De'Longhi Coffeemaker ETAM36.365 User's Manual
Contents
1. 17 SETTING WATER HARDNESS Measuring water hardness Setting water hardness WATER SOFTENER FILTER Installing the filter Removing the filter E Electrical connection UK only 222 19 DISPLAYED MESSAGES 20 5 00 21 TECHNICAL DATA Voltage 220 240 V 50 60 Hz max 10 Absorbed power 1450W Pressure 15 bar Max water tank capacity 131 Size LxHxD 195x325x500 mm Cable length 180m Weight 10 8 kg Coffee beans container capacity 150g C The appliance complies with the following EC directives Low Voltage Directive 2006 95 EC and subsequent amendments EMC Directive 2004 108 EC and subsequent amend ments European Stand by regulation 1275 2008 Materials and accessories coming into contact with food conform to European regulation 1935 2004 DISPOSAL In compliance with European directive 2002 96 EC the ap pliance must not be disposed of with household waste but taken to an authorised waste separation and recycling cen tre INTRODUCTION Thank you for choosing the ETAM36 365 automatic bean to cup espresso and cappuccino machine We hope you enjoy using your new appliance Take a few minutes to read these instructions This will avoid all risks and damage to the appliance Symbols used in these instructions Important warning2. The milk contains large bubbles and squirts out of the milk spout or there is little froth The milk is not cold enough or is not semi skim med Use skimmed or semi skimmed milk at refrigerator tem perature about 5 C If the result is not as you wished try changing brand of milk The froth adjustment dial is incorrectly adjusted Adjust following the instructions in the section Making cappuccino and milk based coffees The milk container lid or froth adjustment dial are dirty Clean the milk container lid and dial as described in the sec tion Cleaning the milk container The hot water steam nozzle is dirty Clean the nozzle as described in the section Cleaning the hot water steam nozzle The milk contains large bubbles and squirts out of the milk spout or there is little froth The spout is dirty Clean as described in the section Cleaning the spout after 2 use The appliance does not come on The connector is not inserted correctly Insert the connector as far as it will go in the socket at the back of the appliance It is not plugged into the mains socket Plug into the mains socket The main switch A20 is not turned on Press the main switch fig 2 The infuser cannot be extracted The appliance has not been turned off correctly Turn the appliance off by pressing the ON STANDBY button page 9 21
3. De Longhi Appliances 47 31100 Treviso Italia 6_ 2 13 BEAN TO CUP ESPRESSO AND CAPPUCCINO MACHINE Instruction for use UU ETAM36 365 ee Co Le E ona CONTENTS TECHNICAL DATA DISPOSAL INTRODUCTION Symbols used in these instructions Letters in brackets Troubleshooting and repairs SAFETY Fundamental safety warnings DESIGNATED 05 7 INSTRUCTION FOR 05 70 2 4 4 0 2 7 DESCRIPTION Description of appliance Description of control panel Description of milk container Description of accessories BEFORE USE 8 Checking the appliance Installing the appliance Connecting the appliance Setting uptheappli nge seinem TURNING THE APPLIANCE ON eere 9 TURNING THE APPLIANCE 404 4 9 MENU SETTINGS 10 Rinsing Descaling Install filter Replacing the filter if installed Adjust time Auto start Auto off Auto standby timer auto off time
4. Energy saving Setting the temperatur Setting water hardness Setting the language Cup lighting Default values rese Statistics function MAKING COFFEE Selecting the coffee taste Selecting the quantity of coffee in the Coffee selec Quantity in cup ml Customising the my coffee quantity Adjusting the coffee mill Tips for a hotter coffee Making coffee using coffee beans Making coffee using pre ground coffe MAKING MILK BASED DRINKS eene illing and attaching the milk container Adjusting the amount of froth Making milk based drinks automatically Clean the milk frother by using the CLEAN button 14 rogramming the quantity of coffee and milk in the cup for the FLAT WHITE CAPPUCCINO LATTE and MILK 14 DELIVERING HOT WATER AND STEAM 14 Delivering hot water Changing the quantity of water delivered automatically Steam delivery Tips for using steam to froth milk Cleaning the spout after use Cleaning the coffee grounds container Cleaning the drip tray and condensate tray Cleaning the inside of the coffee machine Cleaning the water tank Cleaning the coffee spouts Cleaning the pre ground coffee funnel Cleaning the infuser Cleaning the milk container Cleaning the hot water steam nozzle 5
5. The infuser has cooled down because 2 3 minutes have elapsed since the last coffee was made Before making the coffee heat the infuser by rinsing using he rinse function page 10 A low coffee temperature is set Set a higher coffee temperature in the menu The coffee is weak or not creamy enough The coffee is ground too coarsely Turn the grinding adjustment dial one click anticlockwise owards 1 while the coffee mill is in operation fig 13 Continue one click at a time until coffee delivery is satisfac ory The effect is only visible after delivering 2 coffees see he section Adjusting the coffee mill on page 13 The coffee is unsuitable Use pre ground coffee for espresso machines only The coffee is delivered too slowly or a drop at a time The coffee is ground too finely Turn the grinding adjustment dial one dick clockwise to wards 7 while the coffee mill is in operation fig 13 Continue one click at a time until coffee delivery is satisfac ory The effect is only visible after delivering 2 coffees see the section Adjusting the coffee mill on page 12 Coffee does not come out of one or both of the spouts The spouts are blocked Clean the spouts with a toothpick fig 33B The milk does not come out of the milk spout The milk container lid is dirty Clean the milk container lid as described in the section Cle aning the milk container
6. the machine FILL TANK EMPTY GROUNDS CONTAINER etc Their meaning is explained in the section Displayed messages page 21 For hotter coffee see the section Tips for a hotter coffee page 13 If the coffee is delivered a drop at a time too weak and not creamy enough or too cold read the tips in the Trouble shooting section on page 22 Making coffee using pre ground coffee A Important Never add pre ground coffee when the machine is off or it could spread through the inside of the machine and dirty it This could damage the appliance Never use more than one level measure as it could dirty the inside of the machine or block the funnel i Please note If you use pre ground coffee you can only make one cup of coffee at a time 1 Press the aroma selection button 06 fig 10 until Pre ground is displayed 2 Openthe beans container lid then open and raise the pre ground coffee funnel lid 3 Make sure the funnel is not blocked then add one level measure of pre ground coffee fig 18 4 Placea cup under the coffee spouts 5 Press the 1 cup button fig 15 6 Preparation begins The amount of coffee selected is dis played together with a progress bar which gradually fills as preparation progresses i Please note If Energy saving mode is active you may have to wait a few seconds before the first coffee is delivered MAKING MILK BASED DRINKS 0 Please note To avo
7. 250 ml of hot water then delivery stops automatically To interrupt delivery of hot water manually press button again Changing the quantity of water delivered automatically The machine is set by default to automatically deliver 250 ml of hot water To modify these quantities proceed as follows 1 Position a container under the spout 2 Press and hold the button until Program quan tity HOT WATER is displayed then release 3 When the hot water in the cup reaches the required level press the 0 OK button again The machine is now reprogrammed with the new quantity Steam delivery 1 Make sure the hot water spout is attached correctly fig 7 2 Fill a container with the liquid to be heated frothed and immerse the spout cappuccino maker D5 in the liquid 3 Press the steam dh button After a few seconds the steam to heat the liquid comes out of the cappuccino maker and STEAM is displayed 4 When the required temperature is obtained interrupt steam delivery by pressing the steam db button again You should not discharge steam for more than 3 minutes at a time N Important Always stop steam delivery before extracting the container containing the liquid to avoid burns from splashes Tips for using steam to froth milk When choosing the size ofthe container bear in mind that the liquid doubles or triples in volume For a richer denser froth use skimmed or partially s
8. For instructions on how to replace the filter see the section Replacing the filter page 20 Adjust time To adjust the time on the display proceed as follows 1 Pressthe MENU ESC button to enter the menu 2 Press the scrolling arrow lt or gt fig 9 until Adjust time is displayed 3 Pressthe amp OK button fig 3 The hours flash on the display 4 Press the scrolling arrow lt or gt fig 8 to change the hour 5 Press the amp OK button to confirm The minutes flash 6 Press the scrolling arrow or gt fig 9 to change the minutes 7 Pressthe amp OK button to confirm The time is set press the MENU ESC button to exit the menu Auto start You can set the auto start time in order to have the appliance ready at a certain time for example in the morning so you can make coffee immediately i Please note To enable this function the time must already be set correctly To enable Auto start proceed as follows 1 Pressthe MENU ESC button to enter the menu 2 Pressthescrolling arrow lt or gt fig 9 until Auto start is displayed 3 Press the 0 ok button Enable is displayed 4 Press the 0 0 button to confirm 5 Press the scrolling arrow lt or gt to choose the hour 6 Press the 0 button to confirm 7 Press the scrolling arrow lt or gt fig 9 to change the minutes 8 Press the 0 0 button to confirm 9 Press the MENU ESC
9. Important Danger of burns Hot water containing acid flows out of the hot water spout Avoid contact with splashes of water 9 Pressthe 0 OK button to confirm that you have added the solution The descale programme automatically per forms a series of rinses and pauses to remove limescale deposits from inside the machine DESCALE Please wait is displayed The descale pro gramme starts and the descaler liquid comes out of the water spout After about 30 minutes the message RINSING INSERT FILTER if previously removed FILL TANK is displayed 10 The appliance is now ready for rinsing through with clean water Remove the water tank empty rinse under running water reinsert the water filter if previously re moved fill with clean water and replace RINSING Press OK is displayed 11 Empty the container used to collect the descaler solution and replace it empty under the hot water spout 12 Pressthe ok button to start rinsing Hot water flows out of the spout and the message RINSING Please wait is displayed 13 When the water tank is completely empty the message Rinsing complete Press OK is displayed 14 Pressthe 0 button 15 Heating up please wait is displayed when completed the appliance is ready for use SETTING WATER HARDNESS The DESCALE message is displayed after a period of time es tablished according to water hardness The machine is set by defaul
10. button corresponding to the drink you want to make If the milk container is attached to the appliance the en ergy saving function is not active Setting the temperature To modify the temperature of the water used to make the cof fee proceed as follows 1 Pressthe MENU ESC button to enter the menu 2 Pressthe scrolling arrow lt or gt fig 9 until Set tem perature is displayed 3 Pressthe 0 button 4 Press the scrolling arrow lt or gt until the required tem perature is displayed 69 O 6 maximum 5 Pressthe button to confirm 6 Press the MENU ESC button to exit the menu Setting water hardness For instructions on setting water hardness see page 19 Setting the language To modify the language of the display proceed as follows 1 Pressthe MENU ESC button to enter the menu 2 Press the scrolling arrow lt or gt fig 9 until Set lan guage is displayed 3 Pressthe 0 0 button 4 Press the the scrolling arrow or gt until the required language is displayed 5 Pressthe 0 ok button to confirm 6 The set language is displayed 7 Press the MENU ESC button to exit the menu Beep This enables or disables the beep emitted by the machine each time the buttons are pressed or an accessory is inserted re moved To disable or re enable the beep proceed as follows 1 Press the MENU ESC button to enter the menu 2 Press the scrolling arr
11. coffee For hotter coffee you should perform a rinse cycle by selecting the Rinsing function in the settings menu page 10 warm the cups by rinsing them with hot water using the hot water function increase the coffee temperature in the settings menu page 11 Press the 0 button to enable the cup warmer the symbol is displayed Making coffee using coffee beans A Important Do not use caramelised or candied coffee beans as they could stick to the coffee mill and make it unusable 1 Fill the container with coffee beans fig 14 2 Place under the coffee spouts 1 cup if you want 1 coffee fig 15 2 cups if you want 2 coffees fig 17 3 Lower the spout as near as possible to the cups fig 16 This makes a creamier coffee 4 Pressthe button corresponding to the number of coffees required 1 cup or2 cups CPC 5 Preparation begins The amount of coffee selected is dis played together with a progress bar which gradually fills as preparation progresses o Please note While the machine is making coffee delivery can be in terrupted at any moment by pressing one of the delivery buttons At the end of delivery to increase the quantity of coffee in the cup just press and hold within 3 seconds one of the coffee buttons Y or CPC Once the coffee has been made the appliance is ready to be used again o Please note Various alarm messages could be displayed while using
12. of the components of the appliance can be washed in a dishwasher with the exception of the milk container 0 Do not use metal objects to remove encrustations or coffee deposits as they could scratch metal or plastic surfaces Cleaning the coffee grounds container When EMPTY GROUNDS CONTAINER is displayed the grounds container must be emptied and cleaned The appliance cannot be used to make coffee until you have cleaned the grounds container Even if not full the empty grounds container message is dis played 72 hours after the first coffee has been prepared For the 72 hours to be calculated correctly the machine must never be turned off with the main switch in the 0 position N important Danger of burns If you make a number of cappuccinos one after the other the metal cup tray becomes hot Wait for it to cool down before touching it and handle it from the front only To clean with the machine on Remove the drip tray fig 28 empty and dean Empty the grounds container and clean thoroughly to remove all residues left on the bottom This can be done with the spatula on the brush provided Check the condensate tray and empty if necessary fig 29 A Important When removing the drip tray the grounds container must be emptied even if it contains few grounds If this is not done when you make the next coffees the grounds container may fill up more than expected and clog the machine Cleaning th
13. the coffee spouts and milk spout 2 Press and hold one of the function buttons until the mes sage Program quantity PROGRAM MILK is displayed 3 Release the button The appliance starts delivering milk 4 Oncetherequired quantity of milk has been delivered into the cup press the button again 5 The appliance stops delivering milk and if required for the drink being prepared after a few seconds the coffee is delivered into the cup Program quantity PROGRAM COFFEE is displayed 6 Once the required quantity of coffee has been delivered into the cup press the button again Coffee delivery stops The machine is now reprogrammed with the new milk and cof fee quantities DELIVERING HOT WATER AND STEAM A Important Danger of burns Do not leave the appliance unattended while hot water or steam is being delivered The spout becomes hot during deliv ery Hold by the handle only i Please note If Energy saving is active you may have to wait a few seconds before hot water and steam are delivered Delivering hot water 1 Make sure the hot water spout is attached correctly fig 7 2 Place a container under the spout as close as possible to avoid splashes 3 Press the amp OK button fig 3 Preparation underway is displayed if required Then hot water is delivered and HOT WATER is displayed together with a progress bar which fills gradually as preparation proceeds 4 The machine delivers about
14. the socket used is freely accessible at all times enabling the appliance to be unplugged when necessary Unplug directly from the plug only Never pull the power cable as you could damage it To disconnect the appliance completely release the main switch at the side of the appliance by pushing fig 2 If the appliance is faulty do not attempt to repair Turn it off unplug from the mains socket and contact Customer Services Ifthe plug or power cable is damaged it must be replaced by De Longhi customer services only to avoid all risk A Important Keep all packaging plastic bags polystyrene foam away from children The appliance is not intended for use by persons includ ing children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concern ing use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance A Danger Risk of burns This appliance produces hot water and steam may form while it is in operation Avoid contact with splashes of water or hot steam DESIGNATED USE This appliance is designed and made to prepare coffee and heat drinks All other use is considered improper This appliance is not suitable for commercial use The manufacturer is not liable for damage deriving from im proper use of the appliance This
15. the tank and exhausted filter 2 Press the MENU ESC button to enter the menu 3 Press the scrolling arrow lt or gt fig 9 until Install fil ter Installed is displayed 4 Press the 0 button 5 message Uninstall appears on the display 6 Press the button to confirm and the MENU ESC button to exit the menu Electrical connection UK only A Ifyourappliance comes fitted with a plug it will incorporate a 13 Amp fuse If it does not fit your socket the plug should be cut off from the mains lead and an appropriate plug fitted as below WARNING Very carefully dispose of the cut off plug after removing the fuse do not insert in a 13 Amp socket elsewhere in the house as this could cause a shock hazard With alternative plugs not incorporating a fuse the circuit must be protected by a 15 Amp fuse If the plug is a moulded on type the fuse cover must be re fitted when changing the fuse using a 13 Amp Asta approved fuse to BS 1362 In the event of losing the fuse cover the plug must NOT be used until a replacement fuse cover can be obtained from your nearest electrical dealer The colour of the correct replacement fuse cover is that as marked on the base of the plug B If your appliance is not fitted with a plug please follow the instructions provided below WARNING THIS APPLIANCE MUST BE EARTHED IMPORTANT GREEN AND YELLOW EARTH C BLUE NEUTRAL O BROWN LIVE As the colours of
16. the wires in the mains lead may not correspond with the col oured markings identifying the terminals in your plug proceed as follows The green and yellow wire must be connected to the terminal in the plug marked with the letter E or the earth symbol or coloured green green and yel low The blue wire must be connected to the terminal marked with the letter N or coloured black The brown wire must be connected to the terminal marked with the letter L or coloured red DISPLAYED MESSAGES DISPLAYED MESSAGE POSSIBLE CAUSE SOLUTION FILL TANK Insufficient water in the tank Fill the tank with water and or insert it correctly pushing it as far as it will go until it clicks into place EMPTY GROUNDS CONTAINER The grounds container A18 is full Empty the grounds container and drip tray clean and replace fig 29 Important when removing the drip tray the grounds contai ner MUST be emptied even if it contains few grounds If this is not done when you make the next coffees the grounds container may fill up more than expected and clog the machine GROUND TOO FINE ADJUST MILL The grinding 15 too fine and the coffee is delivered too slowly or not at all Repeat coffee delivery and turn the grinding adjustment dial fig 13 one click clockwise towards 7 while the coffee mill is in operation If after making at least 2 coffees delivery is still too slow repeat the correction procedure turn
17. thoroughly as described in the section Cleaning If the message is still displayed after cleaning contact customer services WATER CIRCUIT EMPTY FILL The water circuit is empty Press OK to deliver water from the spout A11 until it flows WATER CIRCUIT out normally Water delivery PRESS OK REPLACE FILTER The water softener filter is exhausted Replace the filter or remove it as described in the section Water softener filter TURN DIAL TO CLEAN Milk has been delivered recently and the tubes inside the Turn the froth adjustment dial to CLEAN milk container must be cleaned INSERT WATER SPOUT The water spout is not inserted or is inserted incorrectly Insert the water spout D5 as far as it will go INSERT MILK CONTAINER The milk container is not inserted correctly Insert the milk container fig 23 as far as it will go DESCALE Descaling is necessary See par DESCALING REPLACE FILTER Replace water filter See par Replace water filter 20 TROUBLESHOOTING Below is a list of some of the possible malfunctions If the problem cannot be resolved as described contact customer services PROBLEM The coffee is not hot POSSIBLE CAUSE The cups were not preheated SOLUTION Enable the cup warmer leave the cups at least 20 minutes to warm up Warm the cups by rinsing them with hot water PLEASE NOTE you can use the hot water function
18. age2 B A number of buttons on the panel have a double function This is indicated in brackets in the description B1 06 aroma selection button press to select coffee taste B2 GA gt wg button to select coffee quantity B3 MENU button to access the menu When in the settings menu press to exit the menu B4 Display guides the user in using the appliance B5 0 OK button to deliver hot water When in the settings menu press to confirm the selection B6 button to make 1 cup of coffee with the settings displayed B7 CPC button to make 2 cups of coffee with the set tings displayed B8 dh button to deliver steam When in the settings menu press to scroll through the menu items B9 MILK button to deliver a cup of milk B10 LATTE button to deliver a latte B11 CAPPUCCINO button to deliver a cappuccino B12 FLAT WHITE button to deliver a flat white When in the settings menu press to scroll through the menu items Description of milk container page2 C C1 Milk container lid C2 Froth adjustment and CLEAN dial Milk container C4 Lid extraction button C5 Frothed milk spout adjustable C6 Milk intake tube Description of accessories page2 D D1 Pre ground coffee measure D2 Cleaning brush D3 Water softener filter certain models only D4 Cappuccino maker hot water spout release button D5 Cappuccino maker hot water spout D6 Power cable D7 Total Hardness Test indicator pa
19. amme Auto off proceed as follows 1 Press the MENU ESC button to enter the menu 2 Press the scrolling arrow lt or gt fig 9 until Auto standby timer or Auto off is displayed 3 Pressthe 0 OK button 4 Press the scrolling arrow lt or gt fig 9 until the number of minutes hours of operation is displayed 15 or 30 min utes or 1 2 or 3 hours 5 Pressthe ok button to confirm 6 Press the MENU ESC button to exit the menu Auto off is programmed Energy saving Use this function to enable or disable energy saving When enabled the function reduces energy consumption in compliance with European regulations To disable or enable energy saving proceed as follows 1 Press the MENU ESC button to enter the menu 2 Press the scrolling arrow lt or gt fig 9 until Energy saving is displayed 3 Press the OK button Disable is displayed or En able if the function has already been disabled 4 Press the amp button to disable or enable energy saving mode 5 Press the MENU ESC button to exit the menu When the function is active Energy saving is displayedafter a period of inactivity i Please note Whenin energy saving mode a few seconds elapse before the first coffee cappuccino or milk based coffee is deliv ered as the appliance must heat up again To prepare a drink press any button to exit energy sav ing then press the
20. ative symbol flash on the display N important Descaler contains acids which may irritate the skin and eyes It is vital to follow the manufacturer s safety warn ings given on the descaler pack and the warnings relating to the procedure to follow in the event of contact with the skin and eyes Use De Longhi descaler only Under no circumstances should you use sulphamic or acetic based descalers Their use invalidates the guarantee Failure to descale the appli ance as described above also invalidates the guarantee 1 Turn the machine on 2 Press the MENU 36 ESC button to enter the menu 3 Press lt or gt until Descale is dis played 4 Select by press ing the oK button Confirm is displayed Press the ds oK but ton to confirm 5 DESCALE EMPTY DRIP TRAY is displayed alternating with Remove filter if the filter is present and ADD DES CALER PRESS OK 6 Empty the water tank A9 completely and remove the water softener filter if present Empty the drip tray fig 29 and grounds container then put them back in the ap pliance 7 Pour the descaler into the tank up to level A correspond ing to a 100 ml pack marked on the back of the tank fig 36 then add water 1 litre up to level B fig 36 and put the water tank back 8 Place an empty container with a minimum capacity of 1 5 litres under the hot water spout fig 7 A
21. button to exit the menu Once the time has been confirmed activation of auto start is indicated by the small bell displayed alongside the time To disable the function 1 Select auto start from the menu 2 Pressthe OK button Disable is displayed 3 Pressthe 0 oK button to confirm The small bell de is no longer displayed Auto off When this function is enabled the appliance is automatically turned off completely re leasing the main switch To turn the appliance on again press the main switch A20 and then the ON stand by button A23 When this function is disabled the appliance switches to stand by power remains on and it consumes a minimal amount of electricity To turn the appliance on again press the ON stand by button A23 The stand by time can be modified using Auto off timer if Auto off is enabled or Auto standby timer if Auto off is disabled To enable or disable auto off proceed as follows 1 Press the MENU ESC button to enter the menu 2 Press the scrolling arrow lt or gt fig 9 until Auto standby timer or Auto off is displayed 3 Press the 0 ok button Enable or Disable is dis played 4 Press the amp OK button to confirm 5 the MENU ESC button to exit the menu Auto standby timer auto off timer Auto off can be set so that the appliance goes off after 15 or 30 minutes or 1 2 or 3 hours To re progr
22. e drip tray and condensate tray A Important The drip tray is fitted with a level indicator red showing the level of water it contains fig 30 Before the indicator protrudes from the cup tray the drip tray must be emptied and cleaned otherwise the water may over flow the edge and damage the appliance the surface it rests on or the surrounding area To remove the drip tray 1 Remove the drip tray and grounds container fig 28 2 Empty the drip tray and grounds container and wash them 3 Check the condensate tray and empty if necessary 4 Replace the drip tray complete with grounds container Cleaning the inside of the coffee machine A Danger of electric shock Before cleaning internal parts the machine must be turned off see Turning off and unplugged from the mains power supply Never immerse the coffee machine in water 1 Check regularly about once a week that the inside of the appliance accessible after removing the drip tray is not dirty If necessary remove coffee deposits with the brush supplied and a sponge 2 Remove the residues with a vacuum cleaner fig 31 Cleaning the water tank 1 Clean the water tank A7 regularly about once a month and whenever you replace the water softener filter if pro vided with a damp cloth and a little mild washing up liq uid 2 Remove the filter if present and rinse with running wa ter 3 Replace the filter if provided fill the tank wit
23. e selection The appliance begins hot water delivery and the message Please wait is displayed 15 After delivery the appliance is automatically ready to make the next drink The filter is now active and you can use the coffee machine Replacing the filter When the symbol Fl is displayed together with the mes sage REPLACE FILTER after two months see date indicator or when the appliance has not been used for 3 weeks you should replace the filter 1 Extract the tank and exhausted filter 2 Remove the new filter from the packaging and proceed following steps from 2 to 6 of the paragraph before 3 Position a container with a minimum capacity of 100 ml under the hot water spout Press the MENU ESC button to enter the menu Press lt or gt until Replace filter is displayed Pressthe 0 button Confirm is displayed Press the amp OK button to confirm the selection SoS gm 9 Water delivery Press OK is displayed 10 Press the amp OK button to confirm the selection The appliance begins hot water delivery and the message Please wait is displayed 11 After delivery the appliance is automatically ready to make the next drink The new filter is now active and you can use the coffee ma chine Removing the filter If you want to use the appliance without the filter you must remove it and notify the appliance of its removal Proceed as follows 1 Extract
24. f burns During rinsing a little hot water flows from the coffee spouts Avoid contact with splashes of water To turn the appliance off press the ON STANDBY d but ton fig 8 The appliance performs a rinse cycle then goes off stand by i Please note If you will not be using the appliance for some time unplug from the mains socket 2 turn the appliance off by pressing the ON STANDBY d button fig 8 release the main switch at the side of the appliance fig A Important Never press the main switch while the appliance is on MENU SETTINGS To access the settings menu press the button corresponding to MENU Scroll through the menu by pressing the scrolling arrow or gt fig 9 Rinsing Use this function to deliver hot water from the spout to heat the internal circuit and make the coffee delivered hotter To enable the function proceed as follows 1 Press the MENU ESC button to enter the menu 2 Press the scrolling arrow lt or gt fig 9 until Rinsing is displayed 3 Press the amp button Confirm is displayed 4 Press the ds button fig 3 Hot water flows out of the spout heating the internal circuit and making the cof fee delivered hotter Descaling For instructions on descaling see page 18 Install filter For instructions on how to install the filter see the section Wa ter softener filter page 19 Replacing the filter if installed
25. f froth Turn the froth adjustment dial to adjust the amount of froth on the milk delivered while making cappuccino and milk based coffees Dial position Description Recommended for CP No froth FLAT WHITE MILK hot milk Cp Min froth LATTE P Max froth CAPPUCCINO MILK frothed milk Making milk based drinks automatically The FLAT WHITE CAPPUCCINO LATTE and MILK buttons on the control panel enable these drinks to be prepared automatically Proceed as follows 1 Fill the milk container and attach it as described above 2 Turn the froth adjustment dial on the milk container lid to the position corresponding to the required froth 3 Press the button corresponding to the required drink The name of the drink selected is displayed together with a progress bar which gradually fills as preparation progress 6 4 After a few seconds frothed milk is delivered from the milk spout into the cup below For drinks with coffee the machine automatically makes the coffee after delivering the milk Please note If you want to interrupt preparation during delivery press any button At the end of delivery to increase the quantity of milk or coffee in the cup within three seconds just press and hold the button corresponding to the cappuccino or milk based coffee being made Do not leave the milk container out of the refrigerator for long periods The warmer the milk 5 C is idea
26. fee To modify this quantity proceed as follows 1 Place a cup under the coffee spouts fig 12 2 Press the Co gl button fig 10 until MY COFFEE is displayed 3 Press and hold the button fig 15 until the mes sage Program quantity 1 MY COFFEE is displayed and coffee delivery begins Release the button 4 As soon as the coffee in the cup reaches the required level press the button fig 15 again The quantity of coffee in the cup set has now been pro grammed Adjusting the coffee mill The coffee mill is set by default to prepare coffee correctly and should not require regulating initially However if after making the first few coffees you find that the coffee is either too weak and not creamy enough or delivery is too slow a drop at a time this can be corrected by adjusting the grinding adjustment dial fig 13 i Please note The grinding adjustment dial must only be turned when the coffee mill is in operation If the coffee is delivered too slowly or not at all turn one click clockwise to wards 7 For fuller bodied creamier coffee turn one dick anticlockwise towards 1 do not turn more than one click at a time otherwise the coffee could be delivered a drop at a time These adjustments will only be evident after at least 2 cups of coffee have been delivered If this adjustment does not obtain the desired result turn the dial another click Tips for a hotter
27. follow the instructions below Installing the filter 37 1 Remove the filter from the packaging 2 Turn the date indicator disk see fig 37 until the next two months of use are displayed Ci Please note The filter lasts about two months if the appliance is used normally If the coffee machine is left unused with the filter installed it will last maximum of three weeks 3 activate the filter put it under tap water until the water overflows the k side openings for more than one minute min 500ml fig 38 4 Extract the tank from the appliance and fill with water 5 Place the filter in the water tank and sub merge it completely for ten seconds tilting it to enable the air bubbles to escape fig 39 6 Insert the filter into the filter housing and press as far as it will go fig 40A 7 Close the tank with the lid fig 40B and then replace the tank in the machine When you install the filter you must notify the appliance of its presence 8 Press the MENU ESC button to enter the menu 9 Press the scrolling arrow lt or gt fig 9 until Install filter is displayed 10 Pressthe 0 button 11 Install is displayed 12 Press the amp button to confirm the selection Wa ter delivery Press OK is displayed 13 Position a container under the hot water spout min ca pacity 100 ml 14 Press the amp OK button to confirm th
28. fore insertion squeeze the two levers shown in the figure to make it smaller 8 9 Large lever Once inserted make sure the two red buttons have snapped out Close the infuser door 10 Replace the water tank Cleaning the milk container Clean the milk container each time you prepare milk as de scribed below 1 2 Remove the lid Remove the milk spout and intake a tube Tum the froth adjustment dial clockwise to the INSERT position see figure and pull der off upwards Wash all the com ponents thoroughly with hot water and i mild washing up liquid All compo nents are dishwash er safe placing them in the top basket of the dishwasher Make sure there are no milk residues on the hollow and groove under the dial see figure alongside If necessary scrape the groove with a toothpick Rinse inside the froth adjustment dial seat with running groove recess water see figure 6 Check that the intake tube and spout are not clogged with milk residues 7 Replace the dial lining up the ya arrow with the word INSERT the spout and the milk intake tube f 8 Place the lid back on the milk q 8 container Cleaning the hot water steam nozzle Each time you prepare milk clean the nozzle with a sponge to remove milk residues from the gaskets DESCALING Descale the machine when the message DESCALE and the rel
29. h fresh wa ter and replace the tank Cleaning the coffee spouts 1 Clean the coffee spouts regularly with a sponge or cloth fig 32 2 Check the holes in the coffee spout are not blocked If nec essary remove coffee deposits with a toothpick fig 33 Cleaning the pre ground coffee funnel Check regularly about once a month that the pre ground cof fee funnel A4 is not blocked If necessary remove coffee deposits with the brush D2 sup plied Cleaning the infuser The infuser 19 must be cleaned at least once a month A Important The infuser may not be ex tracted when the machine is on 1 Make sure the machine is correctly turned off see Turning off page 10 34 2 Open the infuser door fig 34 on the right side of the appliance 4 Press the two red release buttons inwards and at the same time pull the infuser outwards fig 35 5 Soak the infuser in water for about 5 minutes then rinse under the tap A Important RINSE WITH WATER ONLY NO WASHING UP LIQUID NO DISH WASHER Do not use washing up liquid to clean the infuser as it may damage it 6 Use the brush D2 to remove any coffee residues left in the infuser housing visible through the infuser door 7 After cleaning replace the infuser by sliding it onto the internal support then push the PUSH symbol fully in until it clicks into place i Please note If the infuser is difficult to insert be
30. he appliance o Please note Coffee has been used to factory test the appliance and it is therefore completely normal for there to be traces of cof feeinthe mill The machine is however guaranteed to be new You should customise water hardness as soon as possible following the instructions in the section Setting water hardness on page 19 1 Plug the power cable connector into the socket at the back of the appliance and connect the appliance to the mains electricity supply fig 1 Make sure the main switch at the side ofthe appliance is pressed fig 2 You must first choose the language the languages scroll through at intervals of about 3 seconds 2 When English appears press and hold the button fig 3 for a few seconds until English set is dis played Follow the instructions indicated on the appliance display 3 FILL TANK remove the water tank fig 4 open the lid fig 5 fill to the MAX line with fresh water fig 6 re place the lid and put the tank back in the appliance 4 INSERT WATER SPOUT Check that the hot water spout is inserted on the nozzle and place a container with a mini mum capacity of 100 ml underneath fig 7 5 Water delivery Press OK is displayed 6 Press the amp OK button to confirm fig 3 The appli ance delivers water from the spout then goes off auto matically The coffee machine is now ready for normal use 9 Please note When setting up
31. id producing milk with poor froth or large bubbles always clean the milk container lid and hot water nozzle as described in the section Cleaning the milk container on pages 15 and 18 Filling and attaching the milk container 1 Remove the lid by pressing the release button C4 and at the same time lifting the lid upwards fig 19 2 Fill the milk container with a sufficient quantity of milk not exceeding the MAX level marked on the container fig 20 Each mark on the side of the container corresponds to about 100 ml of milk o Please note For a denser more even froth you must use skimmed or partially skimmed milk at refrigerator temperature about 50 If Energy saving mode is enabled you may have to wait a few seconds before the drink is delivered 3 Make sure the milk intake tube is correctly inserted in the bottom of the milk container lid fig 21 4 Replace the lid on the milk container and press down wards until it clicks in place 5 Extract the hot water spout by pressing the button on the spout fig 22A 6 Attach the milk container to the nozzle and push as far as it will go fig 23 The machine emits a beep if the beep function is enabled 7 Placeasufficiently large cup under the coffee and frothed milk spouts Adjust the length of the milk spout To move it nearer the cup simply pull it downwards fig 24 8 Follow the instructions below for each function Adjusting the amount o
32. ing the grinding adjustment dial another click until delivery is correct see the section Adjusting the coffee mill on page 13 INSERT GROUNDS CONTAINER After cleaning the grounds container has not been repla ced Remove the drip tray and insert the grounds container ADD PRE GROUND COFFEE The pre ground coffee function has been selected without placing any pre ground coffee in the funnel Place pre ground coffee in the funnel or deselect the pre ground function fig 18 DESCALE The machine must be descaled The descaling procedure described in the section Descaling needs to be performed as soon as possible page 18 REDUCE COFFEE AMOUNT Too much coffee has been used Selecta milder taste by pressing the aroma selection 9 44 button fig 10 or reduce the quantity of pre ground coffee FILL BEANS CONTAINER The coffee beans have run out Fill the beans container fig 14 The pre ground coffee funnel is clogged Empty the funnel with the help of a brush as described in the section Cleaning the pre ground coffee funnel INSERT INFUSER ASSEMBLY The infuser has not been replaced after cleaning Insert the infuser as described in the section Cleaning the infuser INSERT TANK The tank is not correctly in place Insert the tank correctly and press as far as it will go GENERAL ALARM The inside of the appliance is very dirty Clean the inside of the appliance
33. kimmed milk at refrigerator temperature about 5 C For a creamier froth rotate the container with slow move ments in an upward direction To avoid milk with poor froth or large bubbles always clean the spout as described in the following section Cleaning the spout after use Always clean the spout after use to avoid the build up of milk residues and prevent the spout from clogging 1 Place a container under the cappuccino maker and press the amp button to deliver a little water fig 3 Stop the flow of hot water by pressing the 0 button again 2 Wait a few minutes for the cappuccino maker to cool down then press the button on the hot water spout and extract it Hold the spout with one hand and with the other turn the cappuccino maker anticlockwise fig 22 and pull downwards to remove 3 Also remove the steam nozzle by pulling it downwards fig 27 4 Check the hole shown by the arrow in fig 27B is not blocked If necessary clean with a pin 5 Wash all parts of the cappuccino maker thoroughly with a sponge and warm water 6 Reinsert the nozzle and replace the cappuccino maker on the nozzle pushing it upwards and turning it until it is at tached CLEANING A Important Do not use solvents abrasive detergents or alcohol to clean the coffee machine With De Longhi superauto matic bean to cup espresso and cappuccino machines you need not use chemical products to clean the machine None
34. l the poorer the quality of froth produced Clean the milk frother by using the CLEAN button N Important Danger of burns When cleaning the internal tubes of the milk container a little hot water and steam leak out of the frothed milk spout Avoid contact with splashes of water TURN DIAL TO CLEAN flashes on the display each time you use a milk function To eliminate all milk residues proceed as follows 1 Leavethe milk container in the machine you do not need to empty it 2 Place a cup or other recipient under the frothed milk spout 3 Turn the froth adjustment dial to CLEAN fig 25 Clean ing underway Please wait is displayed together with a progress bar which gradually fills as the operation pro ceeds Cleaning stops automatically 4 the dial back to one of the froth selections 5 Remove the milk container and always clean the steam nozzle with a sponge fig 26 0 Please note To prepare a number of cappuccinos and milk based cof fees clean the milk container after you have prepared the last drink only The milk container can be kept in the refrigerator nsome cases to clean you must wait for the appliance to heat up Programming the quantity of coffee and milk in the cup for the FLAT WHITE CAPPUCCINO LATTE and MILK buttons The appliance is set by default to automatically deliver stand ard quantities To change these quantities proceed as follows 1 Place a cup under
35. ow lt or gt fig 9 until Beep is displayed 3 Press the 0 ok button Disable is displayed or En able if disabled 4 Press the 0 button to enable or disable the beep 5 Press the MENU ESC button to exit the menu Cup lighting This function enables or disables the cup lighting The lighting is enabled by default The lighting comes on each time coffee cappuccino or milk based coffee is made and during each rinsing cycle To disable or re enable this function proceed as follows 1 Press the MENU ESC button to enter the menu 2 Press the scrolling arrow lt or gt fig 9 until Cup light ing is displayed 3 Press the 0 button Disable is displayed or En able if disabled 4 Press the 0 oK button to enable or disable the cup lighting 5 Press the MENU ESC button to exit the menu Default values reset This resets all menu settings and programmed quantities back to the default values with the exception of the language which remains as set To reset the default values proceed as follows 1 Press the MENU ESC button to enter the menu 2 Press the scrolling arrow lt or gt fig 9 until Default values is displayed 3 Press the button 4 Confirm is displayed 5 Pressthe 0 button to confirm and exit Statistics function This displays statistics relating to the machine To display proceed as follo
36. per D8 Descaler BEFORE USE Checking the appliance After removing the packaging make sure the product is com plete and undamaged and that all accessories are present Do not use the appliance if it is visibly damaged Contact De Longhi Customer Services Installing the appliance A Important When you install the appliance you should follow the safety warnings below The appliance gives off heat After positioning the appli ance on the worktop leave a space of at least 3 cm be tween the surfaces of the appliance and the side and rear walls and at least 15 cm above the coffee machine Water penetrating the appliance could cause damage Do not place the appliance near taps or sinks The appliance could be damaged if the water it contains freezes Do not install the appliance in a room where the temperature could drop below freezing point Arrange the power cable in such a way that it cannot be damaged by sharp edges or contact with hot surfaces e g electric hot plates Connecting the appliance A Important Check that the mains power supply voltage corresponds to the value indicated on the rating plate on the bottom of the ap pliance Connect the appliance to an efficiently earthed and correctly installed socket with a minimum current rating of 10A only If the power socket does not match the plug on the appliance have the socket replaced with a suitable type by a qualified professional Setting up t
37. s are identified by these symbols It is vital to follow these warnings Danger Failure to observe the warning may result in life threatening injury by electric shock A Important Failure to observe the warning could result in injury or damage to the appliance A Danger of burns Failure to observe the warning could result in burns g Please note This symbol identifies important advice or information for the user Letters in brackets The letters in brackets refer to the legend in the description of the appliance on page 2 3 Troubleshooting and repairs In the event of problems first try and resolve them following the information given in the sections Displayed messages on page 21 and Troubleshooting on page 22 If this does not resolve the problem or you require further in formation you should consult customer services by calling the number given on the annexed guarantee leaflet If your country is not among those listed on the sheet call the number given in the guarantee leaflet If repairs are required contact De Longhi customer services only The addresses are given in the guarantee leaflet provided with the machine SAFETY Fundamental safety warnings Danger This is an electrical appliance and may cause electric shock You should therefore follow the safety warnings below Never touch the appliance with damp hands or feet Never touch the plug with damp hands Make sure
38. t for a hardness value of 4 The machine can also be programmed according to the hard ness of the mains water in the various regions so that the ma chine needs to be descaled less often Measuring water hardness 1 Remove the TOTAL HARDNESS TEST indicator paper at tached to these instructions from its pack 2 Immerse the paper completely in a glass of water for one second 3 Remove the paper from the water and shake lightly After about a minute 1 2 3 or 4 red squares form depending on the hardness of the water Each square corresponds to one level soft water slightly hard water hard water veryhard water MMN TH Setting water hardness 1 Press the MENU ESC button to enter the menu 2 Press the scrolling arrow lt or gt until Water Hardness is displayed 3 Press the OK button to confirm the selection 4 Press the scrolling arrow or gt repeatedly to set the level as measured by the indicator paper see previous section 5 Press the 0 button to confirm the setting 6 the MENU ESC button to exit the menu The machine is now reprogrammed with the new water hard ness setting 2 WATER SOFTENER FILTER Certain models are fitted with a water softener filter If this is not the case with your model you are recommended to pur chase one from De Longhi Customer Services To use the filter correctly
39. the appliance you need to make 4 5 cups of coffee or 4 5 cappuccinos before the appliance starts to give satisfactory results To enjoy your coffee even more and improve the perform ance of your appliance we recommend installing a water softener filter as described in the section WATER SOFTEN ER FILTER page 19 If your model is not provided with a filter you can request one from De Longhi Customer Services TURNING THE APPLIANCE ON i Please note Before turning the appliance on make sure the main switch is pressed fig 2 Each time the appliance is turned on it performs an automatic preheat and rinse cycle which cannot be interrupted The appli ance is ready for use only after completion ofthis cycle A Danger of burns During rinsing a little hot water comes out of the coffee spouts and is collected in the drip tray underneath Avoid contact with splashes of water To turn the appliance on press the ON STANDBY d button fig 8 The message Heating up Please wait is displayed After heating the message RINSING is displayed As well as heating the boiler the appliance also heats the internal circuits by circulating hot water The appliance is at temperature when the message indicating the taste and quantity of coffee appears TURNING THE APPLIANCE OFF ________ Whenever the coffee machine is turned off after being used to make coffee it performs an automatic rinse cycle A Danger o
40. usehold appliance only Itisn ded to be used in kitchen areas in shops offices and other working lonments houses by clients in hotels motels and other residential type en vironments bed and breakfast type environments INSTRUCTION FOR USE Read these instructions carefully before using the appliance Failure to follow these instructions may result in burns or damage to the appliance The manufacturer is not liable for damage deriving from failure to follow these instructions i Please note Keep these instructions Ifthe appliance is passed to other per Sons they must also be provided with these instructions DESCRIPTION Description of appliance page3 A 1 A2 Beans container A3 Pre ground coffee funnel lid with pressure closure M Pre ground coffee funnel A5 Beans container lid A6 Grinding adjustment dial A7 Water tank A8 Water tank extraction handle A9 Water softener filter housing A10 Cup warmer shelf A11 Coffee spout adjustable height A12 Hot water and steam nozzle A13 Socket for power cable connector A14 Condensate tray A15 Cup tray A16 Drip tray A17 Drip tray water level indicator A18 Coffee grounds container A19 Infuser A20 Main switch A21 Infuser door A22 Infuser door catch A23 b button turns the appliance on and off stand by A24 Y button to enable or disable the cup warmer ANN Description of control panel p
41. ws 1 Press the MENU ESC button to enter the menu 2 Press the scrolling arrow lt or gt fig 9 until Statistics is displayed 3 Press the 0 oK button 4 By pressing the scrolling arrow lt or gt fig 9 you can check how many coffees have been made thetotal number of cappuccinos and milk based coffees the total number of litres of water delivered how many times the machine has been descaled how many times the water softener filter has been re placed 5 the MENU ESC button twice to exit the menu MAKING COFFEE Selecting the coffee taste The appliance is set by default to make coffee with a standard taste You can also choose one of these tastes Extra mild taste Mild taste Standard taste Strong taste Extra strong taste To change the taste press the 06 button fig 10 re peatedly until the required taste is displayed Selecting the quantity of coffee in the cup The appliance is set by default to make a standard quantity of coffee To select the quantity of coffee press the C ug button fig 11 until the message corresponding to the re quired quantity of coffee is displayed Coffee selected Quantity in cup ml MY COFFEE Programmable from 20 to 180 SHORT 40 STANDARD 60 LONG 290 EXTRA LONG 120 Customising the my coffee quantity The appliance is set by default to automatically deliver 30 ml of cof
Download Pdf Manuals
Related Search