Crimestopper Security Products EZ-45DP User's Manual
Contents
1. Parking Lights will start flashing and doors will unlock 3 Turn Ignition switch OFF remove key and exit the vehicle Engine should remain running 4 The vehicle s parking lights will flash for the programmed run time of 12 24 or 36 or 48 minutes and then switch to solid while motor runs indefinitely or until fuel Supply runs out SELECTABLE HOURLY COLD START MODE 1 4 HOURS This mode allows the vehicle to be programmed to self start every 1 2 3 or 4 hours and run for the programmed run time This can be helpful during extremely cold conditions where engine fluid freeze up is a concern THE VEHICLE MUST BE OUTDOORS OR IN A WELL VENILATED AREA Once this mode is set the unit will start at the programmed hourly interval and run for the programmed run time To reset this mode start the vehicle with the key or the remote control SELECTABLE HOURLY COLD START MODE EXITING THE VEHICLE 1 Engine should be running with the Key Press the Remote Start button for at least 1 second Lights will turn on signaling the remote start has turned on and doors will unlock 2 Within 10 seconds press and release the valet program button once for each hourly increment 1 time 1hour 2X 2 hours 3X every 3 hours 4X every 4 hours 3 Parking Lights will turn once the button is pressed and flash for each consecutive button press 4 Turn Ignition switch OFF remove key and exit the vehicle Engine should remain running 5 Once outside th2. E RESPONSIBILITY TO A Understand the operation of this system and its safety features B Check for proper operation of the system prior to accepting delivery of the vehicle from the installation facility C Check and maintain the condition of the vehicle and all items relative to the proper operation of this system and its safety features D Always leave the doors and windows closed and locked to protect against accident and theft DO NOT remote start the vehicle in a closed garage Make sure that the garage door is open or there is adequate ventilation Failure to observe this rule could result in injury or death from poisonous Carbon Monoxide fumes REMOTE OPERATION OPERATION BUTTON 1 Lock Symbol e Press and release to Lock doors e Press and Hold for more than 3 seconds to activate 4B Panic feature BUTTON 2 Unlock Symbol TRUNK e Press and release to Unlock doors For EZ 55DP Il only Driver Door Priority Unlock e Press 2 times for Driver Door Priority Unlock 1 1D BUTTON 3 Trunk Symbol LOCK UNLOCK e Press and Hold for 1 2 second or press twice to activate trunk pop A UX 2 A UX 3 BUTTON 4 Start e Press and Hold for 2second or press twice to HA 45 Start Stop Engine EZEE START a ea REMOTE _ J BUTTON 5 Vehicle 2 2 Function STARTER 2ND VEHICLE AUX 2 Press button 5 then press button 1 AUX 4 s 2ND FUNCTION Press and Hold for 2 sec for vehicle 2 For
3. E2Z 45DP EZ 55DP DP SERIES II DATA PORT 1 Way Paging Remote Engine Starting amp Keyless Entry System with 5 Button Sidekick Remote Control OPERATING INSTRUCTIONS PRIMARY These are features that must be connected in order for the system to operate properly i e Remote Start connections Flashing lights Brake Reset For programming the hood pin and program button are required OPTIONAL These are features are to be connected only if desired or agreed upon by the customer and the installing dealer i e Door Locks Trunk Pop Dome Light Illumination Horn Honk Anti Grind etc These features may also require additional parts and or labor fees Consult with your installer beforehand to be sure of what is going to be installed with your particular system TECHNICAL SUPPORT 800 998 6880 This device complies with FCC Rules part 15 Operation is Monday Friday 8 00am 4 30pm Pacific Std Time subject to the following two conditions 1 This device may not Web Site www crimestopper com cause interference and 2 this device must accept any E mail email crimestopper com interference that may be received including interference that may cause undesired operation The manufacturer is not responsible for any radio or TV interference caused by CRIMESTOPPER SECURITY PRODUCTS INC unauthorized modification to this equipment Such 1770 S TAPO STREET SIMI VALLEY CA 93063 modification could void the user s authority to operate t
4. EZ 55DP Il only AUX3 AUX4 AUX 3 Press button 5 then press button 2 AUX 4 Press button 5 then press button 4 The transmitter supplied with the EZ 45DP II 55DP II system has five buttons The button configuration of the EZ 45DP 55DP Il is Factory set and unchangeable See Page 12 for additional information on how to use your remote to operate a second vehicle equipped with a EZEE START system NOTE BUTTON 4 and 3 Remote Start Trunk There is a deliberate delay or 2 presses Optional built into the system on button 4 and 8 to help prevent accidental remote starting from the remote being in your pocket or purse During normal use if you press button 4 or 3 too quickly the system may not start the engine or open trunk 3 REMOTE ENGINE STARTING REMOTE ENGINE STARTING SUCCESSFUL START 1 Press the remote start button for at least 1 2 second Default or twice if set for double press 2 Parking lights flash once return solid and the Ignition Acc circuits turn on 3 After a few seconds the Starter Motor engages Parking lights and Acc circuits will turn off while cranking 4 Engine Starts and Runs Parking Lights and Acc turn back on Doors Lock 5 Engine will remain running for programmed run time until reset with Brake pedal If needed the engine can be turned off with remote transmitter by pressing and releasing or double press the Start button FLASH 1X AFTER Se on ppm Ga Ca ee l SEC STARTER T
5. F the system will not automatically lock or unlock the vehicle See your installer for programming information on this feature DOOR LOCK NOTE If your system has been setup with an optional starter kill relay but you do not have power door locks note the following The lock and unlock buttons on the remote contro must still be utilized to operate the Starter disable REMOTE PANIC Used only with Optional HORN HONK feature installation For personal safety this unit now includes a panic feature To sound the vehicle car horn press the Lock Button on the remote for more than 2 seconds The vehicle horn will honk along with flashing parking lamps for 1 minute Reset Remote Panic by pressing either the lock or unlock button See next section for Horn Honk information HORN CHIRP HONK OUTPUT Optional with Horn connection amp programming This feature if installed will provide audible confirmation chirps from the factory horn for lock and unlock When using this feature pressing the Lock Unlock button a 2 time within 3 7 seconds or single press lock unlock will provide a horn chirp for audible confirmation The system can also be programmed to provide 3 chirps when a remote start is requested using the remote Note Horn honk chirp feature may require extra labor and or parts to install REMOTE TRUNK RELEASE OR DOMELIGHT ILLUMINATION Optional This EZEESTART system includes an output that can be programmed to remotely release a factory electron
6. HEN C5 REMOTE ENGINE STARTING UNSUCCESSFUL START In the event that the engine does not start on the first attempt the system shuts down for a few seconds and then attempts to restart the engine a 2 and 3 time For hard starting engines the unit will allow a starter crank time of up to 10 seconds maximum This should provide ample cranking time for difficult starts but is limited to 13 seconds to help prevent damage to the starter from over cranking 1 If engine starts on 2 or 3 attempt see steps 4 amp 5 above of Successful Start 2 If Third attempt fails to start engine the system will turn off and doors will remain locked NO FURTHER ATTEMPTS WILL BE MADE AUTOMATICALLY SOLID TURNING OFF A REMOTE STARTED ENGINE 1 Engine is running in Remote Start Parking lights ON 2 Press and release the remote start button 3 Engine amp parking lights OFF Doors re lock re arm REMOTE ENGINE STARTING Cont ENTERING YOUR REMOTE STARTED VEHICLE 1 With engine running Remote Unlock system If equipped or open door with key 2 Enter vehicle and be careful not to step on brake pedal Remote Start Reset 3 Turn Ignition to ON RUN position then press brake pedal to reset the Remote Starter amp Shift out of park 4 Remote starter will reset instantly when the brake is pressed Parking lights will turn off and the ignition key is now controlling you
7. P General Motors cars trucks require a secondary ignition circuit for the Transmission computer and other on board systems If the vehicle is started without this wire energized there may be a Check Engine or Service Engine Soon light on the dash This may cause damage if the vehicle is driven in this condition Check with installer to see if this circuit is present and has been properly connected to the system 2 In some cases commonly Nissan vehicles an additional Start Cranking circuit is required for the vehicle to run properly The EZEE START system includes a wire that can be used for this Starter 2 circuit Check with your installer for details 13 REMOTE START DIAGNOSTICS If the system flashes the parking lights one to three times and doesn t attempt remote it means the following 1 Parking Light Flash Problem with Brake Switch 2 Parking Light Flashes Problem with Hood Switch 3 Parking Light Flashes Valet Service Mode BATTERY REPLACEMENT To replace the battery Simply remove the screws on back of the transmitter and open the case Remove the battery and replace The replacement battery for all transmitters is GP23A GRIME we z aaz www crimestopper com email crimestopper com 2006 Crimestopper Security Products ONLINE TECHNICAL SUPPORT http www crimestopper com
8. dule 2 Check Antenna Module connection The antenna module included with this system must be plugged in 3 Transmitters may need to be programmed to the unit See transmitter programming steps on Page 11 4 Check transmitter Batteries and replace if necessary UNIT CRANKS VEHICLE BUT ENGINE NEVER STARTS 2 parts 1 In extreme cold or severe weather conditions the unit may take more than the first attempt to start the vehicle The remote start unit will make up to 3 attempts to start the engine 2 In some vehicles there may be a Factory anti theft system that will not allow the engine to run without the key in the ignition These systems may include Factory Security Modules GM Passkey Passlock and RF Transponder systems Ford P A T S Many late 1990 s through 2006 vehicles include some type of Anti Theft system which may require a bypass module Check with your installer to make sure that the bypass device if equipped is functioning properly SYSTEM IS UNSUCCESSFUL AT REMOTE START DURING EXTREME COLD CONDITIONS Please be aware that during sub freezing conditions your remote starter may take more that one attempt to start or it may not successfully start the vehicle after 3 attempts During these conditions the vehicle may not properly start even using the key therefore trying to start by the remote would also be unsuccessful VEHICLE STARTS BUT CHECK ENGINE LIGHT COMES ON OR ENGINE RUNS BADLY 2 parts 1 Many 1995 U
9. e vehicle press and release the remote start button to turn off engine The parking lights will flash the number of times indicating the hourly increment for confirmation 6 The vehicle will start by itself at the selected hourly increment until driven with key or started via the remote control Programmable for second press or double press This option is selectable by your installer TURBO TIMER MODE OPTIONAL The optional Turbo Timer mode allows the EZEE START system to keep a Turbo or Turbo Diesel vehicle running for 1 to 5 minutes selectively after you remove the key exit the vehicle and lock the doors remotely This is handy for turbo cool down without the need for expensive turbo timers This mode requires the use of an extra part called a momentary switch button that is not included with the kit Check with your installer about adding this feature NOTE The turbo timer button will also trigger a remote start if it is inadvertently pressed when the vehicle is not running Please note this when installing the button and choose a location out of harm s way 1 Engine should be running with the key 2 Press and hold down the brake pedal 3 Press your Turbo Timer button 1 to 5 times for each minute of run time you desire 1 press 1 min 4 As you release the brake pedal and your system will confirm by flashing the lights the same number of times the button was pressed 5 Turn Ignition switch OFF remove key and
10. ehicle Programming and Operation instruction In step 4 of transmitter programming see page 11 press and hold middle button 5 for 2 sec then press the lock button parking light will flash indicating the remote is programming Operation Press vehicle 2 button middle button for 2 sec and within 3 seconds press any of the 4 function buttons on your remote You can keep pressing function buttons to control car 2 as long as it is within the 3 second window After 3 seconds have elapsed the remote will revert back to Car 1 operation TROUBLESHOOTING BEFORE YOU CALL SECTION UNIT WILL NOT ATTEMPT A START KEYLESS ENTRY STILL FUNCTIONS NORMALLY The unit is in Valet mode Turn Ignition ON press and hold valet programming button for 6 seconds then turn key off Unit is now out of valet mode and should perform a remote start If optional LED indicator is installed then it will be on solid when in Valet and OFF when out of Valet UNIT FLASHES LIGHTS ONCE AND WILL NOT ATTEMPT A START The unit senses a fault at the Brake Purple wire is active or the Hood is OPEN Blue wire grounded This is a safety feature of the unit Check installation for faults and make sure hood is closed and latched and brake wire is not active Make sure hood is in good condition and is depressed when hood is closed 12 TROUBLESHOOTING cont NO RESPONSE FROM REMOTE TRANSMITTERS 4 Parts 1 Check for proper power ground wiring connections at mo
11. exit the vehicle Remote lock your doors for safety The engine should remain running for the selected number of minutes PRESS TURBO RELEAG RUNNING PRESS TIMER BUTTON AND HOLD 1 5 TIMES BRAKE BRAKE p Eva gt 0 gt a aioe REMOVE KEY REMAIN RUNNING EXIT VEH 1 5 MIN CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY POWER DOOR LOCK CONTROL Optional This system enables you to remotely lock and unlock the vehicle s doors if equipped with power locks via remote control for safety and convenience Note This feature may require extra labor and or parts to install Press the Lock or Unlock transmitter button as you leave or come near the vehicle Parking lights will flash once for lock and twice for unlock If vehicle is running by the remote start system the lights will flash but return back to solid AUTO LOCK UNLOCK Improved The Auto Lock feature controls whether the doors will automatically lock unlock on your vehicle when driving or with turning the Ignition ON OFF If the Auto Lock feature is turned on and your system is in Tach mode then the doors should automatically lock as the engine RPM increase driving If the Auto Lock feature is turned on and your system is in Smart Tachless mode then the doors will lock a few seconds after the Ignition is turned on When the Auto Lock feature is turned on the system will always unlock the doors when the Ignition is turned off With this feature turned OF
12. ey is turned too far to the start position while engine is already running from the remote starter The Anti Grind Starter Disable requires the use of an external relay This system must be programmed to allow the relay to work as a starter disable Driver s Door Priority Optional additional part may be needed When using the optional separate drivers and passenger unlock function press and release button 2 Unlock symbol on the transmitter to unlock drivers door only then press the 2 button again within 2 4 seconds to unlock remaining doors This feature is optional and requires additional parts and or labor HOOD OPEN SAFETY Requires grounding hood pin installation Prevents the engine from being Remote Started when hood is open and will shut OFF the engine if opened during while remote started Eliminates risk of injury to someone working under the hood of the vehicle with a properly working hood pin installed If Remote Start button is pressed with the hood open the lights will flash once and the unit will not attempt a start BRAKE PEDAL RESET Prevents starting or shuts off a remote started vehicle when this circuit is active or activated Prevents unauthorized tampering This circuit shuts the system down immediately when brake pedal is pressed if the key is not in ignition and turned to the ON position OEM ALARM INTERFACE This feature is designed to Disarm and Re arm Factory equipped security systems in conjunction with remote s
13. he REV B 08 2006 TABLE OF CONTENTS Operation Cauons amp Warnings erener aer aa a e a niu iiaasduenisaiadds EE a A a aA pa e noia 2 CAD 01121110 a E E E E E E pete E E E 3 Remote Engine Starting ldle Down Mode Infinity Run MOE 2 20cccceccnccncenceeenseetensesenaeeneaeseateestaes 4 7 TONDO Timer MOOG v2 53 a2 shove rea A huss Sele eeate a cee ece hm ethical oats Sen E ele tam fess 8 Convenience and Safety Features se cunt tele oh aii lad ht UNS cel can Ae al el Ad ity 9 10 TANS MINGE Programit Ng sco scusec abel scecene fe fens ovat Gustnaa oaa asm ese leaden ubaseidne E E EE a Er AEE aE TROE EE 11 2 VOICI OUST ANON EE E E ATE E E E A 12 Troubleshooting Before You Call s sesnnsannnnsnesnsennnnerrrerrnnrrrrrerrrerrrrrrrrrrrrnrrrrrrrrrrrrrrrrrrr nrn rrr nne 12 13 OPERATION CAUTIONS amp WARNINGS CRIMESTOPPER SECURITY PRODUCTS INC and its VENDORS shall not be liable for any accident resulting from the use of this equipment This system is designed to be professionally installed into a car or vehicle in which all items such as parking brake and all associated components door switches transmission Shift linkage throttle linkage and all engine safety features are in perfect working condition DO NOT install the Remote Engine Starting System on MANUAL TRANSMISSION vehicles If accidentally left in gear the vehicle could become a self propelled threat to life and property IT IS ABSOLUTELY THE OWNER S SOL
14. ic trunk or illuminate the interior light when you unlock your vehicle for lighted entry at night If you have the optional trunk pop installed simply press and release the Trunk Button 3 on the transmitter or if option 6 is turned on you must press Button 3 twice within 3 seconds to remotely open trunk If your system is programmed for Dome Light illumination then it will work automatically lighting the dome light for 30 seconds when you unlock your vehicle via the remote The dome light will turn off after 30 seconds or turning the key on whichever comes first The trunk Pop or Dome Light Illumination may require extra labor and or parts to install 9 CONVENIENCE AND SAFETY FEATURES VALET MODE STARTER DISABLE OVERRIDE Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into valet mode The remote start function WILL NOT operate when in Valet mode To enter Valet mode turn the key to the ON position press and hold Program Valet switch for 5 6 seconds The LED will turn on solid and the system is now in valet Perform this procedure again to exit of Valet mode The keyless entry will still function normally while in valet mode In the event of a lost or broken transmitter perform this step to override the Starter Disable if installed ANTI GRIND STARTER DISABLE Optional relay not included This Optional feature prevents the user from accidentally grinding the starter if the Ignition k
15. nning for programmed run time or until you return whichever comes first SOLID O00 Ove 4 l UNLOCK ENTERING A VEHICLE DURING IDLE DOWN or INFINITY RUN MODES 1 With engine running in IDLE DOWN parking lights ON unlock door via remote or key 2 Enter vehicle and be careful not to step on brake pedal Remote Start Reset 3 Turn Ignition to ON RUN position then depress brake pedal to reset the Remote Starter Parking lights will turn off indicating the Remote Start is OFF and Vehicle is running by the Key Drive away as normal INFINITY RUN MODE This mode can only be activated when Idle Down procedure The Infinity Run mode allows the vehicle engine to remain running INDEFINITELY after the programmed run time elapses This mode will allow the vehicle to be left running and unattended without the ignition key in the switch preventing the vehicle from being stolen This mode can be beneficial to law enforcement or commercial trucks that need to remain running unattended for long periods of time See next page for Infinity mode steps Programmable for 1 2 second press or double press This option is selectable by your installer 6 REMOTE ENGINE STARTING Cont Infinity Run Mode INFINITY RUN MODE EXITING THE VEHICLE 1 With vehicle engine running with the key press the Remote Start button for at least 1 2 second pause a few seconds then press and release the remote start button a second time 2
16. r vehicle REMOTE START RUN TIME RESET You can now reset the engine run timer to allow for more running time after remote start has already occurred using the remote control After a successful remote start press both the Lock amp Unlock buttons together for at least 2 seconds The parking lights will flash 3 times and internal engine timer will reset back to zero minutes REMOTE ENGINE STARTING Cont IDLE DOWN MODE IDLE DOWN MODE This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and you exit the vehicle The vehicle is put into a remote running condition before you exit and it will remain running for the programmed run time or until you come back Examples e You pull up to a convenience store for a quick stop Idle Down mode keeps engine running when you exit the vehicle with keys in hand remote lock doors or arm alarm When you return unlock turn ignition ON and drive away REMOTE ENGINE STARTING Cont IDLE DOWN MODE IDLE DOWN MODE EXITING THE VEHICLE 1 With vehicle engine running with key press the Remote Start button for at least a 1 2 second or twice if set for double press 2 Parking Lights will turn ON 3 Doors will unlock or if brake pedal is being depressed doors will unlock when it is released 4 Turn OFF Ignition and remove key Engine should remain running 5 6 Exit vehicle then remote lock doors if desired Engine will remain ru
17. tart and keyless entry if needed for your vehicle This feature will maintain the original integrity and security of your vehicle s factory equipped systems before during or after remote start NOTE When changing charging or jumpstarting the vehicle s battery we recommend removing the main power fuses located on the heavy gauge RED wires near the remote start module 10 TRANSMITTER PROGRAMMING Note All transmitter codes must be learned at time of programming The unit will learns up to 4 different transmitter codes 1 Turn key to the ON position 2 Press Programming button 4 times then after a few seconds the unit flashes the parking lights 4 times 3 Press button 1 on the transmitter to be coded You should get 2 light flashes indicating the unit is waiting for a 2 code then press button 1 on the second transmitter the unit will flash 3 times indicating its waiting for the 3 code and so on If all 4 codes are learned the unit will automatically exit code learning mode otherwise turn key off See diagram below D Pos 3 IGN OFF gt gt WAIT FOR 4 FLASHES PRESS 4X s N IGN OFF FLASH 2 3 or 4 X s 11 2 VEHICLE OPERATION A single remote can control two different vehicles EZEE START systems installed However both systems must be the same type EZ 45DP II 55DP Il are only compatible with each other Programming You must first Programming your remote for 2 vehicle operation 2 V
Download Pdf Manuals
Related Search