Dynasty Spas GS500 User's Manual
Contents
1. the temperature change in the desired direction After three seconds the LCD will stop flashing and display the current spa temperature Note If there is not a blower on the system an alternate panel with separate Up and Down buttons in place of a Set or Temp button may be used Simply press Up or Down where a Temp or Set button press is indicated Jets Touch the Jets button once to turn pump 1 on or off and to shift between low and high speeds if equipped If left running the low speed of the pump will automatically turn off after 4 hours and the high speed will automatically turn off after 15 minutes Blower optional on VS501 or GS501 This button is used to turn the blower on and off If left on the blower automatically turns off after 15 minutes Jets 2 optional on VS501 or GS501 If your system has a pump 2 installed instead of a blower it behaves exactly like a blower would Light Press the Light button to turn the light on and off If left on the light automatically turns off after 4 hours Balboa E a E Electronic pa Control Duplex Digital System a wO Temp Light Mode Mode is changed by pressing the Temp or Set button then pressing the Light button Standard Mode is programmed to maintain the desired temperature Note that the last measured spa temperature displayed is current only when the circ pump has been run2. V 500 501 GS500 501 Control Reference Card Circ Operation Initial Start up When your spa is first actuated it will go into Priming mode indicated by Pr Please see the M 7 Installation Instruction Manual for complete instructions on Power up and Pump Priming The Priming mode will last for less than 5 minutes press Temp or Set to skip Priming Mode and then the spa will begin to heat the spa and maintain the water temperature in the Standard mode Balboa Blower Jets Hectic Spa Controls a Your system has a 24 hour circ pump The circ pump and the ozone generator run continuously with the exception of shutting off for 30 minutes at a time in hot environments Temp Set 80 F 104 F 26 C 40 C The start up temperature is set at 1OOF 37 C The last measured temperature is constantly displayed on the LCD Note that the last measured spa temperature displayed is current only when the circ pump has been running for at least 2 minutes To display the set temperature press the Temp or Set pad once To change the set temperature press the pad a second time before the LCD stops flashing Each press of the Temp or Set pad will continue to either raise or lower the set temperature If the opposite direction is desired release the pad and let the display revert to the current water temperature Press the pad to display the set temperature and again to make
3. aler or service organization Follow action required for HL message Heating capability of the spa will not reset automatically you may press any button to reset Check water level in spa Refill if necessary If water level is okay make sure the pumps have been primed Press any button to reset or this message will automatically reset within 15 minutes If problem persists contact your dealer or service organization Follow action required for dr message Spa will not automatically reset Press any button to reset Warning Shock Hazard No User Serviceable Parts Do not attempt service of this control system Contact your dealer or service organization for assistance Follow all owner s manual power connection instructions Installation must be performed by a licensed electrician and all grounding connections must be properly installed Instruments Incorporated P N 40299 05 28 2004
4. in the heater Spa is shut down for 15 minutes g 4H Inadequate water detected in heater Displays on third occurrence of dr message Spa is shut down Action Required The control panel will be disabled until power returns Spa settings will be preserved until next power up After the circ pump has been running for 2 minutes the temperature will be displayed DO NOT ENTER THE WATER Remove the spa cover and allow water to cool Once the heater has cooled reset by pushing any button If spa does not reset shut off the power to the spa and call your dealer or service organization DO NOT ENTER THE WATER Remove the spa cover and allow water to cool At 107 F 42 C the spa should automatically reset If spa does not reset shut off the power to the spa and call your dealer or service organization No action required The pump and blower will automatically activate regardless of spa status If the problem persists contact your dealer or service organization May appear temporarily in an overheat situation and disappear when the heater cools If the problem persists contact your dealer or service organization May appear temporarily in an overheat situation and disappear when the heater cools If the problem persists contact your dealer or service organization Check water level in spa Refill if necessary If the water level is okay make sure the pumps have been primed If problem persists contact your de
5. ning for at least 2 minutes S will be displayed momentarily when you switch into Standard Mode Economy Mode heats the spa to the set temperature only during filter cycles Ec will display solid when temperature is not current and will alternate with temperature when temperature is current Sleep Mode heats the spa to within 20 F 10 C of the set temperature only during filter cycles SL will display solid when temperature is not current and will alternate with temperature when temperature is current Preset Filter Cycles The first filter cycle begins 6 minutes after the spa is energized The second filter cycle begins 12 hours later Filter duration is programmable for 2 4 6 8 hours or for continuous filtration indicated by FL The default filter time is 2 hours To program press Temp or Set then Jets Press Temp or Set to adjust Press Jets to exit programming At the beginning of each filter cycle the blower purges for 30 seconds the pump purges for 5 minutes The only effect filter duration has is 1 During the filter the circ pump never turns off and 2 In Economy and Sleep Modes heating only occurs during the filter cycle Freeze Protection If the temperature sensors detect a drop to below 44 F 6 7 C within the heater the pump and blower will automatically activate to provide freeze protection The equipment stays on until 4 minutes after the sensor
6. s detect that the spa temperature has risen to 45 F 7 2 C or higher In colder climates an optional additional freeze sensor may be added to protect against freeze conditions that may not be sensed by the standard sensors Aux freeze sensor protection acts similarly except with the temperature thresholds determined by the switch and without a 4 minute delay in turnoff See your dealer for details No message on display Power has been cut off to the spa Z Temperature unknown H H Overheat The spa has shut down One of the sensors has detected 118 F 48 C at the heater m H Overheat The spa has shut down One of the sensors has detected that the spa water is 110 F 43 C Ice Potential freeze condition detected FS cA Spa is shut down The sensor that is plugged into the Sensor A jack is not working Sh Spa is shut down The sensor that is plugged into the Sensor B jack is not working 5 m Sensors are out of balance If alternating with spa temperature it may just be a temporary condition If flashing by itself spa is shut down Hi A significant difference between temperature sensors has been detected This could indicate a flow problem E Persistent low flow problems Displays on the fifth occurrence of HL message within 24 hours Heater is shut down but other spa functions continue to run normally g r Possible inadequate water poor flow or air bubbles in detected
Download Pdf Manuals
Related Search