Coleman 2000001597 User's Manual
Contents
1. UL approved cords rated for outdoor usage Fig 20 we Rainfly Cooler Access The smaller zippered opening at the back of tent is designed for added ventilation and easy access to your beverage cooler 1 To use as a vent unzip flap to expose screen Fig 21 2 To use as a cooler access unzip other flap to make an avenue to bring beverages into tent Fig 22 2 Assemble thin black shock corded Awning Pole with metal tips then insert through sleeve in Rainfly above door Fig 12 donr amp Window Flaps Vents For better ventilation unzip door flaps roll and insert toggle into fabric loop to secure 2 To open back and side window vents for more ventilation unzip then roll up and insert toggles through fabric loops 3 Insert tapered metal tip on Awning Pole into grommet located on web strap clipped to center Leg Pole Fig 13 4 Go to opposite center Leg Pole on other side of door and gradually apply pressure to the pole forming an arch Insert metal tip into the grommet 9 Locate all hook amp loop fasteners on underside of Rainfly and wrap around Leg Poles and Awning Pole locations Fig 14 To Store 1 All poles and stakes must be placed in the storage bag to prevent damage to the fabric items placed in the carry case 2 Make sure tent is clean and dry before placing in carry case 3 Remove rainfly spread out on floor of tent then unzip door amp vents before taking tent down2. for weeks at a time Be aware that exposure to ultraviolet rays from the sun can seriously damage material and or cause it to become discolored AX WARNING Keep all flame and heat sources away from this tent fabric This tent meets the flammability requirements of CPAI 84 The fabric may burn if left in continuous contact with any flame source The application of any foreign substance to the tent fabric may render the flame resistant properties ineffective Attaching Room Divider 1 Divider Panel can be installed through center of the tent by inserting toggles through the top and bottom fabric loops as shown Fig 18 amp 19 The Coleman Company Inc 3600 N Hydraulic Wichita Kansas 67219 1 800 835 3278 www coleman com MADE IN CHINA PRINTED IN CHINA 2008 The Coleman Company Inc Coleman A and Weathermaster are registered trademarks of The Coleman Company Inc 4010004005 20081030 AS
3. STITCH LINE Before you begin Read all instructions before set up e Select a level site clear of rocks branches and other hard or sharp objects to install your tent AXWARNING Keep clear of overhead power lines e Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather e Secure with all stakes and guylines provided to prevent property damage Or personal injury e For best results in windy conditions position narrow end of tent into the wind e Enlist the help of at least one other person to assist you when it is time to assemble the tent Pole Descriptions Pole Pole Pole Description Qty Dia Repair Kit Replacement Kit Long Leg Pole steel w red marking 4 19mm N A 9010000608 Short Leg Pole steel 4 19mm N A 5010000610 Curved Ridge Pole steel w red marking 2 19mm N A 5010000607 Curved Ridge Pole steel 2 19mm N A 5010000609 Awning Pole black fiberglass metal tips 1 63mm 5010000543 5010000545 Door Pole long thin black fiberglass rubber tips 1 63mm 5010000543 5010000545 Vert Door Pole short black fiberglass rubber tips 1 63mm 5010000543 5010000545 To Set Up Tent 1 Unfold tent and spread out on a clean level surface with the door facing the desired direction Unzip doors Fig 1 2 Pull four corners of tent taut then secure by driving stakes through web loops at an angle for better anchoring Fig 2 3 Assemble four s
4. eg Pole Section Button Center Hole Lower Hole Lower Leg Pole Section 9 Insert plastic stakes through web Straps located on both sides of tent then drive in to secure Fig 10 NOTE It may be necessary to remove metal stakes through web straps at Side of tent and screen room pull tent taut and drive in stakes to secure mee Rigid Door Assemble Vertical Door Pole shorter black pole with plastic cap tips then insert through zippered vertical pole sleeveon hinged side of door Fig 11 2 Insert end of Vertical Door Pole into bottom hinge plate apply pressure to form a slight bow then insert other tip of pole into top hinge Zip up vertical pole sleeve Fig 12 amp 13 3 Assemble Door Pole longer black pole with plastic cap tips then insert into zippered pole sleeve at top of door Fig 14 4 Insert end of Door Pole into top hinge plate apply pressure to form a bow then insert other tip of pole into the bottom hinge Fig 15 9 Zip up pole sleeve to enclose Door Pole Fig 16 Vertical Pole Sleeve Door Hinge oa continued on other side To Attach Rainfly E Cord Access 1 Drape Rainfly over tent Make sure seams on Rainfly are Unzip access panel in the lower facing down and centered over poles of the tent Fig 11 left corner of tent and bring in NOTE Hook and loop fasteners located on seams of under electrical cord side of Rainfly should be centered over Ridge Poles NOTE Use only
5. for storage 4 Neatly fold tent to width of pole storage bag place on tent roll tightly and place in carry case 5 Store in a clean dry area 6 Insert metal hook Center on elastic straps on Leg Pole Things You Should Know e Under certain conditions cold weather high humidity etc condensa tion will form on the inside of your tent Condensation is caused by water vapor from your breath perspiration or any wet clothing inside the tent Location Rainfly into the hole on each Leg Pole Fig 15 amp 16 It is NOT LEAKAGE through the tent fabric It can be minimized by removing wet clothing from your tent and by providing good ventila 7 Loop ends of guylines over stakes stretch tight tion through the tent l l a then hammer into ground at an angle as Tree limbs tree sap bird droppings or moisture steadily dripping off l tree limbs can cause damage to the tent fabric and its coating resulting shown Fig 17 amp 17A a S in leaks or loss of flame resistant properties Never store tent even for a short period of time without drying it thoroughly and brushing off caked dirt Do not pack stakes or poles inside your tent Use a separate storage bag Stakes should be removed by pulling on the stake itself NEVER PULL ON THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY Tent poles should not be left telescoped together during storage Do not leave your tent set up
6. teel shock corded curved Ridge Poles Insert Ridge Poles with red marking into center sleeves on top of tent with the red trim Fig 3 Insert the remaining curved Ridge Poles into the other two sleeves on top of tent 4 Assemble eight steel shock corded Leg Poles Push down on steel button on tapered end and insert into end with four holes NOTE Make sure steel button locks into third hole on pole as shown Fig 4 5 Insert curved end of Leg Poles with red marking into the ends of the Ridge Poles with red marking Insert curved end of remaining short Leg Poles into the ends of the remaining Ridge Poles Fig 5 amp 6 Ridge Pole with Red Marking n l Law Ridge Pole with Red Marking m Sleeve i with Red Trim Curved Ridge mAN Poles with Red he E Marking in aa en i center 2 sleeves WEATHERMASTER 6 SCREENED TENT MODEL 2000001597 6 Rotate all eight Leg Poles upright and insert pin on each web loop at the side locations as shown Fig 7 amp 7A 7 Locate the plastic hooks at sides and corners of tent then snap onto Leg Poles to attach Fig 8 8 To stretch tent to finished size e Push in button on Leg Pole while twisting lower Leg Pole section counterclockwise Fig 9 e Pull up on top Leg Pole section until tent is taut e Twist the lower Leg Pole clock wise until the button locks into the center or lowest hole e Repeat on remaining Leg Poles Upper L
Download Pdf Manuals
Related Search