Dynex DX-TVM112 User's Manual
Contents
1. ASSEMBLY GUIDE For either wood stud or concrete wall installations Safety information and specifications Tools needed i Package contents Installation instructions 2 DX TVM112 Safety information and specifications Safety information and specifications IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS CAUTION Do not use this product for any purpose not explicitly specified by Dynex Improper installation may cause property damage or personal injury If you do not understand these directions or have doubts about the safety of the installation contact Customer Service or call a qualified contractor Dynex is not responsible for damage or injury caused by incorrect installation or use The weight of your TV must not exceed 50 Ibs 22 7 kg The wall must be capable of supporting five times the weight of your TV and wall mount combined This product contains small items that could be a choking hazard if swallowed Keep these items away from young children Tools needed You will need the following tools to assemble your new TV wall mount Level Edge to edge stud i finder Pencil Phillips screwdriver 7 32 5 5 mm wood drill bit Socket wrench with 1 2 for wood stud wall 13 mm socket or OR adjustable wrench Hammer 3 8 9 5 mm masonry drill bit concrete only Measuring tape Package contents DX TVM112 3 ee Package contents2. Make sure that you have all the hardware necessary to assemble your new TV wall mount A Wall Plate 1 B Left TV Bracket 1 C Right TV Bracket 1 TV Hardware Bag Label Hardware Qty Label Hardware Qty M4 x 12mm D um STEW 4 L Co M6 spacers 4 M4 x 30 mm il CO lt crew 4 M Lag bolt washer 3 OTN M4 washer 4 N G M washer 4 5 16 x 2 3 4 lag bolt o ERS 3 m mu H 9 M4 spacers 4 Concrete anchor i M6 x 12 mm 4 screw screw mn M6 x 35mm K cc ceca 4 1 2 3 Ain 10 20 30 40 50 60 70 80 90 100mm 4 DX TVM112 Installation instructions Installation instructions STEP 1 Determine wall mount location Notes For more detailed information on determining where to drill your holes visit our online height finder at http mf1 bestbuy selectionassistant com index php heightfinder Your in should be high enough so your eyes are level with the middle of the screen Normally 40 to 60 inches from the ground The center of your TV will match the center of the wall plate A Before you drill holes in the wall 1 Measure the distance from the bottom of your TV to the middle half of the height of the TV This is measurement a 2 Measure the distance from the floor to where you want the bottom of the TV to be placed on the wall Keep in mind that the bottom of the TV should be placed above any furniture such as entertainment centers or TV stands The TV should also be above
3. Wall plate A Ceme Level z ze gt 6 DX TVM112 Installation instructions NN STEP 2 Option 2 Installing on a solid concrete or concrete block wall CAUTION To prevent property damage or personal injury never drill into mortar between blocks Mount wall plate e directly onto the concrete surface 1 Align the wall plate A at the height you determined in the previous step and make sure that it is level Use a pencil to mark the lag bolt hole locations 3 2 Drill pilot holes to a depth of 3 in 75 mm using a 3 8 in 9 5 mm diameter masonry drill bit 3 Insert the concrete wall anchors O into the pilot holes and use a hammer to make sure the anchors are flush with the concrete surface 4 Align the wall plate A with the anchors insert the lag bolts N through the lag bolt washers M then through the holes in the wall plate Tighten the lag bolts only until they are firm against the wall plate 9 CAUTION Avoid potential injuries or property damage DO NOT over tighten the lag bolts N Minimum solid concrete thickness 8 in 203mm Minimum concrete block size 8 x 8 x 16 in 203 x 203 x 406 mm ot we You ll need NNNNA NANANA NANNAN NNNNNNA i AE gE m N 3 OE YL EFE SSS Ln i Pencil rt 3 8 masonry 0 3 ouio 1 2 socket Wall plate A wrench Hammer Installation instructions DX TVM112 7 TTT STEP 3 Determ
4. items placed on top of the furniture like a Blu ray player or cable box This measurement is b 3 Add a b The total measurement is the height where you want the center of the wall plate to be on the wall 4 Use a pencil to mark this spot on the wall You ll need Measuring tape Pencil Installation instructions DX TVM112 5 OT STEP 2 Option 1 Installing on a wood stud wall Note Any wallboard or material covering the wall must not exceed 5 8 16 mm 1 Locate the stud Verify the center of the stud with an edge to edge stud finder 2 Align the wall plate A at the height you determined in the previous step and make sure that it is level Use a pencil to mark the lag bolt hole locations 2 on the stud centers Remove the wall plate 3 Drill pilot holes to a depth of 3 in 75 mm using a 7 32 in 5 5 mm diameter drill bit 4 Align the wall plate A with the pilot holes insert the lag bolts N through the lag bolt washers M then through the holes in the wall plate Tighten the lag bolts only until they are firm against the wall plate 4 CAUTION Avoid potential injuries or property damage e DO NOT over tighten the lag bolts N Minimum wood stud size common 51 x 102 mm 2 x 4 in nominal 38 x 89 mm 11 2 x 31 2 in Rory en x You ll need i 7 32 wood 1 2 socket wrench Edge toedge Pencil drill bit stud finder i p
5. of the following types of screws M4 x 12 mm screws D for a TV with a flat back M4 x 30 mm screws E for a TV with an irregular or obstructed back M6 x 12 mm screws I for a TV with a flat back M6 x 20 mm screws J for a TV with a flat back M6 x 35 mm screws K for a TV with an irregular or obstructed back Select from the following washers M4 washer F M6 washer G For an irregular or obstructed TV back use the following spacers M4 spacer H M6 spacer L CAUTION To avoid potential personal injuries and property damage make sure that there are adequate threads Screw fit tO secure the brackets to your TV If you encounter resistance correctly stop immediately and contact customer service Use the shortest screw and spacer combination to accommodate your TV Using hardware that is too long may damage your TV However using a screw that is too short may cause your TV to fall from the mount o G Screw is Screw is too long too short 2 Remove the screws 3 Fora flat back TV go to STEP 5 Option 1 Attaching the mounting hardware to TVs with a flat back on page 9 OR For an irregular or obstructed back go to STEP 5 Option 2 Attaching the mounting hardware to TVs with irregular or obstructed backs on page 10 Installation instructions DX TVM112 9 STEP 5 Option 1 Attaching the mounting hardware to TVs with a flat back 1 Align the left and right TV brackets B and C with the screw h
6. ate A 2 Push the bottom of the TV toward the wall until the latch mechanism clicks into place E gt HEAVY You will need assistance with this step Latched 12 DX TVM112 Installation instructions Removing the TV from the wall plate 1 Grasp the TV by the bottom edge then pull down on the locking cords and pull the bottom of the TV out from the wall 2 Release the locking cords and lift the top of the TV from the wall bracket HEAVY You will need assistance with this step Unlatched Pull down to unlatch Pull bottom away from wall then lift off the wall bracket Pa dui Ni www dynexproducts com 800 305 2204 Distributed by Best Buy Purchasing LLC 7601 Penn Ave South Richfield MN 55423 U S A 2012 BBY Solutions Inc All rights reserved DYNEX is a trademark of BBY Solutions Inc Registered in some countries All other products and brand names are trademarks of their respective owners 6907 002010 lt 02 gt 12 1056 ENGLISH
7. ine whether your TV has a flat back or an irregular or obstructed back 1 Carefully place your TV screen face down on a cushioned clean surface to protect the screen from damages and scratches 2 If your TV has a table top stand attached remove the stand See the documentation that came with your TV for instructions 3 Temporarily lay the TV brackets B and C on the back of your TV 4 Align the screw holes in the TV brackets with the mounting screw holes on your TV 5 Identify which type of back your TV may have Flat back The brackets lay flush against the back of your TV and do not block any jacks You do not need spacers when assembling the wall mount Obstructed back The brackets block one or more of the jacks on the back of your TV You will need spacers when assembling the wall mount Irregularly shaped back There is a gap between a bracket and some part of the back of your TV You will need spacers when assembling the wall mount 6 Remove the TV brackets 8 DX TVM112 Installation instructions iii SSCS STEP 4 Select screws washers and spacers 1 Select the hardware for your TV screws washers and spacers A limited number of TVs come with mounting hardware included If there are screws that came with the TV they are almost always in the holes on the back of the TV If you don t know the correct length of the mounting screws your TV requires test various sizes by hand threading the screws Select one
8. oles on the back of the TV 2 Install washers F or G and screws D I or J into the holes in the back of the TV NOTE If the hole pattern on your TV is 75 mm x 75 mm do not use the washers F or G 3 Tighten the screws until they are snug against the TV brackets Do not over tighten You ll need Screws Washers jm or pw or D 4 1 4 F 4 G or B and C TV brackets Phillips screwdriver 10 DX TVM112 Installation instructions E STEP 5 Option 2 Attaching the mounting hardware to TVs with irregular or obstructed backs 1 Align the left and right TV brackets B and C with the screw holes on the back of the TV 2 Place spacers H or L behind the TV brackets and the washers F or G over the holes in the TV bracket then insert the screws E or K through the washers TV brackets and spacers NOTE If the hole pattern on your TV is 75 mm x 75 mm do not use the washers F or G 3 Tighten the screws until they are snug against the TV brackets Do not over tighten A nth You ll need Screws Washers Spacers 1 9 C O Cp SE K 4 F a Gi HA L 4 z J Phillips screwdriver Sone chet Installation instructions DX TvM112 11 STEP 6 Mounting the TV to the wall plate 1 Place the TV brackets B and C into the slotted flanges of the wall pl
Download Pdf Manuals
Related Search