DCS none User's Manual
Contents
1. The Contact page displays dCS web site URL email address telephone and fax VIVI numbers If you have any difficulty please contact your dealer for help first The Clock Information page reports the status of the unit Output frequency kHz Temperature stable unstable Coupling TTL Bipolar Master Slave mode Dither on off Input frequency kHz MHz unlocked Temperature C Use the buttons to scroll down the list and the MENU button to exit The CD Update feature allows you to load new software into your system from either a Update Scarlatti transport or any STANDARD CD player or transport Note that some non Red Book CD transports change the digital data and cannot be used to download new software Please follow the instructions supplied with the update CD carefully CLOCK SETTINGS Menu ay The Coupling menu page sets the External Input to accept either an AC coupled Bipolar reference generated by a GPS receiver for example or a Word Clock at TTL levels The Factory Reset menu page resets the unit to standard settings These are nE 4 Output Frequency to 44 1kHz Display to On H Hi Dither to Off Brightness to maximum Coupling to TTL Contrast to 60 DISPLAY SETTINGS Menu Set the display Brightness to a comfortable level Set the display Contrast to a comfortable level Runs a Display Test routine which flashes all the indicators and the main display Filename Scarlatti Clock2. Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x SPECIFICATION Clock type Clock Frequencies Clock Accuracy Word Clock Outputs Reference Input Start up time Size and weight Power requirements June 2008 Class 1 Master Clock with dual VCXO temperature compensated 44 1kHz or 48kHz Better than 1ppom when shipped guaranteed for 12 months from shipping typically 0 1ppm when shipped and stabilised 8 independently buffered outputs on 75Q BNC connectors all carry the same clock frequency External Reference Input on 1x 750 BNC connector Accepts word clock with the Coupling menu page set to TTL or AC coupled signals with the Coupling menu page set to Bipolar at 32kHz 44 1kHz 48kHz 88 2kHz 96kHz 1MHz 5MHz or 10MHz Lock range is 300ppm Typically 1 minute to rated accuracy 460mm 18 0 long x 405mm 15 9 deep x 73mm 2 9 high Allow extra depth for cable connectors 9 8kg 21 6lbs Internally set to either 100 115 120 220 or 230 240V AC 49 62Hz Power consumption 8W typical 12W maximum These specifications are subject to change without notice Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 MAINTENANCE AND SUPPORT Service and Maintenance dCS audio products are designed not to need regular maintenance and contain no user serviceable parts apart fro
3. You should have a clear idea of what you expect to gain before updating to the latest issue We recommend that you keep your software up to date Check the dCS web site for the latest software updates This manual is for Scarlatti Clock software version 1 0x Issue 1 00 The first issue Filename Scarlatti Clock Manual v1_0x doc English version
4. warn you that the unit is running When the menu is open the DISPLAY button changes to the lt button used to page backwards through the menu DITHER Button Press the DITHER button C to turn the Dither feature on and off This dithers the clock edges in a controlled way to exercise the phase locked loops in the source and DAC Try it and decide for yourself whether you prefer Dither on or off When the menu is open the DITHER button changes to the button used to page forwards through the menu Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 Display In normal use the clock frequency is shown at the top of the display D for example 44 1kHz WAN The icons at the bottom show the current settings or operating conditions From the left these are Temperature stabilised if the icon is displayed Dither on if this icon is displayed Coupling menu setting TTL is shown the alternative is Bipolar If the unit is locked to an external reference SYNC is displayed instead If an external reference is connected but the unit cannot lock to it SYNC is displayed greyed out Details of the menu displays are shown in the Menu section on page 12 FREQUENCY Button Use the FREQUENCY button E to set the clock frequency to either 44 1kHz or 48kHz The usual setting is 44 1kHz MENU Button Press the MENU button F to open the menu select menu pag
5. DISPLAY Button DITHER Button Display FREQUENCY Button MENU Button Remote Control Receiver Rear ANG a a a a Word Clock Outputs Ref Input 1394 Interface SUC Connector Mains inlet Te Menini EO Using the Menu INFORMATION Menu CLOCK SETTINGS Menu DISPLAY SETTINGS Menu OOS CIN G AUN ON aiina eras tates anne ra Maintenance and Suppott ccccccsssscseeeeeeseceeesssseeeeeeeeeeensseeeeeeseeeoessnseeeees Service and Maintenance Replacing a Blown Mains Fuse Cleaning the case Limited Warranty If you need more help Software History Filename Scarlatti Clock Manual v1_0x doc Software Issue 1 0x June 2008 English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 USING THE dCS Scarlatti Clock FOR THE FIRST TIME Congratulations on purchasing your dCS Scarlatti Clock Before using your unit please read this section and the Step by Step Guide This will enable you to set the unit up quickly and safely with your hi fi system From time to time dCS will release updated software on CD that you can install yourself using the CD Update feature Please check our web site occasionally to see if new Scarlatti software is available or consult your dealer What s in the box Check that the box contains the following items dCS Scarlatti Clock Manual and Menu Setup Guide Power cable 3x BNC cables spare fuses Notify your dealer as soon as possible if anything is missing or damaged
6. Warranty on this product will be void if the product is misused in any way any unauthorised modifications or repairs are carried out the product is not used in accordance with the Operating Conditions stated in this manual the product is serviced or repaired other than by dCS or our authorised service agents the product is operated without a mains earth or ground connection the unit is returned inadequately packed dCS reserve the right to apply a service charge if a product returned for warranty repair is found to be operating correctly or if a product is returned without a returns number being issued This warranty covers parts and labour only it does not cover shipping charges or tax duty Our dealers or distributors are NOT authorised to extend the terms of this warranty dCS cannot accept responsibility for any attempt to do so Products re sold by dCS on a used basis may be subject to reduced warranty terms Obtaining Service Should you encounter a problem contact your authorised dCS dealer for advice quoting the model the full serial number software version number and giving a detailed description of the fault Your dealer will advise you fully on actions that need to be taken When returning a unit the original packaging should be used to avoid transit damage Replacement packaging sets may be purchased from dCs During the Warranty period there will normally be no charge for parts or labour Operating Con
7. We suggest that you retain the original packaging for possible future use If this is not possible replacement packaging can be ordered from dCS or our distributors Details can be found on our web site at www dcsltd co uk The Scarlatti Transport is supplied with a programmed Philips Pronto remote control If you do not have a Scarlatti Transport in your system a programmed Pronto can be ordered direct from dCS as an optional extra Safety Notice Your dCS Scarlatti Clock contains no user serviceable parts DO NOT attempt to open the case as there are potentially dangerous voltages present inside In the event of the unit developing a fault please contact your dealer in the first instance Mains Voltage Setting Before connecting the power cable to the unit for the first time please check that it has been set to the correct operating voltage for your mains supply The unit s voltage setting is shown on the label beneath the mains inlet on the rear panel If this does not match your local supply voltage DO NOT attempt to use the unit Contact your dealer to have the unit reset Using the unit with the wrong mains setting for your local supply may result in serious damage to the unit and will invalidate the warranty Do not attempt to reset the voltage yourself Power Cables If you wish to use a power cable other than the one supplied please ensure that it is a good fit to the mains inlet and is not so heavy and inflexible as to place st
8. dCS Scarlatti Clock Digital Audio Master Clock User Manual Software Release 1 0x June 2008 Data Conversion Systems Ltd 2007 8 Price UK 8 00 Euro 12 00 All rights reserved No part of this publication may be reproduced stored in or introduced into a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of dCS Any person who does any unauthorised act in relation to this publication may be liable to criminal prosecution and civil claims for damages Information contained in this manual is subject to change without notice and whilst it is checked for accuracy no liabilities can be accepted for errors dCS is Data Conversion Systems Ltd Company registered in England No 2072115 dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 Filename Scarlatti Clock Manual v1_0x doc Page 2 English version dCS Scarlatti Clock User Manual CONTENTS CONIEenNiS iii end nce es eke E en eigen Using the dCS Scarlatti Clock for the first time ii What s in the box Safety Notice Mains Voltage Setting Power Cables Mains Regenerators Positioning the unit Disposal at end of life STEP BY STEP GUIDE Preliminaries The GOLDEN RULES for using a Master Clock Connecting the system for DSD Connecting the system for Dual AES Using an External Reference Froni nelle POWER Button
9. ditions The supply voltage must remain within 10 of the A C voltage specified on the back panel The supply frequency must be in the range 49Hz to 62Hz Ambient temperature range 0 C 32 F to 40 C 104 F non condensing Do not install the unit near heat sources such as radiators air ducts power amplifiers or direct strong sunlight e If in doubt the easy test is the unit is happy to work anywhere a human is Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 If you need more help In the first instance you should contact your dealer If they cannot resolve the issue contact your national distributor Manufactured by dCs Ltd Mull House Great Chesterford Court Great Chesterford Saffron Walden CB10 1PF UK www dcsltd co uk This user manual may be downloaded free of charge from our web site A bound copy of this manual may be ordered from dCs Software History dCS products make extensive use of software configurable chips FPGAs and DSPs This gives us the ability to update our products to add extra features update digital interface standards or make performance improvements by loading new software Occasionally a hardware update may be necessary also to increase the capacity of the electronics add extra connectors or extra front panel controls Please note that not all software updates make an earth shattering change
10. es and change settings See the Menu section on page 12 for information on using the menu features Remote Control Receiver Aim the remote control handset towards the receiver G for best sensitivity Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 REAR PANEL AJ 50 60 Hz 30W FUSE T_T 500mAL Figure 3 Rear panel Word clock is used for synchronisation only it does not carry digital data Word Clock Outputs The unit has eight identical Word Clock Outputs G all of which carry standard word clock at either 44 1kHz or 48kHz Ref Input The Ref In connector H allows the unit to be locked to an accurate external reference such as an atomic clock or a GPS clock With the Coupling menu page set to TTL the unit will lock to an external word clock at 32 44 1 48 88 2 or 96kHz With the Coupling menu page set to Bipolar the unit will lock to a 10MHz reference As the Scarlatti Clock is a grade 1 master clock there is nothing to be gained by locking it to a less stable or less accurate reference 1394 Interface There is provision for fitting an IEEE 1394 interface I which may be added at a later date As a Master Clock does not generate or accept digital data this will be used for control purposes only SUC Connector The SUC connector J is an RS232 interface primarily used to remotely control the unit during automated testin
11. g Please contact dCS for advice on using this interface with a household automation system Note that we recommend using infra red remote control instead Mains inlet Power is connected via a standard IEC320 connector K protected by a fuse L and isolated by a 2 pole power switch M Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 THE MENU Press Step gt to move along the Menu press lt Step to move back Press Select to set a menu option or change options i Unit Version Contact lametta CDUpdate gt A V X XX Sain sii Displays the loade software issues an serial number Starts software update from a dCS CD Displays dCS Displays the unit contact details status SA Sets the External Input to detect TTL or bipolar AC Restores standard factory settings Settings Contrast Test Displa gt Sets the display Adjusts the display Runs a display test brightness contrast routine Figure 4 The menu sequence Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 Using the Menu The menu gives the user access to a range of additional features It also allows new features and performance enhancements to be added at a later date by software upgrades The menu is controlled by four buttons Press the MENU button to open the menu or selec
12. m the mains fuse If your unit is damaged in any way please contact your dealer Replacing a Blown Mains Fuse There is a mains fuse below the power inlet accessible from the outside of the unit If the fuse blows it may be changed by the user The current consumption of the unit is very low so it only blows if power surges occur or there is a fault in the unit Usually power surges cause no other damage but if the fuse blows repeatedly on replacement some other damage will have been done and the unit must be returned to dCS for repair Fuse type 20 x 5mm 10 5 amp L fuse If the fuse should fail it is essential that it is replaced with one of the same type and rating Failure to do so could result in damage to the unit risk of fire or electric shock and will invalidate the guarantee Referring to the diagram below remove the power cable use a small flat bladed screwdriver to pry up the tab on the fuse carrier A and pull it out Push the blown fuse out of the clip in the carrier B and dispose of it Fit a new fuse in the clip C and push the carrier back into the unit so that it clicks home Spare fuses are provided with the unit C pie Cleaning the case The front and back panels of your dCS equipment are machined from very high grade aluminium Great care has been taken to create the finish of the aluminium throughout the engineering process from the raw solid material to the finished piece To remove loose dust or finge
13. r marks from the case we recommend that you use a clean dry lint free cloth To restore the finish on the front and back panels we recommend applying small quantities of a lanolin based cleaner using a clean dry lint free cloth and then wiping off Do not allow lanolin to collect around the buttons Small amounts of glass cleaner containing ammonia may be used to clean other surfaces but avoid spraying onto the connector contacts Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 Limited Warranty General dCS warrants this product against defects in materials and workmanship for a period of 3 years from the date the unit was originally shipped from dCS During the warranty period dCS will repair or at our absolute discretion replace a faulty product Warranty repairs must only be carried out by dCS or our authorised service agents Please contact your dealer if your unit requires service Your dealer should have completed on your behalf an Owner Registration form at the time of sale and returned it to dCS On receipt of the Owner Registration form dCS will add your contact details to our customer database dCS will use this information for warranty purposes only we will not contact you directly for reasons relating to sales and marketing This warranty applies to the original owner Warranty Exclusions The Warranty does not cover wear and tear The
14. rain on the mains inlet Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 Mains Regenerators We do not recommend the use of mains regenerators However if you do wish to use a mains regenerator with variable voltage and frequency we recommend that you set the voltage to match your local voltage and the frequency to either 50Hz or 60Hz ONLY Damage caused to your Scarlatti Clock by misuse of a mains regenerator or by a malfunctioning mains regenerator is not covered by the warranty Positioning the unit Units in the Scarlatti range are designed to be mounted on separate shelves of a rack and must NOT be stacked directly on top of each other Place each unit on a firm vibration free base allowing convenient connection to the other parts of your system To prevent overheating we recommend that you leave some free space around the unit to allow for ventilation Disposal at end of life The symbol indicates that this product should not be treated as normal household waste It should be recycled so please take it to an approved collection facility Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 STEP BY STEP GUIDE This section guides you through setting up the unit for basic operation Preliminaries The Menu Setup Guide sheet details the menu structure and details the two mos
15. set to 44 1kHz it may be used with DSD based systems CD systems without an upsampler running at 44 1kHz or CD systems upsampling to 88 2kS s or 176 4kS s Dual AES When the Scarlatti Clock is set to 48kHz it may be used with a DVD player or DAT recorder fitted with a Word Clock Input running at 48kS s or upsampling to 96kS s Dual AES or 192kS s Dual AES To make best use of the Scarlatti Clock all the digital audio units in the chain should be locked to it Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 Connecting the system for DSD Most owners will use the Scarlatti Clock to clock a Scarlatti stack at 44 1kHz If necessary use the FREQUENCY button to set the Clock to 44 1kHz Connect one of the Clock outputs to the Word Clock inputs of the transport and the DAC Connect a 1394 cable between the DAC and the transport Select the DAC s 1394 input The transport will automatically slave to the Clock and display Sync Use the DAC s SYNC button to set it to WCIk Connect the DAC s Analogue Outputs to a power amplifier or preamplifier Set the DAC Volume control to a suitable level and play a disc Set the Clock s DITHER feature on or off as you prefer Scarlatti Transport CHI SI l OUTPUTS AES 1 _ Scarlatti Clock A o AES2 RCA BNC Tosunk Qa 1394 9 50 60 H
16. t a setting Press the button to page forward through the menu Press the lt button pages backward through the menu Press the POWER button to close the menu or just wait 5 seconds Alternatively use the remote control to access the menu Use the Menu Guide sheet to help you find the right menu Each unit in the range has either three or four top level menu pages The INFORMATION menu gives software issues serial number contact details and unit set up details Each model has a different SETTINGS menu which allows you to set some features that are not directly accessible from the front panel The DISPLAY SETTINGS menu is used to adjust and test the display The SIGNAL GENERATOR menu on the Transport and DAC only contains test and set up routines Use the button to move the highlight to the menu you want then press the MENU button to select it The next menu level down is displayed Use the button to move the highlight to the menu page you want then press the MENU button to display the information or change the setting gt Select the exit icon E to go back to the previous menu level Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 INFORMATION Menu The Version page displays the software versions loaded in the unit and the full serial V X XX number Please have this information ready if you contact your dealer for any reason a
17. t common set ups For all of the Word Clock Outputs and the Ref Input use 750 coax cables fitted with BNC plugs Connect the power cable supplied to the power inlet on the Clock rear panel plug the other end into a convenient power outlet Please do not use an excessively heavy or inflexible power cable as this may damage the power inlet connector Press the Power button and wait about 30 seconds while the Clock configures itself The display will show in sequence Scarlatti and either 44 1Hz or 48kHz If the unit is likely to be set in an unfamiliar state you can reset it as follows Press the Menu button press the button once then the Menu button again to display the Clock Settings menu Press the lt button a few times to highlight the Factory Reset menu page Press the Menu button and wait a few seconds while the unit resets itself The GOLDEN RULES for using a Master Clock e The source equipment MUST be locked to the Master Clock If it is not you will either have locking difficulties or hear occasional clicks and the advantages of using the Clock will be lost Some non dCS CD transports DAB radios and other equipment do not have a Word Clock Input and so CANNOT be locked to a Master Clock e The clock frequency MUST match the sample rate s used in the system If it does not the system cannot lock and the DAC may remain muted Please check the manuals for the equipment used in your system When the Scarlatti Clock is
18. you can lock the Scarlatti Clock to it These sources are even more accurate than the Scarlatti Clock but note that low jitter and stability are more important than absolute accuracy Connect your system for DSD or Dual AES as you prefer Use another BNC cable to connect the 10MHz output from the external reference to the Scarlatti Clock s Ref In connector Open the Clock s menu and set the Coupling menu page to Bipolar The Clock should lock to the external reference and display Sync Set the DAC Volume control to a suitable level and play a disc Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 FRONT PANEL Scarlatti Figure 2 Front panel POWER Button To switch on ensure the rear panel switch is set to and press the POWER button A on the front panel once Note that the unit cannot be turned on from the remote control To set the unit to sleep mode press the POWER button once The main display will turn off the clock outputs will mute and the LED over the button will light Press again to return to normal operation To switch off hold down the POWER button for about 5 seconds until Power Down appears on the display then release it When the menu is open press the POWER button to close the menu DISPLAY Button Press the DISPLAY button B to turn the main display off and on When the display is off the LED over the button will light to
19. z 30W FUSE T500mAL Scarlatti DAC 50 60 H 1394 z 50W JJ FUSE SUC T500mAL Balanced or Unbalanced Analogue Outputs To pre or power amplifier inputs Figure 1 Using the Scarlatti Transport DAC and Clock together Filename Scarlatti Clock Manual v1_0x doc English version dCS Scarlatti Clock User Manual Software Issue 1 0x June 2008 Connecting the system for Dual AES Owners with an Upsampler may prefer to use it to run the DAC at 176 4kS s If necessary use the FREQUENCY button to set the Clock to 44 1kHz Connect one of the Clock outputs to the Word Clock inputs of the transport the Upsampler and the DAC Connect an AES cable between the transports AES output and the Upsampler s AES input select that input Set the Upsampler to 176 4kS s Connect the Upsampler s AES1 amp 2 outputs to the DAC s AES1 amp 2 inputs and select the DAC s Dual AES input It may be necessary to turn Dual AES mode on in the menu The transport will automatically slave to the Clock and display Sync Set the Upsampler to sync to the external word clock Use the DAC s SYNC button to set it to WCIk Connect the DAC s Analogue Outputs to a power amplifier or preamplifier Set the DAC Volume control to a suitable level and play a disc Set the Clock s DITHER feature on or off as you prefer Using an External Reference If you have a GPS receiver or an atomic clock with a 10MHz output
Download Pdf Manuals
Related Search