Draw-Tite Automobile Accessories 7903 User's Manual
Contents
1. INSTALLATION OPERATION INSTRUCTIONS eS 2ORAWITE WEIGHT DISTRIBUTING HITCH SYSTEMS 7901 7902 7903 7979 DUAL SWAY CONTROL ATTACHMENT 7901 600LB WDH KIT 7902 800LB WDH KIT 7903 1200LB WDH KIT 7979 HEAD KIT NOTE When selecting a shank select the shortest unit that provides clearance with all the accessories on the tow vehicle and the trailer This will maximize weight distributing and handling characteristics DO NOT EXCEED TOWING VEHICLE MANUFACTURER S LOAD RATINGS SPRING MAX TONGUE MAX GROSS TRAILER BAR WEIGHT LB WEIGHT LB RATING WHEN USED AS A WEIGHT _ 600 600 DISTRIBUTING HITCH WITH SPRING 800 800 BARS SHOWN 4200 1200 RATING WHEN USED AS A WEIGHT CARRYING BALL MOUNT WITHOUT 7979 SPRING BARS INTRODUCTION When a trailer is hitched to a tow vehicle the tongue weight typically causes the rear of the tow vehicle to lower and the front to raise See Figure 1 LS Figure 1 The purpose of a weight distributing hitch is to remove excessive weight from the tow vehicle s rear axle and distribute it to the front wheels and the trailer wheels See Figure 2 Figure 2 SETUP DIMENSIONS 1 Line up tow vehicle and trailer on level pavement in a straight ahead position uncoupled 2 For vehicles with air springs air shocks or automatic leveling systems check vehicle owner s manual Unless otherwise specified level the vehicle with the vehicle loaded as it will be when towing Deactivate load leveli2. SOLD SEPARATELY INCLUDED IN 3645 FASTENER KIT ALSO SOLD SEPARATEL INCLUDED IN 3216 CHAIN KIT ALSO SOLD SEPARATELY Figure 4 READ ALL INSTRUCTIONS AND CHECK PACKAGE CONTENTS ASSEMBLE SYSTEM 1 Insert shank into receiver and install pin and clip See figure 4 2 Select hitch ball to match trailer coupler socket having 1 or 1 1 4 threaded shank and capacity equal to or exceeding the gross trailer weight When using a ball with a 1 shank bushing 6a must be used Attach the ball to the head assembly 2 using a lockwasher and nut 3 Assemble head to shank as shown in Figure 4 Use 6 hardened washers 6i over pin 6h initially 4 Align head assembly bolt holes to the nearest holes on shank that corresponds to a ball height approximately 1 5 2 higher than trailer coupler height H Leave fasteners loose until hookup has been adjusted 5 Tighten ball nut according to manufacturer s specs Always use a lockwasher 6 Assemble chains to spring bars as shown in Figure 4 Allow 2 3 threads to protrude below locknut See figure 5 Chain must not bind 7 Lower trailer coupler onto hitch ball and close coupler latch 8 Apply a heavy oil or wheel bearing type grease to the upper and lower trunnion pin of each spring bar assembly 7900 01APRO5C PCN7753 2005 TOWING PRODUCTS INC Litho in USA 2 9 Hold the spring bar 3 perpendicular to the shank 1 Insert the upper trunnion pin into the upper pocket
3. requirements PASSENGERS IN TRAILERS Trailers should NOT be occupied while being towed under any circumstances TRAILER LIGHT TURN SIGNALS AND ELECTRIC BRAKES Always hook up trailer lights turn signals electric brakes and break away switch connection if equipped Even for short trips REMOVE HITCH HEAD WHEN NOT TOWING Remove hitch head from towing vehicle receiver when not towing This will prevent contamination of head pockets reduce chance of striking hitch head on driveway ramps or other objects and minimize damage in event of a rear end collision 7900 01APRO5C PCN7753 2005 TOWING PRODUCTS INC Litho in USA 5
4. allowing remaining free links to fall down to the outside of the trailer frame See figure 9 3 There must be at least 5 links between the lift unit and the spring bar This is necessary for proper operation of the spring bars during turns See figure 9 If there will be less than 5 links between the lift unit and spring bar the angle of the head assembly 2 must be increased The trailer must be uncoupled and the upper bolt removed from the head assembly The head assembly is then pivoted down and an additional washer is added underneath the pin See figure 4 Reassemble CAUTION FAILURE TO CONNECT THE SPRING BAR CHAIN CORRECTLY AND PROVIDE AT LEAST 5 LINKS BETWEEN LIFT UNIT AND SPRING BAR CAN RESULT IN DAMAGE TO THE LIFT UNIT FIGURE 10 SHOWS INCORRECT SPRING BAR CHAIN HOOK UP Use handle to raise lift unit WARNING Keep clear of all moving parts Insert spring clip on lift unit Repeat for opposite spring bar using same number of links between hook and spring bar Retract trailer tongue jack so hitch is now carrying the full trailer weight Noose VEHICLES WITH SELF ADJUSTING AND OR AUTOMATIC LEVEL CONTROL SUSPENSIONS Some of the newer vehicles may be equipped with some form of automatic leveling system and require special adjustment of the weight distributing system Please check vehicle owners manual for recommended usage of weight distributing hitches on these vehicles 7900 01APRO5C PCN7753 2005 TOWING PRODUCTS INC Litho i
5. at ball lightly with grease such as Draw Tite Hitch Ball Lubricant P N 6639 7900 01APRO5C PCN7753 2005 TOWING PRODUCTS INC Litho in USA 4 WARNINGS FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH VEHICLE CRASH AND OR PROPERTY DAMAGE COUPLED BALL HEIGHT SHOULD NEVER BE GREATER THAN UNCOUPLED BALL HEIGHT Front wheel overload and loss of rear wheel traction can result This can lead to unstable handling reduced braking ability and a tendency to jackknife when turning USE EXTREME CAUTION WHEN BACKING UP AND TURNING DO NOT ALLOW TOW VEHICLE AND TRAILER TO MANEUVER INTO A JACKKNIFE POSITION Components of the hitch and sway control if applicable may be forced into damaging contact If a jackknife maneuver has occurred examine all towing system components for damage or loosening immediately Repair or replace any damaged components before resuming towing DO NOT TOW MULTIPLE TRAILERS Towing multiple trailers may cause severe instability loss of control and structural failure DO NOT ATTEMPT TO HOOK UP OR TOW WITH A FRONT WHEEL DRIVE VEHICLE WITH THE REAR WHEELS REMOVED This will cause severe instability loss of control and structural failure TOWING TIPS DRIVING Good habits for normal driving need extra emphasis when towing The additional weight affects acceleration and braking and extra time should be allowed for passing stopping and changing lanes Signal well before a maneuver to l
6. et other drivers know your intentions Severe bumps and badly undulating road can damage your towing vehicle hitch and trailer and should be negotiated at a slow steady speed IF ANY PART OF YOUR TOWING SYSTEM BOTTOMS OUT OR IF YOU SUSPECT DAMAGE MAY HAVE OCCURRED IN ANY OTHER WAY PULL OVER AND MAKE A THOROUGH INSPECTION CORRECT ANY PROBLEMS BEFORE RESUMING TRAVEL CHECK YOUR EQUIPMENT Periodically check the condition of all your towing equipment and keep it in top condition TRAILER LOADING Proper trailer loading is important Heavy items should be placed close to the floor near the trailer axle The load should be balanced side to side and firmly secured to prevent shifting Tongue weight should be about 10 15 percent of the gross trailer weight for most trailers Too low a percentage of tongue weight often produces a tendency to sway SWAY CONTROLS A sway control can help minimize the effects of sudden maneuvers wind gusts and buffeting caused by other vehicles Use of a sway control is recommended for trailers with large surface areas such as travel trailers and for trailers with low tongue weight percentage TIRE INFLATION Unless specified otherwise by the towing vehicle or trailer manufacturer tires should be inflated to their maximum recommended pressure TOWING VEHICLE AND TRAILER MANUFACTURERS RECOMMENDATIONS Review the owner s manual for your towing vehicle and trailer for specific recommendations capacities and
7. he number of chain links between lift unit and spring bar 2 There must be at least 5 links between the lift unit and the spring bar This is necessary for proper operation of the spring bars during turns If there are less than 5 links the angle of the head assembly must be increased 3 When the desired settling is achieved mark the hooked chain link with paint for future reference NOTE SURGE BRAKES usually require a small amount of fore aft movement for their actuating mechanisms to function To avoid restricting movement it may be necessary to increase the number of chain links between the lift units and the spring bars CHECK TRAILER AND OR SURGE BRAKES OPERATING INSTRUCTIONS FOR SPECIAL REQUIREMENTS REGARDING WEIGHT DISTRIBUTING HITCHES TIGHTEN HEAD FASTENERS 1 Tighten 3 4 bolts and locknuts to 250 Ib ft Tighten setscrew to 50 Ib ft CHECK ALL CONNECTIONS BEFORE TOWING 1 Check the following pin and clip securing shank to receiver head to shank fasteners ball nut coupler latch lift unit bolt safety chains lights and turn signals and braking system including breakaway switch LUBRICATION 1 TRUNNIONS SHOULD BE LUBRICATED EACH TOWING DAY FAILURE TO DO SO WILL RESULT IN EXCESSIVE POCKET AND TRUNNION WEAR Use a heavy oil or grease such as Draw Tite Hitch Ball Lubricant P N 6939 2 Excessive oil dirt and grit should be wiped out of pockets whenever trailer is uncoupled 3 Clean hitch ball and coupler socket Co
8. n USA 3 ADJUST HOOKUP IF NECESSARY A weight distributing system is properly set up and coupled when the tow vehicle has settled with the front wheel opening F at the original uncoupled dimension measured and slightly lower in the rear R See Figure 11 Figure 11 e This will assure the front wheel load remains unchanged This results in good handling and the desired load on the rear axle and trailer axle e The front of the vehicle should never settle more than the rear See Figure 12 If necessary increase the number of chain links between lift unit and spring bar If there are no more links the angle of the head assembly 2 must be decreased The trailer must be uncoupled and the upper bolt 6e removed from the head assembly The head assembly is then pivoted up and a washer 6i is removed from underneath the pin 6h See figure 1 Reassemble e 34 1 ton and or long wheelbase vehicles will typically settle with the front wheel opening F at the original dimension to 1 2 higher than original This is will still allow acceptable front wheel loads good handling and the desired load on the rear axle and trailer axle e If the rear suspension sags too much additional leveling is required The front wheel opening F may ONLY be settled lower than the original dimension IF the rear wheel opening R has settled by a greater amount At least 1 Figure 12 1 If additional leveling is required decrease t
9. ng system before coupling trailer and adjusting spring bars 3 Measure and record uncoupled height on front and rear wheel openings to pavement and level trailer coupler height See figure 3 Figure 3 F R 7900 01APRO5C PCN7753 2005 TOWING PRODUCTS INC Litho in USA 1 N 3a b c 5b 3d e f PART PART REF NUMBER QTY DESCRIPTION REF NUMBER QTY DESCRIPTION 1 See Catdog 1 Shank Assembly ox Separately 6 3645 1 Fastener Ki 2 799 1 Head Assembly t Together 6a 3233 1 Bushing ye TO 1 Ball Shank Dual Sway Covina Attachment 6b 1040 1 Hitch 2a 3640 1 Set Screw 5 8 11 Grade 5 6c 1128 1 Clip Hair Pin 3a 6648 2 Spring Bar Trunnion Ass y 600 6d 1376 018 1 Bolt 3 4 10 X 4 1 2 Grade 5 3b 6649 2 Spring Bar Trunnion Ass y 800 6e 1376 020 1 Bolt 3 4 10 x o Grade 5 3c 6650 2 Spring Bar Trunnion Ass y 1200 6f 1410 2 Locknut 3 41 3d 6652 2 Spring Bar 600 6g 3232 2 Conical Thed Washer 3 4 3e 6654 2 Spring Bar 800 6h 3305 1 Pin 3f 6656 2 Spring Bar 1200 6i 3306 8 Washer Hardened 3g 6638 2 Trunnion Cast 600 800 7 3216 1 Chain Kit 3h 6639 2 Trunnion Cast 1200 7a 3217 2 Chain 3i 664 2 Pin Slotted Spring 600 800 7b 1436 2 U Bolt 3j 6645 2 Pin Slotted Spring 1200 Te 1243 4 Locknut 3 8 16 4 6634 1 Handle 7d 1160 006 4 Flat Washer 3 8 5 6636 2 Lift Unit Assembly 5a 3388 2 Set Screw Square Head 5b 2867 2 Clip INCLUDED IN 6648 6649 6650 SPRING BAR Weyer ALSO
10. of the head assembly See figure 6 Rotate the spring bar so the lower trunnion pin passes through the entrance slot in the lower pocket of the head assembly 2 TO 3 THREADS Figure 5 Figure 6 Figure 7 10 Position lift units on trailer A frame If trailer tongue consists of a single tube or other narrow member a pole tongue adapter Draw Tite P N 3280 must be used Hold spring bar chain vertical Center lift units with chain See figure 7 11 Turn 1 2 13 x 3 1 2 bolt until it contacts the frame Then tighten 2 turn with wrench DO NOT OVER TIGHTEN NOTE Optional mounting holes are provided for trailers that do not permit use of 13 bolt See figure 8 CONSULT TRAILER FRAME MANUFACTURER FOR APPROVAL PRIOR TO DRILLING HOLES 3 8 hardware is recommended whether it is self tapping or nut and bolt 5 LINKS LESS THAN MINIMUM 5 LINKS OPTIONAL MOUNTING HOLES ie CHAIN AND INCORRECT LIFT UNIT BINDS Figure 8 Figure 9 Figure 10 SPRING BAR CHAIN CONNECTION 1 With lift unit in raised position pull straight up firmly on spring bar chain Note which link is closest to chain hook See figure 7 Countdown 2 links and that link will used for hook up NOTE BEFORE OPERATING LIFT UNIT RAISE BUMPER OF TOW VEHICLE WITH THE TRAILER TONGUE JACK APPROXIMATELY ONE INCH THIS WILL REDUCE SPRING BAR TENSION AND MAKE LIFT UNIT OPERATION EASIER 2 Lower lift unit Attach upper end of chosen chain link to lift unit hook while
Download Pdf Manuals
Related Search