Dialogic Switch D41JCT-LS-W User's Manual
Contents
1. pS Part Function SW30 Rotary switch to set board ID number SW4 Switch to set hook switch state for start up J1 J4 RJ 11 jacks to connect to PBX or Central Office lines JP1 Jumper reserved JP2 Jumper to terminate CT Bus on board at each end of CT Bus cable factory default is unterminated CT Bus connector ECTF H 100 compliant CT Bus edge connector PCI bus connector PCI expansion bus edge connector 3 Insert the board s edge connector into the bus slot Use the slot s board guides as you insert the board edge connector into the slot Apply pressure only to the top edge of the board and press firmly until the edge connector is securely seated in the slot 4 Replace and tighten the retaining screw to secure the board If the screw is not installed and you attach a CT Bus cable to the board the board may be accidentally unseated from the slot 5 To install an additional board select an empty PCI slot adjacent to the location of the previous board and repeat the second part of step 2 through step 4 5 Attach CT Bus Cable to Board optional LLL Colored Stripe Pin 1 If you use the board in stand alone mode skip the instructions in this section Use a CT Bus cable to connect your board to other CT Bus form factor boards in the system A Caution To preserve the electrical integrity of the CT Bus use a CT Bus cable with the appropriate number of connectors drops We recommend tha2. CT Bus with a CT Bus cable You can connect the board to the CT Bus or use it without the CT Bus in stand alone mode Stand Alone Mode CT Bus Jumpers Ignored For applications that do not require media sharing or switching across the CT Bus use the board in stand alone mode No CT Bus cable is required You can skip the rest of this section and proceed to Section 4 Install the Board In addition you may skip the instructions in this section when you use the board in SCbus mode without a CT Bus master board that is using only SCbus master slave boards CT Bus Mode CT Bus Jumpers Needed To connect the boards to the CT Bus set the CT Bus jumpers according to instructions in this section Note If these boards are operating in SCbus mode CT Bus H 100 termination is not required The following instructions only apply to the boards at each end of the CT Bus cable Only boards at each end of the CT Bus cable must be terminated JP1 jumper is reserved and unused DO NOT install a shunt across the pins of JP1 JP2 is a 2 pin jumper that is used to terminate the CT Bus ensuring that proper electrical characteristics exist on the CT Bus By factory default this jumper is not terminated on the board To use the CT Bus e Install the shunt on the JP2 jumper of a board to terminate the CT Bus at that board e Only terminate the first and last boards the boards located at each end on the CT Bus cable e Do
3. as desired A Set the Board ID Number When you start Dialogic boards each board is assigned a sequential number for identification and use by the system software This sequential number specifies the device and channel name s for each board The board number is based on the board ID that you set using the SW30 rotary switch on the board Use the SW30 rotary switch to specify board sequencing as follows e Automatic Assignment Board ID 0 Also called geographical method All Dialogic PCI boards can share the factory default setting of board ID 0 In this case boards are automatically sorted by PCI bus and slot number Note Adding or removing a board can cause the renumbering of boards in the system Consequently the assignment of device names may change during the next system start up e Manual Assignment Board IDs 1 9 A F In addition to the automatic assignment method you can use the manual or discrete assignment method to further identify boards in your system If you change the board ID from the factory default of 0 to any other number the software will use that setting to identify the board Note When not set to 0 the board ID must be unique It must not conflict with the board ID of any other Dialogic ISA or PCI board If you use this method we recommend that you assign sequential numbers starting at 1 This method is also used for all ISA bus boards Numbering Precedence in Mixed Systems In systems using bo
4. Connect the Earth Recall signal to pin 2 DO NOT connect Tip or Ring lines to pin 2 or improper operation of the D 41JCT LS will result 9 Install Software Configure and Test Install the Dialogic software release and configure the Dialogic boards as described in the Dialogic Installation and Configuration Guide for your operating system Your application software or Dialogic software release may have special installation or configuration requirements Be sure to read your software documentation including release note information before you install the software Note If you are adding hardware to an existing system you do not need to uninstall existing Dialogic software Warranty and Return Information For technical specifications and product information visit the Dialogic website http vww dialogic com or use the Dialogic On Line Information Retrieval System at 1 800 755 5599 or 1 973 993 1063 Warranty Period This Dialogic board has a 3 year warranty See the Hardware Limited Warranty on the back of the Regulatory Notice for coverage details Repair of Merchandise Authorization RMA Process 1 Before completing the RMA process verify that the problem is not due to a mistake or oversight in the installation process Choose one of the following methods e On the Web go to the Dialogic FirstCall Info Server at http support dialogic com and browse through the various topics e If you have a Dialogic Su
5. Dialogic an Intel company D 41JCT LS E Installation m Warranty Period E RMA Procedure Part Number 05 1352 001 Copyright 2000 Dialogic Corporation All Rights Reserved 1 Protect Boards from Damage b 4A Caution Computer boards are static sensitive and can be damaged by touching or handling To prevent damage from static electricity do the following e Wear a grounded static dissipating wrist strap for the entire hardware installation e Work at a static safeguarded work station see below Grounded Static Dissipative Wrist Strap L y Ground ae J AAJ R A a Grounded Common y Static Dissipative Ground M t y Point The work surface drains electrical charges from conductive materials when the materials are placed on the surface The grounded static dissipating wrist strap drains static charge from the person wearing the strap Both components ensure that static charges are drained at a rate and current level that are safe Both must be used any time a person is handling a board or component 2 Set Hardware Switches The D 41JCT LS board includes hardware auto configuration for IRQ and memory address This technology lets you use the factory default hardware settings for quick installation and operation However we recommend that you review the following information before installing your board and select any options
6. alled must be inserted in the first PCI slot adjacent to an ISA slot Locate this board 2 Align pin 1 of the adapter with pin 1 of the edge connector on the board Press the adapter onto the board with the SCbus cable connector facing the rear edge of the board CT Bus SCbus Adapter CT Bus Cable lt SCbus Colored Stripe N Pin 1 Indicator D xxx JCT A ISA lots PCI Slots For more information see the hardware installation instructions for the CT Bus SCbus Adapter 7 Complete Board Installation After you have installed the board s and if applicable attached cables and adapter replace the computer cover and re attach power cords 8 Connect External Cables e Each RJ 11 jack on the rear bracket of the voice board supports a single voice channel Use each RJ 11 jack and phone cable to connect each channel to an analog PBX or standard telephone outlet e Since this board emulates a standard telephone a standard telephone will not function when directly attached to the board Rear E amp bracket on board Channel 1 ae To analo Channel 2 r PBX g or standard Channel 3 i 1 4 telephone outlet Channel 4 ae J1 J4 on the Pin Signal D 41JCT LS Board 1 Unused RJ 11 Connector 2 Station Earth Recall 123456 3 Station Ring mM 4 Station Tip 5 Unused 6 Unused Note
7. correct static safe handling procedures Disconnect power cables and remove the board from the chassis 3 Record the serial number two letters followed by numeric digits and located on a label on the board 4 Include your Service Request Number given to you by a Technical Support representative if appropriate 5 E mail the RMA form to the RMA Department After you receive an RMA number from Dialogic return the problem board to Dialogic as outlined in the steps below a Pack the board s in their original anti static packaging and protected packaging Clearly display the RMA number on the package If this number is not on your package it will be treated as an unauthorized return Note Dialogic is not responsible for risk of loss or damage in transit Ship the board to the Dialogic address listed below Dialogic 1515 Route 10 Parsippany NJ 07054 USA ATTN RMA
8. not install a shunt across the pins of JP2 on boards located between the end boards on the CT Bus cable the shunt must be disconnected on the JP2 jumper to disable termination The JP2 jumper terminates the H 100 signals listed in the following table JP2 Pins 1 and 2 CT_FRAME A amp B CT_C8_ A amp B used on boards at each end of CT Bus cable only 4 Install the Board A Warning To reduce the risk of electric shock e Switch off the power and disconnect all power cords e Do not re attach power cords or switch on power to the computer while the computer cover is removed Install the board in the computer chassis according to the following instructions 1 Remove the computer cover 2 Select an empty PCI bus slot and remove the slot s retaining screw and access coverplate 3 Retaining Screw gt Vf Metal Coverplate for Slot gt t 5 h o o 46 Bit ISA Slots 32 Bit PCI Slots Note If you are not installing your board in an ISA form factor PCI slot remove the slot retainer bracket from the end of the board before installation Physical Description SW30 SW4 CT Bus connector Lemar ce Pin 1 JP2 J1 Sy J2 JP1 Y J3 J4 F umpono Qu y PGI Dus conngator slot retainer bracket 7 rear bracket JP2 top row pins 1 and 2 JP1 bottom row pins 1 and 2
9. pport Plan contact one of our Technical Support Departments listed below and they will troubleshoot the problem over the phone The Americas 973 993 1443 Continental Europe Middle East Africa 32 2 712 4321 Southeast Asia West Asia and Australia New Zealand 65 339 9833 For more information and a complete list of Worldwide Technical Support centers visit http www dialogic com support tech htm 2 After you have determined that you have a problem board do one of the following e For Dialogic products purchased outside of the United States or Canada contact your local Dialogic Sales Office for RMA procedures For Dialogic products purchased from a distributor the distributor owns the warranty and you MUST go through them if you do not want to be charged for the repair Note You may return the board to Dialogic for repair even if you did not purchase your board through the Dialogic Corporate Sales Office However if the repairs are not authorized by your local distributor or local Dialogic Sales office the board is considered out of warranty and a fee is charged for repair services Go to the Dialogic Technical Support website at http support dialogic com rma and fill out the Repair of Merchandise Authorization form 1 To complete the RMA form you will need the serial number of the board This information must be given at the time of the return or the request cannot be processed 2 Observe
10. t no more than two connectors at either end of the cable be left unused In addition it is preferable to distribute the installed boards in slots along the length of the CT Bus cable rather than clustered in one area Attach the CT Bus cable to the Dialogic board as follows 1 Attach the end connector on the CT Bus cable to the CT Bus edge connector on the top edge of the first board in the sequence The connectors are designed to fit together one way only If the connector does not seat fully on the board turn the cable around and try again Make sure that the colored stripe on the cable faces the rear bracket 2 Attach the cable to the next board until all boards are connected by the cable Colored Stripe Pin 1 Your CT Bus cable may have a different number of connectors drops 3 If the cable has extra connectors or is loose tuck the cable down so that it does not snag when you replace the computer cover See the Caution given earlier in this section 6 Connect CT Bus SCbus Adapter optional If you use the board in stand alone mode skip the instructions in this section To connect your board to SCbus form factor boards use the CT Bus SCbus adapter part number 99 2446 001 You may use only one CT Bus SCbus adapter per system 1 Before installing the adapter the Dialogic boards in your chassis must be positioned in the correct order The board on which the adapter is inst
11. th automatic and manual assignment methods or where both ISA and PCI boards exist PCI boards take precedence and are numbered before an ISA board that uses board IDs 1 9 or A F Note The Dialogic software can correctly register your boards for proper operation however due to variations among computer chassis it is not possible for the software to determine where each board is physically placed For more information on board ID numbering issues see the Dialogic Installation and Configuration Guide for your operating system or visit the Dialogic Technical Support website at http support dialogic com tnotes tnbyos winnt tn187 htm B Set the Hook Switch State for Start Up Optional Set the SW4 switch as follows to select how the board responds to an incoming call when the computer power is on but the board is not initialized Ringing On Hook Sy i SW4 Off default Callers hear ringing on hook Busy Off Hook SW4 i ON 3 SW4 On Callers hear a busy signal off hook Note If the computer power is off callers hear ringing on hook regardless of the setting of the SW4 switch 3 Set CT Bus Jumpers optional The Computer Telephony bus CT Bus provides communication and flexible resource sharing among the boards connected to the bus This Dialogic board has a CT Bus connector that complies with the ECTF H 100 specification and as such can be connected to the
Download Pdf Manuals
Related Search