Dell PowerEdge M910 Setup Guide
Contents
1. For AC power supply do not plug the power cables directly into a power outlet you must use a PDU For optimal system functionality a minimum of three power supplies are required Plug the other end of the power cables of the AC power supplies into a power distribution unit PDU The system requires a minimum of two PDUs and up to six PDUs depending on the PDU rating Each PDU must be powered to a separate appropriate rated branch circuit protective ground AC power source For DC power supplies plug the other end of the power cables to a branch circuit protective ground DC power source K NOTE All power supplies in the enclosure must be of the same type and have the same maximum output power K NOTE AC and DC power supplies cannot be mixed in an enclosure Turning On The Enclosure Figure 7 Turning on the Enclosure Press the power button on the enclosure The power indicator should light Turning On The Blades Figure 8 Turning on a Blade Press the power button on each blade or power on the blades using the systems management software Complete The Operating System Setup If you purchased a preinstalled operating system see the documentation associated with the operating system To install an operating system for the first time see the installation and configuration documentation for your operating system Be sure the operating system is installed before installing hardware or software not purchased with the system2. Hat Inc in the United States and or other countries Novell and SUSE are registered trademarks of Novell Inc in the United States and other countries Oracle is a registered trademark of Oracle Corporation and or its affiliates Citrix Xen XenServer and XenMotion are either registered trademarks or trademarks of Citrix Systems Inc in the United States and or other countries VMware vMotion vCenter vCenter SRM and vSphere are registered trademarks or trademarks of VMware Inc in the United States or other countries IBM is a registered trademark of International Business Machines Corporation 2013 09 Rev A00 Installation And Configuration A WARNING Before performing the following procedure review the safety instructions that came with the blade server or enclosure NOTE The system is intended for restricted access location in accordance with the National Electric Code National Standards Institute ANSI National Fire Protection Association NFPA 70 Unpacking The System Unpack your blade server or enclosure and identify each item Installing The Enclosure In The Rack Figure 1 Installing the Enclosure in the Rack Assemble the rails and install the enclosure in the rack following the safety instructions and the rail installation instructions that shipped with the rail kit Installing A Sleeve In The Enclosure K NOTE This procedure applies only to PowerEdge M420 A sleeve includes
3. K NOTE See dell com ossupport for the latest information on supported operating systems Dell Software License Agreement Before using your system read the Dell Software License Agreement that came with your system You must consider any media of Dell installed software as BACKUP copies of the software installed on your system s hard drive If you do not accept the terms of the agreement call the customer assistance telephone number For customers in the United States call 800 WWWW DELL 800 999 3355 For customers outside the United States see dell com support and select your country or region from the top left of the page Related Information WARNING See the safety and regulatory information that shipped with your system Warranty information may be included within this document or as a separate document e The Owner s Manual provides information about system features and describes how to troubleshoot the system and install or replace system components This document is available online at dell com poweredgemanuals e The blade Owner s Manuals provide information about the blade features and describe how to troubleshoot the systems and install or replace system components These documents are available online at dell com poweredgemanuals e For the Owner s Manuals and Installation Guides for Dell EqualLogic hardware go to support equallogic com e The CMC User s Guide provides information on installing configuring and using the C
4. Up to 35 C 95 F 35 C to 40 C 95 F to 104 F 20 C h 36 F h 40 C to 65 C 40 F to 149 F 10 C to 35 C 50 F to 95 F with no direct sunlight on the equipment 10 to 80 Relative Humidity with 26 C 78 8 F maximum dew point 5 to 95 RH with 33 C 91 F maximum dew point Atmosphere must be non condensing at all times 0 26 G ms at 5 Hz to 350 Hz all operation orientations 1 87 G ms at 10 Hz to 500 Hz for 15 min all six sides tested One shock pulse in the positive z axis of 31 G for 2 6 ms in all operational orientations Six consecutively executed shock pulses in the positive and negative x y and z axes one pulse on each side of the system of 71 G for up to 2 ms 3048 m 10 000 ft 12 000 m 39 370 ft Maximum temperature is reduced by 1 C 300 m 1 F 547 ft above 950 m 3 117 ft Maximum temperature is reduced by 1 C 175 m 1 F 319 ft above 950 m 3 117 ft Environmental 40 C to 45 C 104 F to 113 F Maximum temperature is reduced by 1 C 125 m 1 F 228 ft above 950 m 3 117 ft Particulate Contamination K NOTE This section defines the limits to help avoid IT equipment damage and or failure from particulates and gaseous contamination If it is determined that levels of particulates or gaseous pollution are beyond the limits specified below and are the reason for the damage and or failures to your equipment it may be nece
5. Width Depth Weight maximum PowerEdge M520 Height Width Depth Weight maximum PowerEdge M420 Sleeve Height Width Depth Weight Blade Height Width Depth Weight maximum 48 6 cm 19 2 inch 14 5 kg 31 9 Ib 38 5 cm 15 2 inch 5 cm 2 inch 48 6 cm 19 2 inch 11 1 kg 24 5 Ib 18 9 cm 7 4 inch 5 cm 2 inch 48 6 cm 19 2 inch 7 4 kg 16 3 Ib 18 9 cm 7 4 inch 5 cm 2 inch 48 6 cm 19 2 inch 5 2 kg to 6 4 kg 11 5 Ib to 14 0 Ib 18 9 cm 7 4 inch 5 cm 2 inch 48 6 cm 19 2 inch 6 4 kg 14 1 Ib 39 5 cm 15 6 inch 5 cm 2 inch 44 3 cm 17 4 inch 3 kg 6 61 Ib 9 75 cm 3 8 inch 5 cm 2 inch 45 8 cm 18 inch 2 3 kg 5 07 Ib 11 Physical Enclosure Height Width Depth Weight maximum Weight empty Environmental 44 0 cm 17 3 inch 44 7 cm 17 6 inch 75 5 cm 29 7 inch 200 5 kg 442 Ib 44 6 kg 98 1 Ib NOTE For additional information about environmental measurements for specific system configurations see dell com environmental_datasheets Temperature Maximum Temperature Gradient Operating and Storage Storage Temperature Limits Temperature Continuous Operation Temperature Ranges for altitude less than 950 m or 3117 ft Humidity Percentage Range Relative Humidity Storage Maximum Vibration Operating Storage Maximum Shock Operating Storage Maximum Altitude Operating Storage Operating Altitude De rating
6. up to four quarter height blades to function as a system Depending on your order the sleeve may ship with the blades preinstalled A CAUTION Exercise utmost care when installing or removing the sleeve to prevent damage to the internal components To ensure protection for the electronic components inside follow the Electrostatic Discharge ESD guidelines Figure 2 Installing a Sleeve NOTE Before you install or remove a sleeve from the enclosure ensure that the top slot of the sleeve Blade a is empty You can install a blade in the top slot Blade a after you install the sleeve in the enclosure Remove the orange cover from the sleeve handle Slide the sleeve into the enclosure and lift the sleeve handle to the top position to secure the sleeve in the enclosure NOTE To ensure optimal thermal performance do not replace the cover on the sleeve handle after the sleeve is installed in the enclosure Reinstall the cover only if the sleeve is not installed in the enclosure Installing A Quarter Height Blade In A Sleeve A CAUTION Install a blade blank in all empty blade slots to maintain proper thermal conditions Slide the blade into the sleeve and rotate the blade handle upward to secure the blade in the sleeve Figure 3 Installing a Quarter Height Blade Installing A Full Or Half Height Blade A CAUTION Install a blade blank in all empty blade slots to maintain proper thermal conditions Figure 4 Installing a
7. Dell PowerEdge M1000e M915 M910 M820 M710HD M710 M620 M610x M610 M520 and M420 Getting Started Guide anp f gulat beet del BMX01 ol HHB BA a gulatory Type DWHH H Ser s HHB Series FHB Series and QHB fios Notes Cautions and Warnings K NOTE A NOTE indicates important information that helps you make better use of your computer CAUTION A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem A WARNING A WARNING indicates a potential for property damage personal injury or death 2013 Dell Inc All Rights Reserved Trademarks used in this text Dell the Dell logo Dell Boomi Dell Precision OptiPlex Latitude PowerEdge PowerVault PowerConnect OpenManage EqualLogic Compellent KACE FlexAddress Force10 Venue and Vostro are trademarks of Dell Inc Intel Pentium Xeon Core and Celeron are registered trademarks of Intel Corporation in the U S and other countries AMD is a registered trademark and AMD Opteron AMD Phenom and AMD Sempron are trademarks of Advanced Micro Devices Inc Microsoft Windows Windows Server Internet Explorer MS DOS Windows Vista and Active Directory are either trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries Red Hat and Red Hat Enterprise Linux are registered trademarks of Red
8. Half Height Blade NOTE The above figure shows installation of a half height blade The procedure for installing a full height blade is identical to installing a half height blade Beginning at the top slide the blades into the enclosure from left to right When the blade is securely installed the blade handle returns to the closed position Connecting The CMC And iKVM Modules Figure 5 Connecting the CMC and iKVM Modules Connect the serial cable and network cable s from the management system to the CMC module If a second optional CMC module is installed connect it as well Connect the keyboard mouse and monitor to the optional iKVM module Connecting The System To Power Figure 6 Connecting Power to the System Connect the system power cables to the system power supplies A CAUTION Many repairs may only be done by a certified service technician You should only perform troubleshooting and simple repairs as authorized in your product documentation or as directed by the online or telephone service and support team Damage due to servicing that is not authorized by Dell is not covered by your warranty Read and follow the safety instructions that came with the product A CAUTION To prevent the power cables from being disconnected accidentally use the plastic clip on each power supply to secure the power cable to the power supply and use the strap to secure the power cable to the strain relief bar A CAUTION
9. MC This document is available online at dell com esmmanuals e The Integrated Dell Remote Access Controller iDRAC User s Guide provides information about installation configuration and maintenance of iDRAC on managed systems This document is available online at dell com esmmanuals e The rack documentation included with your rack solution describes how to install your system into a rack if required e Any media that ships with your system that provides documentation and tools for configuring and managing your system including those pertaining to the operating system system management software system updates and system components that you purchased with your system K NOTE Always check for updates on dell com support manuals and read the updates first because they often supersede information in other documents K NOTE When upgrading your system it is recommended that you download and install the latest BIOS drivers and systems management firmware on your system from dell com support Obtaining Technical Assistance If you do not understand a procedure in this guide or if the system does not perform as expected see your system Owner s Manual Dell offers comprehensive hardware training and certification See dell com training for more information This service may not be offered in all locations NOM Information The following information is provided on the device described in this document in compliance with the requireme
10. nts of the official Mexican standards NOM Importer Dell Inc de M xico S A de C V Paseo de la Reforma 2620 11 Piso Col Lomas Altas 11950 M xico D F Model number BMX01 Supply voltage 100 V CA to 240 V CA with 2700 W AC power supply units or 48 60 V CC with 2700 W DC power supply units 200 V CA to 240 V CA with 3000 W AC power supply units Frequency 50 Hz 60 Hz or N A Current consumption 16 A x6 or 75 A x6 Model number FHB Supply voltage 12 VCC Current consumption 75A Model number HHB Supply voltage 12V CC Current consumption 37A Model number QHB Supply voltage 12V CC Current consumption 35 A Technical Specifications K NOTE For additional specifications see your system Owner s Manual Power Blades Coin cell battery 3 V CR2032 Lithium coin cell Power Enclosure AC DC power supply per power supply module 2700 W Wattage 2700 W Connector IEC C20 Heat dissipation 1205 BTU hr maximum Maximum inrush current Under typical line conditions and over the entire system ambient operating range the inrush current may reach 55 A per power supply for 10 ms or less AC DC power supply per power supply module 3000 W Wattage 3000 W Connector IEC 320 Power Enclosure Heat dissipation 1200 BTU hr maximum NOTE Heat dissipation is calculated using the power supply wattage rating Maximum inrush current Under typical input voltage conditions and ove
11. r the entire system ambient operating range the inrush current may reach 55 A per power supply for 10 ms or less System Voltage Requirements 16 A 200 V AC to 240 V AC 50 Hz 60 Hz 3000 W power K NOTE This system is also designed to be connected to supply IT power systems with a phase to phase voltage not 16 A 100 V AC to 240 V AC 50 Hz 60 Hz 2700 W power exceeding 230 V supply DC DC power supply per power supply module Wattage 2700 W Connector Molex 394260002 at PSU end mating connector Molex 39422 0012 Heat dissipation 1205 BTU hr maximum Maximum inrush current Under typical input voltage conditions and over the entire system ambient operating range the inrush current may reach 120 A per power supply for 10 ms or less System Voltage Requirements 75 A 48 V DC to 60 V DC NOTE Heat dissipation is calculated using the power supply wattage rating Physical Blades PowerEdge M915 Height Width Depth Weight maximum PowerEdge M910 Height Width Depth Weight maximum PowerEdge M820 Height Width 38 5 cm 15 2 inch 5 cm 2 inch 48 6 cm 19 2 inch 12 7 kg 28 Ib 38 5 cm 15 2 inch 5 cm 2 inch 48 6 cm 19 2 inch 13 1 kg 29 Ib 38 5 cm 15 2 inch 5 cm 2 inch Physical Blades Depth Weight maximum PowerEdge M710 and M610x Height Width Depth Weight maximum PowerEdge M710HD and M620 Height Width Depth Weight maximum PowerEdge M610 Height
12. ssary for you to re mediate the environmental conditions that are causing the damage and or failures Re mediation of environmental conditions will be the responsibility of the customer Air Filtration Data center air filtration as defined by ISO Class 8 per pia a ae NOTE Applies to data center environments only S014641 witha I3 upper confidence limit Air filtration requirements do not apply to IT K NOTE Air entering the data center must have equipment designed to be used outside a data MERV11 or MERV13 filtration center in environments such as an office or factory floor Conductive Dust Air must be free of conductive dust zinc whiskers or other conductive particles NOTE Applies to data center and non data center p environments Corrosive Dust e Air must be free of corrosive dust NOTE Applies to data center and non data center e Residual dust present in the air must have a environments deliquescent point less than 60 relative humidity Gaseous Contamination K NOTE Maximum corrosive contaminant levels measured at lt 50 relative humidity Copper Coupon Corrosion Rate lt 300 month per Class G1 as defined by ANSI ISA71 04 1985 Silver Coupon Corrosion Rate lt 200 A month as defined by AHSRAE TC9 9 13
Download Pdf Manuals
Related Search