Cooper Lighting IMI-694 User's Manual
Contents
1. 4 To close the luminaire rotate lens back up to position Lift up the lens and align with 4 ribs of top lens on both sides Figure 8 CAUTION Latching luminaire closed prior to having proper alignment will result in lens breakage 5 Push one side of the latch up to grasp edge of lens and then push inward to complete latching Figure 9 amp 10 Repeat for the other latch Figure 8 ALIGN THESE RIBS AS SHOWN BEFORE LATCHING OTHER SIDE NOT SHOWN Figure 6 PULL TO PULL TO UNLATCH UNLATCH Figure 9 Figure 7 LATCH UP TO GRASP EDGE OF LENS BEFORE LATCHING Figure 10 PUSH TO PUSH TO LATCH LATCH Ci SUPPORT LENS WHILE IT SWINGS OPEN These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative NOTE Specifications and dimensions subject to change without notice Saar cent cane 8 ee Co Customer First Center 1121 Highway 74 South Peachtree City GA 30269 770 486 4800 FAX 770 486 4801 ADH080771 COOPER Lighting McGraw Epison The Architecture of For2. Lighting McGraw Epison EPL Envoy The Architecture of Form amp Light Parking Luminaire INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE RETAIN FOR FUTURE REFERENCE THRU BRANCH WIRING INSTALLATION Figure 13 amp 14 NOTE Use 90 C wire rating for luminaire with thru branch option for fixtures 100w or below at 25 C ambient temperature applications KNOCK OUT WIRE JE Use 105 C wire rating for luminaire with thru branch option for FEATURE BY OTHERS 150w to 175w at 25 C ambient temperature applications KNOCK OUT Use 125 C wire rating for luminaire with thru branch option for anes FEATURE 200w at 25 C ambient temperature applications THRU BRANCH Use 150 C wire rating for luminaire with thru branch option for all N FEATURE fixtures at 40 C ambient temperature applications Figure 13 10 24 X 5 8 TAPTITE SCREW BY OTHERS WARNING RISK OF FIRE DO NOT mount on or near combustible materials PeP Note Requires luminaire option CT Conduit Tap 2 34 NPSM taps and plugs KNOCK OUT FEATURE 1 Remove lens and housing cover from luminaire 2 Remove conduit plugs KNOCK OUT 3 Affix luminaire to the ceiling with anchors through cast in knock outs oe anchors provided by others Use RTV or other liquid sealant around perimeter of KO s 4 Apply sealing compound to end of pipe if applicable Install conduit pipe Figure 14 5 Route wires inside the housin
3. McGraw Epison The Architecture of Form amp Light INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE RETAIN FOR FUTURE REFERENCE A GENERAL Upon receipt of luminaire thoroughly inspect for any freight damage which should be brought to the attention of the delivery carrier Compare the catalog description listed on the packing slip with the luminaire label on the housing to assure you have received the correct merchandise SAFETY This luminaire must be wired in accordance with the national electrical code and applicable codes and ordinances Proper grounding is required to insure personal safety Carefully observe grounding procedure All work should be done by a qualified electrician EPL Envoy Parking Luminaire Sheet 1 of 5 8 20 08 IMI 694 WARNING Make certain power is OFF before starting installation or attempting any maintenance WARNING Risk of Electric Shock Disconnect power at fuse or circuit breaker before installing or servicing WARNING Risk of Burn Disconnect power and allow luminaire to cool before changing lamp or handling luminaire WARNING This luminaire is for use with downlight applications only WARNING RISK OF FIRE DO NOT mount on or near combustible materials FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH Figure 1 NOTE Use minimum 90 C supply wire rating for connections in J box BOK Fixture Orientation Guideline Proper orie
4. g as shown and use wire ties and screws to nostot iat nee restrain in position FEATURE WPETE CAUTION Use wire ties self tapping screws to restrain wires from WiRETIE BY OTHERS contacting ballast provided by others BY OTHERS KNOCK OUT CONDUIT FEATURE PIPE THRU BRANCH FEATURE KNOCK OUT FEATURE KNOCK OUT FEATURE These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative NOTE Specifications and dimensions subject to change without notice EES Customer First Center 1121 Highway 74 South Peachtree City GA 30269 770 486 4800 FAX 770 486 4801 ADH080771 COOPER Lighting
5. hers 2 Screws handle into adapter 3 Aim handle to a preferred position and lock it in position 4 Aim task light head to a preferred position and tighten 10 24 Allen head screw with provided Allen wrench 5 Pull wires through access and restrain with wire tie Note Depending on which task light option is being ordered additional wiring routing will be necessary Reference wiring diagrams shipped with task light These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation EPL Envoy Parking Luminaire Sheet 4 of 5 Figure 11 CONDULET TOP TRUNNION L g 10 24 FLAT CS SCREW TOP PLATE gt TRUNNION NIPPLE APPLY SEALING COMPOUND BY OTHERS HOUSING FOR VERTICAL ADJUSTMENT UP OR DOWN ONLY 8 3 8 TO 13 1 4 FROM TOP OF LUMINAIRE Figure 12 HANDLE APPLY SEALING COMPOUND BY OTHERS TASK LIGHT ALLEN HEAD LOCK NUT operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative NOTE Specifications and dimensions subject to change without notice ete Customer First Center 1121 Highway 74 South Peachtree City GA 30269 770 486 4800 FAX 770 486 4801 ADH080771 8 20 08 IMI 694 COOPER
6. m amp Light INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE RETAIN FOR FUTURE REFERENCE TRUNNION MOUNT INSTALLATION Figure 11 Note Use minimum 90 C supply wire when installed per below procedure and connections are made inside of condulet body Note For 8 3 8 to 13 1 4 vertical adjustment Up or Down only 1 Install top trunnion on the ceiling using masonry anchors provided by others 2 Apply sealing compound by others on one end of 1 2 nipple 3 Screw nipple into the housing 4 Install bottom trunnion L brackets on the top plate with provided 10 24 pan head screws lock washers and nuts Torque between 24 27 in lb 5 Install top plate on the housing with provided 10 24 flat head screws Torque between 24 27 in lb 6 Pull wires from back of luminaire through nipple to make for easy routing into condulet body 7 Apply sealing compound to top of nipple Screw condulet body onto nipple 8 Install bottom trunnion L brackets to the top trunnion with provided 3 8 bolts lock washers and nuts Torque between 17 20 ft lb 9 Route conduit and power supply wires to condulet body 10 Make connections Push excess wires and connectors back into the condulet body 11 Install gasket and cover TASK LIGHT INSTALLATION Figure 12 WARNING RISK OF FIRE DO NOT mount on or near combustible materials 1 Apply sealing compound on the threads of handle provided by ot
7. ntation of luminaire may vary based upon design requirements specified per given application Labels are supplied on top of fixture and mounting plate for reference to proper fixture alignment Align quick mount plate in correct direction by referencing number of fixtures required double or single row luminaire installation to direction of arrows Direction of arrow s should be in line with direction of traffic a a CENTER ACCESS HOLE QUICK MOUNT PLATE 8 32 SCREW Figure 2 ALIGN ARROWS WITH DRIVING LANE lt o SINGLE ROW FIXTURE INSTALLATION INSTALLATION QUICK MOUNT PLATE DRIVING LANE DOUBLE ROW FIXTURE REAR HOOKS ALIGN ARROWS WITH LUMINAIRE T HANGING HOOK Figure 3 HANGING HOOK LIFT UP 4 THEN PUSH K LUMINAIRE LUMINAIRE INSTALLATION 1 Install quick mount plate on a 4 junction box as shown in Figure 1 Note the required position of plate to ensure correct light beam orientation from fixture See guidelines above or labels on top of fixture housing and mounting plate if applicable 2 Secure hanging hook into the rear hooks of quick mount plate Figure 2 amp 3 3 Make wiring connection while luminaire is being suspended from hanging hook 4 Push excess wires and connectors up into the junction box through center access hole These instructions do not claim to cover all details or variations in the equipment procedure or process de
8. scribed nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative NOTE Specifications and dimensions subject to change without notice Customer First Center 1121 Highway 74 South Peachtree City GA 30269 770 486 4800 FAX 770 486 4801 ADH080771 COOPER Lighting McGraw Epison EPL Envoy The Architecture of Form amp Light Parking Luminaire INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE RETAIN FOR FUTURE REFERENCE 5 Lift up luminaire onto the 4 four hooks of quick mount plate while guiding the wires through center access hole Figure 3 i 6 Push luminaire forward for engagement Figure 3 When it reaches the p Z Se STAMPER PROOE full engaged position a CLICK can be heard n SCREW FOR LATCH CAUTION If full engagement is not reached it is not yet rigidly installed A Figure 4 REMOVAL OF LUMINAIRE SONEN FORHANDLE WARNING Make sure the power to the unit is OFF and allow it to cool 1 Note Remove tamper proof screws first if luminaire includes TR tamper resistant option Figure 4 2 To release clasp lock on quick mount bracket push handle inward and pull luminaire forward Figure 5 CAUTION Do not let luminaire fall Support luminaire while lowering off of j bo
9. x to resting hanging position 3 Remove hanging hook from quick mount plate Figure 2 amp 3 CAUTION Support luminaire while removing 4 For re installation of luminaire refer to steps 1 through 6 on Luminaire Installation Figure 5 TO REMOVE These instructions do not claim to cover all details or variations in the equipment procedure or process described nor to provide directions for meeting every possible contingency during installation operation or maintenance When additional information is desired to satisfy a problem not covered sufficiently for user s purpose please contact your nearest representative NOTE Specifications and dimensions subject to change without notice a en S Customer First Center 1121 Highway 74 South Peachtree City GA 30269 770 486 4800 FAX 770 486 4801 ADH080771 COOPER Lighting McGraw Epison EPL Envoy The Architecture of Form amp Light Parking Luminaire INSTALLATION INSTRUCTIONS IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE RETAIN FOR FUTURE REFERENCE LAMP INSTALLATION 1 To install the lamp unlatch both latches Figure 6 Note Remove tamper proof screws first if luminaire includes TR tamper resistant option Figure 4 2 Allow lens to swing open Figure 7 Lens will remain captive CAUTION Support lens while it swings open 3 Install lamp securely into socket CAUTION Verify that lamp source and wattage correspond with the luminaire label
Download Pdf Manuals
Related Search