240mm 240mm 240mm 8 9 in 9 4 in 9 4 in 9 4 in 9 4 in Height 190mm 200mm 230mm 210mm 210mm 7 5 in 7 9 in 9 1 in 8 3 in 8 3 in Weight dry 4 4 kg 5 3 kg 5 2 kg 5 2 kg 5 2 kg 9 7 lb 11 7 lb 11 4 lb 11 4 lb 11 4 lb Type of Engine Air cooled two stroke single cylinder gasoline engine Displacement 21 2 66 21 206 21 2 23 6 23 6 1 29 Cu in 1 29 Cu in 1 29 cu in 1 44 cu in 1 44 cu in Stroke 26 0 mm 26 0 mm 26 0 mm 26 0 mm 26 0 mm 1 02 1 02 1 02 in 1 02 in 1 02 in Exhaust System Spark Arrestor Muffler Ignition System Flywheel Magneto Capacitor discharge ignition Spark Plug BPM 7A Gap 0 65 mm 0 026 in Fuel Oil Ratio 50 1 Ratio using ECHO Hi Performance two stroke air cooled engine oil Gasoline 89 Octane Unleaded Do not use fuel containing methyl alcohol more than 10 ethyl alcohol or 15 MTBE LEN ECHO Hi Performance two stroke air cooled eng
5. ZURICH IL 60047 1564 WWW echo usa com SUPPLEMENT TO OPERATOR S MANUAL PART NUMBER X7532248103 89861105635 FOR MODEL HC 1500 1600 2000 2400 2410 SUPLEMENTO DEL MANUAL DEL OPERADOR NUMERO DE PIEZA X7532248103 89861105635 PARA LOS MODELO HC 1500 1600 2000 2400 2410 MECHO This supplement applies to the models and serial numbers shown below Hedge Clipper Operator s Manual Models HC 1500 Type 1E Serial Number 001001 amp Up HC 1500 Type 2E Serial Number 672901 amp Up HC 1600 Type 1E Serial Number 526701 amp Up HC 2000 Type 1E Serial Number 523201 amp Up HC 2400 2410 Type 1E Serial Number 001001 amp Up HC 2400 2410 Type 2E Serial Number 001001 amp Up Este suplemento se aplica a los modelos y a los n meros de serie mostrados abajo Recortador De Cerca De Arbustos Manual del Operador Modelos HC 1500 Tipo 1E N meros de serie 001001 y siguientes HC 1500 Tipo 2E N meros de serie 672901 y siguientes HC 1600 Tipo 1E N meros de serie 526701 y siguientes HC 2000 Tipo 1E N meros de serie 523201 y siguientes HC 2400 2410 Tipo 1E N meros de serie 001001 y siguientes HC 2400 2410 Tipo 2E N meros de serie 001001 y siguientes SUP22203532 99922203532 01 02 Your unit now includes the following package contents CONTENTS __1 Hedge Clipper Assembly TRE e Operators Manual E ECHO INCORPORATED __1 Safety Manual EMISSIONS AND WARRANTY 1 Warranty Statement
6. move During acceleration depress gradually for best operating technique BLADES Double reciprocating blades mounted to a blade support bar Models HC 1500 HC 1600 are double sided blades meaning they are capable of cutting on either side of the blade All other models are single sided AIR CLEANER Contains replaceable filter element PRIMER BULB Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the carbure tor for starting Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line Pump bulb an additional 4 or 5 times CHOKE The choke control lever is located on the top of the choke case Move to COLD START to close the choke for Cold Starting Move to RUN position to open choke RECOIL STARTER HANDLE Pull handle slowly until recoil starter engages then quickly and firmly DO NOT pull rope all the way out or allow the handle to snap back damage to the starter will occur FUEL TANK Contains fuel and fuel filter FUEL TANK CAP Covers and seals fuel tank opening SPARK PLUG Provides spark to ignite fuel mixture MUFFLER SPARK ARRESTOR The muffler controls the exhaust noise while the spark arrestor prevents hot glowing particles of carbon from leaving the muffler where they could possibly start a fire BLADE COVER Used to cover blades during transportation or storage Remove blade cover before using unit SAFETY VIDEO Notincluded with unit P
7. plug Clean and adjust replace Carburetor Adjust Cooling system plugged Clean Spark arrestor screen Clean plugged WARNING DANGER Fuel vapors are extremely flammable and may cause fire and or explosion Never test for ignition spark by grounding spark plug against cylinder otherwise serious personal injury may result 30 MECHO STORAGE Long Term Storage over 30 days Do not store your unit for a prolonged period of time 30 days or longer without performing protective storage maintenance which includes the following 1 Store unit in a dry dust free place out of the reach of children WARNING DANGER Do not store in enclosure where fuel fumes may accumulate or reach an open flame or spark HC 1500 2 Place the stop switch A in the OFF position 3 Remove accumulation of grease oil dirt and debris from exterior of unit 4 Perform all periodic lubrication and services that are required 5 Tighten all the screws and nuts 6 Drain the fuel tank completely and pull the recoil starter handle several times to remove fuel from the carburetor 7 Remove the spark plug and pour 1 4 oz 1 2 tablespoon of fresh clean two stroke engine oil into the cylinder through the spark plug hole A Place a clean cloth over the spark plug hole B Pull the recoil starter handle 2 3 times to distribute the oil inside the engine C Observe the piston location through the spark plug hole Pull the recoil han
8. when the engine is operating Inspect hand guard for damage Replace if damaged or missing Check that the blade assembly is firmly attached and in safe operating condition Dull loose or damaged blades should not be used ECHO INC will not be responsible for the failure of cutting devices or accessories which have not been tested and approved by ECHO for use with this unit Symbol Symbol Symbol form shape description application Symbol form shape description application Carburetor adjustment High speed mixture Carburetor adjustment Idle speed Do not operate clos er than 15 M 50 ft from electrical haz ards Primer bulb Wear slip resistant foot wear Keep bystanders at least 4 5 meters 15 feet away HEDGE CLIPPER OPERATOR S MANUAL FUEL WARNING DANGER Fuelis VERY flammable Use extreme care when mixing storing or handling or serious personal injury may result Use an approved fuel container DO NOT smoke near fuel DO NOT allow flames or sparks near fuel Fuel tanks cans may be under pressure Always loosen fuel caps slowly allowing pressure to equalize e NEVER refuel a unit when the engine is HOT NEVER refuel a unit with the engine running DO NOT fill fuel tanks indoors ALWAYS fill fuel tanks outdoors over bare ground Securely tighten fuel cap after refueling Inspect for fuel leakage If fuel leakage is found do not start or operate unit until leakage
9. LROPE Lay the hedge clipper on a flat clear area and pull the recoil starter handle D until engine fires 5 OPENCHOKE RUN Move choke B to the RUN OPEN position Restart engine if necessary and allow unit to warm up at idle for several minutes WARNING DANGER The blades should not move at idle If blades move readjust carburetor according to Carburetor Adjustment instructions in this manual or see your ECHO Dealer otherwise serious personal injury may result 6 After engine warm up gradually depress throttle trigger to increase engine RPM to operating speed STARTING WARM ENGINE The starting procedure is the same as Cold Start except DO NOT close the choke WARNING DANGER The blades should not move at idle If blades move readjust carburetor according to Carburetor Adjustment instructions in this manual or see your ECHO Dealer otherwise serious personal injury may result 1 STOPSWITCH START RUN Move stop switch A away from the STOP position 2 START Pull Rope Lay the hedge clipper on a flat clear area and pull the recoil starter handle D until the engine fires NOTE If engine does not start after 5 pulls use Cold Start Procedure 18 MECHO STOPPING ENGINE 1 RELEASETHROTTLE Allow engine to idle for a minute 2 STOP SWITCH STOP Move stop switch A to STOP position WARNING DANGER If engine does not stop when stop switch is moved to STOP position clos
10. MECHO Hedge Clipper Operator s Manual MODELS HC 1500 Serial Number 001001 999999 HC 1500 Type 2E Serial Number 001001 672900 HC 1600 Serial Number 001001 999999 HC 1600 Type 1E Serial Number 001001 526700 HC 2000 Serial Number 001001 999999 HC 2000 Type 1E Serial Number 001001 523200 HC 2400 Serial Number 001001 999999 HC 2410 Serial Number 001001 999999 WARNING DANGER A WARNING A The muffler or catalytic muffler The engine exhaust from this and surrounding cover may become product contains chemicals known extremely hot to the State of California to cause Always keep clear of exhaust and muffler area cancer birth defects or other otherwise serious personal injury may occur reproductive harm WARNING DANGER Read rules for safe operation and all instructions carefully ECHO provides this Operator s Manual and a Safety Manual Both must be read and understood for proper and safe operation X7502248103 89861105635 12 00 2 MECHO INTRODUCTION Welcome to the ECHO family This ECHO product was designed and manufactured to provide long life and on the job dependability Read and understand this manual and the SAFETY MANUAL you found in the same package You will find both easy to use and full of helpful operations tips and SAFETY messages WARNING DANGER Read rules for safe operation and instructions carefully ECHO provides an Operator s Manual and a Safety Manual Bot
11. Proper Clothing Wear snug fitting durable clothing e Pants should have long legs shirts with long sleeves e DONOT WEAR SHORTS DONOTWEARTIES SCARFS JEWELRY Wear protective hair covering to contain long hair Wear sturdy work shoes with nonskid soles e DONOT WEAR OPEN TOED SHOES DONOTOPERATE UNITBAREFOOTED Wear no slip heavy duty work gloves Hot Humid Weather Heavy protective clothing can increase operator fatigue which may lead to heat stroke Delay heavy work until temperature drops X ag 30 9 19 LE HEDGE CLIPPER OPERATOR S MANUAL SAFE OPERATION Determine Operation Area Do not operate this product indoors or in inadequately ventilated areas Review the area to be trimmed Look for hazards that could contribute to unsafe conditions Spectators and fellow workers must be warned and children animals prevented from coming nearer than 4 5 m 15 ft while the Hedge Clipper is in use Provide all users of this equipment with the Operator s Manual and instructions for Safe Operation Operation Use Proper Clothing amp Equipment Before starting the unit equip yourself and any other person working within the 4 5 m 15 ft Safety Zone with the required Protective Equipment and clothing Keep a Solid Stance Maintain footing and balance at all times Do not stand on slippery uneven or unstable surfaces Do not work in odd posit
12. RATOR S MANUAL Read and understand this manual before operation Keep manual in a safe location for future reference i e operation maintenance storage and specifications SAFETY MANUAL Read and understand this manual before operation Keep manual in a safe location of safe operating techniques POWER HEAD Factory Assembled to the gear housing assembly Includes the Engine Clutch Fuel System Ignition System and Recoil Starter REAR HANDLE HC 1500 1600 Contains the Stop Switch Throttle Lockout and Throttle Trigger LEFT HAND REAR HANDLE HC 2000 2400 2410 Contains the Stop Switch Throttle Lockout and Throttle Trigger FRONTHANDLE GUARD HC 1500 1600 Comfortable textured finish provides anti slip grip for front hand Guard protects hand from the blades Warning decals are located on guard HC 2000 2400 and HC 2410 Right Hand Handle Rubber anti slip grip guard protects hand from the blades Warning decals are located on guard STOPSWITCH HC 1500 TOGGLE SWITCH located on the left side of the rear handle Move switch UP tt RUN DOWN to STOP HC 1600 HC 2000 2400 2410 SLIDE SWITCH mounted on top of the left hand rear handle Move switch FOR WARD to RUN BACK to STOP THROTTLE TRIGGER LOCKOUT This lever must be depressed before Throttle Trigger can be activated THROTTLE TRIGGER Spring loaded to return to idle when released Trigger Lockout must be depressed fully before Throttle Trigger will
13. Replace screen if it is cracked plugged or has holes burned through 6 Assemble components in reverse order NOTE When installing the engine cover be certain the tab of the metal deflector shield is in the slot of the cover HEDGE CLIPPER 2 3 OPERATOR S MANUAL CARBURETOR ADJUSTMENT Emission Models Level 2 Tools required Screwdriver with 2mm blade width Tachometer ECHO P N 99051130017 Parts required None NOTE Every unit is run at the factory and the carburetor is set in compliance with EPA Phase 1 and California Emission Regulations In addition the carburetor is equipped with HI A and LO B needle adjustment limiters that prevent settings outside acceptable limits 1 Before adjusting the carburetor clean or replace the air filter and spark arrester screen 2 Start engine and run for several minutes to reach operating tempera N A L ture 522 y J i 3 Stop engine Turn HI A speed needle CCW counter clockwise to stop Turn LO B speed needle midway between full CCW and CW clockwise stops 4 Idle Speed Adjustment Start engine and turn idle C speed adjustment screw CW until the blades begin to move then turn the screw CCW until blades stop moving Turn screw CCW an additional 1 4 turn 5 Accelerate to full throttle for 2 3 seconds to clear excess fuel from engine then return to idle Accelerate to full throttle to check for smooth transition from idle to full throttle If engin
14. Some states may require the use of automatic fuel shut off containers to reduce fuel spillage Contact your ECHO dealer for ordering information After Refueling Wipe any spilled fuel from the unit Move at lease 3 m 10 ft from refueling location before starting the engine After use e DO NOT store a unit with fuel in its tank Leaks can occur Return unused fuel to an approved fuel storage container Storage Fuel storage laws vary by locality Contact your local government for the laws affecting your area As a precaution store fuel in an approved air tight container Store in a well ventilated unoccu pied building away from sparks and flames Do not store fuel longer than 30 days IMPORTANT WT F S Stored fuel ages Do not mix more fuel than you expect to use in 4 5 6 7 thirty 30 days ninety 90 days when a fuel stabilizer is added 1112 13 14 18 19 20 21 25 26 27 28 IMPORTANT Stored two stroke fuel may separate ALWAYS shake fuel container thoroughly before each use HEDGE CLIPPER 1 5 OPERATOR S MANUAL EQUIPMENT CHECK Before operation a complete check of the unit must be performed e Check unit for loose missing nuts bolts and screws Tighten and or replace as needed Inspect fuel lines tank and area around carburetor for fuel leaks DO NOT operate unit 1f leaks are found Never adjust blades when the engine is operating Inspect hand guard for damage Replace if damaged or mi
15. afety decals on your unit The complete unit illustration found in the DESCRIPTION section will help you locate them Make sure the decals are legible and that you understand and follow the instructions on them If a decal cannot be read a new one can be ordered from your ECHO dealer See PARTS ORDERING instructions for specific information ALL HEDGE CLIPPER MODELS P N 505000270 HC 2000 HC 2400 HC 2410 ONLY HC 1500 HC 1600 ONLY P N 505000290 4 MECHO INTERNATIONAL SYMBOLS Symbol Symbol Symbol form shape description application Symbol form shape description application EQUIPMENT Before operation a complete check of the unit must be performed Carburetor adjustment Read and understand Fuel and oil mixture 4 Low speed mixture owners manual Wear eyes ears and Safety Alert head protection Finger Severing Avoid all power lines This unit is not Emergency stop insulated against electrical current DO NOT smoke Wear hand protec near fuel Plan retreat path tion Use two handed from falling objects Ignition Engine choke Ignition DO NOT allow control ON OFF flames or sparks near fuel Do not operate without guards in place Chain lubrication Check unit for loose missing nuts bolts and screws Tighten and or replace as needed Inspect fuel lines tank and area around carburetor for fuel leaks DO NOT operate unit if leaks are found Never adjust blades
16. d DO NOT allow blade to over heat 4 Models HC 1500 HC 1600 Assemble blade stiffenerusing new blade nuts if required Tighten bolts and nuts then loosen bolt 1 2 turn to allow free blade movement 5 Lubricate blades See Blade Lubrication Instructions on page 24 IMPORTANT Blades should only be removed and reinstalled by an Authorized ECHO Servicing Dealer otherwise premature wear or internal damage may occur HEDGE CLIPPER 2 9 OPERATOR S MANUAL TROUBLESHOOTING Engine starts hard Engine does not start Engine Fuel at No fuel at Fuel strainer clogged Clean Cranks carburetor carburetor Fuel line clogged Clean Carburetor See your ECHO dealer Fuel at No fuel at cylinder cylinder Carburetor See your ECHO dealer Muffler wet Fuel Mixture is too rich Open choke with fuel Clean replace air filter Adjust carburetor See your ECHO dealer Spark at end No spark Stop switch off Turn switch on of plug wire at end of Electrical problem See your ECHO dealer plug wire Interlock switch See your ECHO dealer Spark at plug No spark Spark gap incorrect Adjust 0 65mm 0 026in at plug Covered with carbon Clean or replace Fouled with fuel Clean or replace Spark plug defective Replace plug Internal engine problem See your ECHO dealer does not crank Dies or accelerates poorly Air filter dirty Clean or replace Fuel filter dirty Replace Fuel vent plugged Replace Spark
17. dle slowly until the piston reaches the top of its travel and leave it there 8 Install the spark plug do not connect ignition cable HEDGE CLIPPER 3 1 OPERATOR S MANUAL NOTES SERVICING INFORMATION PARTS Genuine ECHO Parts and ECHO REPOWER Parts and Assemblies for your ECHO products are available only from an Authorized ECHO Dealer When you do need to buy parts always have the Model Number and Serial Number of the unit with you You can find these numbers the engine housing For future reference write them the space provided below Model No SN SERVICE Service of this product during the warranty period must be performed by an Authorized ECHO Service Dealer For the name and address of the Authorized ECHO Service Dealer nearest you ask your retailer or call 1 800 432 ECHO 3246 Dealer information is also available on our Web Site When presenting your unit for Warranty service repairs proof of purchase is required ECHO CONSUMER PRODUCT SUPPORT If you require assistance or have questions concerning the application operation or maintenance of this product you may call the ECHO Consumer Product Support Department at 1 800 673 1558 from 8 00 am to 5 00 pm Central Standard Time Monday through Friday Before calling please know the model and serial number of your unit to help your Consumer Product Support Representative WARRANTY REGISTRATION You may register your Echo equipment using the warran
18. e Tuning Requires Accurate Tachometer 1 Start engine and allow to warm to operating temperature minimum 2 3 minutes while varying engine speed from idle to full throttle 2 Always begin fine tuning with LO B needle a Lean drop off With engine idling turn LO needle slowly CW in to lean drop off point RPM will increase then abruptly drop off Note this position 1 b Rich drop off With engine idling slowly turn LO B needle CCW out to rich drop off point RPM will increase then gradually slow and drop off Note this position 2 c Final setting Set needle at mid point between lean rich drop off points 3 d Turn needle 1 8 turn CCW out making mixture slightly richer 4 3 HI speed adjustment Adjust HI A needle with tachometer Refer to Wide Open Throttle RPM settings listed in Specifications on page 12 4 Check idle speed and reset if necessary If tachometer is available idle speed should be set to the specifications found on page 12 Specifications of this manual WARNING DANGER When carburetor adjustment is completed blades should not move at idle otherwise serious personal injury may result LUBRICATION Blades Level 1 Tools required Cleanrag 25 or 50mm 1 or 2 in medium bristle paint brush Parts Required 20W Engine Oil lubrication 50 50 mixture of kerosene and 20W oil cleaning WARNING DANGER Hedge Clipper Blades are very sharp Wear glov
19. e choke COLD START position to stall engine Have your ECHO dealer repair stop switch before using hedge clipper again MAINTENANCE Your ECHO Hedge Clipper is designed to provide many hours of trouble free service Regular scheduled maintenance will help your Hedge Clipper achieve that goal If you are unsure or are not equipped with the necessary tools you may want to take your unit to an ECHO Service Dealer for maintenance To help you decide whether you want to DO IT Y OUR SELF or have the ECHO Dealer do it each maintenance task has been graded If the task is not listed see your ECHO Service Dealer for repairs SKILL LEVEL Levell Easy to do Most required tools come with unit Level2 Moderate difficulty Some specialized tools may be required Level3 Experience required Specialized tools are required ECHO recommends the unit be returned to your ECHO dealer for servicing ECHO offers REPOWER Maintenance Kits and Parts to make your maintenance job easier Just below each task heading are listed the various part numbers required for that task See your ECHO dealer for these parts HEDGE CLIPPER 1 9 OPERATOR S MANUAL MAINTENANCE INTERVALS Maintenance Before Every Component System Use Refuel pem eem CEI raiment mM comm pm _ come feo _ ne mem comes fem Rope pem
20. e hesitates turn LO B needle CCW an additional 1 8 turn and repeat acceleration Continue adjusting until smooth acceleration results 6 Check HI speed RPM at W O T Wide Open Throttle HI speed RPM should be set to specifications found on page 12 Specifica tions of this manual 7 Check idle speed and reset if necessary If a tachometer is available idle speed should be set to the specifications found on page 12 Specifications of this manual WARNING DANGER When carburetor adjustment is completed blades should not move at idle otherwise serious personal injury may result 24 UUELHE CARBURETOR ADJUSTMENT Non Emissions Models Level 2 Tools required Screwdriver with 2mm blade width Tachometer ECHO P N 99051130017 Parts Required None Idle Speed Adjustment Turn idle speed adjustment screw C CW clockwise until blades begin to move then turn screw out CCW counter clockwise until blades stop moving Turn screw out CCW an additional 1 4 turn WARNING DANGER Blades must not move when unit is idling otherwise serious personal injury may result Basic Setting 1 Stop engine and turn both LO B and HI A needles in CW until they stop and are lightly seated IMPORTANT DO NOT over tighten needles Forcing them to tighten will damage the carburetor 2 Turn needles out CCW HC 1500 LO B 1 1 4 turns HI A 1 1 2 turns Others LO B 1 1 4 turns HI A 1 3 8 turns Fin
21. es to protect hands 1 Disconnect spark plug wire from spark plug 2 Brush loose debris from blade and coat both sides of blade with the 50 50 cleaning mixture 3 Allow cleaning mixture to soften the remaining gummy residue then wipe it from the blade 4 Apply clean oil to the entire length of the blade Be certain the blade bolts are lubricated 5 Wipe excess oil from the blade before putting the unit back in service HEDGE CLIPPER OPERATOR S MANUAL 25 26 Gear Box Assembly Level 2 Tools required 3mm Hexagon wrench Grease Gun Parts Required Gear Box Gasket HC 2400P N 61041401260 HC 15002EP N 61041406560 Others P N 61041405360 ECHO LUBE 8 oz P N 91014 or Lithium Based Grease HC 1500 Type 1 Type LE 1 Clean debris and dirt from gear box area Remove the six 6 socket head cap screws retaining the gear box cover plate 2 Remove cover plate and discard gasket 3 Add grease as required DO NOT over fill Leave room for the grease to expand during operation HC 1600 2000 All Level 1 Tools required 13mm Open End Grease Gun Parts required ECHO LUBE 8 P N 91014 or Lithium Based Grease 1 Clean dirt from filler plug area and remove plug 2 Carefully pump grease into hole DO NOT force grease Too much pressure will force grease past seals and cause damage Qa gt Reid 3 Wipe excess grease from gear box and replace the filler pl
22. h must be read and understood for proper and safe operation THE OPERATOR S MANUAL contains specifications and information for operation starting stopping maintenance storage and assembly specific to this product AEDHU Hedge Clipper Gprrator s Manual MODELS Piel w Suit Nonie amp thy RCHA Senat O MACH amp TC Type 1 Ft Hint Tip BC 380 Typo HE amar dh MIR Tp THE SAFETY MANUAL pum aon explains possible hazards involved with the use of Hedge Clippers and what measures you should take to make their use safer TABLE OF CONTENTS DOPPIE EOI eie 18 Introduction Maintenance The Operator s Manual Skill Levels The Safety Manual Maintenance 5 aaa ore 19 Manual Safety Symbols and Important Information Air Filter Fuel Filter oy 3 Spark Plug International Symbols Cooling System Equipment Exhaust System Carburetor Adjustment Emission Personal Condition and Safety Equipment Carburetor Adjustment Non Emission Sale 7 Tudanca E 25 Extended Operation Extreme Conditions Blade Stiffener Remove Install 27 Deser DUON oli 9 Sharpening Blades EE OUI 9 Troubleshooting Emissions Control Si aE 12 Servicing Information Model
23. ine oil Fuel Tank Capacity 0 3 lit 0 5 lit 0 5 lit 0 5 lit 0 5 lit 10 1 fl oz 17 0 fl oz 17 0 fl oz 17 0 fl oz 17 0 fl oz Starter System Automatic Recoil Starter Clutch Centrifugal Type Gear Case Ratio 1 5 88 1 5 88 1 5 88 1 5 13 TE 15 13 TE 1 3 9 2E 1 3 9 2E Cutter Double Double Edge Double Edge Single Edge Single Edge Single Edge Reciprocating Blade Length 573mm 721mm 750mm 750mm 994mm 22 6 in 28 4 in 29 5 in 29 5 in 39 1 in Height 21mm 21mm 24mm 24mm 24mm 0 83 in 0 83 in 0 94 in 0 94 in 0 94 in Idle Speed RPM 3000 Wide Open Throttle RPM 11 000 12 000 HC 2400 1E HC 2410 1E HC 2400 2E HC 2410 2E HEDGE CLIPPER 1 3 OPERATOR S MANUAL ASSEMBLY HC MODELS ARE PRE ASSEMBLED IN THE BOX Tools Required None Parts Required None PRE OPERATION FUEL Fuel Requirements Gasoline Use 89 Octane 1 mid grade or higher gasoline known to be good quality Gasoline may contain up to 15 MTBE methyl tertiary butyl ether Gasohol containing methyl wood alcohol is NOT approved Two Stroke Oil A two stroke engine oil meeting ISO L EGD ISO CD 13738 and J A S O FC Standards must be used Echo brand Premium 50 1 oil meets these standards Engine problems due to inadequate lubrication caused by failure to use an ISO L EGD andJ A S O FC certified oil such as Echo Premium 50 1 Two stroke Oil will void the two stroke engine warranty Emiss
24. ion related parts only are covered for two years regardless of two stroke oil used per the statement listed in the EPA Phase I California Emission Defect Warranty Explanation IMPORTANT Echo Premium 2 Stroke Oil may be mixed at 50 1 ratio for application in all Echo engines sold in the past regardless of ratio specified in those manuals Mixing Instructions 1 Fill an approved fuel container with half of the required amount of gasoline Add 2 stroke oil to gasoline Close container and shake to mix oil with gasoline Add remaining gasoline and remix Install fuel container cap and wipe any spilled fuel from con tainer and surrounding area id OS 14 MECHO Handling Fuel WARNING DANGER Fuelis VERY flammable Use extreme care when mixing storing or handling or serious personal injury may result Use an approved fuel container e DO NOT smoke near fuel DO NOT allow flames or sparks near fuel Fuel tanks cans may be under pressure Always loosen fuel caps slowly allowing pressure to equalize NEVER refuel a unit when the engine is HOT NEVER refuel a unit with the engine running DO NOT fill fuel tanks indoors ALWAYS fill fuel tanks outdoors over bare ground Securely tighten fuel cap after refueling Inspect for fuel leakage If fuel leakage is found do not start or operate unit until leakage is repaired IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions
25. ions or on ladders Do not over reach Keep a Firm Grip Hold the front and rear handles with both hands with thumbs and fingers encircling the handles Avoid Hot Surfaces e During operation the complete unit especially the power head muffler area and cutting attachment may become very hot too hot to touch Avoid contact during and immediately after operation 8 MECHO EXTENDED CONDITIONS Vibration and Cold It is believed that a condition called Raynaud s Phenomenon which affects the fingers of certain individuals may be brought about by exposure to vibration and cold Exposure to vibration and cold may cause tingling and burning sensations followed by loss of color and numbness in the fingers The following precautions are strongly recommended because the minimum exposure which might trigger the ailment is unknown Keep your body warm especially the head neck feet ankles hands and wrists Maintain good blood circulation by performing vigorous armexercises during frequent work breaks and also by not smoking Limit the hours of operation Try to fill each day with jobs where operating the trimmer or other hand held power equipment is not required f you experience discomfort redness and swelling of the fingers followed by whitening and loss of feeling consult your physician before further exposing yourself to cold and vibration Repetitive Stress Injuries I
26. is repaired IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions Some states may require the use of automatic fuel shut off containers to reduce fuel spillage Contact your ECHO dealer for ordering information After Refueling e Wipe any spilled fuel from the unit Move at lease 3 m 10 ft from refueling location before starting the engine After use e DO NOT store a unit with fuel in its tank Leaks can occur Return unused fuel to an approved fuel storage container PERSONAL CONDITION AND SAFETY EQUIPMENT WARNING DANGER Hedge Clipper users risk injury to themselves and others if the hedge clipper is used improperly and or safety precautions are not followed Proper clothing and safety gear must be worn when operating a hedge clipper 6 MECO Physical Condition Your judgment and physical dexterity may not be good if you are tired or sick if you are taking medication if you have taken alcohol or drugs Operate unit only if you are physically and mentally well Eye Protection Eye protection that meet ANSI Z87 1 or CE requirements must be worn whenever you operate the Hedge Clipper Hand Protection Wear no slip heavy duty work gloves to improve your grip on the handles Gloves also reduce the transmission of machine vibration to your hands Hearing Protection Wear hearing protection ECHO recommends wearing hearing protec tion whenever unit is used
27. or missing parts Use the contents list to check for missing parts CONTENTS 1 Hedge Clipper Assembly 1 Operators Manual 1 Safety Manual 1 Warranty Statement 1 Warranty Registration Card Plastic Bag T Wrench 8 mm x 10mm Open end Wrench Bottle 2 6 oz 2 Cycle Oil BladeCover MECHO Operator s Manual HEDGE CLIPPER OPERATOR S MANUAL EMISSION CONTROL Emissions Models The emission control system for this engine is EM Engine Modification IMPORTANT ENGINE INFORMATION ENGINE FAMILY TEHO21UB24RA DISPLACEMENT 21 2cc THIS ENGINE MEETS U S EPA PHI AND 1995 1999 CALIFORNIA EMISSION REGULATIONS FOR ULGE ENGINES REFER TO OWNER S MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS xc0mmz comm o Emission Control Label located on Engine EXAMPLE ONLY information on label varies by FAMILY MECHO ECHO INCORPORATED EMISSIONS ANO WARRANTY STATEMENTS FOR UNITED STATES EMISSION MODELS TAR INSCIPCKIN GAF ANTLA LIMITADA wo priscpal de E barra Pru Pest alc Chastain jarima 11 Hamarraman Croas dm Coma EL RESUMEN DE DE ECHO 9 10 MECHO MECHO Hedge Clipper Operator s Manual VIDEO HC 1500 1600 9 4 7 8 14 5 13 E 18 SA ED 12 HC 2000 2400 2410 10 11 12 13 14 15 16 17 18 19 20 HEDGE CLIPPER 1 1 OPERATOR S MANUAL OPE
28. s HC 1500 1600 2000 2400 24 10 Assembly Pre Operation Warranty Card Fuel 13 Additional or Replacement Manuals a EquipmentCheck us citi ass cect tee ascos 15 Manual Ordering Instructions Determine Operation Area Supplement Instructions Operation Page 9 Supplement Starting Cold Engine Starting Warm Engine Specifications descriptions and illustrative material in this literature are as accurate as known at the time of publica tion but are subject to change without notice Illustra tions may include optional equipment and accessories and may not include all standard equipment CopyRight 2000 By Echo Incorporated All Rights Reserved HEDGE CLIPPER OPERATOR S MANUAL MANUAL SAFETY SYMBOLS AND IMPORTANT INFORMATION Throughout this manual and on the product itself you will find safety alerts and helpful information messages preceded by symbols or key words The following is an explanation of those symbols and key words and what they mean to you This symbol accompanied by the words WARNING and DANGER calls attention to an act or condition that can lead to serious personal injury to operator and bystanders The enclosed message provides information necessary for the protec The circle with the slash symbol means whatever is shown s tion of the unit within the circle is prohibited NOTE This enclosed message provides tips for use care and maintenance of the unit SAFETY DECALS Locate these s
29. ssing Check that the blade assembly is firmly attached and in safe operating condition Dull loose or damaged blades should not be used DETERMINE OPERATION AREA Before starting the unit equip yourself and fellow workers in the 4 5 m 15 ft safety zone with the required protective equipment and clothing Review the area to be trimmed Look for hazards that could contribute to unsafe conditions Spectators children and animals must be prevented from coming nearer than 4 5 m 15 Ft while the Hedge Clipper is in use 16 OPERATION Provide all users of this equipment with the Operator s Manual instructions for Safe Operation Before starting the unit equip yourself and any other person working within the 4 5 m 15 ft Safety Zone with the required Protective Equipment and clothing During operation the complete unit especially the gear box may become very hot too hot to touch Avoid contact during and immediately after operation Do not operate this product indoors or in inadequately ventilated areas STARTING COLD ENGINE 1 STOPSWITCH START RUN Move stop switch A away from the STOP position 2 CHOKE COLDSTART Move choke B to the Cold Start CLOSED position 3 PRIMER PUMPBULB Pump primer bulb C until fuel is visible and flows freely in the clear fuel tank return line Pump bulb an additional 4 or 5 times HEDGE CLIPPER 1 7 OPERATOR S MANUAL 4 START PUL
30. t is believed that overusing the muscles and tendons of the fingers hands arms and shoulders may cause soreness swelling numbness weakness and extreme pain in those areas Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury RSI An extreme RSI condition is Carpal Tunnel Syndrome CTS which could occur when your wrist swells and squeezes a vital nerve that runs through the area Some believe that prolonged expo sure to vibration may contribute to CTS CTS can cause severe pain for months or even years To reduce the risk of RSI CTS do the following Avoid using your wrist in a bent extended or twisted position Instead try to maintain a straight wrist position Also when grasping use your whole hand not just the thumb and index finger Take periodic breaks to minimize repetition and rest your hands Reduce the speed and force with which you do the repetitivemove ment Do exercises to strengthen the hand and arm muscles Immediately stop using all power equipment and consult a doctor if you feel tingling numbness or pain in the fingers hands wrists or arms The sooner RSI CTS is diagnosed the more likely permanent nerve and muscle damage can be prevented DESCRIPTION The ECHO product you purchased has been factory pre assembled for your convenience After opening the carton check for damage Immedi ately notify your retailer or ECHO Dealer of damaged
31. ty registration card or register on line at www echo usa com Registering provides a direct link between you and ECHO if we find it necessary to contact you ADDITIONAL OR REPLACEMENT MANUALS DEALER Call 1 800 432 ECHO 1 800 432 3246 www echo usa com CONSUMER PRODUCT SUPPORT 1 800 673 1558 8 5 Mon Fri C S T Safety Manuals in English Spanish or English French are available free of charge from your ECHO dealer or at www echo usa com Operator s and Parts Manuals are available by Downloading free from www echo usa com Purchasing from your Echo Dealer Sending a check or money order for 2 00 per Parts Catalog or 1 50 per Operator s Manual made payable to ECHO INCORPORATED State on a sheet of paper the model number and serial number of the ECHO unit you have part number of the manual if known your name and address and mail to address above Safety Videos are available from your Echo dealer A 5 00 shipping charge will be required for each video Available Parts Catalog Parts Lists HC 1500 Type IE Serial Number001001 UP P N99922202758 HC 1500 Type2E Serial Number001001 UP P N99922202898 HC 1600 Type IE Serial Number001001 UP P N99922202759 HC 2000 Type IE Serial Number001001 UP P N 99922202760 HC 2400 2410TypelE SerialNumber001001 UP P N 99922202761 HC 2400 2410 Type2E Serial Number001001 UP P N99922202762 MEGHO ECHO INCORPORATED 400 Oakwoop RoAD LAKE
32. ug f c HEDGE CLIPPER OPERATOR S MANUAL HC 1500 2E HC 2400 2410 Level 1 Tools required Grease Gun Cleanrag Parts required ECHO LUBE 8 oz P N 91014 or Lithium Based Grease 1 Clean dirt from the grease fitting 2 Carefully pump grease into fitting DO NOT force grease Too much pressure will force grease past seals and cause damage Ta 74 CUN BLADE STIFFENER REMOVE INSTALL Level 2 Tools required 2 13mm Open End Parts Required None WARNING DANGER Hedge Clipper blades are very sharp Wear gloves to protect hands 1 Disconnect spark plug wire from spark plug 2 Hold blade bolt head under blade assembly Remove blade locknut from top side turning counter clockwise 3 Repeat step 2 for remaining blade nuts NOTE Locking ability of Hedge Clipper blade nuts will diminish each time they are removed Replace blade nuts if threading resistance is not felt when installing locknuts 27 28 MECHO SHARPENING BLADES Level 3 Tools required Flat file Screwdriver Parts required None WARNING A DANGER Hedge Clipper Blades are very sharp Wear gloves to protect hands 1 Disconnect spark plug wire from spark plug 2 Models HC 1500 HC 1600 Remove blade stiffener See Blade Stiffener Remove Install on page 26 3 File each edge carefully Follow the original shape of the blade IMPORTANT If a power grinder is use
33. when mixing storing or handling 1 Use aclean rag to remove loose dirt from around fuel cap and empty fuel tank 2 Use the fuel line hook to pull the fuel line and filter from the tank 3 Remove the filter from the line and install the new filter SPARK PLUG Level 2 Tools required T wrench Feeler gauge Soft metal brush Parts required 90064REPOWER Tune Up Kit 1 Remove spark plug and check for fouling worn and rounded center electrode 2 Clean the plug or replace with a new one DO NOT sand blast to clean Remaining sand will damage engine 3 Adjust spark plug gap by bending outer electrode 4 Tighten spark plug to 145 155 kg cm 125 135 in lb COOLING SYSTEM CLEANING Level 2 Tools required 3 Allen wrench 4 mm Allen wrench Pointed Wood Stick Cross head Screwdriver Parts required None if you are careful IMPORTANT To maintain proper engine operating temperatures cooling air must pass freely through the cylinder fin area This flow of air carries combustion heat away from the engine Overheating and engine seizure can occur when e Air intakes 1 the crankcase are blocked preventing cooling air from reaching the cylinder e Dust and grass build up on the outside of the cylinder This build up insulates the engine and prevents the heat from leaving Removal of crankcase cooling passage blockages or cleaning of cooling fins 15 considered Normal Maintenance
Download Pdf Manuals
Related Search