Dualit DCT 2 User's Manual
Contents
1. Dualit CONVEYOR TOASTER INSTRUCTION MANUAL UK 01 07 DUALIT CONVEYOR TOASTER Thank you for purchasing the Dualit Conveyor toaster This hardworking and versatile machine will provide fast and efficient toasting where large quantities of toast or toasted bread products are required IMPORTANT SAFEGUARDS CAREFULLY READ ALL THE INSTRUCTIONS BEFORE USING THE CONVEYOR TOASTER AND KEEP IN A SAFE PLACE FOR FUTURE REFERENCE e Before connecting check that the voltage on the rating label is the same as the main supply e Do not use outdoors To protect against electrical shock do not immerse any part of this product in water or other liquid or to be sprayed splashed with water Unplug from outlet or disconnect from supply when not in use Allow to cool before cleaning removing or installing parts Do not operate this appliance with a damaged cord or plug Do not allow cable to touch hot surfaces or to hang over the edge of a table or counter top When in use a fire may occur if the toaster is touching flammable material If using close to a wall ensure this is clad with a non combustible material and adheres to fire prevention regulations 1 e products must not be cooked heated in his machine e Use the correct replacement for detachable fuse Never use a plug without the fuse cover fitted Ensure replacement fuse is the same current value as the orig2. inal Replacement fuses should be approved to BS 1362 Do not leave the appliance unattended when toasting e f the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified person in order to avoid a hazard e CAUTION DO NOT OPERATE UNIT WITHOUT CRUMB TRAY AS THIS CAUSES OVERHEATING IN THE CONTROL BOX SAVE THESE INSTRUCTIONS UNPACKING amp INSPECTION INSTALLATION DCT3 Unpack the unit and components from Model DCT 3 This model is rated 4 1Kw and is connected to a permanent wired unit the shipping container This must be installed by a qualified electrician Connection parts may be required This model must not be operated from a 13 amp supply This models power must be Remove all visible packing material and supplied via an 20A all pole isolator which provides full disconnection under over those from inside the cooking chamber voltage catagory Ill conditions If a power supply cord is to be used it shall be at least HOSRN F A quick quide is included We recommend this is displayed where the machine is to PARTS amp CONTROLS be used as a reference for users We have designed the controls to be as easy to use as possible Please familiarise yourself P If any damage is discovered contact with ae before using Bread feeder guide Dualit on 01293 652 500 Crumb tray INSTALLATION DCT1 2 a f Power ON Neon Model DCT 1 2 These models are
3. nues to run and the elements have cut out check the cooling fan is running and free of dust and dirt as the heat limit switch may have tripped If the fan is dirty isolate from the power and clean with a soft brush leave for ten minutes for the toaster to cool and push the reset button to begin toasting again Allow time for the toaster to heat up again b The toaster will also overheat if the crumb tray is not in position when in use This acts as heat screen and helps protect the internal components vital to the running of the toaster Allow a clearance of 80mm from the rear of the machine and 30mm gap between machines if two or more machines are placed next to each other 4 My bread is getting stuck inside the toaster a Ensure the thickness of the bread is no thicker than 30mm or it will get stuck and May cause fire 5 Where do I position the conveyor toaster a Ensure there are no shelves or units directly above the conveyor b Allow ample clearance around the conveyor minimum 80mm at rear and 30mm at sides This ensures air can circulate around the conveyor and keep it at optimum operating temperature c Do not cover or obstruct the fan 6 My elements have gone white a Dualit conveyors use silica glass tube elements These may go white over time Deposits of starch from the bread may build up on the element This in not harmful in any way nor does it effect the toasting performance If yo
4. rated below 3kW and are connected to a normal 13 Amp 3 pin socket If a moulded on plug is not fitted or has been removed the new plug should be fitted and wired accordingly Speed controller Top element control Bottom element control Connect the green yellow wire to the Power Saver Switch terminal and the plug marked E EARTH or by the earth symbol or coloured green or green yellow Connect the blue wire to the terminal marked N NEUTRAL or coloured black Connect the brown to the terminal marked 1 LIVE or colour red Heat Limit Reset 4 Unload chute Model shown DCT 2 C OPERATION 4 TOASTING BREAD 2 TOASTING OTHER PRODUCTS Dualit conveyor toasters are equipped with a rotary power saver switch Turn clockwise or counterclockwise to obtain the following positions FULL POWER When in this position your equipment is at full power and ready to use OFF ROTARY Two off positions are provided so that a single rotation to either direction will shut the unit off STANDBY The standby position reduces the power consumption by 75 Using this position during quiet times will save electricity and keep the toaster warm Use this whenever you know the toaster is not required for the next 10 minutes When needed turn the switch to FULL POWER Recovery time is about 30 seconds The Dualit conveyor toaster is a versatile machine which can be used for toa
5. sting or warming a variety of bread products Follow the instructions to achieve best toasting results 1 Turn the power saver to FULL POWER 2 Set the conveyor speed to 5 3 The toaster is equipped with separate top and bottom heat controls For toast we recommend setting them both to 10 HIGH 4 Allow a warm up time of 5 to 10 minutes to allow the toaster to reach optimum operating temperature 5 Place a sample product on the conveyor belt to test the settings You can use the conveyor toaster to warm or toast other bread type products such as buns muffins bagels and crossiants 1 Adjust the top and bottom element temperatures to required settings Ensure any food product used with the conveyor is less than 30mm thick If larger it may get stuck inside the toaster 2 For buns and bagels and other items requiring only one side toasting set the top element to 10 High and the bottom to 5 Medium Don t forget any change to the heat setting will take a few minutes to take effect 3 Adjust the speed as in previous section to vary the browning 4 Products flip over when coming off the conveyor belt 6 For best results set both heat regulators to full and set the speed to 5 7 Vary the speed of the belt to achieve lighter or darker toasting Any change to the speed setting will take a few seconds to take effect 3 NOTE Products will toast at different speeds Adjustments of the heat con
6. trols maybe required to achieve desired results CAUTION Burgers meat products must not be cooked heated in his machine C CLEANING PROCEDURES HEAT LIMIT SWITCH RESET TROUBLESHOOTING _ To clean the conveyor belt set the power saver in the FULL POWER position turn the top and bottom heat control to the OFF position For a lightly soiled conveyor belt turn conveyor speed control to the slowest setting 2 and wipe with a damp cloth For a heavily soiled conveyor belt turn conveyor speed control to slowest setting 2 and wipe with a dry light abrasive pad After the unit cools disconnect unit from power remove interior crumb tray and clean Slide crumb tray back into position after cleaning Wipe exterior surface of unit using a damp cloth once the machine has cooled Never allow a build up of crumbs in the tray as this may cause fire Clean on a daily basis Ensure the cooling fan is clear of dust and grease CLEAN WEEKLEY Your Dualit conveyor toaster is equipped with an automatically activated heat limit switch that interrupts the heater tube connections if the ambient temperature in the control box exceeds 190 F 88 C This switch can be reset manually by pushing the red button on the bottom of the toaster CAUTION DO NOT OPERATE UNIT WITHOUT CRUMB TRAY IN PLACE THE UNIT WILL OVERHEAT AND ACTIVATE THE HEAT LIMIT SWITCH TROUBLESHOOTING gt 1 My toast is une
7. ur conveyor toaster fails within one year from date of purchase we will repair or replace it free of charge except for the elements provided e You have not misused neglected or damaged it e It has not been modified e You supply your receipt to show when you bought your toaster Elements are guaranteed for 3 months from date of purchase for parts amp labour thereafter parts only The guarantee does not affect your statutory rights If over one year contact Dualit for recommended repair agents Further advice on using your Dualit conveyor toaster and other products in the Dualit range is available from Dualit CareLine 44 0 1293 652 500 09 00 to 17 00 Monday to Friday Or email us on info dualit com CE Compliant to US 89 336 EEC EMC directive and73 23 amp 93 68 EEC LV direc DUALIT LIMITED COUNTY OAK WAY CRAWLEY WEST SUSSEX RH11 7ST TELEPHONE 44 0 1293 652 500 FACSIMILE 44 0 1293 652 555 EMAIL info dualit com Wes www dualit com
8. venly toasted a Ensure that heat regulators are set to the highest setting possible and the switch cannot turn any further Any adjustment to the heat settings will take time to settle and as such these controls should not be adjusted whilst making toast For best results set the heat regulators both to full and the speed to 5 Vary the speed to achieve desired brownness 4 2 My toast is burning or is underdone a The speed setting should be set at the half way mark this can be adjusted to taste and will take a matter of seconds to settle If toasting is too light turn conveyor speed control counter clockwise to a lower speed If toasting is too dark turn conveyor speed control clockwise to a faster speed b Allow at least 10 minutes for the conveyor to heat up and settle from switch on c If the toaster has been left on full power without bread passing through it the first slices through will burn due to the build up of heat When the toaster is in an idle period it is advised that the toaster be turned to the power setting This will prolong the life span of the elements and reduce the chances of un even toasting when used again after the idle period TROUBLESHOOTING 20 AFTER SALES SERVICE DO ADJUST THE SETTINGS WHEN MAKING TOAST ANY ADJUSTMENT REQUIRED SHOULD BE MADE WITH THE SPEED CONTROL ONLY 3 My conveyor is overheating a If the conveyor belt conti
Download Pdf Manuals
Related Search