Dakota Digital UTV-1200 User's Manual
Contents
1. 8 Ifthe settings are all correct press and release the left switch Water temp display will read YES 9 Press and release the right switch to preset the odometer hour meter to the new value Oo eee N SERVICE METERS This gauge has two service meters These are a countdown hour meter and a countdown odometer Both service meters can be disabled or enabled independently This allows for setting of two individual service points one based on engine run time the other based on odometer This could also allow for setting a service point on whichever service point comes first hourly or odometer When the setup point is reached SEF ICE IUE will scroll in the message center Pressing either switch will clear the message until the next time the key is turned on Once the service has been done use the left switch to select the service meter that is due display will show a negative value or zero Press and hold the right switch to reset the service meter to the value set in setup The service meter can be disabled by selecting OFF in setup If a new value is set for the service meter and the meter was previously set to iF the service message may immediately be displayed Reset the service meter to begin a new countdown page 4 MAN 650244 A OPTION DIM OUT The dim out option allows the dim output to be turned on or off The dim output is used if you have installed other Dakota Digital gauges and would like this gauge to also cont2. IMPORTANT NOTE Dakota Digital This gauge has an hour meter and odometer preset option available only for the first 1 0 engine hour and 10 UTV 1200 miles 16km See ODO HR i PRESET for instructions Multi Gauge for 2008 Yamaha Rhino Setup mode indicator Battery voltage display Fuel level display Oil pressure display Tach bar Park brake indicator i j 4 wheel drive Speed display LN CELT a LIL J Lt Ls ob Lf Diff tial lock Of Ly o0 0 0 cater Gear position _ m 7 a display Wu i im im i AC CY C R wM M Nei i N TEAN AN i i Right switch Left switch Speed unit indicator Water temperatur display Message center E wire 12v dim output O Connect to O oil pressure RED wire warning output ground output i sender Operation menu Left switch functions Pressing the left switch during normal gauge operation will move through the below commonly viewed functions for convenience OO Odometer A Clock hold left switch to set Setting clock Left switch press moves between hours and minutes Right switch press changes current value Hold left switch again to exit clock set mode a Hourmeter Right switch functions Pressing the right function switch during normal operation will scroll through the following display functions A heading will first appear a
3. is authorized to assume for Dakota Digital any liability other than expressed herein in connection with the sale of this product Dakota Digital 4510 W 61ST St N Sioux Falls SD 57107 Phone 605 332 6513 FAX 605 339 4106 www dakotadigital com dakotasupport dakotadigital com Copyright 2009 Dakota Digital Inc page 6 MAN 650244 A
4. a Gauge will dim early when more light is on gauge face St Enables disables dim output for other gauges Li Dim output will be high when gauge is dimming EE Dim output will be disabled default iT selects which gauges provide a warn out signal on warn out wire default all on I DUT Gauges that provide signal out are lit up left switch to change right switch to save N Warn output wire is disabled ei Adjust clock speed for accuracy N Subtract 7 seconds from clock every 24 hrs AGEL No adjustment to factory clock speed default GEE Add seven seconds to clock every 24 hrs J Allows presetting of odometer value on initial install not available after 10 miles 16km HA Allows presetting of hour meter value on initial install not available after 1 0 hrs AIN Returns to info menu NE Leaves setup menu if selected page 3 MAN 650244 A ADDITIONAL SETUP NOTES SPEED AUTO This setup option allows calibrating to a known mile or kilometer By default the speed is calibrated to use the Rhino Factory speed signal Calibration should only be needed if the factory calibration is no longer correct due to changes to tires or gearing 1 Start with vehicle at the beginning of the marked mile or kilometer and turn the key off 2 Start engine while holding the left switch to enter setup 3 Select speed option in setup and select appropriate unit if you will be calculating to a Known kilometer choose KPH else choose MPH 4 Select the Auto opti
5. by UPS or insured Parcel Post Be sure to include the RMA number on the package and include a complete description of the problem with RMA number your full name and address street address preferred and a telephone number where you can be reached during the day Any returns for warranty work must include a copy of the dated sales receipt from your place of purchase Send no money We will bill you after repair Dakota Digital 24 Month Warranty DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it under normal use and condition be proven defective in material or workmanship within 24 MONTHS FROM THE DATE OF PURCHASE such defect s will be repaired or replaced at Dakota Digital s option This warranty does not cover nor extend to damage to the vehicle s systems and does not cover removal or reinstallation of the product This Warranty does not apply to any product or part thereof which in the opinion of the Company has been damaged through alteration improper installation mishandling misuse neglect or accident This Warranty is in lieu of all other expressed warranties or liabilities Any implied warranties including any implied warranty of merchantability shall be limited to the duration of this written warranty Any action for breach of any warranty hereunder including any implied warranty of merchantability must be brought within a period of 24 months from date of original purchase No person or representative
6. fter each press to display the currently selected function After about 2 seconds the display will show the data for the selected function Data Description AG Trip A hold right switch to reset i A Trip B hold right switch to reset SRV kM 5 Oooo Count down Service odometer if enabled hold right switch to reset z 1 00D Count down service hour meter if enabled hold right switch to reset IPH GGO KH Alternate speed display hold right switch to change primary unit oog Tachometer displays in information center page 1 MAN 650244 A oJen 10 i 72 I J ao io t 41 J k bY 574 E a A Ls INSTALLATION 1 Disconnect the battery to prevent possible damage to the electrical system or gauge during install Remove the stock gauge or indicator panel See service manual for removal instructions The UTV gauge will mount in this mounting location 3 Remove the seats console engine cover front engine cover and center floor front drive shaft cover refer to service manual This allows access to sensor locations on the engine and wire routing locations 4 Oil sender installation a Turn the provided oil sender into the oil pressure sender hose fitting Sealant tape may be used on this sender as the gauge provides ground through the harness b Tighten the sender into the fitting with appropriate wrenches c Cut either one of the hoses going to the oil cooler toward the front of the engine to allow t
7. he installation of the oil sender T fixture It doesn t matter which hose Have some rags handy as the hose will leak some oil d Place a hose clamp onto each end of the cut oil cooler hose Two hose clamps are included with the gauge e Insert the fitting into the hose and tighten hose clamps onto hose and fitting f Remove terminal thumb nuts on oil pressure sender and put ring terminals from oil sender harness onto the terminals Secure l with terminal thumb nuts The sender terminals don t have a pola so just connect one wire to each terminal g Route oil sender harness up to the gauge mounting location Zip tie the harness with provided zip ties so that it will not be pinched or damaged h Be sure to check engine oil level and add oil if needed 5 Route the wires from the UTV gauge through the hole in the gauge opening and place gauge into opening Secure the gauge with the three provided washers and thumb nuts 6 Plug the four pin connector from the oil pressure harness into the four pin connector in back of gauge 7 Locate the 6 pin gauge connector in the Rhino harness This connector will be located close to the gauge mount location on the under hood side of the dash panel 8 Plug the 6 pin gauge connector 6 pin connector on the Rhino 9 Reconnect battery 10 Turn the key on and verify that the gauge functions as expected 11 Start engine and check for oil leaks Shut off engine 12 If there are no oil leaks reinstall the floor
8. ice meter operation is not desired disable service meter by setting to OFF in the setup menu EAR OY tOERR S4 is The Rhino engine computer is sending See your Yamaha dealer for appropriate service displayed in the message error codes to the gauge center ERR Hiis displayed in Gauge has poor bus connection to Check for good connection to gauge harness message center Rhino engine computer ERR He is displayed in Bus wire is always in high state Check for shorts to 12V on bus wire message center Gauge bus circuit damaged Repair needed ERR HA is displayed in Bus wire is shorted to ground Check for shorts to ground on bus wire Check for message center proper connection to Rhino harness GAUGE WIRE COLOR CHART VIOLET BLACK Data bus BLACK RED Keyed power WHITE BLUE Ground WHITE Fuel sender GREEN BLUE Constant power page 5 MAN 650244 A SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of its product line In addition technical consultation is available to help you work through any questions or problems you may be having installing one of our products Please read through the Troubleshooting Guide There you will find the solution to most problems Should you ever need to send the unit back for repairs please call our technical support line 605 332 6513 to request a Return Merchandise Authorization number Package the product in a good quality box along with plenty of packing material Ship the product
9. o 500 mi or 800 km when resetting service odometer ae Service point can be set in 500 mi 800km increments 1500 420900 Sets service to 7500 mi or 12000 km when resetting service odometer N Returns to info menu TACH Tachometer gauge menu PIATE Sets update rate for tachometer readout screen J tach updates at slowest rate default Lo a u i Gq Ez Ly fastest update on tach UARN Sets RPM warning point default 5500 RPM i 250 Minimum warning point of 2250 RPM Warning point can be set in 250 RPM increments 4 Maximum warning point of 9750 RPM F Sets service hour value used when resetting count down service hour meter JFF Service hour meter disabled default 7 Minimum service hour set point Service hour reset point can be setin 10 hr increments iT Maximum service hour set point AIN Returns to info menu UDES Gauge option menu HI Set high voltage warning point default 15 4V La Set low voltage warning point default 11 1 V 7 Set low oil pressure warning point default 9 PSI HI Set high water temp warning point and set temperature unit default 251F TE F IEG L Select temp unit press left switch to change right switch to save WTR HI Select high warning left switch to change right switch to save N Returns to info menu JPTION Option menu Lr Adjust dimming point on gauge FE Dimming function is off LVL Gauge will dim when light on gauge face is very low default ia 7 selectable dimming levels A
10. on The gauge will light all the displays and the speed display will read CL 5 Begin driving the mile or kilometer The message center will read the number of pulses read from the speed signal This value cannot be used to determine if a mile or kilometer has been driven 6 At the end of the mile or kilometer stop the vehicle and press the right switch to save the new speed calibration The gauge will return to the speed setup menu SPEED ADJUST This setup option allows adjustment to speed while driving By default the speed is calibrated to use the Rhino Factory speed signal Calibration should only be needed if the factory calibration is no longer correct due to changes to tires or gearing 1 Start vehicle while holding the left switch to enter setup 2 Select speed option in setup and select appropriate unit if you will be calculating to a Known kilometer choose KPH else choose MPH 3 Select the ADJUST option The gauge will light all the displays and the message center will read iui 7 4 Follow another vehicle traveling at a constant known speed Hold the left switch to begin increasing the speed reading To decrease the speed reading release the switch and press and hold the switch again 5 The direction of adjustment will change each time the switch is released 6 When the speed has been adjusted press the right switch to save the new speed calibration The gauge will return to the speed setup menu ODO HR PRESET Within the fir
11. panels engine covers and seats as described in the service manual 13 Installation is now complete If you experience difficulties check the troubleshooting section in this manual SETUP a To enter setup for speed calibration changes Press and hold left switch while starting engine b To enter setup for all other setup options Press and hold left switch while turning the key on Press the left switch to move through the menus or change the settings after a menu option is selected Hold the left switch for more than 2 seconds to scroll through options or settings Press the right switch to select a menu option or to save a setting and go back to the menu Release switch to enter setup menu z Information menu Displays software version aa Current software version CHE Displays current speed cal value SOO Current speed cal value TIN Returns to info menu page 2 MAN 650244 A SPEER Speed gauge menu NIT Select unit for speed Toggle between MPH and KPH select unit to use for calibration J Auto calibrate speed to a marked mile or kilometer Pulls up all values CL on speed and speed pulses in odometer Press Right switch to finish cal and save value 17 Adjust speed cal while driving 7 Each press of left switch toggles direction of adjustment right switch to save and exit GRP MI BRV RM Sets value of service odometer set when service odometer is reset DEF DEF Turns off the count down service odometer default Soo BOD Sets service t
12. rol the dimming of these gauges If the dim out option is turned on 12v is sent out on the dim out wire when the gauge is dimming In this mode the gauge will be either in dim mode or full brightness mode If no other gauges are to be dimmed this option can be set to off In this mode the gauge will fade when dimming and gauge dimming will be less noticeable TROUBLESHOOTING PROBLEM CAUSE SOLUTION Gauge does not light up Gauge has bad ground or power Check connections to wiring harness and check wiring harness and gauge wires for pinched or broken wires Speed reads incorrectly Speedometer needs to be recalibrated See setup for speed calibration instructions Gauge does not dim Dim level is set to off or set too low Set dim level to higher level see setup Gauge is always dim Dim level is set too high Set dim level to lower level See setup Light sensor over left switch is covered Make sure left side of lens is not covered EEE is displayed in fuel or No sender connected Check proper connection to sender Check for oil display broken or pinched sensor wires is displayed in fuel or Sensor wire is shorted to ground Check sensor wire harness for correct connection oil display to sensor Check for pinched or broken sensor wire harness SERVICE Hue is scrolled One of the countdown service meters Perform service and reset service meter by in the message center has reached zero holding right switch when service meter is displayed If serv
13. st 10 miles 16 km and 1 0 engine hours after first installing the gauge the option is available for a ONE TIME preset of the odometer and hour meter to the reading s of the previous gauge If this option is not used within the first 10 miles 16 km or 1 0 engine hours or an incorrect reading is saved the gauge will need to be returned to Dakota Digital for any odometer hour meter adjustment The procedure to preset the meters is as follows 1 If setting odometer select 57 GIG option in setup If setting hour meter select SET HF 2 For odometer preset verify that correct unit is displayed above message center If not turn key off to leave setup and use unit option under speed to set correct unit NOTE Preset MUST be done with correct unit or odometer will not be set correctly The current odometer hour meter value is displayed with the first digit blinking Press and release the left switch to change the digit Press and release the right switch to move on to the next digit Repeat step 4 until all digits are set After tenths digit is set press and release the right switch Water temp display will read no Check the current unit if in odo preset and the odometer hour meter value to make sure it is correct If not press and release the right switch to go back and make changes NOTE Check the displayed odometer value VERY carefully before next step After selecting yes you will no longer be able to change the odometer hour meter
Download Pdf Manuals
Related Search