De'Longhi Coffeemaker EC860 User's Manual
Contents
1. page 2 D D1 Filter holder cup D2 1 coffee crema filter D3 2 coffee crema filter D4 ESE pod crema filter D5 Power supply cable removable D6 Tamper dispenser measure Description pr D7 Removable water steam spout D8 Reactive strip to detect water hardness Total hardness test D9 Descaler D10 Water softener filter Instructions for use Read these instructions carefully before using the appliance Failure to respect these instructions may result in personal injury or damage to the appliance The manufacturer is not liable for damage as a result of failure to comply with these user instructions 0 Please note Keep these instructions If the appliance should be transferred to other persons these instructions must accompany it Checking the appliance After the packaging has been removed check the integrity of the appliance and the presence of all accessories Do not use the appliance if it is visibly damaged Contact the Customer Experience Installing the appliance A Attention The following safety measures must be complied with when installing the appliance The appliance could be damaged by water infiltration Do not position the appliance near water faucets or sinks The appliance could be damaged if the water it contains freezes Do not install the appliance in a room where the temperature can fall below freezing point Position the power supply cable in a way that it cannot be damag2. 5 Remove the hot water spout from the nozzle by pushing the button fig 20 6 Attach by inserting the container to the nozzle fig 21 7 Set up the machine to make coffee see how to prepare espresso pg 10 8 Place the cup for cappuccino or the glass for Latte Macchiato under the coffee spout and adjust the milk spout fig 22 If using tall cups or glasses reposition the cup holder as shown in fig 23 9 Vary the froth regulator depending on the amount of froth wanted and type of milk used fig 24 To prepare the Cappuccino press button To prepare the latte macchiato press button 9 After having delivered the frothed milk the machine automatically prepares the coffee Please note For a hotter cappuccino it is advised to press the CLEAN button to heat the ducts of the milk frother device see successive paragraph To prepare the cappuccino or the latte macchiato the appliance performs 2 deliveries first the milk and subsequently the coffee If you would like to interrupt the delivery in progress press the previously pressed button Once delivery is completed if wanting to increase the amount of milk or coffee inside the cup keep the button within a few seconds relative to the preparation in progress pressed Do not leave the milk container out of the refrigerator for too long the higher the milk temperature 41 F 5 C is ideal the poorer the quality of the froth Cl
3. it should breakdown Switch the appliance off remove the plug from the socket and contact the After Sales Technical Assistance If the plug or power supply cable are damaged have them replaced exclusively by the De Longhi After Sales Service in order to avoid risks During cleaning never immerse the machine in water it is an electric appliance Before performing any cleaning operations to the external parts of the appliance switch the machine off remove the plug from the socket and let the machine cool down Safety warnings 3 A Attention Keep the packaging material plastic bags expanded polystyrene out of the reach of children A Attention Do not allow the appliance to be used by persons including children with reduced psycho physical sensorial capacities or that have insufficient experience and knowledge unless they are carefully monitored and trained by a person responsible for their safety Watch children do not let them play with the appliance A Scalding hazard This appliance produces hot water and steam may form during operation Pay attention not to come into contact with hot water sprays or steam Do not touch the cup holder when the appliance is on because it can get Complying with intended use This appliance is manufactured for the preparation of coffee and to heat beverages This appliance is intended exclusively for domestic use It is not intended for the use in rooms used as kitchens for perso
4. De Longhi Appliances via Seitz 47 31100 Treviso Italia 5713218341 12 11 Printed in China Instructions foruse COFFEE MAKER D Symbols used in these instructions The important recommendations have these symbols These warnings must be followed A Danger Failure to comply can be or is the cause of injury due to life threatening electric shocks A Attention Failure to comply can be or is cause of injury or damage to the appliance A Scalding hazard Failure to comply can be or is the cause of scalding or burns g Please note This symbol highlights recommendations and important information for the user Fundamental warnings regarding safety A Danger As the appliance operates using electric current electric shocks can not be excluded Therefore follow the safety recommendations given Do not touch the appliance when you have wet hands or feet Do not touch the plug with wet hands Make sure that the socket used can always be easily reached so that the plug can be removed when required Remove the plug from the socket by pulling directly on the plug itself Do not pull the cable as damage could be caused Remove the plug from the socket to disconnect the appliance completely Do not attempt to repair the appliance if
5. and without mess Insert the filter for pods coffee D4 in the filter holder fig 10 e Insert the pod centering it as close as possible on the filter fig 16 Always follow the instructions of the pod pack for correct positioning of the pod in the filter Attach the filter holder to the machine for correct attachment align the filter holder handle to symbol OPEN fig 13 attach the filter holder and turn handle to the right until aligned to position WCLOSE fig 14 Position the cup under the filter holder spouts It is advised to heat the cup before making the coffee rinsing it with hot water Ensure the lights relative to the coffee buttons are on press the coffee button the appliance proceeds and interrupts automatically Please note While the machine is preparing the coffee it can be stopped at any time by pressing the previously pressed coffee button Once delivery is completed if you would like to to increase the amount of coffee inside the cup keep the previously pressed coffee button pressed within 3 seconds of delivery Turn the handle from right to left to release the filter holder A Scalding hazard To avoid sprays never release the filter holder while the machine is delivering and wait a few seconds after delivery Program the amount of coffee in the cup The machine has been set by default to deliver standard amounts of coffee If you would like to amend to amend these
6. e drip tray Cleaning the coffee filters Regularly clean the coffee filters rinsing them under running water Check that the holes are not blocked If they are clean them using a pin fig 28 Cleaning the boiler outlet Rinse the boiler outlet every 200 coffees delivered by delivering 0 51 of water from the boiler outlet place a cup under the boiler outlet and then press either the 1 or 2 cup coffee button to deliver a coffee without using coffee powder Cleaning the milk container Clean the milk container after each milk preparation as described below 1 Extract the lid 2 Remove the milk spout tube and the intake tube fig 29 3 Remove the froth regulator by by pulling it out fig 30 4 Carefully clean all components using hot water and a mild detergent All components can be washed in the dishwasher by positioning them on the upper rack of the dishwasher Pay particular attention that milk residues do not remain inside the holes and in the groove on the narrow part of the froth regulator 5 Also check that the intake tube and the milk spout tube are not obstructed by milk residues 6 Re assemble the froth regulator the milk spout tube and the milk intake tube 7 Place the lid on the milk container Replacing the filter After two months of duration see calendar or if the appliance is not used for 3 weeks replace the filter as described in paragraph Activation of the softener filter and filling of th
7. e tank page 9 13 Instructions for usery Descaling Descale the machine when the light flashes on the control panel Proceed as follows 1 Remove the water filter Fill the tank with the descaling solution obtained by diluting the descaler with water as indicated on the descaler pack 2 Insert the hot water spout fig 8 3 Place one container under the boiler outlet and one under the hot water spout fig 31 and ensure the drip tray is empty and correctly inserted 4 Simultaneously press and buttons light turns on if the hot water spout has not been inserted the light flashes 5 Press the button Descaling is signaled by the LED that alternate in sequence The descaling program automatically performs a series of deliveries from the boiler outlet and from the hot water spout at intervals to remove the lime scale from inside the coffee machine 6 the descaling solution is terminated the light turns on to indicate rinsing is necessary 7 Toeliminate the solution and lime scale residues rinse the tank and fill it with fresh water without descaler empty the containers and place them under the boiler outlet and hot water spout 8 Press the button rinsing starts and all LEDs flash in sequence 9 Rinsing stops when the tank is empty rinse and refill the tank 10 Light on press the relative button delivery starts and interrupts automatically The appliance is now ready
8. eaning the milk frother device using the CLEAN button After every use of the milk functions perform cleaning to eliminate the milk residues as follows 1 Leave the milk container inserted in the machine it is not necessary to empty the milk container 2 Place a cup or other container under the milk spout tube 3 the CLEAN button fig 25 pressed lights and flash When the lights stop flashing and the appliance goes back to ready for use release the CLEAN button the steam cleans the circuits inside the milk frother Program the amount of coffee and milk in the cup for cappuccino or milk The machine has been set by default to deliver standard amounts of coffee and milk If you would like to amend these quantities proceed as follows 1 Place a cup under the coffee spouts and the milk spout tube 2 Press the button relative to the preparation with milk to be programmed and keep it pressed After a few seconds the machine starts delivering the milk 3 the required quantity of milk has been delivered into the cup release the button milk delivery stops 4 Program the amount of coffee into the cup as for the amount of milk 5 Programming is confirmed by the lights flashing for 3 seconds The machine is now re programmed according to the new amounts of milk and coffee Preparing the hot water and steam A Scalding hazard Do not leave the machine unattended when delivering ho
9. ed by sharp edges or by contact with hot surfaces e g electric stoves cooking surfaces or gas burners Connecting the appliance A Attention Make sure that the electric mains voltage corresponds with that indicated on the data plate on the base of the appliance Insert the power supply cable connector in the socket on the back of the appliance fig 1 then insert the plug in the power outlet Check that the mains power supply voltage corresponds to the value indicated on the rating plate on the bottom of the appliance If the power socket does not match the plug on the appliance have the socket replaced with a suitable type by a qualified professional Activation of the water filter and filling of the water tank Remove the filter from the packaging and rinse t with about 17 07 0 5 L of running water fig 2 Turn the calendar disc see fig 3 until the following 2 months of use are displayed 0 Please note the filter has a two month duration if the appliance is used normally whereas if the machine remains unused with the filter installed it has a maximum 3 month duration Remove the water tank and fill it with fresh water do not exceed the MAX line fig 4 Completely dip the filter in the water tilting it to enable air bubbles to come out fig 5 Insert the filter in the appropriate seat fig 6 press down and close the tank with the lid Place the tank back into the machine Ensure the water level is not o
10. for use Repairs to the coffee machine relative to lime scale problems are not covered by the warranty if the descaling procedure described above is not performed on a regular basis Troubleshooting gg Problem Possible causes Solution The device will not switch on The power supply cable is not inserted correctly Check that the power supply cable connector is fully inserted in the appropriate socket on the back of the device then check that the plug is correctly connected to the power outlet Espresso coffee does not flow out No water in the tank Fill the water tank The holes in the filter holder are blocked Clean the holes in the filter holder spouts The espresso boiler outlet is blocked Clean as indicated in the Cleaning the boiler outlet paragraph page 13 Espresso coffee drips from the edges of the filter holder instead of through the holes The filter holder is not correctly inserted oris dirty Attach the filter holder correctly and handle to the right until aligned to the CLOSE position The espresso boiler gasket has lost elasticity or it is dirty The holes in the filter holder spout are blocked Have the espresso boiler gasket replaced at a service center Clean the holes in the filter holder spouts The filter holder does not hook onto the device Too much coffee was poured in the filter Use the measure provided and make sure to use the correct fil
11. he programming menu 2 Keep button pressed until the lights relative to the wanted temperature turn on see chart below 3 When the lights relative to the wanted temperature turn on release the button 4 Press to turn the appliance off stand by Adjust Stand by The machine is pre set to switch to stand by after 75 minutes of non use This time interval can be modified so that the appliance switches off after 15 minutes or after 3 hours Proceed as follows 1 Access the programming menu 2 Keep the button pressed until the lights relative to the desired stand by interval turn on see chart below 3 When the lights relative to the wanted stand by interval turn on release the button 4 Press to turn the appliance off stand by Setting temperature and Adjust Stand by chart Temperature Corresponding lights Stand by after Low 15 minutes Medium 75 minutes High 3 hours Z Set the water hardness The lights signaling the need to descale the appliance after a pre set period of operation depends on the hardness of the water It is possible to program the machine according to the actual water hardness in use in the area thus making descaling less frequent Proceed as follows 1 Remove the provided reactive strip TOTAL HARDNESS TEST from its packaging 2 Completely dip the strip into glass of water for one second 3 Remove the strip from the water and shake it slightl
12. iler outlet page13 The filter is blocked Perform cleaning as indicated in the section cleaning the coffee filters The machine does not work and all lights flash Immediately disconnect the appliance and contact an authorized service center 15
13. n cleaning the filter page 13 The coffee is too finely ground Only use coffee ground specifically for espresso coffee machines The ground coffee is too fine or is damp Only use coffee ground specifically for espresso coffee machines and it must not be too damp Incorrect type of ground coffee Change the quality of the ground coffee powder The milk does not froth when making a cappuccino The milk is not cold enough Always use milk at refrigerator temperature The cursor of the milk frother lid is not in correct position Ensure the cursor is in the froth position The milk container lid is dirty Clean the milk lid as described in the section Cleaning the milk container page 13 The milk contains large bubbles and there is little froth The machine does not deliver any drink and the lights flash for few seconds The spout is dirty No water in the tank Clean as described in the section Cleaning the spout after use Fill the water tank The tank is inserted incorrectly and the valve on the bottom is not open Press the tank lightly to open the valve on the bottom Incorrectly installed water filter Activate the filter by following the indicated procedure The ground coffee is too tightly pressed Press the coffee less The espresso boiler outlet is blocked Perform cleaning as indicated in the section cleaning the bo
14. nnel in shops offices and other work areas farm holidays hotels motels and other reception structures guest houses Any other use must be considered improper and therefore dangerous The manufacturer is not liable for damage deriving from improper use of the appliance 1148 Functioning lights ym Lights operation Meaningoflights Turn on from general ON OFF switch at the back of the appliance The appliance performs a self test signalled by the sequential flashing of lights The appliance is on no accessory is connected to coupling A2 The appliance is heating up to make coffee when the 1 or 2 cup lights stop flashing the appliance has reached the ideal temperature to deliver coffee ES The appliance is the hot water spout The appliance is heating up to make D7 is connected to coupling A2 coffee or to deliver hot water when the 1 or 2 cup lights and the hot water spout light stop flashing the appliance has reached the ideal temperature to deliver coffee or hot water The appliance is the milk container C The appliance is heating up to make isconnected to coupling A2 coffee cappuccino or latte macchiato when the 1 or 2 cup lights the o cappuccino and latte macchiato lights o stop flashing the appliance has reached e ideal temperature to deliver coffee or latte macchiato The appliance has been for 75 min
15. ntaining the liquid to avoid burns from splashes Cleaning the water spout after use Always clean the spout after use to avoid the build up of milk residues and prevent the spout from clogging 1 Place a container under the cappuccino maker and press the button to deliver a little water fig 3 Stop the flow of water by pressing the button again 2 Wait a few minutes for the cappuccino maker to cool down then extract the hot water spout 3 Check the hole is not blocked If necessary clean with a pin 4 Wash all parts of the cappuccino maker thoroughly with sponge and warm water 5 Reinsert the water spout Cleaning A Attention Do not use solvents abrasive detergents or alcohol to clean the machine Only the milk container D can be washed in the dish washer No other part of the appliance can be washed in the dishwasher Do not use metal objects to remove coffee deposits or fouling as they might scratch the metal or plastic surfaces Cleaning the drip tray A Attention The drip tray is equipped with a floating water level indicator red A11 As soon as this indicator starts protruding from the cup tray empty the tray and clean it otherwise the water may overflow and damage the machine and the surrounding work top 1 Remove the drip tray fig 26 2 Remove the cup tray dispose of the water fig 27 and clean the tray using a cloth then re assemble the drip tray 3 Re insert th
16. of ground coffee about 0 48 0z 7 7 gr Fill the filter a little at a time to prevent the ground coffee from overflowing Attention For correct use before filling the filter with ground coffee always make sure there is no residual coffee from the previous infusion in the filter Distribute the ground coffee evenly and press it lightly using the coffee tamper fig 12 Pressing the ground coffee is very important to obtain a good espresso If excessively pressed the coffee will slowly leak and it will be stronger Whereas if slightly pressed the coffee will come out too quickly and will be light Remove any excess coffee from the rim of the filter holder and attach it to the machine for correct attachment align the filter holder handle to symbol OPEN fig 13 attach the filter holder and turn handle to the right until aligned to position WCLOSE fig 14 e Position the cup or cups under the filter holder spouts fig 15 It is advised to heat the cups before making the coffee rinsing them with hot water Ensure the lights relative to the coffee buttons are on press the coffee buttons or the appliance proceeds and interrupts automatically How to prepare espresso using pods Please note use pods that comply with the ESE Standard this will be indicated on the packaging by the following mark The ESE Standard is a system accepted by leading coffee pod manufacturers and allows espresso coffee to be made simply
17. quantities proceed as follows 1 Place a cup under the coffee spout 2 Keep the button to be programmed or e pressed The machine starts delivering coffee 3 As soon as the wanted amount of coffee in cup is reached release the button delivery stops The machine is now re programmed according to the new amount Warmer cup fig 32 The warmer cup can be switched on by pushing the but ton leave the cups on the appliance as long as they are warm This is useful to have warmer coffee A Important When the appliance turns to low power function or stand by the cup warmer is still on until you don t press the button to switch it off Pay attention not to touch it as it is hot How to prepare milk based drinks To avoid milk with poor froth or large bubbles always clean the lid of the milk and the hot water nozzle as described in the cle aning the milk container at page 13 1 Remove the lid fig 17 2 Fill the milk container with sufficient amount of milk not 11 Instructions for usery exceeding the maximum of 0 5 I fig 18 Remember that every notch on the side of the container corresponds to 100 ml of milk g Please note For a more dense and homogenous froth It is recommended to use skim milk at refrigerator temperature about 41 F 5 C 3 sure the milk intake tube is correctly inserted in the bottom of the milk container lid fig 19 4 Place the lid on the milk container
18. t water The spout heats up during delivery therefore only the black part must be held Delivering hot water 1 Check the hot water spout is correctly attached fig 8 2 Place a cup under the spout as near as possible to avoid sprays 3 Press the button B7 the relative light flashes and the appliance starts hot water delivery The machine automatically stops delivery Please note To manually interrupt the hot water delivery press button again Programming the amount of water automatically delivered If you would like to amend the amount of water set by default proceed as follows 1 Place a cup under the water spout Instructions for usery 2 Keep the button pressed 3 When the hot water in the cup reaches the required level release the button Programming is confirmed by the lights flashing for three seconds The machine is now re programmed according to the new amount Delivering steam 1 Check the hot water spout is correctly attached fig 8 2 Filla container with the liquid to be heated frothed and immerse the water steam spout into the liquid 3 Press twice the button B7 the relative light flashes and the appliance starts steam delivery 4 When the required temperature is obtained interrupt steam delivery by pressing the button again You should not discharge steam for more than 3 minutes at a time A Important Always stop steam delivery before extracting the container co
19. ter for the type of preparation desired Loud pump noise The water tank is empty Fill the tank The tank is inserted incorrectly and the valve on the bottom is not open Press the tank lightly to open the valve on the bottom The coffee cream is clear it flows quickly from the spout The ground coffee has not been sufficiently pressed Increase pressing of the ground coffee Not enough ground coffee Increase the amount of ground coffee The coffee is not ground finely enough Incorrect type of ground coffee Only use coffee ground specifically for espresso coffee machines Change the quality of the ground coffee After coffee delivery the coffee filter re mains attached to the boiler outlet Insert the filter holder again then remove it After the coffee has been prepared the pod or coffee powder remains attached to the boiler outlet Re insert the filter holder deliver coffee remove the filter holder Troubleshooting Problem The coffee cream is dark it flows slowly from the spout Possible causes The ground coffee is too tightly pressed Solution Press the coffee less Large amount of ground coffee Decrease the amount of ground coffee The espresso boiler outlet is blocked Perform cleaning as indicated in the section cleaning the boiler outlet page 13 The filter is blocked Perform cleaning as indicated in in the sectio
20. utes for the ON STAND BY button has been pressed The appliance is in STAND BY to switch it back on press the button The time interval before stand by is adjustable see section Adjust Stand by interval The water tank is empty or the appliance cannot deliver See section Troubleshooting page 15 Description of appliance page 3 A A1 Cup holder Warming plate A2 Water spout milk container coupling A3 General ON OFF switch A4 Power supply cable socket 5 Boiler outlet Infusion assembly A6 Watertank seat A7 Watertank lid A8 Watertank with seat for water filter A9 Water refill indicator A10 Drip tray A11 Indicator for drip tray maximum water level 12 Cup tray A13 Sliding tray for long coffee latte macchiato glass A14 Cup warmer button Description of control panel B page 3 B1 ON Stand by Button B2 ON Stand by Light B3 1 cup button B4 1 cup temperature light B5 2 cups button B6 2 cups temperature OK light B7 Hotwater button B8 Hot water light B9 Hot milk cappuccino button B10 Hot milk cappuccino temperature OK light B11 Hot milk latte macchiato button B12 Hot milk latte macchiato temperature OK light Milk container description page 2 0 C1 Milk frother lid with froth regulator CLEAN button G3 Milk Spout Tube 4 Milk intake tube 5 Milk container Description of accessories
21. ver the MAX line fig 7 The filter is now activated and the machine can be used Appliance first use Turn the appliance on by pressing the 1 0 main switch A3 at rear in pos the appliance performs a self test signalled by the sequential flashing of the lights Once the self test is completed the hot water spout light B8 flashes while the others turn off the appliance signals it is necessary to insert the hot water spout fig 8 Place a container underneath the spout with minimum capacity of 100 ml fig 9 Press the hot water button delivery starts and interrupts automatically The coffee and water spout lights flash to indicate the appliance is reaching temperature when the lights stop flashing and remain permanently on the appliance is ready for use Please note upon first use If lights and flash press the button again Upon first use it is necessary to make 4 5 coffees or 4 5 cappuccinos before the machine gives a satisfying results Settings of the programming menu To access the programming menu ensure the appliance is in stand by simultaneously press buttons and until the ON Stand by B2 light flashes the appliance is in programming mode Set the machine as wanted to exit the Instructions for use programming menu press button again Setting the temperature To modify the temperature low medium high of the water used to make the coffee proceed as follows 1 Access t
22. y After about one minute 1 2 3 or 4 red squares form depending on the hardness of the water 4 red squares very hard water Access the programming menu Once obtained the result of the strip keep the hot water button pressed until the lights turn on as in following table tp 6 0000 Ve 000 98 5 When the lights relative to the detected water hardness turn on release the button Press button to turn the appliance off stand by 0 Please note If the water filter is correctly used set the machine on to a lower hardness level compared to that detected by the reactive strip ON OFF and stand by When the main switch is in pos turn the appliance on and off stand by by pressing the button The appliance automatically turns off stand by after 75 minutes of non use to change the non use time refer to paragraph Adjust stand by How to prepare espresso using ground coffee Insert the filter for ground coffee D2 or D3 in the filter holder fig 10 Use the filter 9 if wanting to make e ot one coffee or the filter eo if wanting to make 2 coffees Instructions for usery To prepare one coffee fill the filter with one level measuring spoon of ground coffee about 0 24 0z 7 gr fig 11 If you wish to prepare two cups of coffee fill the filter with two less than level measuring spoons
Download Pdf Manuals
Related Search