Dixon ZTR 311 User's Manual
Contents
1. ORTANT Perform SAFETY CHECKS after making any repairs or adjustments 1 After reassembly while seated on the mower attempt to start the engine with the mower deck engaged Engine should not start If engine does start return the mower to an Authorized Dixon Dealer for adjustment or repair 2 Disengage the mower deck and start engine With the operator in the normal seated position engage mower deck and remove weight from the seat The engine should stop If the engine doesn t stop when operator rises from the seat return the mower to Authorized Dixon Dealer for adjustment or repair 3 Engage then disengage mower blade in each cutting height Insure that blade disengages and comes to a stop within 5 seconds in each height position If blade does not disengage properly repeat belt adjustment procedure or contact your Authorized Dixon Dealer Removing The Mower Blade Secure the blade P N 6013 from turning Observe the blade position when removing Remove the blade bolt from the center of the blade remove the blade flange P N 2837 blade P N 2406 and spacer P N 2829 WARNING Sharp edges on the blade can cause injury Caution should be exercised when service is required on the blade Parking Brake Adjustment Remove the body as described above Tighten nut on brake rod P N 2533 Located in front of the transaxle on each side just enough to prevent brake from slipping when engaged CAU2. TECHNICAL DATA BROCHURE ZTR 308 amp 311 DATE 8 86 Re IMPORTANT READ OPERATOR S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS PAGE 1 of 6 Seat Adjustment Loosen bolts on sliding brackets under each side of the seat slide seat forward or rearward to desired position Tighten bolts Do not operate the mower with bracket bolts in loose condition Mower Blade Operation To engage the mower blades turn lever floor slowly to the ON position To disengage mower blades turn lever slowly to the OFF position Removing The Body 1 Throttle cable from engine 2 Disconnect the wiring loom from the body by turning the threaded collar on the connector in a counterclockwise direction This connector is located at the left rear of the body 3 Remove four control lever bolts and remove upper control levers P N 9079 amp 9080 4 Remove the two attach nuts on the floor of the body and release the latches on the rear of the body near each side 5 Place height adjustment lever in the vertical position and mower deck engaging lever in the OFF position Carefully lift the body off the chassis 6 For assembly reverse the procedure Removing The Mower Deck 1 Loosen the belt keeper P N 2294 located under the engine by loosening two rear engine mounting bolts allowing the deck drive belt to come free of the rear pulley Tighten the belt keeper Disconnect the wiring loom at the deck safety sw
3. TION Over tightening may cause premature wear the brake band P N 5085 OIXON INDUSTRIES INC Box 494 Coffeyville Kansas 67337 0494 316 251 2000 P N 8603 CHASSIS ASSEMBLY MODEL 308 amp 311 3677 398 3678 311 3502 9080 w GRIP 9079 w SRIP 2401 ASSEMBLY 8578 WHEEL LT 2465 TIRE Ne e 2091 9102 ADVd CASTING 08 SUPPORT 5138 5139 CONTROL LEVER ADAPTER 2 5057 Prior 1084 2 8505 CUR TRANSAXLE ASSEMBLY MODEL 308 amp 811 jo 5 PAGE 4 of 6 2463 308 4014 311 lt 38 8670 308 BODY W DECALS 8671 311 BODY W DECAL 5 3699 311 BOBY ASSEMBLY MODEL ZTR 308 amp 311 MOWER DECK MODEL ZTR 308 amp 311 5 199 857 0 S 39 9 SEAT SWITCH TO DECK 4217 SWITCH BATTERY 4467 4465 ASSEMBLY 4466 COVER ONLY MAGNETO KI DAA 443 TO 4211 SOLENOID STARTER GABLE 4517 SHORT BODY WIRING LOOM 4484 REAR WIRING LOOM 4495 WIRING KIT 308 311 8669 SEE ASSEMBLY BREAKDOWN 9 9
4. itch P N 4242 Remove four attach pins P N 6107 and clips P H 3072 from the deck attach points and stabilizer bars 4 Lift the front of the mower chassis clear of the deck engaging rod P N 2686 Roll the chassis free of the deck 5 To install reverse the procedure Wh Adjustment Of Mower Deck Drive Belt 1 Disengage the mower deck drive belt 2 To obtain the proper belt tension loosen lock nut P N 3005 and rotate engaging rod linkage P N 3607 3 After making an adjustment engage the drive belt and check the tension The proper tension for an engaged V belt is the lowest tension at which the belt will not slip under normal load conditions 4 If further adjustment is necessary repeat steps 1 through 3 until proper adjustment is achieved 9 After the belt tension is adjusted check to assure that the mower blade will not turn freely when the engaging rod is in the OFF position 6 If the mower blade turns freely adjust the blade brake using swivel fitting P N 2172 located on the brake linkage L rod P N 2841 so that there is 1 8 to 1 4 g dam between the deck safety switch body P N 1242 and the striker plate attached to the clutch idler bracket P N 2847 when the brake is MR NOTE The clutch idler bracket P N 2847 must be raised so that the brake link swivel P N 2172 can be adjusted 7 After adjustment is achieved perform the safety checks listed below IMP
Download Pdf Manuals
Related Search