D-Link DE-809TC User's Manual
Contents
1. 5 00 0 15 mm IT 2 10 0 15 mm 5 y oe AC power adapter Plug Polarity AC Power Adapter s Plug Caution Use AC power adapter with correct AC voltage only Connecting UTP Segments This section describes the connection procedure from a UTP port of the hub to a UTP port of a station bridge router and other Ethernet devices It does not describe the connection to a 10 T hub The UTP cable extended from a UTP port is called a UTP segment and can be up to 100 meters long 8 Installation 10BASE T Ethernet Mini Hubs User s Guide Note that for Mini Hub model DE 809TP UTP port labeled 9 must be in the Normal position in order to be connectable to a station bridge or router To connect this port to a UTP port of a 10BASE T hub the port must be in the Uplink position see section Cascading Hubs Through UTP Cable in this chapter for details The button to the right of the UTP port labeled 9 is used to switch between the Normal and the Uplink position RJ 45 connector Twisted pair cable Connecting station UTP port Installation 9 Connecting Thin Coaxial Segment The BNC port on Mini Hub model DE 809TC is used to connect to athin coaxial segment Connect a T connector to the BNC connector then connect both ends of the T connector to the thin coaxial cable Ifthe thin coaxial segment terminates at the hub atta2. 11 CASCADING HUBS THROUGH UTP 12 DIAGNOSTIC LEDS amp TROUBLESHOOTING cce 14 A CABLES CONNECTORS amp AC POWER ADAPTERS 17 10BASE T UNSHIELDED TWISTED PAIR UTP 17 10 2 THIN COAXIAL CABLE 17 AC POWER ADAPTERS AAEN SE N E E SOR 18 B TECHNICAL SPECIFICATIONS ssssssssssessssesesseressesesscscees 20 10BASE T Ethernet Mini Hubs User s Guide 1 Introduction This User s Guide tells you how to install the following 10BASE T Ethernet Mini Hub models DE 809TP 9 UTP ports DE 809TC 8 UTP ports amp 1 BNC port 9 UTP ports KAR Adh Adb Ahh Ah 3 DE 809TP BNC port 8 UTP ports KAk dS JE I Js DE 809TC Port connectors on back panel of Mini Hubs Introduction The Mini Hubs are the palm size compact 10BASE T hubs that offer all the features of standard equipment rack mount 10BASE T hubs including automatic port participation collision detection diagnostic LED report and hub cascading Following is a summary of the features of the Mini Hubs 9 port hubs Each Mini Hub provides nine ports Model DE 809TP provides nine UTP ports nine RJ 45 connectors one of these ports can be used for either IOBASE T connection or cascading with another Mini Hub Model
3. tech dlink com D LINK CANADA INC 2180 Winston Park Drive Oakville Ontario L6H 5WI Canada TEL 1 905 829 5033 FAX 1 905 829 5223 WEB www dlink ca FTP ftp dlinknet com E MAIL support dlink ca E MAIL sales dlink ca D LINK DENMARK Naverland 2 DK 2600 Glostrup Copenhagen Denmark TEL 45 43 969 040 FAX 45 43 424 347 D LINK FRANCE Le FLORILEGE 2 Allee de la Fresnerie 78330 Fontenay Le Fleury France TEL 33 1 3023 8688 FAX 33 1 3023 8689 WEB www dlink france com D LINK DEUTSCHLAND GMBH 1 G Bachstrae 22 65830 Kriftel Germany TEL 49 6192 97110 FAX 49 6192 971111 WEB www dlink de BBS 49 6192 971199 INFO 0130 7250 00 toll free HELP 0130 7250 40 toll free D LINK ITALY Via Nino Bonnet n 6 20154 Milano Italy TEL 39 2 2900 0676 FAX 39 2 2900 1723 D LINK A B World Trade Center P O Box 70396 107 24 Stockholm Sweden TEL 46 8 700 6211 FAX 46 8 219 640 E MAIL info dlink se D LINK EUROPE LTD D Link House 6 Garland Road Middlesex HA7 1DP U K TEL 44 181 235 5555 FAX 44 181 235 5500 WEB www dlink com uk E MAIL D LINK MIDDLE EAST 7 Assem Ben Sabet Street Heliopolis Cairo Egypt TEL 202 245 6176 FAX 202 245 6192 WEB www dlink me com D LINK AUSTRALIA PTY LTD Unit 16 390 Eastern Valley Way Roseville NSW 2069 Australia TEL 61 2 9417 7100 FAX 61 2 9417 1077 TOLL FREE 1 80017710 WEB MAIL info dlink com au D LINK BEIJING 15th Floor Science amp Technology Tower No 11 Baishi
4. DE 809TC provides eight UTP ports eight RJ 45 connectors and one BNC port Cascading Through an Uplink switch UTP port of the DE 809TP can be used for cascading with another Mini Hub The DE 809TC provides a BNC port for cascading with other hubs without sacrificing any UTP port Backbone connection The BNC port on the DE 809TC also allows the portable Mini Hub to be attached to a coaxial backbone to be part of a larger network Installation flexibility The Mini Hub is ideal for a small size network with nine or fewer nodes Its cascading port however permits the network to expand to 32 ports or more Compact lightweight The Mini Hub s small size makes it easy to install even at installation sites with tight space It takes little space on a desktop and its light weight allows it to be easily mounted on a wall 2 Introduction 10BASE T Ethernet Mini Hubs User s Guide UTP segment UTP segment ed NUM ve TV OES anc 8 7 6 5 4 2 1 UTP segment Thin coaxial segment Ethernet segments connected to Mini Hub Introduction 3 10BASE T Ethernet Mini Hubs User s Guide 2 Installation Mounting Hub on Wall The Mini Hub can be mounted on a wall Four mounting slots
5. LIABILITY THIS LIMITATION WILL APPLY EVEN IF D LINK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE IF YOU PURCHASED A D LINK PRODUCT IN THE UNITED STATES SOME STATES DO NOT ALLOW THE LIMITATION OR EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU Limited Warranty Hardware D Link warrants its hardware products to be free from defects in workmanship and materials under normal use and service for the following periods measured from date of purchase from D Link or its Authorized Reseller Product Type Warranty Period Complete products One year Spare parts and spare kits 90 days The one year period of warranty on complete products applies on condition that the product s Registration Card is filled out and returned to a D Link office within ninety 90 days of purchase A list of D Link offices is provided at the back of this manual together with a copy of the Registration Card Failing such timely registration of purchase the warranty period shall be limited to 90 days If the product proves defective within the applicable warranty period D Link will provide repair or replacement of the product D Link shall have the sole discretion whether to repair or replace and replacement product may be new or reconditioned Replacement product shall be of equivalent or better specifications relative to the defective product but need not be identical Any product or part repai
6. UTP port uplink button Number of diagnostic LEDs 21 Power requirement DC 7 5 volts 1 Amp Power feeding through AC power adapter Operating temperature 10 to 55 Celsius Humidity 5 95 non condensing Dimensions 197 x 115 x 28 mm 7 75 x 4 53 x 1 10 inches Weight 300 10 grams AC power adapter excluded Safety UL CSA EMI FCC B CE B VCCI A C Tick BCIQ Technical Specifications 10BASE T Ethernet Mini Hubs User s Guide DE 809TC Technical Specifications 21 Standard IEEE 802 3 10BASE T Medium support thin coaxial UTP Number of UTP ports 8 Number of BNC ports 1 Number of connectors 8 RJ 45 1 BNC Number of diagnostic LEDs 20 Power requirement DC 7 5 volts 1 Amp Power feeding through AC power adapter Operating temperature 10 to 55 Celsius Humidity 5 9596 non condensing Dimensions 197 x 115 x 28 mm 7 75 x 4 53 x 1 10 inches Weight 350 10 grams AC power adapter excluded Safety UL CSA EMI FCC B CE B VCCI B C Tick BCIQ 22 Cables Connectors amp AC Power Adapters D Link Offices U S A CANADA DENMARK FRANCE GERMANY ITALY SWEDEN U K info dlink co uk EGYPT AUSTRALIA www dlink com au E CHINA INDIA JAPAN SINGAPORE TAIWAN D LINK SYSTEMS INC 58 Discovery Drive Irvine CA 92618 USA TEL 1 949 788 0805 FAX 1 949 753 7033 WEB www dlink com E MAIL
7. are provided on the bottom side of the hub for this purpose Make sure that the front panel is exposed to allow you to view the LEDs at work Installation 5 Distance 155 6 mm 6 13 in top diagram 2 Nylon screw anchors wall f i Ja 6 tapping screw No 6 tapping screw Nylon screw anchors Distance 70 5 mm 2 74 in bottom diagram 6 Installation 10BASE T Ethernet Mini Hubs User s Guide Connecting AC Power Adapter The Mini Hub uses an external AC power adapter There is no power switch The hub is powered on once the AC power adapter is connected to an AC power source and the hub s AC power socket Caution Installation To prevent damage to your hub before you begin using the AC power adapter double check its input AC voltage The AC power adapter s input voltage must conform to its AC power source s voltage Appendix A lists the specifications of the AC power adapters applicable to Mini Hubs and to different countries If you use an AC power adapter supplied by yourself and your country is not listed in the appendix check with your networking products dealer to make sure that you use a proper AC power adapter Socket
8. excessive packet collisions 4 a disconnected point somewhere along the entire thin coaxial cable length or 5 unterminated segment Check all connectors along the cable length If segment is not terminated terminate both ends with 50 ohm terminators OFF 1 Cable is connected and 2 segment has no problem Uplink 0 ON The 9 UTP port is in the Uplink position cross wired 0 OFF The 9 UTP port is in the Normal position straight through wires 16 Installation 10BASE T Ethernet Mini Hubs User s Guide A Cables Connectors amp AC Power Adapters 10BASE T Unshielded Twisted Pair UTP Cable Cable characteristics 0 4 0 6 mm 22 26 AWG 8 wire only 4 wires used for IOBASE T Maximum segment length 100 meters Applicable connectors RJ 45 Telco 50 10BASE2 Thin Coaxial Cable Cable characteristics 0 2 inch diameter RG 58A U 50 ohm Maximum segment length 185 meters Minimum distance between two nodes 0 5 meter Maximum number of nodes per segment 30 Cables Connectors amp AC Power Adapters 17 AC Power Adapters The following lists the specifications of the AC power adapters supplied by D Link for use with the Mini Hub Your Mini Hub package may contain one of these AC power adapters If you use an AC power adapter supplied by yourself make sure that it complies with the output power listed below and the input power and plug AC power specifications o
9. to dispense with the trouble of crossing the UTP cable s wires Putting this port in the Uplink position can be done by pressing down the button located next to the port Note Never cause a loop when you cascade hubs since this might cause unpredictable results 12 Installation 10BASE T Ethernet Mini Hubs User s Guide Press button down Port Uplink position KAR Adh JG IE Ju JE DE 809TP NIMM DE 809TC Hub cascading If straight through UTP cable is used one UTP port must be in Uplink position Installation 13 Diagnostic LEDs amp Troubleshooting Power 0 ON power good 0 OFF power bad Check to see if the AC power adapter is properly connected or if the correct AC power adapter is being used DE 809TP Power Link Rx lt Collision CO Partition 1 TP2 4 TP5 TP TP7 8 TPO Uplink Power Link R CO CO C E Rx Collision C Partition C C O O CO C Partition TP2 TPA TPS TP amp TP7 BNC 14 Installation 10BASE T Ethernet Mini Hubs User s Guide DE 809TC Diagnostic LEDs on front panel of Mini Hubs Collision o Blinking Packet collision is occurring Packet collisions are not an abnormal situation Collisions occur when two o
10. D Link 10BASE T Ethernet Mini Hubs Models DE 809TP DE 809TC User s Guide Fifth Edition Jan 1999 6DE809TP 05 Printed In Taiwa RECYCLABLE WARRANTIES EXCLUSIVE IF THE D LINK PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE THE CUSTOMER S SOLE REMEDY SHALL BE AT D LINK S OPTION REPAIR OR REPLACEMENT THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR OTHERWISE INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE D LINK NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE OR USE OF D LINK S PRODUCTS D LINK SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY THE CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO REPAIR OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING OR OTHER HAZARD LIMITATION OF LIABILITY IN NO EVENT WILL D LINK BE LIABLE FOR ANY DAMAGES INCLUDING LOSS OF DATA LOSS OF PROFITS COST OF COVER OR OTHER INCIDENTAL CONSEQUENTIAL OR INDIRECT DAMAGES ARISING OUT THE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTERRUPTION OF A D LINK PRODUCT HOWEVER CAUSED AND ON ANY THEORY OF
11. ch a 50 ohm terminator to one end of the T connector 50 ohm terminator em ID AI T connector Thin coaxial segment Ethernet segments connected to Mini Hub 10 Installation 10BASE T Ethernet Mini Hubs User s Guide Cascading Hubs Through Thin Coaxial Cable The BNC port on the Mini Hub model DE 809TC can be used to cascade hubs together You may cascade DE 809TC hubs together through the BNC ports You may also cascade the DE 809TC with any other IEEE 802 3 Ethernet standard 10BASE T hubs equipped with BNC ports You may attach up to thirty nodes to a thin coaxial segment In this sense it is possible to cascade a maximum of thirty hubs together through the thin coaxial cable Be sure to leave a minimum of 0 5 meter 2 feet of cable between two BNC ports Installation 11 Cascading Hubs Through UTP Cable Any ofthe UTP ports can be used to cascade hubs together Note that when two UTP ports of two hubs are connected together the wires inside the UTP cable must be crossed over See appendix A for the wire cross over Mark all crossed over UTP cables clearly so they will not be used by mistake for normal connection If you use Mini Hub model DE 809TP UTP port labeled 9 is especially designed for hub cascading When this port is in the Uplink position its signal reception and transmission are reversed This allows you
12. er Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with emission limits Changes or modifications not expressly approved by user s authority to operate this equipment vi VCCI I Warning For Model DE 809TP ER DEREN FABRE VCC e WARE CT OBER A ERE T 3 5b ES A Ed SABRES VCCI II Warning For Model DE 809TC CORBY AE RS VCCI O AECA SEHEN ER CT CORE TAIEZHNELTCEIN 0SBNoDdTL ave PRESARIO vid TAIWANESE BCIQ A Warning SERNA hee cta uae drj ERE EHE n TRE GENE a IDEE fehlen MEA 8 rare vii Table of Contents T INTRODUCTION Gio 1 2 INSTALLATION 5 MOUNTING ON WALL occcccnnnnnncccncnnnnnnnnnoccncnnnnnnnaninicocnnonononos 5 CONNECTING AC POWER ADAPTER occccccnnnnnniocccccnnnnnnanicococnnononanos 7 CONNECTING UTP SEGMENTS cccccsssseecccccsseeesseececssseeeeeseseess 8 CONNECTING THIN COAXIAL SEGMENT ccccccsssesecccssseeeeeeseseees 10 CASCADING HUBS THROUGH THIN COAXIAL
13. f your area AC power adapter model AD 071A Input power AC 120 volts 50 60Hz Output power DC 7 5 volts unregulated 1 A Maximum power consumption 7 5 watts Plug North American standards Safety standards UL CSA 14141 power adapter model AD 071AD Input power AC 240 volts 50 60Hz Output power DC 7 5 volts unregulated 1 A Maximum power consumption 7 5 watts Plug U K standard Safety standard BSI 14141 power adapter model AD 071AB gt Input power AC 220 volts 50 60Hz gt Output power DC 7 5 volts unregulated 1 A gt Maximum power consumption 7 5 watts 18 Cables Connectors amp AC Power Adapters 10BASE T Ethernet Mini Hubs User s Guide gt Plug German standard gt Safety standard VDE AC Power adapter model AD 071AJ gt Input power AC 100 volts 50 60Hz Output power DC 7 5 volts unregulated 1 A Maximum power consumption 7 5 watts gt gt gt Safety standard Japan T mark 5 00 0 15 mm 2 10 0 15 mm e e e 12 00 0 5 mm Plug Polarity AC Power Adapter s Plug AD 071AJ Plug AD 071A Plug AD 071AB Plug AD 071AD Plug Cables Connectors amp AC Power Adapters 19 B Technical Specifications DE 809TP 9999 999999 9 20 Standard IEEE 802 3 10BASE T Medium support UTP Number of UTP ports 9 Number of connectors 9 RJ 45 Cascading Switchable straight through cross wired
14. its are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this user s guide may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Class B for Model DE 809TC FCC ID No KA2HPCO9TC1 This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with this user s guide may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiv
15. qiao Road Haidian District Beijing 100081 China TEL 86 10 68467106 9 FAX 86 10 68467110 WEB www dlink co cn D LINK INDIA PVT LTD Bombay Office Plot No 5 Kurla Bandra Complex Rd Off Cst Rd Santacruz E Bombay 400 098 India TEL 91 22 6172478 FAX 91 22 6172476 D LINK TOKYO 10F 8 8 15 Nishigotanda Shinagawa ku Tokyo 141 Japan TEL 81 3 5434 9678 FAX 81 3 5434 9868 WEB www d link co jp D LINK SINGAPORE PTE LTD 1 International Business Park 03 12 The Synergy Singapore 609917 TEL 65 774 6233 FAX 65 774 6322 BBS 65 774 4787 E MAIL info dlink com sg D LINK TAIWAN 2F No 233 2 Pao Chiao Rd Hsin Tien Taipei Taiwan R O C TEL 886 2 2916 1600 FAX 886 2 2914 6299 WEB www dlink com tw Registration Card Print type or use block letters Your name Mr Ms Organization Dept Your title at organization Telephone Fax Organization s full address Country Date of purchase Month Day Year Product Model Product Serial No Product installed in type of Product installed in Prendes come i e g Compaq 486 I eter serial No Applies to adapters only Product was purchased from Reseller s name Telephone Fax Reseller s full address Answers to the following questions help us to support your product 1 Where and how will the product primarily be used OTravel Business Bu
16. r more computers transmit packets on the network simultaneously and a contention takes place on the network line The computers should then back off then retry transmission This trial and error process is repeated until no collision takes place Note Excessive collisions may result when multiple hubs are cascaded through a thin coaxial segment and many stations are connected on the network 0 No packet collision Link Rx for each UTP port ON Data link between 1 Mini Hub s UTP port and 2 node s or cascaded hub s UTP port is successful OFF 1 No data link or 2 cable disconnected Check for bad cable or loose connectors For cascaded hubs check to see if UTP cable contains crossed over wires Also check for a power good condition at both ends of the connection If you suspect that the hub port is damaged contact your authorized dealer for service o Blinking Packet reception is occurring Installation 15 Rx for BNC port o Blinking Packet reception is occurring 0 OFF No packet reception Partition for each UTP port 0 ON The UTP port is being partitioned off due to excessive packet collisions Note that the UTP cable between a hub port and a non repeater node must contain straight through wires no cross over 0 OFF Segment has no problem Partition for BNC port 0 ON The BNC port is being partitioned off due to 1 no cable is connected 2 faulty cable or connectors 3
17. red by D Link pursuant to this warranty shall have a warranty period of not less than 90 days from date of such repair irrespective of any earlier expiration of original warranty period When D Link provides replacement then the defective product becomes the property of D Link Warranty service may be obtained by contacting a D Link office within the applicable warranty period and requesting a Return Material Authorization RMA number Ifa Registration Card for the product in question has not been returned to D Link then a proof of purchase such as a copy of the dated purchase invoice must be provided If Purchaser s circumstances require special handling of warranty correction then at the time of requesting RMA number Purchaser may also propose special procedure as may be suitable to the case After an RMA number is issued the defective product must be packaged securely in the original or other suitable shipping package to ensure that it will not be damaged in transit and the RMA number must be prominently marked on the outside of the package The package must be mailed or otherwise shipped to D Link with all costs of mailing shipping insurance prepaid D Link will ordinarily reimburse Purchaser for mailing shipping insurance expenses incurred for return of defective product in accordance with this warranty D Link shall never be responsible for any software firmware information or memory data of Purchaser contained in stored on or in
18. siness Use 2 How many employees work at installation site 01 employee 02 9 0110 49 150 99 1100 499 0500 999 11000 or more 3 What network protocol s does your organization use OXNS IPX OTCP IP ODECnet OOther 4 What network operating system s does your organization use OD Link LANsmart Novell NetWare OINetWare Lite OSCO Unix Xenix OPC NFS 3 OBanyan Vines ODECnet Pathwork OWindows NT Windows NTAS OWindows 95 OOther 5 What network management program does your organization use OD View OpenView Windows OHP OpenView Unix OSunNet Manager LINovell NMS ONetView 6000 Other 6 What network medium media does your organization use OFiber optics OThick coax Ethernet Thin coax Ethernet 010BASE T UTP STP O100BASE TX 01100BASE T4 01100VGAnyLAN OOther 7 What applications are used on your network ODesktop publishing OSpreadsheet DWord processing LICAD CAM ODatabase management LlAccounting HOther 8 What category best describes your company LlAerospace LIEngineering OFinance OHospital OLegal Estate OManufacturing ORetail Chainstore Wholesale OVAR System house company OGovernment Transportation Utilities Communication DlOther 9 Would you recommend your D Link product to a friend OYes ONo ODon t know yet
19. tegrated with any product returned to D Link pursuant to this warranty Any package returned to D Link without an RMA number will be rejected and shipped back to Purchaser at Purchaser s expense and D Link reserves the right in such a case to levy a reasonable handling charge in addition mailing or shipping costs D Link Offices for Registration and Warranty Service The product s Registration Card provided at the back of this manual must be sent to a D Link office To obtain an RMA number for warranty service as to a hardware product or to obtain warranty service as to a software product contact the D Link office nearest you An addresses telephone fax list of D Link offices is provided in the back of this manual Trademarks Copyright 1999 D Link Corporation Contents subject to change without prior notice D Link is a registered trademark of D Link Corporation D Link Systems Inc All other trademarks belong to their respective proprietors Copyright Statement No part of this publication may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from D Link Corporation D Link Systems Inc as stipulated by the United States Copyright Act of 1976 FCC Warning Class A for Model DE 809TP This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These lim
Download Pdf Manuals
Related Search