Cooper Lighting Invue Vision Wall User's Manual
Contents
1. opposed When used with Thru Way Mounting Box Accessory VWM TB unit can only be mounted downward These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative a COOPER Lighting AVU0331422. or attempting any maintenance Standard Mounting Kit 1 The standard mounting kit may be mounted to any standard embedded 4 junction box It is not for use with a surface mounted J box For orientation of fixture to the junction box See Fig 1 Using the two 2 screws supplied with the junction box install the mounting plate as shown The 5 16 18 studs should be facing away from the wall and above the Apply Sealant center of the bracket See Fig 2 For rough or uneven As Required surfaces sealant must be applied by others between iia aa the rear mounting plate gasket and the mounting surface wall In addition to the screws supplied with the junction box the unit must be supported by 1 4 anchor screws supplied by others installed through the four 4 holes provided See Fig 3 12 9 16 319 16mm 411 16 118 6mm 233 12mm Fig 1 These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative COOPER Lighting AVU033142 INVUE INSTALLATION INSTRUCTIONS IMPORTANT Read carefully before installing fixture Retain for future reference VISION WALL Sheet 3 of 4 sava
3. INVUE INSTALLATION INSTRUCTIONS IMPORTANT Read carefully before installing fixture Retain for future reference VISION WALL Sheet 4 of 4 s2asos mraos WARNING Make certain power is OFF before starting installation or attempting any maintenance Adjustment Of Light Throw Your Vision Wall luminaire has an adjustable forward light throw Adjustment 1 Obtain a 3 16 allen wrench 2 Locate the stainless steel button head screw on the outside of the fixture See Fig 4 Turn the screw clockwise to pivot the reflector and throw the light forward You may monitor the reflector rotation by viewing the bottom edge of the reflector and the indicator located inside the fixture This is viewable through the glass See Fig 5 Rotating the screw counter clockwise brings the reflector back down to zero Degree Indicator Fig 5 CAUTION Prior to installing lamp in the fixture verify that lamp source and wattage correspond with the fixture label Lamp should be screwed securely into the socket Do not over tighten WARNING Recheck to be sure that the fixture has been wired properly Improper wiring may result in ballast failure which voids all warranties Cleaning The reflector and door glass may be cleaned with any suitable non abrasive glass cleaning solution soap or detergent and rinse with clean water The reflectors efficiency will be retained only if cleaned at re
4. gular intervals Clean with mild soap or detergent and water or liquid wax emulsion The refractor should also be cleaned along with the reflector using care not to chip glass surfaces CAUTION Do not use abrasive strong alkaline or acid cleaners These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative www cooperlighting com Customer First Center 1121 Highway 74 South Peachtree City GA 30269 770 486 4800 FAX 770 486 4801 AVU033142 COOPER Lighting INV UE INSTALLATION INSTRUCTIONS IMPORTANT Read carefully before installing fixture Retain for future reference VISION WALL Sheet 1 of 4 General Upon receipt of fixture thoroughly inspect for any Safety This fixture must be wired in accordance with freight damage which should be brought to the attention of the national electrical code and applicable local codes the delivery carrier Compare the catalog description listed and ordinance Proper grounding is required to insure on the packing slip with the fixture label on the housing to personal safety Carefully observe grounding procedure assure you have received the correct merchandise under installati
5. on section All work should be done by a qualified electrician WARNING Make certain power is OFF before starting installation or attempting any maintenance Your Vision Wall Luminaire has three different types of mounting interface 1 Standard Mount mounts to any standard 4 J box Included with every fixture Gee Fig 1 2 Embedded Mount mounts to a plate embedded into the wall Optional Accessory VWM EM See Fig 2 3 Thru Way Box mounts to surface mounted casting allowing a conduit run Optional Accessory VWM TB See Fig 3 i NOTE 7 Fig 2 Embedded Mount Kit Please refer to your mounting kit for specific instructions EMBEDDED MOUNT VWM EM Thru Way Mounting Conduit run by others standard Mount Kit 4 J Box By Others screws to J Box Fig 1 Fig 3 STANDARD MOUNT THRU WAY BOX VWM TB These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative I COOPER Lighting AVU033142 INV UE INSTALLATION INSTRUCTIONS IMPORTANT Read carefully before installing fixture Retain for future reference VISION WALL Sheet 2 of 4 WARNING Make certain power is OFF before starting installation
6. s ea im a98 WARNING Make certain power is OFF before starting installation or attempting any maintenance Installing the Fixture You may install the fixture with the light up or down as desired Make sure all power is off Visually inspect the mounting bracket to insure correct placement and check for damaged gaskets Refer to the specific mounting instruction sheet used with your fixture Loosen the four 4 1 4 20 captive socket head cap screws and open the door Locate two 2 reflector latches on either side of the forward end of the reflector See Fig 1 Turn the latches to disengage and pivot the reflector assembly out of the way See Fig 2 Thread the incoming power leads through the large center hole in the rear of the fixture while lining up the bolts or threaded studs with the keyhole slots in the rear See Fig 3 Carefully slide the fixture down the keyhole taking care not to damage the gaskets Thread Power Feed Lines Tighten the screws or nuts Depending on mounting type Teac DO NOT CAULK AROUND THE FIXTURE Have a qualified electrician make the power connections Push the supply wires back through the center hole and Wr ha 977 A r down in the rear fixture cavity p 7 fy N K 4 LEA 12 Swing the reflector assembly back up and latch into 1 position 13 Install the door and four 4 1 4 20 screws Tighten the screws diagonally
Download Pdf Manuals
Related Search