Coleman 2000001596STITCHLINE User's Manual
Contents
1. 3 g Insert the remaining curved Ridge Poles into the other two sleeves on top of tent ke 4 Assemble six steel shock corded rr Ne Leg Poles Push down on steel button N Mnn on tapered end and insert into end with four holes NOTE Make sure steel button locks into third hole on pole as shown Fig 4 5 Insert curved end of Leg Poles with red dot into the ends of the RidgePole with red dot Insert curved end of remaining short Leg Poles into the ends of the remaining Ridge Poles Fig 5 amp 6 Ridge Pole with Red Marking Ridge Pole with Red Marking Curved End of Sleeve Long Leg Pole Trim 6 11 12 Locate web strap Rotate all six Leg Poles upright and insert pin on each web loop at the side locations as shown Fig 7 amp 7A e N Pole then insert one into sleeve located at each end of tent Fig 7 amp 7B Insert tapered metal tip on Window Pole into Leg Pole NOTE It may be necessary to gently rotate Leg Pole so the hole will line up with the Window Pole Go to opposite end of each window pole and gradually apply pressure to the pole forming an arch Insert the pin into the leg pole end at the corners of tent Fig 7 amp 7C Locate the plastic hooks at sides and corners of tent then snap onto Leg Poles to attach Fig 8 with plastic hook on the sides of each end panel Window Vent then snap onto the corner Leg Pole Fig 9 Corner Le2. Window Flaps Vents For better ventilation unzip door flaps roll and insert toggle into fabric loop to secure 2 To open back and side window vents for more ventilation unzip then roll up and insert toggles through fabric loops To Store 1 All metal poles and stakes must be placed in the storage bag to prevent damage to the fabric items placed in the 3 Insert metal hook on elastic straps on Rainfly into the hole on each Leg Pole Fig 14 amp 15 carry Case poe 2 Make sure tent is clean and dry before placing in carry case py Comer Leg eee 3 Remove rainfly spread out on floor of tent then unzip oul g Pole door amp vents before taking tent down for storage 4 Neatly fold tent to width of pole storage bag place on tent roll tightly and place in carry case 5 Store in a clean dry area 4 Loop ends of guylines over stakes Stretch tight then hammer into ground at an angle as shown Fig 16 amp 17 Things You Should Know e Under certain conditions cold weather high humidity etc condensa tion will form on the inside of your tent Condensation is caused by water vapor from your breath perspiration or any wet clothing inside the tent It is NOT LEAKAGE through the tent fabric It can be minimized by removing wet clothing from your tent and by providing good ventila tion through the tent Tree limbs tree sap bird droppings or moisture steadily dripping off tree limbs can cause damage to t
3. 1113 AS
4. STITCH LINE WEATHERMASTER 8 TENT mone 200000159 Before you begin Read all instructions before set up e Select a level site clear of rocks branches and other hard or Sharp objects to install your tent Ay WARNING Keep clear of overhead power lines e Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather e Secure with all stakes and guylines provided to prevent property damage or personal injury e For best results in windy conditions position narrow end of tent into the wind e Enlist the help of at least one other person to assist you when it is time to assemble the tent Pole Descriptions Pole Pole Pole Description Qty Dia Repair Kit Replacement Kit Long Leg Pole steel w red marking 2 19mm N A 5010000612 Short Leg Pole steel 4 19mm N A 5010000622 Curved Ridge Pole steel w red marking 19mm N A 5010000617 Curved Ridge Pole steel 2 19mm N A 5010000616 Window Vent Pole black fiberglass 2 8 5mm 5010000541 5010000547 To Set Up Tent 1 Unfold tent and spread out on a clean level surface with the door facing the desired direction Unzip doors Fig 1 2 Pull four corners of tent taut then secure by driving stakes through web loops at an angle for better anchoring Fig 2 3 Assemble three steel shock corded curved Ridge Poles Insert Ridge Pole with red marking into center sleeve on top of tent with the red trim Fig
5. g Pole To stretch tent to finished size 3 e Push in button on Leg Pole while twisting lower Leg Pole section counterclockwise Fig 10 e Pull up on top Leg Pole section until tent is taut e Twist the lower Leg Pole clock wise until the button locks into the center or lowest hole e Repeat on remaining Leg Poles Upper Leg Pole Section Button Center Hole Lower Hole Lower Leg Pole Section Insert plastic stakes through web straps located on both sides of tent then drive in to secure Fig 11 continued on other side To Attach Rainfly ra eta Cord Access 1 Drape Rainfly over tent Make sure seams on Rainfly are Unzip access panel in the lower facing down and centered over poles of the tent Fig 12 left corner of tent and bring in NOTE Hook and loop fasteners located on seams of under electrical cord side of rainfly should be centered over black and gray poles NOTE Use only UL approved cords rated for outdoor usage Fig 20 Ray Cooler Access The smaller zippered opening at the side of tent is designed for added ventilation and easy access to your beverage cooler 1 To use as a vent unzip flap to expose screen Fig 21 2 To use as a cooler access unzip other flap to make an avenue to bring beverages into tent Fig 22 2 Locate all hook amp loop fasteners on underside of rainfly and wrap around each Leg Pole and Window Vent Pole locations Fig 13 nia amp
6. he tent fabric and its coating resulting in leaks or loss of flame resistant properties Never store tent even for a short period of time without drying it thoroughly and brushing off caked dirt Do not pack stakes or poles inside your tent Use a separate storage bag Stakes should be removed by pulling on the stake itself NEVER PULL ON THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY Tent poles should not be left telescoped together during storage Do not leave your tent set up for weeks at a time Be aware that exposure to ultraviolet rays from the sun can seriously damage material and or cause it to become discolored AX WARNING Keep all flame and heat sources away from this tent fabric This tent meets the flammability requirements of CPAI 84 The fabric may burn if left in continuous contact with any flame source The application of any foreign substance to the tent fabric may render the flame resistant properties ineffective The Coleman Company Inc e 3600 N Hydraulic e Wichita Kansas 67219 1 800 835 3278 www coleman com MADE IN CHINA PRINTED IN CHINA 2008 The Coleman Company Inc Coleman m AR and Weathermaster are registered trademarks of The Coleman Company Inc Attaching Room Divider 1 Divider Panel can be installed through center of the tent by inserting toggles through the top and bottom fabric loops as shown Fig 18 amp 19 4010004004 2008
Download Pdf Manuals
Related Search