Cub Cadet 19A70001000 Operator's Manual
Contents
1. Figure 3 3 Upper Hole Figure 3 4 Attaching Grass Bags amp Grass Bag Cover 1 Place the support tube in position on the rear of unit by sliding the support tube down through the holes in the left side of the bracket assembly Use the inside hole on the bracket assembly Refer to Figure 4 1 Attachi ng 2 Attach the grass bags by hooking them onto the grass bag bracket using the slots in the grass bag and the G rass Bags tabs on the grass bag bracket as shown in Figure 4 2 amp G rass Bag 3 Remove the clevis pins belleville washers and hairpin clips from the hinge brackets on the grass bag Cover cover 4 Place the grass bag cover on top of the grass bags and align the holes on the hinges of the grass bag cover with the corresponding holes on the support Figure 4 1 tube assembly See Figure 4 3 5 Insert the clevis pin through the hinge on the support tube assembly and then through the grass bag cover See Figure 4 4 6 Secure with belleville washer and hairpin clip with the NOTE crown side of the washer going against the hairpin Insert the clevis pins clip See inset images in Figure 4 4 from the outside in as 7 Repeat with the second set of hardware through the shown in the inset second hinge of the grass bag and the tube assembly images of Figure 4 4 from the opposite direction NOTE It is very important to NOTE Insert the clevis pins from the outside2. find the nearest Cub Cadet service dealer in your area CONTENTS OF CARTON Before beginning installation remove all parts from the carton to make sure everything is present Carton contents are listed below and shown in Figure 2 1 One Chute Tube One Discharge Chute Assembly Two Grass Bag Assemblies One Support Tube One Grass Catcher Cover Assembly Chute Tube S Grass Bag Cover Assembly Grass Bag Assemblies Two Mounting Brackets One Cross Support Bracket Two Bracket Supports One Catcher Support Discharge Chute Assembly Bracket Support Catcher Support CA Cor Mounting Bracket Cross Support Bracket Figure 2 1 CONTENTS OF HARDWARE PACK This grass collector kit is shipped with a hardware pack enclosed Please check your hardware pack against the illustration below Carton Contents Group A Assembling and Attaching Mounting Bracket f Co 2 x lt w fo Clevis Pin 1 5 16 18 x 750 6 If you are missing any parts call the Cus tomer Dealer Referral Line at 1 877 282 8684 or visit www cubcadet com to find the nearest Cub Cadet service dealer in your area 0 oy QZ Hairpin Clip 1 g k E O 2 zZ E on o ee o gt a O Hex Bolt 1 4 20 x 620 8 Flange Lock Nut 1 4 20 8 Figure 2 2 Assembling and Attaching Mounting Bracket IMPORTANT Before assembl
3. in as shown in the inset images of Figure 4 4 It is very important to maintain this order and direction while installing these hardware pieces After installation make sure that the grass bag cover pivots on the support tube and opens maintain this order and direction while installing these hardware pieces After installation make sure that the grass bag cover pivots on the sup port tube and opens Figure 4 3 Figure 4 4 Attaching Discharge Chute 1 Lower the deck to its lowest position 2 Raise the chute deflector on the deck A and hold it while you position the discharge chute over the chute opening See Fig 5 1 Attach i ng 3 Insert the pin B on the discharge chute into the hole Di h on the deck as indicated by the arrow in Fig 5 1 ISC arge 4 Push down on the discharge chute so that it covers Ch ute the opening of the deck completely 5 Lock the discharge chute in position by stretching the amp retainer strap over the front deck wheel bracket and hooking onto the bottom of the bracket as seen in the Bagger inset D in Fig 5 1 6 Insert the curved end of chute tube into the hole in the grass bag cover See Fig 5 2 Usage Figure 5 1 7 Place the lower end of the chute tube over the discharge chute so that the tabs on the discharge chute fits into the pockets on the chute tube See Fig 5 3 8 Secure by hooking the two retainer straps of the discharge chute to the
4. pins on the chute tube See Fig 5 3 Bagger Usage NOTE When both grass bags are full place the tractor ona firm level surface disengage the PTO turn the tractor engine off and set the parking brake 1 Flip Seat up 2 Lift up grass bag cover Do not remove the chute tube assembly from the tractor 3 Remove the grass bags by lifting these up and mov ing the bags away from the support tube assembly 4 Empty the grass clippings at a proper disposal sight Figure 5 2 use the handle at the bottom of each grass bag Holding the bag firmly empty the contents 5 Replace grass bags close lid flip down seat restart your tractor and resume cutting your grass Figure 5 3 NOTES Use this page to take notes and write down important information 10 REF PART DESCRIPTION NO NUMBER z 7 11 12 3 14 8 7 731 0899E Catcher Tube 20 736 3092 Flat Washer 21 2 2 25 26 710 0604A Self Tapping Screw 5 16 18 Ro aS 710 3008 Hex Screw 5 16 18 x 0 75 ine 2 712 04064 Flange Lock Nut 1 4 20 27 712 0272 Hex Sems Nut 10 24 ao ao ao Pp 3 Po Illustrated Parts List wa K ORY OPS To order replacement parts call the Customer Dealer Referral Line at 1 877 282 8684 or visit www cubcadet com to find the nearest Cub Cadet service dealer in your area CUB CADET LLC MANUFACTURER S LIMI
5. Manual furnished with the product and has not been subject to misuse abuse neglect accident improper maintenance alteration vandalism theft fire water or damage because of other peril or natural disaster Damage resulting from the installation or use of any part accessory or attachment not approved by Cub Cadet for use with the product s covered by this manual will void your warranty as to any resulting damage In addition Cub Cadet may deny warranty coverage if the hour meter or any part thereof is altered modified disconnected or otherwise tampered with HOW TO OBTAIN SERVICE Warranty service is available WITH PROOF OF PURCHASE AND APPLICABLE MAINTENANCE RECORDS through your local authorized service dealer To locate the dealer in your area In the U S A Check your Yellow Pages or contact Cub Cadet LLC at P O Box 361131 Cleveland Ohio 44136 0019 call 1 877 282 8684 or log on to our website at www cubcadet com In Canada Contact MTD Products Limited Kitchener ON N2G 4J1 call 1 800 668 1238 or log on to our website at www mtdcanada com Without limiting the foregoing this limited warranty does not provide coverage in the following cases a Routine maintenance items such as lubricants filters blade sharpening tune ups brake adjustments clutch adjustments deck adjustments and normal deterioration of the exterior finish due to use or exposure b Service completed by someone other than an authorize
6. TED WARRANTY FOR SEPARATELY SOLD ATTACHMENTS AND ACCESSORIES IMPORTANT To obtain warranty coverage owner may be required to present an original proof of purchase and applicable maintenance records to the servicing dealer Please see the operator s manual for information on required maintenance and service intervals The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased or leased and used in the United States and or its territories and possessions and by MTD Products Limited with respect to new merchandise purchased or leased and used in Canada and or its territories and possessions either entity respectively Cub Cadet Cub Cadet warrants this product excluding its Normal Wear Parts as described below against defects in material and workmanship for a period of three 2 years commencing on the date of original retail purchase or lease and will at its option repair or replace free of charge any part found to be defective in materials or workmanship Normal Wear Parts are warranted to be free from defects in material and workmanship for a period of thirty 30 days from the date of original purchase or lease Normal wear parts include but are not limited to items such as belts blades blade adapters grass bags rider deck wheels seats and tires This limited warranty shall only apply if this product has been operated and maintained in accordance with the Operator s
7. To The Owner Carton Contents Assembly Parts Lists e Warranty OPERATOR S MANUAL Cub Cadel Twin Rear Bagger Kit For i1000 Series Lawn Tractors with a 42 Timed Deck Model 19470001000 IMPORTANT READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION FORM NO 769 03805A PRINTED IN U S A CUB CADET LLC P O BOX 361131 CLEVELAND OHIO 44136 0019 4 10 2008 This Operator s Manual is an important part of your new grass collector It will help you assemble prepare and maintain the unit for best performance Please read and understand what it says Finding and Recording Model Number BEFORE YOU START ASSEMBLING YOUR NEW EQUIPMENT please locate the model plate and copy the information from it in this Operator s Manual for future reference The information on the model plate is very important if you need help from our Customer Support Department or your authorized dealer You can locate it by looking on the front left portion of the plastic grass catcher cover as seen below Model Number Serial Number b CUB CADET LLC Cu Cadet P O BOX 361131 www cubcadet com CLEVELAND OH 44136 DEALER LOCATOR PHONE NUMBER 877 282 8684 Locate the model plate on your bagger and copy the information from it in the space provided above for future reference Customer Support Please do NOT return the unit to the retailer from which it was purchased without first contacting Customer Support If you ha
8. d service dealer c Cub Cadet does not extend any warranty for products sold or exported outside of the United States and or Canada and their respective possessions and territories except those sold through Cub Cadet s authorized channels of export distribution d Replacement parts and or accessories that are not genuine Cub Cadet parts e Transportation charges and service calls f Commercial or Institutional Use There are no implied warranties including without limitation any implied warranty of merchantability or fitness for a particular purpose No warranties shall apply after the applicable period of express written warranty above No other express warranties beyond those mentioned above given by any person or entity including a dealer or retailer with respect to any product shall bind Cub Cadet The exclusive remedy is repair or replacement of the product as set forth above The terms of this warranty provide the sole and exclusive remedy arising from the sale and or lease of the products covered hereby Cub Cadet shall not be liable for any incidental or consequential loss or damage including without limitation expenses incurred for substitute or replacement lawn care services or for rental expenses to temporarily replace a warranted product Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above exclusions
9. or limitations may not apply to you In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold Alteration of safety features of the product shall void this warranty You assume the risk and liability for loss damage or injury to you and your property and or to others and their property arising out of the misuse or inability to use the product This limited warranty shall not extend to anyone other than the original purchaser or to the person for whom it was purchased as a gift HOW LOCAL LAWS RELATE TO THIS WARRANTY This limited warranty gives you specific legal rights and you may also have other rights that vary in different jurisdictions Cub Cadet LLC P O BOX 361131 CLEVELAND OHIO 44136 0019 Phone 1 877 282 8684 MTD Products Limited Kitchener ON N2G 4J1 Phone 1 800 668 1238 GDOC 100177 REV A
10. ve difficulty assembling this product or have any questions regarding the controls operation or maintenance of this unit you can seek help from the experts Choose from the options below e Visit www cubcadet com for many useful suggestions Click on the Customer Service link and you will get several options to help in answering your questions Click on the appropriate button and help is immediately available e Phone our Customer Dealer Referral Line to find a dealer nearest you at 1 877 282 8684 To The Owner The Model 19470001000 Twin Bag Grass Collector is a grass collection NOTE References to LEFT and RIGHT indicate the left and right sides system specifically designed for use on Cub Cadet l 1000 Series lawn of the tractor when facing forward in the operator s position Reference tractors equipped with a 42 inch timed mowing deck to the FRONT indicates the grille end to the REAR the rear end of the tractor Carefully read all sections and study the illustrations to ensure proper in stallation and usage of this attachment Read and observe all WARNING and CAUTION statements They are included to provide for the protection of the equipment installer and user and to ensure the prolonged service life of the equipment NOTES Use this page to make notes and write down important information Carton Contents If you are missing any parts call the Customer Dealer Referral Line at 1 877 282 8684 or visit www cubcadet com to
11. y place the tractor on a firm level surface disengage the PTO stop the tractor engine and set the park ing brake NOTE There are two holes in the clevis pin Be sure to insert the hairpin clip in the upper hole to properly secure the bracket assembly to the hitch plate Assembling and Attaching The Bracket Assembly Hardware Group A IMPORTANT Before assembly place the tractor on a firm level surface disengage the PTO stop the tractor engine and set the parking brake 1 Assemble the mounting bracket assembly as shown in Figure 3 1 NOTE The mounting bracket assembly may have been preassembled at the factory if this is the case skip Step 1 and proceed to Step 2 2 For convenience pivot the seat forward and leave it in that position until the grass collector is fully mounted and assembled 3 Position the bracket assembly to the outside of the hitch plate See Figure 3 2 4 Push the hooked ends of the bracket assembly in A and under the shoulder bolts B and swing in the bottom down over the hitch plate aligning with the hole on the hitch plate C See Figure 3 3 5 Insert the clevis pin through the aligned holes in both the bracket assembly and the hitch plate and secure with the hairpin clip Refer to Figure 3 4 NOTE There are two holes in the clevis pin Be sure to insert the hairpin clip in the upper hole to properly secure the bracket assembly to the hitch plate Figure 3 1
Download Pdf Manuals
Related Search