Dakota Digital MCL-36K-TCH User's Manual
Contents
1. if you are setting up the GEAR display All other gauge functions and gauges can be set without running the engine CL CLOCK SETUP The time is displayed on the smaller display below the RPM and is the first setup menu since it is the only setting that requires change once the initial calibrations are complete To set the clock press and hold the switch while turning the key on Release the switch The RPM display should show CL press and hold switch until is displayed Release the switch The lower display will show the current hours Press and release the switch to change the hours press and hold the switch to change to the minutes Release the switch The lower display will show the current minutes Press and release the switch to change the minutes press and hold the switch to change to the time adjust calibration Release the switch The lower display will show CAL and a number from 8 to 7 This allows the clock to be adjusted seconds per day e Press and release the switch to change the CAL value press and hold the switch to save this and exit the clock setup n I9HE NIGHT DIMMING Your display system has a dimming feature that dims the display intensity Normally the system is at full brightness for daytime viewing The tachometer has a light sensor that will provide a signal to the other gauges to reduce the brightness at night The level of darkness before the gauges dim can be adjusted in the tachometer s2. to 50 intensity The GREEN wire is used for entering setup and for changing the message screen This can be wired to a momentary push button switch and the other side to 12V If an MCL 36K SPD gauge is also being installed then this can connect to the green wire from the speedometer Back View of Gauge The GREEN wire The BLUE wire can be can connect toa connected to other Dakota Digital Dakota Digital MCL 3K MCL 36K SPD or MCL 36K gauges gauge to allow the The tachometer will factory switch to be automatically dim the used for setup ora other gauges when it momentary push gets dark button switch can be connected Switch Input active high 12V GREEN wire 12v i Momentary push button switch KEY ON POWER or GREEN wire from MCL 36K SPD Dim Output active high 12V Ye BLUE wire Optional connection to BLUE wire on other MCL 3k gauges 2 MAN 650335 FUNCTION SWITCH If an MCL 36K SPD gauge is installed then the factory speedometer push button switch is used as the main function switch otherwise a push button switch should be connected and mounted to allow access to all of the gauge features The function switch is used for setup and for adjusting the clock The function switch can also be used to change the tachometer display If an MCL 36K SPD gauge is also installed be sure the speedometer is displaying the odometer to avoid resetting any of the other settings before attempting to change the tachometer Press and
3. wiring connections Green wire should have 12 volts correctly when the switch is pressed Cruise Engage indicator Loose or incorrect connection to indicator wire Check that the appropriate indicator wire has about 12 volts does not work when the indicator should be off and about 0 volts when the indicator should be on ECM performance tune Stock service tools look for all stock gauges Unplug MCL 3006 and reprogram ECM MCL 3006 can be or reprogramming fails plugged back in as soon as reprogramming is complete SERVICE AND REPAIR DAKOTA DIGITAL offers complete service and repair of its product line In addition technical consultation is available to help you work through any questions or problems you may be having installing one of our products Please read through the Troubleshooting Guide There you will find the solution to most problems Should you ever need to send the unit back for repairs please call our technical support line 605 332 6513 to request a Return Merchandise Authorization number Package the product in a good quality box along with plenty of packing material Ship the product by UPS or insured Parcel Post Be sure to include the RMA number on the package and include a complete description of the problem with RMA number your full name and address street address preferred and a telephone number where you can be reached during the day Any returns for warranty work must include a copy of the dated sales receipt from yo
4. CTORY DEFAULT SETTINGS FOR SETUP MENUS Below is a list of factory gauge settings and what can be adjusted in the setup menus You can calibrate and adjust the tachometer as often as you wish however it should only need to be set once The only gauge that may require setting after the initial install is the Clock function on the tachometer so it is the first setup menu Clock Cal 0 range 8 7 Night Dimming 1 darkest Display Update 3 fastest 1 8 sec RPM Warning 5500 range 2200 9900 3 MAN 650335 TACHOMETER SETUP Main Menu Sub Menu Description EL set clock time ECH n IJHE set night dimming level uPodREE set RPM update rate for digital readout udfra set RPM shift warning point 9EAr transmission gear programming Press and hold the switch while turning the key on Release the switch Press and release the switch until ECH is displayed then press and hold switch until is displayed The RPM display will show SEE and the lower display will show n dhe Press and release the switch to move through the different menus press and hold the switch to select a menu option Note The tachometer calibration may require you to hold the switch while starting the bike but only if you are going to adjust set the GEAR programming since you will have to ride the bike Some ignition systems may disrupt power to other circuits when cranking causing the gauge to reset this is why you must hold the switch while starting
5. WWW DAKOTADIGITAL COM MCL 36K TCH Thank you for purchasing the Dakota Digital MCL 36K TCH gauge for your Harley Davidson Touring bike This gauge is designed to be a direct plug in replacement for all touring models from 2004 2011 This is part of a six gauge package for touring models so you can add additional gauges as you choose INSTALLATION First read and familiarize yourself with all of the components and this manual The first step is to remove the seat and disconnect the negative side of the battery as with any electronic install Once the battery is disconnected you are ready to start Remove the outer fairing this will vary from model to model so please follow the service manual to expose the wiring and gauges Don t be alarmed by the amount of wires behind the fairing this is a direct plug in gauge and these detailed instructions will guide you through it Street Glide with outer fairing removed Road Glide with outer fairing removed REMOVAL OF FACTORY GAUGE ULTRA FLHT amp FLHX STREET GLIDE batwing fairings Unplug the tachometer Remove the screws securing the clamp that holds the gauge in place and pull it out through the front of the fairing Save the screws gasket and clamp to be reused when you install the new Dakota Digital gauge ELA Unplug the factory tachometer Unscrew the clamp and remove gauge 1 MAN 650335 FLTR ROAD GLIDE You will need to remove the speedometer and tachometer i
6. etup e Press and release the switch until n 9H is displayed then press and hold the switch until is displayed e Release the switch The update setting will be displayed i late darkest mid 3 early lightest GFF e Press and release the switch until the desired setting is displayed e Press and hold the switch until is displayed to save the setting uPdALE Display update setup The display update will select how quickly the tachometer reading will respond e Press and release the switch until uPdArE is displayed then press and hold the switch until is displayed e Release the switch The update setting will be displayed i slow mid 3 fast e Press and release the switch until the desired setting is displayed e Press and hold the switch until is displayed to save the setting 4 MAN 650335 Tachometer Setup Continued LJArn RPM warning setup Press and release the switch until G JArn is displayed then press and hold the switch until is displayed Release the switch The current warning point will be displayed Press and release the switch until the desired setting is displayed Press and hold the switch until is displayed to save the setting 3JEAr Gear indicator setup This tachometer has a single digit display for gear position The gauge can learn the positions based on speed and RPM so no sensors are needed just what you ve already plugged in It
7. hold the switch for about 4 seconds to change the tach menu Press and hold the switch for about 6 seconds to reset the high RPM recall while it is displayed The tachometer only has two display modes as follows TACH MEN CLOCK gt 2 00 12 hour clock HI RPM gt ooog high RPM recall GAUGE SETUP AND CALIBRATION The function switch discussed above is used to enter setup mode for all of the gauges If you are only installing one or a couple Dakota Digital MCL 3K gauges then setup may seem a little strange since they are designed to work as a set The first step in the setup procedure is to select which gauge you are going to adjust Each gauge will either show a number or a label If the gauge is showing a label then that gauge will be selected to enter setup All of the other gauges will exit setup and allow the selected gauge to be changed To get into setup press and hold the function switch while turning the key on Press and release the switch to advance through the menus below when on the desired option press and hold the switch to select setup for that particular gauge function Speed Tach Oil PSI Oil Temp Fuel Volt 1 IRS CL a cle e Slee jl 5 ae ee 2 5Pd Ten ea ed en a 3 ECH sgan a aa 4 4 4 P5 4 4 4 5 5 5 5 Foof 5 5 6 6 6 6 6 Fit 6 as Bares li a eee aye ne 71 7 Wte 8 SA lee Ill eng E lll era ag 3 FA
8. mplete stop or press and hold the switch until the display shows dUneE Turn the key off and then on again to restart the gauges in normal operation verify the gear position by riding through each gear and seeing if positions agree 5 MAN 650335 Tachometer Troubleshooting guide Problem Possible cause Solution Gauge will not light up Orange wire does not have power Connect to a location that has power Black wire is not getting a good ground Connect ground to a different location Gauge is damaged Return gauge for repair see instructions Gauge lights up but tach No data from ECM Check engine trouble codes will only show zero Tach reading is erratic or Tach signal wire is loose or broken Check all wire connections and inspect wire for breaks jumps around Poor ground connection Check ground connection on tachometer engine and ignition system Update rate is too fast Reset display update speed slower Gear indicator is always Gears not programmed Program gear indicator in setup see instructions Gauge will not dim Night dimming is turned off or too low Change night setting in setup see instructions Gauge remains dim at all Night dimming is turn too high Change night setting in setup see instructions times Light sensor at bottom of gauge is covered Make sure the lower part of the lens is not covered Gauge will not enter setup Green wire 2 wire harness is not connected Check
9. nstrument bezel To do this remove two small screws on the left and right side of the bezel Lift up on the back of the bezel and slide the tab that is under the ignition switch out from under the switch cover see Photo A below Unplug the gauge connections and unplug the indicator lights so the bezel can be completely removed for easier installation of the new gauge Remove the clamp that holds the tachometer to the bezel and remove the gauge and gasket 120 5 8065 0s o M a Photo A Bezel removed Gauges Grommets removed IMPORTANT NOTE SAVE ALL CLAMPS GASKETS and SCREWS FROM THE STEPS ABOVE AS THEY WILL BE USED TO SECURE THE NEW DAKOTA DIGITAL GAUGE Next you are ready to install the new gauge into the fairing Install the gauge and secure using the original hardware that was removed clamp gasket and screws Be sure the alignment tab on the clamp lines up with the notches in the fairing Some fairings may only have one notch line up at least one tab on the clamp with the notch in the fairing this will ensure the gauges are centered and aligned correctly WIRING plug in connections Plug the original tachometer connector directly into the new gauge The BLUE wire on the small two wire plug can provide a dimming signal for other Dakota Digital MCL 3K or MCL 36K gauges The tachometer has a sensor that activates the dimming feature when ambient light is low and provides 12V out on the BLUE wire The gauge will dim
10. ur place of purchase Send no money We will bill you after repair Dakota Digital 24 Month Warranty DAKOTA DIGITAL warrants to the ORIGINAL PURCHASER of this product that should it under normal use and condition be proven defective in material or workmanship within 24 MONTHS FROM THE DATE OF PURCHASE such defect s will be repaired or replaced at Dakota Digital s option This warranty does not cover nor extend to damage to the vehicle s systems and does not cover removal or reinstallation of the product This Warranty does not apply to any product or part thereof which in the opinion of the Company has been damaged through alteration improper installation mishandling misuse neglect or accident This Warranty is in lieu of all other expressed warranties or liabilities Any implied warranties including any implied warranty of merchantability shall be limited to the duration of this written warranty Any action for breach of any warranty hereunder including any implied warranty of merchantability must be brought within a period of 24 months from date of original purchase No person or representative is authorized to assume for Dakota Digital any liability other than expressed herein in connection with the sale of this product 4510 W 61st St North Phone 605 332 6513 DIZ Sioux Falls SD 57107 Fax 605 339 4106 www dakotadigital com Vv dakotasupport dakotadigital com Copyright 2011 Dakota Digital Inc 6 MAN 650335
11. will work with 4 5 6 or 7 speed transmissions To program the gear positions begin at a section of road where you can gradually shift through all of the gears Press and hold the switch while turning the key on and starting the engine Once the engine is running release the switch Press and release the switch until ECH is displayed Press and hold the switch until is displayed Press and release the switch until SEAr is displayed press and hold the switch until is displayed The message will show Lo ECH if the engine RPM is below 1500 or to 5Fd if the vehicle speed is below 5 Begin driving in 1 gear The display should show JEAr and the should be flashing Drive at a steady speed until the i stops flashing it should only take about 20 seconds if the speed and RPMs are steady gt Optionally If the gear does not stop flashing you can manually override and jump to the next gear by pressing and releasing the switch to store the gear position quicker Shift to 2 gear and drive at a steady speed The display will change to a flashing 2 Wait until the 2 stops flashing then 3 should start flashing shift to the next gear and continue gt Optionally If the gears do not stop flashing you can manually override and jump to the next gear by pressing and releasing the switch to store the gear position quicker Repeat this through each gear When you are done come to a co
Download Pdf Manuals
Related Search