Dell Networking S5000 Installation Manual
Contents
1. T Technical Pe CIN G all ON Scenes rede AE 43 S Agency Eeler 45 USA Federal Communications Commission FCC Statement 45 Canadian Department of Communication Statement 45 European Union EMC Directive Conformance Statement 45 European Community Contact Japan VCCI Compliance for Class A Equipment Korean Certification of Complance ENEE Safety Standards and Compliance Agency Certftcatons EE 47 Electromagnetic Compatibility EM NENNEN 47 Product Recycling and Disposal EEN 48 9 Technical Support The iSupport Website Accessing ISUPPOFt d TEEN 49 Requesting a Hardware Replarcement EE 49 Contacting Technical Sup Portes 225 iccasicivc seis ceectves teed sat des aaea a Eaa aaa aaa aaa daan a a Aea aaaea AiR 50 About this Guide This guide provides site preparation recommendations and step by step procedures for rack mounting installing and replacing pluggable modules and connecting to a power source After you have completed the hardware installation and power up of the 5000 for software configuration information refer to the FTOS Configuration Guide for the 5000 Switch and for Command Line Interface CLI information refer to the FTOS Command Line Reference Guide for the S5000 Switch CAUTION To avoid electrostatic discharge ESD damage wear grounding wrist straps when handling this equipment AN WARNING Only trained and qualified personnel can install this equipment Read this guide before you install2. 1 Disconnect the power cable from the PSU 2 Use the grab handle to slide the PSU out of the switch PSU slot 3 Use the grab handle on the replacement PSU to slide it into the switch PSU slot 4 Attach the power cord to the replacement PSU Important Points to Remember for Installing a Fan Module e The Utility panel consists of four slots numbered from 0 to 3 Insert the fan modules in slots 1 and 2 e Ifa fan module fails the system continues to operate without a significant degradation in cooling capacity for a six hour duration e The cooling system is designed such that during normal operation the fans typically run at somewhere between 50 and 75 percent of their maximum speed at 26 C ambient temperature This feature results in lower noise and higher average fan life The switch increases the fan speed to maximum if the facility air condition fails or if a fan fails e The fan speed increases and decreases automatically based on the internal temperature The switch never intentionally turns off the fans e For proper ventilation position the 5000 in an equipment rack or cabinet with a minimum of 5 inches 12 7 cm of clearance around the exhaust vents When you install two 5000 systems near each other position the two chassis at least 5 inches 12 7 cm apart to permit proper airflow The acceptable ambient temperature ranges are listed in Technical Specifications e To view the log messages use the show logging com
3. equipment type SA Product Name Ethemet Switch EES Oo PPS Model model number So w Safety Standards and Compliance Agency Certifications CUS UL 60950 1 Second Edition CSA 60950 1 03 Second Edition EN 60950 1 Second Edition EN 60825 1 First Edition EN 60825 1 Safety of Laser Products Part 1 Equipment Classification Requirements and User s Guide EN 60825 2 Safety of Laser Products Part 2 Safety of Optical Fibre Communication Systems FDA Regulation 21CFR 1040 10 and 1040 11 IEC 60950 1 Second Edition including all National Deviations and Group Differences Electromagnetic Compatibility EMC Emissions International CISPR 22 2006 Class A Australia New Zealand AS NZS CISPR 22 2009 Class A Canada ICES 003 Issue 4 Class A Europe EN55022 2006 CISPR 22 2006 Class A Japan VCCI V 3 2011 04 Class A USA FCC CFR47 Part 15 Subpart B Class A Immunity EN 300 386 v1 5 1 2010 EMC for Network Equipment EN55022 2006 Class A EN 55024 1998 A1 2001 A2 2003 EN 61000 3 2 Harmonic Current Emissions EN 61000 3 3 Voltage Fluctuations and Flicker EN 61000 4 2 ESD EN 61000 4 3 Radiated Immunity 47 e EN 61000 4 4 EFT e EN 61000 4 5 Surge e EN 61000 4 6 Low Frequency Conducted Immunity Product Recycling and Disposal You must recycle or discard this system according to applicable local and national regulations Dell Networking encourages owners of information technology IT equip
4. Connect only to the power source specified on the unit When multiple electrical components are installed in a rack ensure that the total component power ratings do not exceed the circuit capabilities Overloaded power sources and extension cords present fire and shock hazards Elevated ambient temperature If installed in a closed rack assembly the operating temperature of the rack environment may be greater than the room ambient temperature Use care not to exceed the 40 C maximum ambient temperature of the switch Reduced air flow Install the equipment in the rack so that the amount of airflow required for safe operation of the equipment is not compromised Reverse air flow Necessary clearance is required to ensure cool air intake and to avoid hot air blow out from 1 0 panel Reliable earthing Maintain reliable earthing of rack mounted equipment Pay particular attention to the supply connections other than the direct connections to the branch circuit for example use of power strips Do not mount the equipment with the Utility panel facing in the downward position A WARNING These instructions are a condensed reference Read the safety instructions in your Safety Environmental and Regulatory information booklet before you begin K NOTE The illustrations in this document are not intended to represent a specific switch 23 Installing the 5000 Chassis into a 4 Post Rack or Cabinet K NOTE Dell Networking
5. data ports Stack Group 1 Stack Group 11 Stack Group 13 Stack Group 3 Stack Group 15 EE bra H Stack Group 2 Stack Group 14 Stack Group 12 Stack Group 0 Stack Group 10 Figure 23 Stack Group Assignments You can connect the systems while they are powered down or up Stacking ports are bidirectional The S5000 supports stacking in either a ring or a daisy chain topology To provide redundant connectivity Dell Networking recommends using the ring topology when stacking S5000 systems Ring Topology Daisy chain Topology 5000 1 5000 2 5000 2 5000 3 5000 3 Figure 24 Stacking Topology 39 Connecting Two S5000 Systems To provide backup connectivity and increased data transfer between the systems Dell Networking recommends inserting an additional cable between the two units in a second stacking port You can use any of the SFP or QSFP ports for stacking provided it is configured as a stacking port A CAUTION The 5000 does not require special stacking cables The cables used to connect 10GbE and 40GbE data ports are sufficient K NOTE The port numbers in the following procedure are examples only 1 Insert one end of the first cable into stack port 60 in chassis 1 bottom Insert the other end of the same cable into stack port 60 on chassis 2 top Insert a second cable into stack port 56 on chassis 2 top gt UN Insert the other end of the second cable into stack port 56 on c
6. supports only Ethernet modules modules 5 Four 40GbE OSFP ports each port ALSO supports 2 Slot 1 supports only Ethernet modules 4 x 10GbE mode 3 Slot 2 supports only Ethernet modules NOTE The LED displays for the system status are on both sides of the chassis The fan and power status LEDs are on the Utility panel 11 Utility Panel The Utility panel side of the platform contains the fan and power modules 1 2 3 4 TSP 5 Figure 3 5000 Power Supplies and Fan Modules 1 Slot 0 for PSU 0 4 Slot 3 for PSU 1 2 Slot 1 for Fan Module 0 5 Grab Handles 3 Slot 2 for Fan Module 1 Power Supplies The 5000 supports two hot swappable PSUs K NOTE The PSUs must be installed at the customer site The S5000 has SKUs that support the following configurations e AC PSU with fan airflow from UO to Utility e AC R PSU with fan airflow from Utility to 1 0 e DC PSU with fan airflow from UO to Utility e DC R PSU with fan airflow from Utility to 1 0 PSUs are field replaceable To ensure power redundancy and adequate cooling install two power supplies in the switch When running with full redundancy two PSUs installed and running you can remove and replace one PSU while the other PSU is running without disrupting traffic Fans The S5000 supports two fan trays with airflow directions from UO to Utility or Utility to 1 0 Do not mix 1 0 to Utility and Utility to UO airflows in a single S500
7. the lowest unused number with the current configuration Attaching a new unit may cause each unit in the stack to reload The subsequent configuration file in each unit includes the awareness of the new unit If you have a preconfigured unit that you want to add to the stack but you want to make sure that the configuration does not override the configuration of the stack add the unit while it is powered down to avoid stack management conflicts For more information about removing a unit from a stack and other stacking commands refer to the Stacking chapter in the FTOS Configuration Guide for the S5000 Switch and the Stacking Commands chapter in the F7OS Command Line Reference Guide for the S5000 Switch 42 Technical Specifications E NOTE Operate the product at an ambient temperature not higher than 40 C A CAUTION Lithium Battery Caution There is a danger of explosion if the battery is incorrectly replaced NOTE Replace the battery only with same or equivalent type Dispose of the batteries according to the manufacturer s instructions Table 5 Chassis Physical Design Parameter Height Width Depth Chassis weight with factory installed components Rack clearance required Table 6 Environmental Parameters Parameter Operating temperature Operating humidity Storage temperature Storage humidity Relative humidity Maximum thermal output Maximum Altitude Table 7 Power Requirements Parameter AC Power supply DC Power su
8. a faapai ikesh riina 22 Rack Mounting Safety Consideratons EEN 23 Installing the S5000 Chassis into a 4 Post Rack or Cabinet 24 Rack toppen eege Eden E 24 Important Points to Remember for Installing an Ethernet Module 24 Installing an Ethernet Module maarinde eeraa aara iida SOEN Eden 25 Replacing an Ethernet Module 26 Important Points to Remember for Installing a Fibre Channel Module AAA 26 Installing a Fibre Channel Module 27 Replacing a Fibre Chanmel Module 28 Important Points to Remember for Installing an AC Power Supphy EE 28 Installing an AC Power Supp 29 Important Points to Remember for Installing a DC Power Supp 30 Assembling and Connecting the Safety Ground Wire for DC Power Supp 31 Installing a DC Power SU pT Vaa A aAa AREAN aA SMAKA E RANG KARA EE 32 Installing the Ferrite Bead for DC Power and Return Cables ENEE 34 Securing Power Cables EEN Replacing an AC or DC Power Supply Important Points to Remember for Installing a Fan Module 36 Installing a Fan Moduler eeng a a a aaa aAa a Aa AN SAKEN RAR KLENA TR RA Rd Replacing a Fan Mod Oldie ie te Ree aaa aaa a eaaa eaaa reada Installing the SFP and QSFP Opttecs EEN Splitting QSFP Ports to SFP Porte Important Points to Hemember NEEN Connecting the Stacking Ports Optional Connecting Two S5000 Systemsa e aa dE ends en Eed et Connecting Three S5000 Systems ENEE Supplying Power and Powering Up the System 41 TEEN DC P TEEN Hot Swapping Units in a Stack
9. are labeled 0 to 47 The QSFP ports are labeled 48 and 56 for the lower ports and 52 and 60 for the upper ports E NOTE You can connect up to six 5000 switches in a single stack K NOTE The S5000 system does not stack with other S Series systems K NOTE Stacking is not supported on 40GbE ports operating in 4x10GbE quad mode K NOTE If you use three or more S5000 units in a stack you can connect up to a maximum of eight 10GbE ports or two 40GbE ports in links between peer switches If you use only two S5000 units in a stack you can connect up to four 40GbE ports in links between the two switches Important Points to Know e Data ports are configured as stacking ports in predefined stacking groups of 40GbE four 10GbE ports or one 40GbE port 38 e Stacking ports are divided into 16 stack groups 0 to 15 Each set of four 10GbE ports on an Ethernet module or each fixed 40GbE port on the front panel correspond to a stack group Each stack group has 40GbE of bandwidth When a stack group number is assigned the ports associated with that group are configured as stacking ports stack group 0 ports 0 3 stack group 1 ports 4 7 stack group 2 ports 8 11 and so on through stack group 11 ports 44 47 stack group 12 port 48 stack group 13 port 52 stack group 14 port 56 stack group 15 port 60 e Allthe ports in a stack group are placed in stacking mode You cannot use the unused ports in that group as
10. connecting DC power wires can permanently damage the power supply or the system Insert the copper ends into the mating connectors and tighten the captive screws at the top of the mating connector using a 2 Phillips screwdriver A WARNING To protect the power supply from electrostatic discharge you must cover the captive screws with the rubber cap before inserting the mating connector into the power supply Rotate the rubber cap clockwise to fix it over the captive screws Insert the mating connector into the power supply 33 7 Figure 19 Assembling the DC Input Power Wires 1 DC power socket 5 Wire 48V 2 Rubber cap 6 Wire RTN 3 Captive screws 2 7 Grounding Wire 4 DC power connector K NOTE The system is powered up as soon as the power cord is connected between the system and the power source A CAUTION Always disconnect the power cable before you service the power supply slots A CAUTION Use the power supply cord as the main disconnect device on the AC or DC system Ensure that the socket outlet is located installed near the equipment and is easily accessible Repeat steps 1 through 6 using the second PSU NOTE Ensure that the PSU is correctly installed When you correctly install the PSU the power connector is on the left side of the PSU Installing the Ferrite Bead for DC Power and Return Cables Add a ferrite bead to the DC power and return cables of the master module Install the bead with a si
11. it into the switch fan slot A CAUTION You must complete steps 1 and 2 within one minute or the system powers down Installing the SFP and OSFP Optics The 5000 has 48 small form factor pluggable plus SFP optical ports and four QSFP optical ports For a list of supported optics refer to the 5000 data sheet http www dell com us enterprise p force10 s series pd CAUTION ESD damage can occur if the components are mishandled Always wear an ESD preventive wrist or heel ground strap when handling the 5000 and its components WARNING When working with optical fibres follow all the warning labels and always wear eye protection Never look directly into the end of a terminated or unterminated fibre or connector as it may cause eye damage 1 Position the optic so it is in the correct position The optic has a key that prevents it from being inserted incorrectly 2 Insert the optic into the port until it gently snaps into place 37 K NOTE Both rows of QSFP ports require that you install the 40GbE optics with the tabs facing up NOTE When you cable the ports be sure not to interfere with the airflow from the small vent holes above and below the ports Splitting QSFP Ports to SFP Ports The S5000 supports splitting a single 40GbE QSFP port into four 10GbE SFP ports using one of the supported breakout cables For a list of supported optics refer to the S5000 data sheet http www dell com us enterprise p force10 s s
12. its affiliates Citrix Xen XenServer and XenMotion are either registered trademarks or trademarks of Citrix Systems Inc in the United States and or other countries VMware vMotion vCenter vCenter SRM and vSphere are registered trademarks or trademarks of VMware Inc in the United States or other countries IBM is a registered trademark of International Business Machines Corporation 2013 Rev AOX Contents 1 About this Guide eessen Related Publications 2 FODUCTON GE 7 Product Uespelt ele aaeeea aaa Od chidath a a a aaaea aaa aeia 7 3 Unpacking erte iere EE 9 Important Points Before You Continue 9 Hardware Installation Dvervieuw EE 10 4 Hardware OVEN IEW vis enee eet ee eer 11 V OMPane lisse tian carnegie gedeelt 11 Utility SITE 12 Power TEE 12 F ng SE EE sett wher ated che a a eld ia ee nh 12 Port Numbering Convention ENEE 13 ALELA A ARA AEEA TAEAE A lei REES EE 13 BEES HERE tee eelere 19 Site Elei SARA VVS E E RSS A RASAR ARENAN Cabinet PaCo O Ere sees aaa a a a n a aE aiaa a a aa aai den dere bn aa a aaa Storing Components later ii a AN Ran AR DON atte 21 Before You Bea eessen deed eege ede saat eeetciordesigcacstusedatachcn Aaaa a aaa iiaa 21 Install the S5000 Chassis in a Rack or Cabinet 22 To install the 5000 system Dell Networking recommends completing the installation procedures in the order presented here Attaching the Mounting Brackets a aa a a ap aa ra aaa ranean
13. lower part of the front of the module A WARNING Electrostatic discharge ESD damage can occur if components are mishandled Always wear an ESD preventive wrist or heel ground strap when handling the 5000 and its components K NOTE For the Ethernet module the part name and port number are inscribed on the handle as shown in the following figure K NOTE A blue color release latch indicates that the Ethernet module does not support hot swapping during switch operations Instead you must power down the switch before removing and replacing an Ethernet module A red color release latch indicates that the Ethernet module supports hot swapping during switch operations Figure 11 Part name and Port number on the Ethernet Module Handle 1 Part Name 2 Port Number Installing an Ethernet Module 1 Use the grab handle on the Ethernet module to slide it into the switch module slot 2 Connect any network interface cables to the attached module 25 Figure 12 Installing an Ethernet Module 1 Release latch 2 Ethernet Module Replacing an Ethernet Module K NOTE S5000 does not support the hot swapping of an Ethernet pluggable module during switch operations Instead you must power down the switch before removing and replacing an expansion module 1 Disconnect any network interface cables attached to the module 2 Use the grab handle to slide the Ethernet module out of the switch module slot 3 Use the grab handle o
14. outlet to the Utility panel connector Switch is rack mounted before you install the power supply modules Cabling is away from sources of electrical noise such as radios power lines and fluorescent lighting Make sure that the cabling is safely away from other devices that might damage the cables If needed allow one rack unit RU space between devices to provide room for cabling Airflow around the switch and through the vents is unrestricted Temperature around the unit does not exceed 104 F 40 C If the switch is in a closed or multirack assembly the temperature might be higher than normal room temperature Humidity around the switch does not exceed 85 percent Altitude at the installation site is below 6600 feet Switch is installed in an environment as free as possible from dust and foreign conductive material such as metal flakes from construction activities Cooling mechanisms such as fans and blowers in the switch can draw dust and other particles causing contaminant buildup inside the chassis which can result in system malfunction Install the 5000 Chassis in a Rack or Cabinet To install the 5000 system Dell Networking recommends completing the installation procedures in the order presented here NOTE Always handle the system and its components with care Avoid dropping the 5000 chassis or its field replaceable units NOTE For proper ventilation position the S5000 chassis in an equipment rack or cabinet wi
15. that does not exceed 85 percent noncondensing e In a dry clean well ventilated and temperature controlled room away from heat sources such as hot air vents or direct sunlight e Away from sources of severe electromagnetic noise e Positioned in a rack or cabinet or on a desktop with adequate space in the front rear and sides of the S5000 for proper ventilation and access Cabinet Placement Install the S5000 only in indoor cabinets designed for use in a controlled environment as described in Site Selection The cabinet must meet the following criteria e Minimum cabinet size and airflow are according to the Electronic Industries Alliance EIA standard 19 Storing Components If you do not install your S5000 and components immediately Dell Networking recommends properly storing the system and all optional components until you are ready to install them AN WARNING ESD damage can occur when components are mishandled Always wear an ESD preventive wrist or heel ground strap when handling the 5000 and its accessories After you remove the original packaging place the 5000 and its components on an anti static surface 1 Storage temperature must remain constant ranging from 4 to 158 F 20 C to 70 C Store on a dry surface or floor away from direct sunlight heat and air conditioning ducts Store in a dust free environment 20 Installation This document contains the following sections Before You Begi
16. 0 chassis All fans and PSUs in a configuration must be in the same airflow direction If you create a mixed airflow configuration the software notifies you of the invalid configuration The fans must be installed at the customer site Port Numbering Convention Even numbered ports are at the bottom of the I O panel and for modules odd numbered ports are at the top of the I O panel 1 5 9 13 17 21 25 29 33 37 41 45 52 60 3 7111 15 19 23 27 31 35 39 43 47 Peppers Ess Pa PPFPPFP e eme rare aaa wies Bed wa wa m hale ran E BE nse 21 6110 14 18 22 26 30 34 38 42 46 0 4 8 12 16 20 24 28 32 36 40 44 48 56 Figure 4 Port Numbering The previous figure shows the fixed four 40GbE data ports ports 48 52 56 and 60 and the four slots for pluggable modules on the S5000 UO panel You can also use the 40GbE ports in 4 x 10GbE mode The S5000 supports the following possible modules e 12 Port Ethernet Module 1G 10G speeds slot 0 1 2 or 3 e 12 Port Fibre Channel Module 2G 4G 8G speeds slot 0 The valid slot numbers are stack unit numbers from 0 to 11 The valid port numbers for each interface type are e 1GbE Ports 0 to 47 e 10GbE Ports 0 to 63 e 40GbE Ports 48 52 56 and 60 e Fibre Channel Ports 0 to 11 e Management Port 0 System Status You can view S5000 status information in several ways including LEDs and through the CLI show commands and with simple
17. 965 5800 e International 408 965 5800
18. C power connector Make sure that the power cord is secure As soon as the cable is connected between the S5000 and the power source the chassis is powered up there is no on off switch DC Power Connect the plug to each DC receptacle Make sure that the power cord is secure and the polarity is correct As soon as the cable is connected between the S5000 and the power source the chassis is powered up there is no on off switch Hot Swapping Units in a Stack You can add remove or swap 5000 units in an existing stack The units in the stack and the new units can be already powered up or powered down All units in a stack must run the same version of the operating system The order in which the units come online or are added to or removed from the stack affects how the stack identifies them and how the units identify themselves This order influences unit numbers management addresses and other elements of the configuration file Unit identification within the stack is determined by the identification algorithm you select The default algorithm has the units self identify as Unit 0 through Unit last based on the order in which they come online So when setting up a new set of switches in a stack you should have no trouble forcing the identification of the management unit and unit IDs by methodically supplying power to the units in your preferred sequence Similarly when you add a unit to the stack the unit is gracefully added as Unit last
19. Dell Networking 5000 Installation Guide Notes Cautions and Warnings K NOTE A NOTE indicates important information that helps you make better use of your computer CAUTION A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem AN WARNING A WARNING indicates a potential for property damage personal injury or death 2013 Dell Inc Trademarks used in this text Dell the Dell logo Dell Boomi Dell Precision OptiPlex Latitude PowerEdge PowerVault PowerConnect OpenManage EqualLogic Compellent KACE FlexAddress Force10 and Vostro are trademarks of Dell Inc Intel Pentium Xeon Core and Celeron are registered trademarks of Intel Corporation in the U S and other countries AMD is a registered trademark and AMD Opteron AMD Phenom and AMD Sempron are trademarks of Advanced Micro Devices Inc Microsoft Windows Windows Server Internet Explorer MS DOS Windows Vista and Active Directory are either trademarks or registered trademarks of Microsoft Corporation in the United States and or other countries Red Hat and Red Hat Enterprise Linux are registered trademarks of Red Hat Inc in the United States and or other countries Novell and SUSE are registered trademarks of Novell Inc in the United States and other countries Oracle is a registered trademark of Oracle Corporation and or
20. Dell Networking Tech Support Information to Submit When Opening a Support Case Managing Your Case Downloading Software Updates Technical Documentation Contact Information 50 Log in to iSupport at http www force10networks com CSPortal20 Main Login aspx and select the Service Request tab e Your name company name phone number and E mail address e Preferred method of contact e Model number e Software version number e Symptom description e Screen shots showing the symptom including any error messages This can include e Output fromthe show tech support command This report is very long so set the storage buffer in your terminal program to high e Output from the show logging command on the unit that experienced the failure This report is included as a section in the output of the show tech support command e Console captures showing the error messages e Console captures showing the troubleshooting steps taken e Saved messages to a syslog server if you use one Log in to iSupport and select the Service Requestt tab to view all open cases and Return Materials Authorizations RMAs Log in to iSupport and select the Software Center tab Log in to iSupport and select the Documents tab You can access this page without logging in using the Documentation link on the iSupport page E mail Dell Force10 Technical Support Dell com Web http support dell com Telephone e USA 1 866
21. European Standard EN 55022 The limits for Class A equipment were derived for commercial and industrial environments to provide reasonable protection against interference with licensed communication equipment WARNING This is a Class A product In a domestic environment this device may cause radio interference in which case you may be required to take adequate measures 45 European Community Contact Dell Networking EMEA Central Dahlienweg 19 66265 Heusweiler Germany http www force10networks com german Japan VCCI Compliance for Class A Equipment CORB HAULBREESRRRSEASEMHBRE VCC ORE SEA EREECHEN Ae TORE t RERA TEAT 5 CBR GEE5 FBMOTFCEMHEVUET I NRA ebzireicadezz SBLABRKENHSCEMHVET A WARNING Use the AC power cords with Dell Networking equipment only Do not use Dell Networking AC power cords with any unauthorized hardware This is Class A product based on the standard of the Voluntary Control Council For Interference by Information Technology Equipment VCCI If this equipment is used in a domestic environment radio disturbance may arise When such trouble occurs the user may be required to take corrective actions AS CAR EL TSE BRO KEY h Sage ESERI KEY ha duh Baas SOLD ACS AL PEC CEAMRECA BAA CSE n ERI KEY hE EAL thBmoOBRoO Key bEFBAL amp TFEL Korean Certification of Compliance YQ aS Sala ed pn ETS 0 BS Fl ae H 919 IAQ Hede HS grog SILC Korean Package Label 46
22. Phillips screwdrivers required e Screws for rack installation e Two to Four 1 0 Modules according to order e Two Blanks e One RJ 45 to DB 9 female cable e Two AC or DC power cords for AC or DC units country region specific e Getting Started Guide e Safety and Regulatory Information e Warranty and Support Information e Software License Agreement Place the container on a clean flat surface and cut all straps securing the container Open the container or remove the container top 1 2 3 Carefully remove all components from the container and place it on a secure and clean surface 4 Remove all packing material 5 Inspect the switch and accessories for damage Important Points Before You Continue e identify the I O and Utility panel on the chassis The 1 0 panel has four fixed 40GbE ports on the right side of the panel refer to Figure 1 The Utility panel has the power supply slots LEDs and USB slots on the left side of the panel refer to Figure 3 e Identify slots 0 1 2 and 3 on the I O panel refer to Figure 2 You can insert a Fibre Channel module only in slot 0 You can install the Ethernet modules in slots 0 1 2 and 3 e Identify slots 0 1 2 and 3 on the Utility panel refer to Figure 3 You can insert Power supply units PSUs only in slots 0 and 3 You can insert the Fan modules in any of the slots Figure 1 5000 1 0 and Utility Panels 1 1 0 panel 2 Utility panel 3 Four 40GbE QSFP ports eac
23. and power up this equipment This equipment contains two power cords Disconnect both power cords before servicing AN WARNING This equipment contains optical transceivers which comply with the limits of Class 1 laser radiation CLASS 1 LASER PRODUCT A WARNING When no cable is connected visible and invisible laser radiation may be emitted from the aperture of the optical transceiver ports Avoid exposure to laser radiation and do not stare into open apertures Related Publications For more information about the S5000 refer to the following documents e FTOS Configuration Guide for the S5000 Switch es FTOS Command Line Reference Guide for the S5000 Switch es FTOS Release Notes for the S5000 Switch NOTE For the most recent documentation and software visit iSupport registration for access to some sections is required http www dell com support manuals Introduction This document provides basic information about installing the S5000 switch For information about how to configure and monitor switch features refer to the F70S Configuration Guide for the S5000 Switch which is available on the Dell Support website at http support dell com manuals This document contains the following sections e Product Description e Unpacking the Switch e Hardware Overview e Site Preparations e Installation e Technical Specifications e Agency Compliance e Technical Support Product Description The 5000 is pa
24. ces click the LOGIN link and enter your userid and password Requesting a Hardware Replacement 1 Determine the part number and serial number of the component To list the numbers for all components installed in the chassis use the show inventory command 2 Request a RMA number from Tech Support by opening a support case Open a support case by a Using the Create Service Request form on the iSupport page refer to Contacting Technical Support b Contacting Dell Networking directly by E mail or by phone refer to Contacting Technical Support Provide the following information when using E mail or phone Part number description and serial number of the component Your name organization name telephone number fax number and E mail address Shipping address for the replacement component including a contact name phone number and E mail address A description of the failure including log messages This can include e Output fromthe show tech support command This report is very long so set the storage buffer in your terminal program to high e Output fromthe show logging command on the unit that experienced the failure This report is included as a section in the output of show tech support command 49 e Console captures showing the error messages e Console captures showing the troubleshooting steps taken e Saved messages to a syslog server if you use one Contacting Technical Support How to Contact
25. e wrist or heel ground strap when handling the 5000 and its components K NOTE The part name and port number of a Fibre Channel module are inscribed on the handle as shown below Figure 13 Part name and Port number on the Fibre Channel Module Handle 1 Part Name 2 Port Number Installing a Fibre Channel Module 1 Use the grab handle on the Fibre Channel module to slide it into the switch module slot 2 Connect any network interface cables to the attached module 27 Figure 14 Installing a Fibre Channel Module 1 Release latch 2 Fibre Channel Module Replacing a Fibre Channel Module 1 2 3 4 NOTE S5000 does not support the hot swapping of a Fibre Channel pluggable module during switch operations Instead you must power down the switch before removing and replacing an expansion module Disconnect any network interface cables attached to the module Use the grab handle to slide the Fibre Channel module out of the switch module slot Use the grab handle on the replacement Fibre Channel module to slide it into the switch module slot Connect any network interface cables to the attached module Important Points to Remember for Installing an AC Power Supply The PSU slides into the slot smoothly Do not force a PSU into a slot as this action may damage the PSU or the 5000 chassis The S5000 supports AC and DC power supplies with two air flow directions I O to Utility and Utility to 1 0 The 5000 does not supp
26. er LED Green blinking mode OR Switch in Standalone mode Off e Switch in Stacking Standby mode e Switch in Stacking Member mode PSU status LED e Green solid e Normal operation e Off e Power not present Fan status LED e Green solid e Normal operation e Off e Power not present Figure 7 Module LEDs 1 Port locator beacon LED 2 Port link activity LED 3 Module locator beacon LED 4 Module status LED K NOTE The downward and upward pointing triangles denote the lower and upper port LEDs respectively Table 2 Ethernet Port Module LEDs Label LED Color Display Description Port locator beacon LED off e No activity 15 Label Port link activity LED Module locator beacon LED Module status LED Table 3 Fibre Channel Port Module LEDs Label Port locator beacon LED Port link activity LED Module locator beacon LED Module status LED LED Color Display Blue Off Green solid Green blinking Off Blue Off Green solid Yellow LED Color Display Off Blue Green Off Green solid Green blinking Off Green Off Green solid Yellow Description Port beacon locator No link or interface disabled Link present and interface enabled Ethernet module Port has activity No activity Module beacon locator Module is not powered up Module is powered up Problem detected with module Description No activity Port beacon locator Fibre Channel mode enabled No link or inter
27. eries pd e Configure the system to recognize the port mode change CONFIGURATION mode stack unit unit number port number portmode quad stack unit lt unit number gt Enter the stack member unit identifier of the stack member to reset The range is 0 to 11 The default is 0 port lt number gt Enter the port number of the 40GbE port to be split The range is 48 to 60 portmode quad Configure a 40GbE port to operate in 4x10GbE mode Example of splitting a QSFP port to SFP ports stack unit 0 port 52 portmode quad Important Points to Remember e You cannot use split ports as a stack link to stack an 5000 unit e The quad port must be in a default configuration before you can split it into four 10GbE SFP ports When you split the port the 40GbE port is lost in the running configuration Be sure that the port is also removed from other L2 L3 feature configurations e For the split port change to take effect you must reload the system after issuing the CLI change commands Connecting the Stacking Ports Optional Before you make your stacking port connections rack mount the systems or insert them into a cabinet To connect the stacking ports insert one end of the optical cable into a configured port and insert the other end of the optical cable into a similarly configured port of the adjacent system There are no unique stacking ports you can configure the SFP and QSFP ports to act as stacking ports The SFP ports
28. face disabled Link present and interface enabled Port has activity No activity Module beacon locator Module is not powered up Module is powered up Problem detected with module Figure 8 QSFP Port LEDs 1 Port link activity LED Table 4 40GbE Port Module LEDs Label LED Color Display Port link activity LED e off e Green solid e Green blinking Description e No link or interface disabled e Link present and interface enabled e Port has activity 17 Site Preparations The 5000 is suitable for installation as part of a Common Bond Network CBN It can be installed in e network telecommunication facilities e data centers e other locations where the National Electric Code NEC applies This chapter contains the following sections e Site Selection e Cabinet Placement e Storing Components Site Selection Dell Networking equipment is intended for installation in restricted access areas A restricted access area can only be accessed by service personnel by using a special tool lock key or other means of security and access is controlled by the authority responsible for the location Ensure that the area where you install your S5000 system meets the following safety requirements e Near an adequate power source Connect the system to the appropriate branch circuit protection as defined by your local electrical codes e Environmental temperature between 32 to 104 F 0 to 40 C e Relative humidity
29. fans must have the same color strap If you mismatch the airflows the following error message appears and the system shuts down 00 02 19 S5000 0 CHMGR 2 PSU_TYPE_ AIRFLOW MISMATCH Mismatching PSU airflow detected Unit 0 shall get shutdown in next 60 seconds if mismatch not rectified 00 02 19 STKUNITO M CP CHMGR 1 PSU_AIRFLOW_COMBO MISMATCH Major alarm Mismatching PSU airflow detected in unit 0 Installing an AC Power Supply 3 Remove the PSU from the electro static bag Use the grab handle to slide the PSU into the switch PSU slot install the PSU exposed PCB edge connector first The PSU slot is keyed so that the PSU can be fully inserted in only one way When you install the PSU correctly it snaps into place and is flush with the back of the switch Figure 15 Installing an AC Power Supply 1 Slot 0 for AC PSU 0 2 Release latch Plug in the AC3 prong cord from the switch PSU to the external power source the AC wall outlet 29 4 Figure 16 Connecting AC Power Supply Cords 1 AC3 Prong NOTE The system is powered up as soon as you connect the power cord between the system and the power source A CAUTION Always disconnect the power cable before you service the power supply slots A CAUTION Use the power supply cord as the main disconnect device on the AC system Ensure that the socket outlet is located installed near the equipment and is easily accessible Repeat steps 1 through 3 above us
30. h port ALSO supports 4 x 10GbE mode Hardware Installation Overview To install the 5000 follow these steps Attach the mounting brackets Install the S5000 chassis into a 4 post rack or cabinet Ground the rack Install the Ethernet and or Fibre Channel modules Fibre Channel module must be installed only in slot 0 Install the power supplies Secure the power cables Install the fan modules Install the SFP and QSFP optics Supply power and power up the system oon ea P Sa N gt Hardware Overview This section contains information about device characteristics and modular hardware configurations for the S5000 The 5000 has the following physical dimensions e Height 1 71 inches 43 5 mm e Width 17 4 inches 441 9 mm e Depth 28 inches 711 2 mm The 5000 has a chassis design with 640Gbps switching bandwidth The system also provides one DB9 RS 232 console port with YOST RJ 45 pinout and a dedicated Ethernet service port for out of band 00B management functions 1 0 Panel All fixed data ports 4 x 40GbE quad small form factor pluggable plus OSFP ports and the four slots for pluggable modules are on the I O panel The 1 0 panel includes e Pluggable Modules 12 Port Ethernet Module 1G 10G speeds 12 Port Fibre Channel Module 2G 4G 8G speeds e 4x 40GbE QSFP Ports and light emitting diodes LEDs Figure 2 5000 1 0 Panel 1 Slot 0 supports Ethernet and Fibre Channel 4 Slot 3
31. hassis 1 bottom 5000 2 a mn gn gn gn KA ate ale 5000 1 bh hh Kb ate ale Figure 25 Two 5000 Systems Connected in a Ring Connecting Three 5000 Systems To provide backup connectivity and increased data transfer between the systems Dell Networking recommends inserting an additional cable between the two units in a second stacking port A CAUTION The S5000 does not require special stacking cables The cables used to connect 10GbE and 40GbE data ports are sufficient K NOTE The port numbers in the following procedure are used as examples only 1 Insert one end of the first cable into stack port 60 of chassis 1 bottom 2 Insert the other end of the cable into stack port 56 of chassis 2 center 40 3 Insert the second cable into stack port 60 of chassis 2 center and port 56 of chassis 3 top 4 Use the third cable to connect the top and bottom units by inserting one end of the cable into stack port 56 on chassis 1 bottom and the other end of the cable into stack port 60 on chassis 3 top 5000 3 a gn is gy gin db EA 5000 2 a nihi ahi gn gin hochas 5000 1 a nhi ahi ahi g s d KEE Figure 26 Three S5000s Connected in a Ring Supplying Power and Powering Up the System Supply power to the S5000 system after the chassis is mounted in a rack or cabinet WARNING Installing and swapping of Fibre Channel or Ethernet modules must be done BEFORE power up If you need to rep
32. imits Dell Networking is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications in the equipment Unauthorized changes or modification could void the user s authority to operate the equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions e This device may not cause harmful interference e This device must accept any interference received including interference that may cause undesired operation Canadian Department of Communication Statement Industry Canada Class A emission compliance statement This Class A digital apparatus complies with Canadian ICES 003 Avis de conformit la r glementation d Industrie Canada Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada European Union EMC Directive Conformance Statement This product is in conformity with the protection requirements of EU Council Directive 2004 108 EC on the approximation of the laws of the Member States relating to electromagnetic compatibility Dell Networking cannot accept responsibility for any failure to satisfy the protection requirements resulting from a nonrecommended modification of this product including the fitting of non Dell option cards This product has been tested and found to comply with the limits for Class A Information Technology Equipment according to CISPR 22
33. ing the second PSU NOTE Ensure that the PSU is correctly installed When you correctly install the PSU the power connector is on the left side of the PSU Important Points to Remember for Installing a DC Power Supply 30 When using DC power supply peel off the DC electrical label and place it on the main regulatory label found on the bottom of the S5000 chassis Position this label over the AC electrical ratings within the dashed outline The PSU slides into the slot smoothly Do not force a PSU into a slot as this action may damage the PSU or the S5000 chassis The S5000 supports AC and DC power supplies with two air flow directions I O to Utility and Utility to 1 0 The S5000 does not support mixing PSU types that is you cannot replace an AC PSU with a DC PSU and an AC R PSU with a DC R PSU The fan airflow direction for both the PSUs must be the same For DC PSUs the power status LED is on the upper left corner A DC PSU must be properly grounded The system does not work when plugged into the wrong power source polarity To view the log messages use the show logging command For more information refer to the System Logs chapters of the FTOS Command Line Reference Guide for the S5000 Switch and FTOS Configuration Guide for the S5000 Switch A A A A WARNING Although the switch can run on one PSU Dell Networking highly recommends using two PSUs for full redundancy and proper cooling If the switch needs to run with o
34. lace a module power down the system before you replace it If you replace a module when the system is powered up the system does not recognize the module Online insertion of modules can result in a catastrophic failure Dell Networking recommends reinspecting your system prior to powering up Verify that e The equipment is properly secured to the rack e The equipment rack is properly mounted and grounded e The ambient temperature around the unit which may be higher than the room temperature is within the limits specified for the S5000 e There is sufficient airflow around the chassis e The input circuits are correctly sized for the loads and that you use sufficient overcurrent protection devices K NOTE For powering up an AC PSU an AC power cable is included in the shipping container You must order all other power cables separately A CAUTION ESD damage can occur if the components are mishandled Always wear an ESD preventive wrist or heel ground strap when handling the S5000 and its components 41 When the system powers up the fans come on at high speed The fan speed slows as the system boots up The power status LED blinks until the boot up sequence is complete When the boot up is complete the power status LED is steadily lit AC Power CAUTION Ensure that the PSU is installed correctly The AC power connector must be on the left side of the PSU and the status LED at the top of the PSU Connect the plug to each A
35. mand For more information refer to the System Logs chapters of the FTOS Command Line Reference Guide for the S5000 Switch and FTOS Configuration Guide for the S5000 Switch A CAUTION DO NOT mix airflow directions The airflow directions are color coded A red label indicates that hot air is expelled from the PSU and a blue label indicates that hot air is expelled from the 1 0 Both fans must use the same airflow direction UO to Utility or Utility to 1 0 The power supplies and fans must have the same color strap If you mismatch the airflows the following error message appears and the system shuts down 00 00 53 S5000 3 CHMGR 2 PSU_TYPE_ AIRFLOW _ MISMATCH Mismatching PSU and FAN airflow detected Unit 0 shall get shutdown in next 60 seconds if mismatch not rectified 00 00 53 STKUNIT3 M CP CHMGR 1 PSU_AIRFLOW_COMBO MISMATCH Major alarm Mismatching PSU and FAN airflow detected in unit 0 The fan modules are field replaceable Module slot 1 is on the left side of the chassis module slot 2 is on the right side of the chassis 36 Installing a Fan Module 1 Take the fan module out of the shipping box 2 Use the grab handle to slide the fan module into the switch fan slot as shown below Figure 22 Installing a Fan Module 1 Fan module 0 Slot 1 2 Release latch Replacing a Fan Module 1 Use the grab handle to slide the fan module out of the switch fan slot 2 Use the grab handle on the replacement module to slide
36. ment to responsibly recycle their equipment when it is no longer needed Dell Networking offers various product return programs and services in several countries to assist equipment owners in recycling their IT products Waste Electrical and Electronic Equipment WEEE Directive for Recovery Recycle and Reuse of IT and Telecommunications Products Dell Networking switches are labeled in accordance with European Directive 2002 96 EC concerning waste electrical and electronic equipment WEEE The Directive determines the framework for the return and recycling of used appliances as applicable throughout the European Union This label is applied to various products to indicate that the product is not to be thrown away but rather reclaimed upon end of life per this Directive Figure 27 The European WEEE symbol In accordance with the European WEEE Directive electrical and electronic equipment EEE is to be collected separately and to be reused recycled or recovered at end of life Users of EEE with the WEEE marking per Annex IV of the WEEE Directive as shown above must not dispose of end of life EEE as unsorted municipal waste but use the collection framework available to customers for the return Specifications 47 recycling and recovery of WEEE Customer participation is important to minimize any potential effects of EEE on the environment and human health due to the potential presence of hazardous substances in EEE Dell Networking products
37. n Install the 5000 Chassis in a Rack or Cabinet Attaching the Mounting Brackets Rack Mounting Safety Considerations Installing the 5000 Chassis into a 4 post rack or cabinet Rack Grounding Important Points to Remember for Installing an Ethernet Module Installing an Ethernet Module Replacing an Ethernet Module Important Points to Remember for Installing a Fan Module Installing a Fibre Channel Module Replacing a Fibre Channel Module Important Points to Remember for Installing an AC Power Supply Installing an AC Power Supply Important Points to Remember for Installing a DC Power Supply Assembling and Connecting the Safety Ground Wire for DC Power Supply Installing a DC Power Supply Installing the Ferrite Bead for DC Power and Return Cables Securing The Power Cable s Replacing an AC or DC Power Supply Important Points to Remember for Installing a Fan Module Installing a Fan Module Replacing a Fan Module Installing the SFP and QSFP Optics Splitting QSFP Ports to SFP Ports Connecting the Stacking Ports Optional Connecting Two 5000 Systems Connecting Three S5000 Systems Supplying Power and Powering Up the System Hot Swapping Units in a Stack Tips Before You Begin Before installing the switch verify that you meet these guidelines 21 Enough clearance to the front of the switch so you can read the LEDs AC DC power cord reaches from the power
38. n the replacement Ethernet module to slide it into the switch module slot 4 Connect any network interface cables to the attached module Important Points to Remember for Installing a Fibre Channel Module e You must insert the Fibre Channel module only in slot 0 e Installing and swapping of Fibre Channel modules must be done BEFORE power up If you need to install or replace a module power down the system before you install or replace it If you install or replace a module when the system is powered up the system does not recognize the module Online insertion of modules can result in a catastrophic failure e The 5000 does not support the hot swapping of a Fibre Channel pluggable module during switch operations Instead you must power down the switch before removing and replacing a Fibre Channel module e Although the handle and port numbering may appear differently on a Fibre Channel module there is no functional difference A module may have A larger handle that covers the entire front of the module and has the part number written on top of the handle Port numbering is written on the front of the handle A smaller handle that is half the size and does not cover the release button The part number is written on the front of the handle Port numbering is written on the lower part of the front of the module 26 WARNING Electrostatic discharge ESD damage can occur if components are mishandled Always wear an ESD preventiv
39. network management protocol SNMP For more information about these options refer to the F70S Command Line Reference Guide and FTOS Configuration Guide for the 5000 Switch As shown in the following figure the S5000 includes LED displays on the 1 0 and Utility side of the chassis When the 5000 powers up or reloads the status LED on the power supplies are solid green The following table lists the LED definitions for the S5000 system 13 i e oc 7 Figure 5 System LEDs Utility Panel AC Power Supplies installed 1 Locator beacon LED 5 Seven segment display to identify Stack ID 2 Alarm LED 6 PSU status LED 3 System status LED 7 Fan status LED 4 Master LED K NOTE For AC PSUs an illuminated translucent handle indicates the power status K NOTE For DC PSUs the power status LED is on the upper left corner 3 2 Figure 6 System LEDs I O Panel 1 Locator beacon LED 2 Alarm LED 3 System status LED Table 1 System LED Displays Utility and UO Panel Label LED Color Display Description Locator beacon LED e Off No activity e Blue e System beacon locator Alarm LED es Off e No alarm e Amber solid e Minor alarm e Red solid e Critical alarm System status LED e Off No power e Green solid e Normal operation Label LED Color Display Description e Green blinking e System is booting e Amber solid e System in card problem state m 2 e Green solid e Switch in Stacking Master Mast
40. ng to DC power or installing grounds yourself All electrical wiring must comply with applicable local or national codes and practices Damage due to servicing that Dell Networking did not authorize is not covered by your warranty Strip the insulation from the end of the green yellow wire exposing approximately 4 5 mm 0 175 inch of copper wire Using a hand crimping tool Tyco Electronics 58433 3 or equivalent crimp the ring tongue terminal Jeeson Terminals Inc R5 4SA or equivalent to the green yellow wire safety ground wire Connect the safety ground wire to the grounding post on the back of the system using a 6 32 nut equipped with a locking washer 31 Figure 17 Assembling and Connecting the Safety Ground Wire For DC Power Supply 1 Safety ground wire 4 Spring washer 2 Grounding post 5 6 32 nut 3 Locking washer Installing a DC Power Supply 1 Remove the PSU from the electro static bag 2 Use the grab handle to slide the PSU into the switch PSU slot install the PSU exposed PCB edge connector first The PSU slot is keyed so that the PSU can be fully inserted in only one way When you correctly install the PSU it snaps into place and is flush with the back of the switch 32 Figure 18 Installing a DC Power Supply 1 Slot 0 for DC PSU 0 2 Release latch Strip the insulation from the ends of the DC power wires exposing approximately 13 mm 0 5 inch of copper wire WARNING Reversing polarity when
41. ngle loop 1 2 34 Open ferrite bead with the depressions facing up Wrap the DC power and return cables around the ferrite bead twice if two turns of the cable fit inside the ferrite otherwise simply clamp the ferrite onto both cables 3 4 Figure 20 Installing the Ferrite Bead for DC Power and Return Cables 1 Ferrite Bead 2 DC Power and Return Cables Leave approximately 4 to 5 inches of the DC power and return cables end protruding from the ferrite Snap the ferrite bead shut Securing Power Cables 1 2 Bend the system power cables as shown in the following illustration and attach to the cable clasp Figure 21 Securing Power Cables Plug the other end of the power cables into a grounded electrical outlet or a separate power source such as an uninterruptible power supply UPS or a power distribution unit PDU 35 NOTE For better performance ensure that the system is connected to a stand alone power source with stable power supply Replacing an AC or DC Power Supply To replace an AC or DC power supply follow these steps K NOTE Although the switch can run on one PSU Dell Networking highly recommends using two PSUs for full redundancy If the switch needs to run with only one PSU for a time be sure to cover the second PSU slot opening with a blank plate to avoid overheating K NOTE If a PSU fails you must completely replace it There are no field serviceable components in the PSU
42. nly one PSU for a time be sure to cover the second PSU slot opening with a blank plate to avoid overheating WARNING The Utility panel consists of four slots numbered from 0 to 3 Insert PSUs in slots 0 and 3 WARNING The PCB edge connector is at the bottom of the switch Avoid installing the switch upside down WARNING Electrostatic discharge ESD damage can occur if components are mishandled Always wear an ESD preventive wrist or heel ground strap when handling the S5000 and its components CAUTION DO NOT mix airflow directions The airflow directions are color coded A red label indicates that hot air is expelled from the PSU and a blue label indicates that hot air is expelled from the 1 0 Both fans must use the same airflow direction I O to Utility or Utility to 1 0 The power supplies and fans must have the same color strap If you mismatch the airflows the following error message appears and the system shuts down 00 02 19 S5000 0 CHMGR 2 PSU_TYPE AIRFLOW MISMATCH Mismatching PSU airflow detected Unit 0 shall get shutdown in next 60 seconds if mismatch not rectified 00 02 19 STKUNITO M CP CHMGR 1 PSU_AIRFLOW_COMBO MISMATCH Major alarm Mismatching PSU airflow detected in unit 0 Assembling and Connecting the Safety Ground Wire for DC Power Supply AN WARNING For equipment using 48 60 V DC power supplies a qualified electrician must perform all connections to DC power and to safety grounds Do not attempt connecti
43. ort mixing PSU types that is you cannot replace an AC PSU with a DC PSU and an AC H PSU with a DC R PSU The fan airflow direction for both the PSUs must be the same For AC PSUs an illuminated translucent handle indicates the power status To view the log messages use the show logging command For more information refer to the System Logs chapters of the F70S Command Line Reference Guide for the S5000 Switch and FTOS Configuration Guide for the S5000 Switch WARNING Although the switch can run on one PSU Dell Networking highly recommends using two PSUs for full redundancy and proper cooling If the switch needs to run with only one PSU for a time be sure to cover the second PSU slot opening with a blank plate to avoid overheating A WARNING The Utility panel consists of four slots numbered from 0 to 3 Insert PSUs in slots 0 and 3 28 A A A WARNING The PCB edge connector is at the bottom Avoid installing the switch upside down WARNING Electrostatic discharge ESD damage can occur if components are mishandled Always wear an ESD preventive wrist or heel ground strap when handling the 5000 and its components CAUTION DO NOT mix airflow directions The airflow directions are color coded A red label indicates that hot air is expelled from the PSU and a blue label indicates that hot air is expelled from the 1 0 Both power supplies must use the same airflow direction 1 0 to Utility or Utility to 1 0 The power supplies and
44. pply Maximum current draw per system Maximum power consumption Specifications 1 71 inches 43 5 mm 17 4 inches 441 mm 28 inches 711 mm 34 pounds approx 15 42 kg es Front 5 inches 12 7 cm e Rear 5 inches 12 7 cm Specifications 32 to 104 F 0 to 40 C 10 to 85 percent RH noncondensing 40 to 158 F 40 to 70 C 5 to 95 percent RH noncondensing 10 to 85 percent noncondensing 2388 BTU hr No performance degradation to 6600 ft Specifications 100 VAC 240 VAC 50 60 Hz 48V 60V VDC 7A 100 VAC 3 5 A 200 VAC 700 Watts 43 44 Agency Compliance USA Federal Communications Commission FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device under Part 15 of the FCC rules These limits are designated to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy If it is not installed and used in accordance to the instructions it may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to take whatever measures necessary to correct the interference at their own expense Properly shielded and grounded cables and connectors must be used in order to meet FCC emission l
45. recommends that one person hold the S5000 chassis in place while a second person attaches the brackets to the posts Attach the bracket ears to the rack or cabinet posts using two screws for each bracket Ensure the screws are tightened firmly Figure 10 Front Rack Installation 1 Screws 2 4 Post Rack or Cabinet 3 Mounting Bracket Rack Grounding When you prepare your equipment rack ensure that the rack is earth ground You must ground the equipment rack to the same ground point the power service uses in your area The ground path must be permanent Important Points to Remember for Installing an Ethernet Module Installing and swapping of Ethernet modules must be done BEFORE power up If you need to install or replace a module power down the system before you install or replace it If you install or replace a module when the system is powered up the system does not recognize the module Online insertion of modules can result in a catastrophic failure e Although the handle and port numbering may appear differently on an Ethernet module there is no functional difference A module may have A larger handle that covers the entire front of the module and has the part number written on top of the handle Port numbering is written on the front of the handle 24 A smaller handle that is half the size and does not cover the release button The part number is written on the front of the handle Port numbering is written on the
46. rt of Dell Networking s S Series switches for Data Center Top of Rack ToR switches The 5000 is purpose built to provide architectural flexibility for unified and virtualized environments It is a 10G ToR solution that enables converged local area networks LAN and storage area networks SAN in the same box The S5000 delivers Fibre Channel over Ethernet FCoE and Fibre Channel FC capability in a one rack unit RU ToR switch form factor The S5000 supports Data Center Bridging ETS PFC DCBX FCoE Transit FIP Snooping NPIV Proxy Gateway NPG and Internet small computer system interface iSCSI storage traffic The S5000 also provides aggregation and convergence functionality using pluggable modules for flexible configuration 3 Unpacking the Switch The 5000 and its accessories are shipped in multiple boxes Before unpacking the switch inspect the container and immediately report any evidence of damage Verify that you have received your ordered items For example if you order one 5000 switch the following items are included WARNING If any item is missing or damaged contact your Dell Networking representative or reseller for instructions AN WARNING Electrostatic discharge ESD damage can occur if components are mishandled Always wear an ESD preventive wrist or heel ground strap when handling the 5000 and its components e One S5000 switch e Two Fans e Two Power Supplies either AC or DC e Onerail kit 1 and 2
47. th a minimum of 5 inches 12 7 cm of clearance around exhaust vents The acceptable ambient temperature ranges are listed in the Environmental Parameters section A CAUTION Always wear an ESD preventive wrist or heel ground strap when handling the S5000 and its components As with all electrical devices of this type take all necessary safety precautions to prevent injury when installing this system ESD damage can occur if components are mishandled Attaching the Mounting Brackets The 5000 is shipped with mounting brackets rack ears and the required screws eight screws for rack or cabinet installation The brackets are enclosed in a package with the chassis 1 2 22 Take the brackets and screws out of their packaging Slide the mounting brackets as shown in the following figure Figure 9 Slide the mounting brackets 1 Utility side of the chassis 2 Mounting Bracket 3 Holding Bracket factory installed Rack Mounting Safety Considerations You may either place the switch on the rack shelf or mount the switch directly into a 19 wide EIA 310 E compliant rack Rack loading Overloading or uneven loading of racks may result in shelf or rack failure which may damage equipment and cause possible personal injury Stabilize racks in a permanent location before loading begins Mount the components beginning at the bottom of the rack then work to the top Do not exceed your rack load rating Power considerations
48. which fall within the scope of the WEEE are labeled with the crossed out wheelie bin symbol as shown above as required by WEEE For information on Dell Networking product recycling offerings see the WEEE Recycling instructions on iSupport at http downloads dell com Manuals all products esuprt_electronics esuprt_docking_stations dell superspeed usb3 dock stn_Reference 20Guide_en us pdf c us amp l en amp cs amp s gen 48 Technical Support This chapter contains the following sections e The iSupport Website e Accessing iSupport Services e Requesting a Hardware Replacement e Contacting Technical Support The iSupport Website iSupport provides a range of documents and tools to assist you with effectively using Dell Networking equipment and mitigating the impact of network outages Through iSupport you can obtain technical information regarding Dell Networking products access to software upgrades and patches and open and manage your Tech Support cases Dell Networking iSupport provides integrated secure access to these services Accessing iSupport Services The URL for iSupport is http www force10networks com CSPortal20 Main Login aspx You must have a userid and password to access iSupport services 1 On the Dell Networking Support page click the Account Request link 2 Fill out the User Account Request form and click Send You will receive your userid and password by E mail 3 To access iSupport servi
Download Pdf Manuals
Related Search