Home

Cobra Electronics MICROTALK PR5000DX Owner's Manual

image

Contents

1. vox Icon 8 Scan Icon Memory Receive leon Transmit TIE n Location Number Channel Numbers Power 9 Battery 8 Saver Icon Level Privacy Code Indicator M mbers Maximum range may vary and is based on unobstructed line of sight communication under ideal conditions Important FCC Licensing Information This radio operates on General Mobile Radio Service GMRS frequencies which require a Federal Communications Commission FCC license See page 25 for licensing and other related information Introduction a g Caring for Your microTALK Radio Your microTALK radio will give you years of trouble free service if cared for properly Handle the radio gently Keep the radio away from dust Never put the radio in water or in a damp place Avoid exposure to extreme temperatures Tels Rechargeable Batteries and onw Desktop Charger To insert batteries into radio 1 Remove belt clip by releasing belt clip latch and sliding clip up 2 Pull down on the battery door latch to remove the battery compartment cover 3 Insert the supplied GA BN batteries according to polarity markings May also be used with four AA non rechargeable alkaline batteries per radio not included 4 Replace battery compartment cover and belt clip Estimated operation time on full charge 15 hours These rechargeable batteries must be recycled or disposed of properly in compliance with all applicabl
2. LJ EINEN Oeration M Lock Mode Button nel 7 Channel Buttons V English 7 Choose one of the following a Press the HieLow Enter button to enter the channel privacy code in the selected memory location and return to Step 1 to program another memory location Press the Lock Mode button to enter the channel privacy code in the selected memory location and proceed to other functions on the channel privacy code displayed before you entered mode functions Press the Talk button to enter the channel privacy code in the selected memory location and exit mode functions Upon release of the Talk button the radio will enter Standby mode on the channel privacy code just entered To recall a stored memory channel location 1 Press the Lock Mode button until the Memory icon and the memory location number flash on the display 2 Press the Channel Up or Channel Down button to select a memory location 0 through 9 If a location has been programmed before its associated channel privacy code will be shown on the display 3 Press the Talk button to return to Standby mode on the selected memory location c A memory location can be reprogrammed at any time it is displayed Press the HieLow Enter button to begin While recalling a stored memory location if you do not press any buttons for 15 seconds your radio will automatically return to Standby mode on the channel privacy code displayed
3. the maximum range extender on see below To turn maximum range extender on Press and hold the Light Max Range button for at least five seconds until you hear two beeps which indicates the maximum range extender is on To turn maximum range extender off Press and release the Light Max Range button or change channels Lock Feature The Lock feature locks the Channel Lock Mode and HieLow Power Enter buttons to prevent accidental operation Peso To turn the lock feature on or off Press and hold the Lock Mode button for two seconds A double beep sound is used to confirm your lock on or off request When in Lock mode the Lock icon will be displayed a og LA X Nothing Comes Close to a Cobra h e poaa E Dual Function Buttons Two of the buttons on the microTALK radio have Dual Functions Lock Mode e Press and release the button to scroll to the next mode function e Press and hold the button for two seconds or more to turn the lock function on or of HieLow Power Enter e Press and release the button in standby to change power settings e Press and release in mode functions to enter settings Speaker Microphone Charge Jack Your microTALK radio can be fitted with an external Speaker Microphone freeing your hands for other tasks This same jack also serves as the connecting point for an optional wall charger adapter To attach a speaker microphone Sie 1 Open the speaker microphon
4. 95 of the FCC 22 15 GMRS 462 7250 High or Low rules or violation of type acceptance requirements of part 2 of the rules fa English Nothing Comes Close to a Cobra 25 Product Servi p roduct Service e Customer Aslifbince D L1 Customer Aslfince Product Service Questions If you have any questions about operation or installing your new Cobra product or if you are missing parts Please call Cobra first DO NOT RETURN THIS PRODUCT TO THE STORE See customer assistance on page A1 For Products Purchased in the U S A If your product should require factory service please call Cobra first before sending your radio This will ensure the fastest turn around time on your repair You may be asked to send your radio to the Cobra factory It will be necessary to furnish the following to have the product serviced and returned For warranty repair include some form of proof of purchase such as a mechanical reproduction or carbon of a sales receipt If you send the original receipt it cannot be returned Send the entire product Enclose a description of what is happening with the radio Include a typed or clearly printed name and address of where the radio is to be returned Pack radio securely to prevent damage in transit If possible use the original packing material Ship prepaid and insured by way of a traceable carrier such as United Parcel Service UPS or Priority Mail to avoid loss in transit to Cobra Factory
5. are GMRS only See page 24 for FRS GMRS frequency allocations and compatibility charts fa English Nothing Comes Close to a Cobra 5 M e peona Operation Selectable High Low Power Output When in close proximity to another party or during favorable conditions you can switch from High to Low Power to extend battery life This feature applies to GMRS Channels 4 1 through 7 and 15 through 22 only Channels 8 through 14 operate exclusively on low power To toggle between high and low power Press the HieLow Enter button When using Channels 1 through 7 and 15 through 22 on high power the Hi icon will be visible on the display When using those channels on low power and on Channels 8 through 14 the Low icon will be visible on the display Light Max Range Display Illumination To illuminate your display Press and release the Light Max Range button to illuminate the display for 10 seconds Auto Squelch Maximum Range Your microTALK radio is equipped with Auto Squelch which automatically shuts off weak transmissions and unwanted noise due to terrain and conditions This slightly reduces the Maximum Range at which signals can be heard You can turn off auto squelch to allow all signals to be received and extend the maximum range of your radio reese To briefly turn off auto squelch Press the Light Max Range button for less than five seconds If you hear two beeps you have turned
6. channel privacy code that was displayed before you entered mode functions or the channel privacy code on which during scanning you last received a transmission c Nothing Comes Close to a Cobra M LJ EE Oeration Memory Location Scan Your microTALK radio can automatically scan up to 10 programmed Memory Locations If there are one or fewer memory locations programmed in your radio the scan memory locations option will not be available To program at least two memory locations see program memory locations on page 13 Tr To scan memory locations 1 Press the Lock Mode button until the Scan icon Memory icon and the memory location number flash on the display 2 Press the Channel Up or Channel Down button to begin scanning memory locations The Sean icon and the Memory icon will continue to be displayed when memory location scan is on Your radio will continue to scan memory locations and stop if an incoming transmission is detected Your radio will remain on that memory location for 10 seconds While setting memory location scan if you do not press any buttons for 15 seconds your radio will automatically return to Standby mode on the channel privacy code displayed before you entered mode functions English During memory location scan while receiving an Incoming transmission you can choose from the following a Press and hold the Talk button to communicate on that memory loca
7. for warranty service but the return charges will be at Cobra s expense if the product is repaired or replaced under warranty This warranty gives you specific legal rights and you may also have other rights which may vary from state to state Exclusions This limited warranty does not apply 1 To any product damaged by accident 2 In the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs 3 If the serial number has been altered defaced or removed 4 If the owner of the product resides outside the U S A All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty Cobra shall not be liable for any incidental consequential or other damages including without limitation damages resulting from loss of use or cost of installation Some states do not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you For Products Purchased Outside the U S A Please contact your local dealer for warranty information 90 Day Warranty on GA BN 4 Rechargeable Batteries For products purchased in the U S A and Canada Nothing Comes Close to a Cobra Trademark ji Trademark Acknowledgement Cobra microTALK Nothing Comes Close to a Cobra VibrAlert and the sna
8. Channel 15 Please refer to the chart below for by engaging in permissible transmissions only avoiding channel interference with channel frequency number compatibility other GMRS users and being prudent with the length of their transmission time A Channel No for 22 Channel FRS GMRS Models For licensing information and application forms please call the FCC Hotline at 800 418 FORM Request form 159 and form 605 Questions regarding C Type of Radio Service he license application should be directed to the FCC at 888 CALL FCC D Frequency in MHz Additional information is available on the FCC s website at www fcc gov E Power Output Channel 1 through 7 on low power and channels 8 through 14 comprise the FRS Family Radio Service No license is required to operate on the FRS B Channel No for 15 Channel GMRS Models 5 d 2 E Safety Information for microTALK Radios 1 1 FRS GMRS 462 5625 High or Low Your wireless handheld portable transceiver contains a low power transmitter 2 2 FRS GMRS 462 5875 High or Low When the talk button is pushed it sends out radio frequency RF signals 3 3 FRS GMRS 462 6125 High or Low he device is authorized to operate at a duty factor not to exceed 50 4 4 FRS GMRS 462 6375 High or Low In August 1996 the Federal Communications Commission FCC adopted 5 5 FRS GMRS 462 6625 High or Low RF exposure guidelines with safety levels for handheld wireless devices 6 6 FRS GMRS 462 6875 High or Lo
9. S Cobra V microTALIC s M Owner s Manual TWO WAY RADIO MODEL Printed in Philippines Part No 480 251 P Version A Nothing Comes Close to a Cobra English Introduction a g Staying in touch with your family and friends is convenient and easy when using your microTALK radio Some of the many uses you will discover include Communicating with others while hiking biking and working keeping track of family and friends at a crowded public event checking with travel companions in another car talking with neighbors arranging meeting spots with others while shopping at the mall Secure your microTALK radio while on the go Carrying your microTALK radio with you is easy when using the belt clip The belt clip easily attaches to your belt purse or backpack Simply squeeze the clip and place it where you prefer CustomefPAggistance For Assistance in the U S A In this user s manual you should find all the information you need to operate your microTALK radio If you require further assistance after reading this manual Cobra Electronics offers the following customer assistance services Automated Help Desk English only 24 hours a day 7 days a week 773 889 3087 phone Customer Assistance Operators English and Spanish 8 00 a m to 6 00 p m Central Time Monday through Friday except holidays 773 889 3087 phone Questions English and Spanish Faxes can be received at 773 622 2269 fax Techn
10. Service Cobra Electronics Corporation 6500 West Cortland Street Chicago Illinois 60707 U S A If the radio is in warranty upon receipt of your radio it will either be repaired or exchanged depending on the model Please allow approximately three to four weeks before contacting Cobra for status If the radio is out of warranty a letter will automatically be sent informing you of the repair charge or replacement charge If you have any questions ease call 773 889 3087 for assistance or Products Purchased Outside the U S A Please contact your local dealer for product service information wo N 4 c o p F English Limited One Year Warranty on Radio s amp Charger s For Products Purchased in the U S A Cobra Electronics Corporation warrants that its Cobra microTALK radios and charger and the component parts thereof will be free of defects in workmanship and materials for a period of one year from the date of first consumer purchase This warranty may be enforced by the first consumer purchaser provided that the product is utilized within the U S A Cobra will without charge repair or replace at its option defective microTALK radios chargers products or component parts upon delivery to the Cobra Factory Service department accompanied by proof of the date of first consumer purchase such as a duplicated copy of a sales receipt You must pay any initial shipping charges required to ship the product
11. be able to select or turn on off preferred features of your microTALK radio When scrolling through the Mode Functions your radio features will be displayed in the following order ru EN Set CTCSS Privacy Codes Set VOX On Off Set VOX Sensitivity Level Set Memory Locations Set Channel Scan Set CTCSS Privacy Code Scan Set Memory Location Scan Set Call Alert Tone Signal Set Roger Beep On Off Set Keystroke Tones On Off Scroll through the mode functions using the Lock Mode button Each press and release of the Lock Mode button will advance to the next mode function Press the Talk button at any point to return the radio to Standby mode ele English CTCSS Privacy Codes CTCSS Continuous Tone Coded Squelch System is an advanced tone coding system allowing you to select one of 38 privacy codes to reduce interference from other users on the channel If you are using a privacy code both radios must be tuned to the same channel and privacy code to communicate Each channel will remember the last privacy code you selected To select a privacy code 1 After selecting a channel press the Lock Mode button until the small numbers next to the channel number flash on the display Press using the Channel Up or Channel Down button to select a privacy code You can hold the Up or Down button for fast advance When your desired privacy code is displayed choose one of the following a Press the Lock M
12. before you entered mode functions Lock Mode Button To de program a memory location 1 Press the Lock Mode button until the Memory icon and the memory location flash on the display 2 Press the Channel Up or Channel Down button to select the memory location 0 through 9 If a location has been programmed before its associated channel privacy code will be shown on the display 3 Press the HieLow Enter button The channel numbers will flash on the display 4 Press the Channel Up or Channel Down button to select Channel 0 5 Choose one of the following a Press the HieLow Enter button to enter the channel privacy code in the selected memory location and return to the beginning of memory location options b Press the Lock Mode button to enter the channel privacy code in the selected memory location and proceed to other functions on the channel privacy code displayed before you entered mode functions While de programming a memory location if you do not press any buttons for 15 seconds your radio will automatically return to Standby mode on the channel privacy code displayed before you entered mode functions Nothing Comes Close to a Cobra 5 h LJ EE Operation Channel Scan Your microTALK radio can automatically scan channels English To scan channels 1 Press the Lock Mode button until the Scan icon and the channel numbers flash on the display 2 Press the Chan
13. button to change the setting 3 Choose one of the following a Press the Lock Mode button to enter the selected setting and proceed to other functions b Press the HieLow Enter button to enter the selected setting and return to Standby mode fiz English 10 Memory Locations Your microTALK radio has 10 Memory Locations for storing your most frequently used channels and channel privacy code combinations These Memory Locations can be selected individually or can be scanned See page 20 for memory location scan Peete To program a memory location 1 Press the Lock Mode button until the Memory icon and the memory location flash on the display 2 Press the Channel Up or Channel Down button to select the memory location 0 through 9 If a location has been programmed Channel Buttons before its associated channel privacy code will be shown on the display VA channel 3 Press the HieLow Enter button to enter a new memory location or edit an already programmed memory location The channel numbers will flash on the display 4 Press the Channel Up or Channel Down button to select a channel 1 through 22 5 Press the HieLow Enter button The CTCSS icon and privacy code numbers will flash on the display 6 Press the Channel Up or Channel Down button to select a CTCSS privacy code 01 through 38 for the channel HieLow Enter Button Nothing Comes Close to a Cobra 13 Operation D Lelel
14. e charge Cherga Jack tab on top of your microTALK radio mm 2 Insert the plug into the speaker E microphone charge jack To connect a wall charger adapter 1 Open the speaker microphone charge tab on top of your microTALK radio 2 Insert the wall charger adapter plug into the speaker microphone charge jack fs English Signal Strength Signal Strength Meter Your microTALK radio has a Signal Strength Meter that shows the strength of your incoming and outgoing transmissions The ascending bars next to the signal strength indicate the strength of the signal The greater the number of bars visible the stronger the signal The fewer number of bars visible the weaker the signal microTALK Range Your range will vary depending on terrain and conditions Maximum Range In flat open country your radio will operate at maximum range Buildings and foliage in the path of the xy signal can reduce the range of the radio Reduced Range Dense foliage and hilly terrain will further reduce the range of the radio On FRS channels 8 through 14 your radio automatically switches to low power which will limit the range the radio can communicate Remember you can achieve maximum range by using maximum range extender See page 7 for details Nothing Comes Close to a Cobra 2 Operation h LJ EE Operation Scrolling through Mode Functions By scrolling through the Mode Functions you will
15. e laws They may not be thrown in the trash Certain states or municipalities require recycling and have established collection programs Please contact your local waste removal authority for instructions or return to Cobra for recycling Wrap batteries carefully and mail postage prepaid to Cobra Electronics Corporation 6500 West Cortland Street Chicago IL 60707 USA Attn Battery Recycling Do not put batteries into fire or expose to high heat They may explode Nothing Comes Close to a Cobra 1 h LJ EE Operation For charging microTALK radio s in desktop On Off Power Turning on Your microTALK Radio charger To turn on your radio 1 Insert radio s into desktop charger as shown 1 Rotate the On Off Volume knob clockwise 2 Insert round connector of 120 volt adapter to turn on your radio into jack on back of charger 2 Rotate the On Off Volume knob clockwise to 3 Plug 120 volt adapter into electrical outlet increase the volume or counterclockwise to If charging light is not on check position of radio Radio should be reduce the volume upright The charge indicator light will stay on as long as the radio Your microTALK radio is now in Standby is in the charging well even after the batteries are fully charged mode ready to receive transmissions The radio It normally takes about 15 hours to fully recharge batteries is always in Standby mode except when the Batteries will not be damaged if
16. ent on or off setting is displayed 2 Press the Channel Up or Channel Down button to turn keystroke tones on or off 3 Choose one of the following a Press the Lock Mode button to enter the new setting and return to Standby mode b Press the HieLow Enter button to enter the new setting and return to Standby mode Nothing Comes Close to a Cobra 23 General Specifications D z Fcc Li E Lice Operation introduction ESS General Specifications IMPORTANT NOTICE FCC LICENSE REQUIRED p This two way radio operates on GMRS General Mobile Radio Service frequencies FRS GMRS Frequency which require an FCC Federal Communications Commission license A user must be licensed prior to operating on Channels 1 through 7 on high power or 15 hrough 22 which comprise the GMRS channels of this radio Serious penalties could result for unlicensed use of GMRS channels in violation of FCC rules Operation of this radio is subject to additional rules specified in 47 C F R Part 95 Allocation and Compatibility Important Please note that Cobra GMRS models with 15 Channels may designate different channel numbers for the same frequency For example a Cobra 15 Channel GMRS model would need to be Licensed users will be issued a call sign by the FCC which should be used for tuned to Channel 11 in order to communicate with a 22 Channel station identification when operating this radio GMRS users should also cooperate GMRS tuned to
17. ical Assistance English only www cobra com on line Frequently Asked Questions English and Spanish productinfoecobra com e mail For Assistance Outside the U S A Contact Your Local Dealer 2005 Cobra Electronics Corporation 6500 West Cortland Street Z Chicago Illinois 60707 USA English www cobra com Introduction a g Introduction N s Wrist Strap Connector Q Belt Clip 8 Battery Compartment 9 Battery Door Antenna 9 Latch e External Speaker Microphone Charge Jack 8 Channel Down P Button Bee Channel Up Button 0 Lock Mode in Button UU HieLow Power Light Enter Button Max Range Button E Speaker Microphone fA2 English Features 22 Channels Seven shared with FRS GMRS seven FRS only eight GMRS only e 38 Privacy Codes Hands Free Operation VOX 10 Channel Memory Signal Strength Meter Scan Channel privacy codes memory e Selectable HieLow Power In GMRS Backlit LCD Display Button Lock Call Alert 10 selectable tones Speaker Microphone Charge Jack Roger Beep Selectable on off Battery Power Saver Keystroke Tones Selectable on off Auto Squelch Maximum Range Extender Belt Clip Backlit LCD Display Lock Icon 9 Keystroke Tones Icon e Roger Beep Icon Signal Strength Meter Icon HieLow e Power Ilcon
18. if you do not press any buttons for 15 seconds your radio will automatically return to Standby mode on the channel privacy code that was displayed before you entered mode functions Select Channel N e fis English During privacy code scan while receiving an incoming transmission you can choose from the following a Press and hold the Talk button to communicate on that channel privacy code Your radio will remain on that channel privacy code and return to Standby mode b Press the Channel Up or Channel Down button to resume scanning privacy codes If you press the Talk button while scanning but more than 10 seconds after receiving a transmission you will transmit on the channel privacy code on which you last received a transmission This will then return the radio to Standby mode If you do not press any button within 10 seconds your radio will automatically resume scanning privacy codes During privacy code scan while not receiving a transmission you can choose from the following a Press and hold the Talk button to communicate on the channel privacy code that was displayed before you entered mode functions or the channel privacy code on which during scanning you last received a transmission This will return the radio to Standby mode Press the Lock Mode button to proceed to set memory location scan see page 20 for further details Press the HieLow Enter button to return to Standby mode on the
19. ke design are registered trademarks of Cobra Electronics Corporation USA Cobra Electronics Corporation is a trademark of Cobra Electronics Corporation USA fs English The Cobra line of quality products includes CB Radios microTALK Radios Radar Laser Detectors e Safety Alert Traffic Warning Systems Handheld GPS Receivers Mobile GPS Navigation Systems HighGear Accessories CobraMarine VHF Radios Power Inverters Accessories Nothing Comes Close to a Cobra For more information or to order any of our products please visit our website www cobra com English
20. nel Up or Channel Down button to begin scanning channels The radio ignores specific privacy codes while scanning channels The Scan icon will continue to be displayed when scan is on Your radio will continue to scan all channels and stop if an incoming transmission is detected Your radio will remain on that channel for 10 seconds While setting channel scan if you do not press any buttons for 15 seconds your radio will automatically return to Standby mode on the channel or channel privacy code displayed before you entered mode functions During channel scan while receiving an incoming transmission you can choose from the following a Press and hold the Talk button to communicate on that channel Your radio will remain on that channel and return to Standby mode b Press the Channel Up or Channel Down button to resume scanning channels If you press the Talk button while scanning but more than 10 seconds after receiving a transmission you will transmit on the channel on which you last received a transmission This will return the radio to Standby mode If you do not press any button within 10 seconds after receiving a scanned transmission your radio will automatically resume scanning channels During channel scan while not receiving a transmission you can choose from the following a Press and hold the Talk button to communicate on the channel or channel privacy code that was displayed before you entered mode func
21. ode button to enter the new setting and proceed to other functions b Press the HieLow Enter button to enter the new setting and return to Standby mode c Do not press any buttons for 15 seconds to enter the new setting and return to Standby mode Lock Mode Button el Nothing Comes Close to a Cobra 17 Operation h LJ EE Operation Voice Activated Transmit VOX In VOX mode your microTALK radio can be used hands free automatically transmitting when you speak You can set the VOX sensitivity level to fit the volume of your voice and avoid transmissions triggered by background noise enr To turn VOX mode on or off 1 Press the Lock Mode button until the VOX icon flashes on the display The current on or off setting is displayed 2 Press the Channel Up or Channel Down button to turn VOX on or off 3 Choose one of the following a Press the Lock Mode button to enter the selected on or off setting and proceed to other functions b Press the HieLow Enter button to enter the selected on or off setting and return to Standby mode To set VOX sensitivity 1 Press the Lock Mode button until the VOX icon flashes and the current sensitivity level is displayed with letters LE and a Number 01 through 05 with Number 05 being the most sensitive level and Number 01 being the least sensitive level The current sensitivity level is displayed 2 Press the Channel Up or Channel Down
22. response f English Nothing Comes Close to a Cobra 3 h J le o Operation introduction ESS Talk Button Communicating with Another Person I iw To talk to another person Listening for a Response When you are finished talking 1 Press and hold the Talk button Release the Talk button to receive incoming 2 With the microphone about two inches transmissions Your microTALK radio is Two Inches five five cm from your mouth speak in a always in Standby mode while the Talk or SIGUE normal voice Call buttons are not pressed 3 Release the Talk button when you are Volume Knob Volume finished talking and listen for a response To adjust the volume You cannot receive incoming calls while pressing the Talk button Rotate the On Off Volume knob Both radios must be tuned to Call Button Call Button the same channel privacy code E a y To alert another person that you are calling to communicate lemme Press and release the Call button Ch I The other person will hear a two second Channel Buttons annes call tone This tone is used only to establish To select a channel voice communications With the radio on select any of the 22 channels by pressing the Channel Up See page 22 on how to select from or Channel Down button 10 available call tone settings Both radios must be tuned to the same channel to communicate GMRS Channels 8 through 14 are FRS only Channels 15 through 22
23. they stay in the charging well Talk Call or Lock Mode buttons are pressed longer than that Battery Low Each port can charge one radio Uses 120 Volt adapter Use only i radi 3 Cobra NiMH batteries model GA BN with charger model GA CD ox Your microTALK radio has a battery level meter a that shows when battery power is decreasing Cobra recommends your radio is turned off while being charged The greater the number of bars visible the stronger the battery level When the battery level is low the last bar and bALo will flash The Basics to Get You Started indicating your batteries should be replaced or Your microTALK radio is easy to use if using rechargeable batteries recharged To get started simply peers Auto Battery Save 1 Rotate the On Off Volume knob to turn a Your microTALK radio has a unique circuit Battery Low on your radio ger Sav designed to extend battery life If there are 2 Press the Channel Up or Channel Down im paN y no transmissions for 10 seconds the radio will button to select a channel automatically switch to Battery Save mode and the Power Saver icon will flash in the display This will not affect the radio s ability to receive incoming transmissions Both radios must be tuned to the same channel privacy code to communicate 3 Press and hold the Talk button while speaking into the microphone 4 When finished talking release the Talk button and listen for a
24. tion After 10 seconds of inactivity unit restarts scan b Press the Channel Up or Channel Down button to resume scanning memory locations If you press the Talk button while scanning but more than 10 seconds after receiving a transmission you will transmit on the memory location on which during scanning you last received a transmission After 10 seconds of inactivity unit restarts scan If you do not press any button within 10 seconds your radio will automatically resume scanning memory locations During memory location scan while not receiving a transmission you can choose from the following a Press and hold the Talk button to communicate on the channel privacy code that was displayed before you entered mode functions or memory location on which during scanning you last received a transmission After 10 seconds of inactivity unit restarts scan Press the Lock Mode button to proceed to other functions Press the HieLow Enter button to return to Standby mode on the channel privacy code that was displayed before you entered mode functions or the memory location on which during scanning you last received a transmission To reduce the number of memory locations being scanned you may de program any unwanted locations See page 15 to de program a memory location o c Nothing Comes Close to a Cobra 21 Operation LJ EE Operation h 10 Call Tone Settings You can choose from 10 different call
25. tions or the channel on which during scanning you last received a transmission This will then return the radio to Standby mode Press the Lock Mode button to proceed to set privacy code scan on the channel that was either displayed before you entered mode functions or on which during channel scanning you last received a transmission see page 18 for further details Press the HieLow Enter button to return to Standby mode on the channel privacy code that was displayed before you entered mode functions or the channel on which during scanning you last received a transmission c e Nothing Comes Close to a Cobra Operation h e peono Operation Privacy Code Scan Your microTALK radio can automatically scan the Privacy Codes 01 through 38 within one channel To scan privacy codes 1 While in Standby mode press the Channel Up or Channel Down button to choose the channel on which you wish to scan privacy codes Press the Lock Mode button until the Scan icon and the privacy code numbers flash on the display Press the Channel Up or Channel Down button to begin scanning privacy codes within the channel you selected The Scan icon will continue to be displayed when privacy code scan is on Your radio will continue to scan privacy codes and stop as an incoming transmission is detected Your radio will remain on that channel privacy code for 10 seconds While setting privacy code scan
26. tone settings to transmit a unique call alert To change a call tone setting 1 Press the Lock Mode button until the letter C and the current call tone number 01 through 10 is displayed 2 Press the Channel Up or Channel Down button to hear the other call tone settings 3 Choose one of the following a Press the Lock Mode button to enter the new setting and proceed to other functions b Press the HieLow Enter button to enter the new setting and return to Standby mode Lock Mode Button Roger Beep Confirmation Tone Roger Beep is an audible tone that your listener will hear when you release the Talk button This alerts the other party that you are finished talking and it is OK for them to speak To turn roger beep on or off 1 Press the Lock Mode button until the Roger Beep icon flashes on the display The current on or off setting is displayed 2 Press the Channel Up or Channel Down button to select roger beep on or off 3 Choose one of the following a Press the Lock Mode button to enter the new setting and proceed to other functions b Press the HieLow Enter button to enter the new setting and return to Standby mode Lock Mode Button Keystroke Tones With Keystroke Tones turned on your radio will sound beeps each time you press a button or change a setting T To change keystroke tones 1 Press the Lock Mode button until the Keystroke Tones icon flashes on the display The curr
27. w Important 7 7 FRS GMRS 462 7125 High or Low FCC RF Exposure Requirements For body worn operation this radio has 8 FRS 467 5625 Low been tested and meets the FCC RF exposure guidelines when used with Cobra 9 FRS 467 5875 Low accessories supplied or designated for this product Use of other accessories 10 FRS 467 6125 Low may not ensure compliance with FCC RF exposure guidelines Use only the 11 FRS 467 6375 L supplied antenna Unauthorized antennas modifications or attachments z ow could damage the transmitter and may violate FCC regulations 12 FRS 467 6625 Low 13 FRS 467 6875 Low Normal Position 14 FRS 467 7125 Low Hold the transmitter approximately two inches from your face and 15 11 GMRS 462 5500 High or Low speak in a normal voice with the antenna pointed up and away 16 8 GMRS 462 5750 High or Low en E EEG z is device complies with part 15 of the ules Operation is subject 17 12 GMRS 462 6000 High or Low to the following two conditions 1 This device may not cause harmful 18 9 GMRS 462 6250 High or Low interference and 2 this device must accept any interference received 19 13 GMRS 462 6500 High or Low including interference that may cause undesired operation 20 10 GMRS 462 6750 High or Low FCC Warnings Replacement or substitution of transistors regular diodes or y other parts of a unique nature with parts other than those recommended by 21 14 GMRS 462 7000 High or Low Cobra may cause a violation of the technical regulations of part

Download Pdf Manuals

image

Related Search

Related Contents

HDC-30X形 - 日立リビングサプライ  Hygiène alimentaire  

Copyright © All rights reserved.
Failed to retrieve file