Dimplex ROD20 User's Manual
Contents
1. for the heater to operate Switch 2 Provides 1kw heat output Switch 3 Provides 2kw heat output with switch 2 Maintenance WARNING BEFORE UNDERTAKING ANY MAINTENANCE OR CLEANING REMOVE PLUG OR DISCONNECT FROM THE ELECTRICITY SUPPLY Lamp Replacement There is one lamp located beneath the fuel effect To gain access to the lamp remove the coal and place in a con tainer lift out the plastic fuel effect to reveal the lamp Replace the defective lamp with a 240V 60W fire glow 2 pin bayonet cap lamp Replace plastic fuel effect and coals Safety cut out For your safety this appliance has been fitted with thermal cut out In the event that the product overheats the cut out switches the heat off automatically To bring the heat back into operation remove the cause of the overheating then unplug or turn off the electrical supply to the heater for up to 10 minutes When the heater has cooled sufficiently re connect and switch on the heater Cleaning Before commencing cleaning unplug the heater and allow it to cool The surfaces of the heater should be given an occasional wipe over with a dry soft cloth Do not use detergents abrasive cleaning powder or polish on the metal body of the heater The glass screen should be cleaned carefully with a chamois leather DO NOT use proprietary cleaners To remove any accumulation of dust or fluff the soft brush attachment of a vacuum cleaner should occasionally be u2. a C Di m p ex Installation and Operating Instructions Dimplex Roda Fire Model ROD20 BEAB Approved 08 18797 1 Issue 1 Dimensions millimetres 115 55 13 128 514 617 4 Z A Roda Model ROD20 Fig 1 THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE Important Safety Advice When using electrical appliances Basic precautions should always be followed to reduce the risk of fire electrical shock and injury to persons including the following If the appliance is damaged check with the supplier before installation and operation Do not use outdoors Do not use in the immediate surroundings of a bath shower or swimming pool Do not locate the heater immediately below a fixed socket outlet or connection box Do not cover the heater Do not place material or garments on the heater or obstruct the air circulation around the heater for instance by curtains or furniture as this could cause overheating and a fire risk Do not leave young children or the infirm unsupervised in the vicinity of the heater Do not use this heater in series with a thermal control a program controller a timer or any other device that switches on the heat automatically since a fire risk exists when the heater is accidentally covered or displaced Ensure that furniture curtains or other combustible materi
3. al are positioned no closer than 1 metre from the heater In the event of a fault unplug the heater Unplug the heater when not required for long periods Although this heater complies with safety standards we do not recommend its use on deep pile carpets or on long hair type of rugs The appliance must be positioned so that the plug is accessible If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard General Unpack the heater carefully and retain the packaging for pos sible future use in the event of moving or returning the fire to your supplier Loose coals are packed separately within the carton When the heater is assembled the coals are placed on top of the fuel bed The coals may be removed and peb bles added in their place up to a maximum weight of 6kg The pebbles are supplied with the product The heater is designed for use inset into a 407mm 16 or 457mm 18 wide by 559mm 22 high fireplace opening see also section Installation in a fire place opening A 2kw fan heater discreetly positioned in the canopy of the fire provides heating in cold weather Switching allows half or full heat Before connecting the heater check that the supply voltage is the same as that stated on the heater Please note Used in an environment where background noise is very low it may be possible to hear the fan which operates
4. sed to clean the outlet grille of the fan heater located under the canopy To clean the fuel effect remove the coal pieces and wash in warm water The plastic tray should be wiped clean with a damp cloth When dry replace the coal pieces and arrange for best effect After Sales Service Your appliance is guaranteed for one year from the date of purchase We undertake to repair or exchange free of charge within this period any part with the exception of a lamp found to be defective due to a manufacturing fault Your rights under this guarantee are additional to your statu tory rights which in turn are not affected by this guarantee Please retain your receipt as proof of purchase C The product complies with the European Safety Standards EN60335 2 30 and the European Standard Electromagnetic Compatibility EMC EN55014 EN60555 2 and EN60555 3 which cover the essential requirements of EEC Directives 73 23 and 89 336 Glen Dimplex UK Limited Millbrook House Grange Drive Hedge End Southampton Hampshire S030 2DF Customer Services Republic of Ireland UK customer help line 8 00AM 6 00PM Mon Fri 8 30AM 1 00PM Sat Tel 0870 7270101 Fax 0870 7270102 e mail customer services glendimplex com Tel 01 8424833
5. the flame effect This is normal and should not be a cause for concern Electrical WARNING THIS APPLIANCE MUST BE EARTHED This heater must be used on an AC supply only and the voltage marked on the heater must correspond to the supply voltage Before switching on please read the safety warnings and operating instructions For your convenience the heater is fitted with a rewireable plug incorporating a 13 amp fuse In the event of replacing the fuse in the plug supplied a 13 amp fuse approved by ASTA to BS1362 must be used Installation in a Fireplace Opening At the rear of the fire two adjustable supports are provided for levelling the fire where the base of the fireplace opening is raised above the level of the hearth Adjust by removing the two screws holding each bracket in position then refit the bracket and the two screws in the re quired position The metal surround at the rear of the fire may be removed if full inset of this fire is required Operation The unique flame effect may be enjoyed whether or not the heating elements are in operation Controls The heater controls are located on the right hand side of the canopy heat outlet Three switches provide a choice of heat settings A switch is in the ON position when the red indicator mark on the switch is visible Fig 2 Switch 1 Controls the electricity supply to the heater and the flame effect Note This switch must be in the ON position
Download Pdf Manuals
Related Search